L7FEC86S USER MANUAL FR Notice d'utilisation Lave-linge
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ.................................................................................3 2. CONSIGNES DE SÉCURITÉ........................................................................................4 3. INSTALLATION............................................................................................................6 4. DESCRIPTION DE L'APPAREIL.................................................................................10 5.
FRANÇAIS 1. 3 INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • La pression de l'eau en service au niveau du point d'entrée en provenance de l'arrivée d'eau doit être comprise entre 0,5 bar (0,05 MPa) et 8 bar (0,8 MPa). Les orifices d'aération situés à la base (si présents) ne doivent pas être obstrués par de la moquette, un tapis, ou tout type de revêtement de sol. L'appareil doit être raccordé à l'arrivée d'eau à l'aide des tuyaux neufs fournis, ou d'autres tuyaux neufs fournis par le service après-vente agréé.
FRANÇAIS service après-vente agréé pour connaître les accessoires disponibles. 2.2 Branchement électrique • L'appareil doit être relié à la terre. • Utilisez toujours une prise de courant de sécurité correctement installée. • Vérifiez que les paramètres figurant sur la plaque signalétique correspondent aux données électriques de votre réseau. • N'utilisez pas d'adaptateurs multiprises ni de rallonges. • Veillez à ne pas endommager la fiche secteur ni le câble d'alimentation.
www.aeg.com 3. INSTALLATION AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 3.1 Déballage AVERTISSEMENT! Retirez l'intégralité de l'emballage et les boulons de transport avant d'installer l'appareil. AVERTISSEMENT! Servez-vous de gants. 4. Ouvrez le hublot et retirez la cale en polystyrène du joint du hublot, ainsi que tous les articles présents dans le tambour. 1. Retirez le film externe. Si nécessaire, utilisez un cutter. 2.
FRANÇAIS x4 1 7 A 2 8. Nettoyez soigneusement et séchez le bas de l'appareil. ATTENTION! N'utilisez pas d'alcool, de solvants ni de produits chimiques. 9. Veillez à identifier la taille et l'emplacement des différents isolants acoustiques. Reportez-vous à l'illustration : B Fixez les isolants acoustiques à température ambiante. 13. Remettez l'appareil en position verticale. 14. Retirez le câble d'alimentation électrique et le tuyau de vidange de leurs supports.
www.aeg.com 16. Retirez les entretoises en plastique. 17. Placez les caches en plastique, fournis dans le sachet du manuel d'utilisation, dans les trous. x4 L'appareil doit être de niveau et stable. Une mise de niveau correcte évite les vibrations, le bruit ou des déplacements de l'appareil au cours de son fonctionnement. Nous vous recommandons de conserver l'emballage et les boulons de transport en vue d'un éventuel déplacement de l'appareil. 3.2 Positionnement et mise de niveau 1.
FRANÇAIS 9 La partie rouge dans la fenêtre « A » témoigne de ce dysfonctionnement. 45 20 O O Assurez-vous que le tuyau d'arrivée d'eau n'est pas en position verticale. 3. Si nécessaire, desserrez la bague de serrage pour bien le positionner. 4. Raccordez le tuyau d'arrivée d'eau à un robinet d'eau froide fileté (3/4 pouce). ATTENTION! Assurez-vous que les raccords ne fuient pas. N'utilisez pas de rallonge si le tuyau d'alimentation est trop court.
www.aeg.com Vérifiez que l'extrémité du tuyau de vidange n'est pas plongée dans l'eau. Il pourrait y avoir un reflux d'eau sale dans l'appareil. 3. À une conduite fixe dotée d'une ventilation spéciale : insérez directement le tuyau dans la conduite d'évacuation. Reportezvous à l'illustration. L'extrémité du tuyau de vidange doit être ventilée en permanence, c'est-à-dire que le diamètre interne du conduit d’évacuation (minimum 38 mm - min.
FRANÇAIS du programme en 30 secondes. Le programme de lavage est défini sur mesure pour la charge et le type de linge, sans consommer davantage de temps, d'énergie ou d'eau que nécessaire. • La vapeur est un moyen rapide et simple de rafraîchir les vêtements. Les programmes à la vapeur éliminent les odeurs et les plis en douceur sur les textiles secs, facilitant ainsi le repassage. L'option Plus Steam termine chaque cycle par une phase de vapeur douce qui détend les fibres et réduit le froissage.
www.aeg.com 5. BANDEAU DE COMMANDE 5.1 Description du bandeau de commande 3 2 1 Programma/Programme Katoen Blanc/Couleurs Synthetica Synthétiques Fijne Was Délicats Wol/Zijde Laine/Soie Eco Tijd Besparen Gain de temps 4 Stoom Vapeur Anti-Allergie Anti-Allergies 20 min.
FRANÇAIS 13 5.2 Affichage Voyant de charge maximale. Le voyant clignote lors de l'estimation de la charge de linge (consultez le paragraphe « Détection de la charge PROSENSE »). Voyant de charge maximale. Il clignote lorsque la charge de linge dépasse la charge maximale prévue pour le programme sélectionné. Indicateur Départ différé. Voyant Hublot verrouillé. L'indicateur numérique peut afficher : • La durée du programme (par ex. • Le départ différé (par ex. ou ). ). • La fin du cycle ( ).
www.aeg.com Voyant Gain de temps. Indicateur de température. Le voyant tionnez un lavage à froid. apparaît lorsque vous sélec- Indicateur de vitesse d'essorage. Voyant Arrêt cuve pleine. Voyant Extra silence. Voyant de prélavage. Voyant Détachage. Voyant Rinçage plus. 6. SÉLECTEUR ET TOUCHES 6.1 AAN /UIT - MARCHE/ ARRÊT Appuyez sur cette touche pendant quelques secondes pour allumer et éteindre l'appareil. Deux différents signaux sonores retentissent lorsque vous allumez ou éteignez l'appareil.
FRANÇAIS 6.4 TPM Lorsque vous sélectionnez un programme, l'appareil règle automatiquement la vitesse d'essorage maximale. Appuyez à plusieurs reprises sur cette touche pour : • Diminuer la vitesse d'essorage. Seules les vitesses disponibles pour le programme sélectionné s'affichent. • Activer l'option Arrêt cuve pleine. L'eau du dernier rinçage n'est pas évacuée afin d'éviter le froissage du linge. Le programme de lavage se termine avec de l'eau dans le tambour, et l'essorage final n'est pas effectué.
www.aeg.com Le voyant indique le nombre de rinçages sélectionné. Cette option allonge la durée du programme. Si l'option Spoelen+ Rinçage+ est définie comme une option par défaut et que vous sélectionnez un programme de lavage, s'affiche. Dans ce cas, en appuyant sur la touche Spoelen+ - Rinçage+, il est possible de n'ajouter qu'un seul rinçage. 6.7 Plus Steam Cette option ajoute une phase vapeur, suivie par une courte phase antifroissage à la fin du programme de lavage.
FRANÇAIS • Essorage uniquement en appuyant deux fois. L'appareil supprime les phases de lavage et de rinçage. • Vidange uniquement en appuyant trois fois. L'appareil effectue uniquement une phase de vidange. Si vous appuyez une quatrième fois sur la touche, l'appareil propose à nouveau un réglage par défaut du programme de lavage. 6.11 Startuitstel - Départ différé Cette option vous permet de différer le départ du programme à un moment qui vous convient mieux.
www.aeg.com Programme Description du programme Lainages lavables en machine, laine lavable à la main et Wol/Zijde - Laine/Soie (Laine/Soie) textiles délicats portant le symbole « lavable à la main ».1) Programme vapeur Programme vapeur pour les articles en coton et textiles Stoom - Vapeur (Vapeur) synthétiques. La vapeur peut être utilisée pour le linge sec2) Linge propre ou porté une seule fois. Ce programme réduit les plis et les odeurs3) et détend les fibres.
FRANÇAIS 19 Programme Description du programme Outdoor (Blousons) Articles de sport synthétiques. Ce programme est conçu pour laver en douceur les vêtements de sport modernes comme les vêtements pour la gym, le cyclisme, le jogging, et les vêtements d'extérieur similaires. La charge de linge recommandée est de 2.5 kg. Pour obtenir de meilleurs résultats, n'utilisez pas d'adoucissant et assurez-vous que le distributeur de produit de lavage ne contient pas de résidus d'adoucissant.
www.aeg.com Programme Description du programme Le cycle de maintenance à l'eau chaude sert à nettoyer et rafraîchir le tambour, ainsi qu'à éliminer les résidus qui pourMachine Clean (Nettoyage de l'appareil) raient entraîner la formation de mauvaises odeurs. Pour des résultats optimaux, effectuez ce cycle une fois par mois. Avant d'effectuer ce cycle, retirez tous les articles du tambour.
FRANÇAIS Programme Température par défaut Plage de températures Vitesse d'essorage maximale Plage de vitesses d'essorage Anti-Allergie - AntiAllergies 60 °C 1600 tr/min 1600 tr/min 400 tr/min 8 kg 20 min. - 3 kg 30 °C 40 °C - 30 °C 1200 tr/min 1200 tr/min 400 tr/min 3 kg Outdoor 30 °C 40 °C - Froid 1200 tr/min 1200 tr/min 400 tr/min Jeans 40 °C 60 °C - Froid 1200 tr/min 1200 tr/min 400 tr/min Machine Clean 60 °C 1200 tr/min 1200 tr/min 400 tr/min 21 Charge maximale 2.
Voorwas - Prélavage ■ ■ ■ ■ ■ Spoelen+ - Rinçage+ ■ ■ ■ ■ ■ Eco 2) ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Startuitstel - Départ différé ■ ■ ■ ■ ■ ■ ■ ■ Plus Steam 1) ■ ■ Soft Plus ■ ■ Tijd Besparen Gain de temps 3) Rinçage uniquement Essorage uniquement Vidange uniquement ■ Machine Clean ■ Jeans ■ Outdoor ■ 20 min.
FRANÇAIS 7.2 Woolmark Apparel Care Bleu 23 le lavage des vêtements en laine portant une étiquette « lavage à la main », sous réserve que les vêtements soient lavés conformément aux instructions mentionnées par le fabricant de ce lavelinge. Respectez les instructions de séchage figurant sur l'étiquette des vêtements et toutes les autres instructions concernant le linge. M1623 Au Royaume-Uni, en Irlande, à Hong Kong ainsi qu'en Inde, le symbole Woolmark est une marque de certification.
www.aeg.com • L'appareil présente une anomalie de fonctionnement (suite de signaux courts pendant environ 5 minutes). Pour désactiver/activer les signaux sonores, appuyez simultanément sur les touches Spoelen+ - Rinçage+ et Startuitstel - Départ differé pendant 6 secondes. Si vous désactivez les signaux sonores, ils continueront à retentir si l'appareil présente une anomalie. jusqu'à ce que le voyant correspondant s'allume/s'éteigne. Cette option ajoute deux rinçages et s'affiche. 9.
FRANÇAIS 10.3 Ajout du produit de lavage et des additifs 25 1 2 3. Pour utiliser de la lessive en poudre, tournez le volet vers le haut. Compartiment destiné à la phase de prélavage, au programme de trempage ou à un produit détachant. Compartiment pour la phase de lavage. Compartiment réservé aux additifs liquides (assouplissant, amidon). Niveau maximal pour la quantité d'additifs liquides. Volet pour produit de lavage en poudre ou liquide.
www.aeg.com Avec le volet en position BASSE : • N'utilisez pas de lessives liquides gélatineuses ou épaisses. • Ne versez pas de lessive liquide audelà du niveau maximal indiqué sur le volet. • Ne sélectionnez pas de phase de prélavage. • Ne sélectionnez pas la fonction Départ différé. 5. Dosez le produit de lavage et l'assouplissant. 6. Fermez soigneusement le distributeur de produit de lavage. 3. Si nécessaire, sélectionnez une ou plusieurs options en appuyant sur les touches correspondantes.
FRANÇAIS l'appareil en pause. Le voyant correspondant clignote. 2. Appuyez à plusieurs reprises sur la touche Startuitstel - Départ différé jusqu'à ce que s'affiche. 3. Appuyez de nouveau sur la touche Start/Pauze - Départ Pause pour lancer le programme immédiatement. Modification du départ différé au cours du décompte Pour modifier le départ différé : 1. Appuyez sur la touche Start/Pauze Départ Pause pour mettre l'appareil en pause. Le voyant correspondant clignote. 2.
www.aeg.com La phase à la vapeur est en cours : . La phase anti-froissage est en cours : . 10.10 Interruption d'un programme et modification des options Lorsque le programme est en cours, vous ne pouvez changer que quelques options : 1. Appuyez sur la touche Start/Pauze Départ Pause. Le voyant correspondant clignote. 2. Modifiez les options. Les informations données sur l'affichage changent en conséquence. 3. Appuyez à nouveau sur la touche Start/Pauze - Départ Pause.
FRANÇAIS 4. Laissez le hublot et la boîte à produits entrouverts pour éviter la formation de moisissures et l'apparition de mauvaises odeurs. 5. Fermez le robinet d'eau. 10.14 Vidange de l'eau après la fin du cycle Si vous avez sélectionné un programme ou une option qui ne vidange pas l'eau du dernier rinçage, le programme se termine, mais : • L'indicateur , le voyant d'option ou et le voyant Hublot fermé s'affichent. Le voyant de la phase en cours clignote.
www.aeg.com • Videz les poches et retournez-les. • Retournez les tissus multi-couches, en laine et les articles portant des illustrations imprimées vers l'intérieur. • Traitez au préalable les taches tenaces. • Lavez les taches incrustées avec un produit spécial. • Traitez les rideaux avec précautions. Retirez les crochets et placez les rideaux dans un sac de lavage ou une taie d'oreiller. • Ne lavez pas d'articles sans ourlet ou déchirés.
FRANÇAIS 31 Utilisez la bonne quantité d'adoucisseur d'eau. Respectez les instructions qui se trouvent sur les emballages du produit. 12. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 12.1 Nettoyage extérieur Nettoyez uniquement l'appareil à l'eau chaude avec un savon doux. Séchez complètement toutes les surfaces. augmentation des bactéries et la formation d'un biofilm à l'intérieur du tambour et de la cuve.
www.aeg.com 12.6 Nettoyage du distributeur de produit de lavage Pour éviter les dépôts de lessive séchée, d'assouplissant coagulé et/ou la formation de moisissures dans le distributeur de produit de lavage, veillez à effectuer régulièrement la procédure de nettoyage suivante : 1. Ouvrez le distributeur. Appuyez sur le loquet vers le bas comme indiqué sur l'illustration, puis retirez le distributeur. 1 4. Réinstallez le distributeur de lavage dans ses rails et fermez-le.
FRANÇAIS 33 AVERTISSEMENT! • Ne retirez pas le filtre pendant que l'appareil fonctionne. • Ne nettoyez pas la pompe de vidange si l'eau contenue dans l'appareil est chaude. Si nécessaire, attendre que l’eau refroidisse Procéder comme suit pour le nettoyage de la pompe : 1. Ouvrez le couvercle de la pompe. 5. Lorsque le récipient est rempli d'eau, refermez la conduite de vidange et videz le récipient. 6. Répétez les étapes 4 et 5 jusqu'à ce que l'eau cesse de sortir. 2 1 2 1 2.
www.aeg.com 2 1 10. Nettoyez le filtre sous l'eau courante. Lorsque vous appliquez la procédure de vidange d'urgence, vous devez réactiver le système de vidange : a. Versez 2 litres d'eau dans le distributeur de produit de lavage pour le lavage principal. b. Démarrez le programme pour vidanger l'eau. 12.8 Nettoyage du tuyau d'arrivée d'eau et du filtre de la vanne 11. Replacez le filtre dans les guides prévus en le tournant dans le sens horaire.
FRANÇAIS 35 dans le paragraphe « Nettoyage du filtre de vidange ». Si nécessaire, nettoyez la pompe. Lorsque vous vidangez l'eau avec la vidange d'urgence, vous devez réactiver le système de vidange : 1. Versez 2 litres d'eau dans le distributeur de produit de lavage pour le lavage principal. 2. Démarrez le programme pour vidanger l'eau. 3. Utilisez une brosse à dents pour nettoyer le filtre de la valve situé à l'arrière de l'appareil. 12.
www.aeg.com 13. EN CAS D'ANOMALIE DE FONCTIONNEMENT AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 13.1 Introduction L'appareil ne démarre pas ou s'arrête en cours de programme. Dans un premier temps, essayez de trouver une solution au problème (reportez-vous au tableau). Si le problème persiste, contactez le service après-vente agréé.
FRANÇAIS Problème 37 Solution possible Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte. Désactivez la sécurité enfants si elle a été préalablement activée. L'appareil ne se remplit pas d'eau correctement. Assurez-vous que le robinet d'eau est ouvert. Assurez-vous que la pression de l'arrivée d'eau n'est pas trop basse. Pour obtenir cette information, contactez votre compagnie des eaux. Assurez-vous que le robinet d'eau n'est pas obstrué.
www.aeg.com Problème Solution possible Répartissez manuellement les vêtements dans la cuve et lancez à nouveau la phase d'essorage. Ce problème peut résulter de problèmes d'équilibrage. Il y a de l'eau sur le sol. Assurez-vous que les raccords des tuyaux d'eau sont bien serrés et qu'il n'y a aucune fuite d'eau. Assurez-vous que le tuyau de vidange n'est pas endommagé. Assurez-vous d'utiliser une lessive adaptée en quantité correcte.
FRANÇAIS 39 Problème Solution possible À la fin du cycle de lavage, il y a des résidus de produit de lavage dans le distributeur de produit de lavage. Assurez-vous que le volet est dans la bonne position (vers le HAUT pour la lessive en poudre, vers le BAS pour la lessive liquide). Veillez à utiliser le distributeur de produit de lavage en suivant les indications données dans ce manuel d'utilisation. Après avoir effectué ces contrôles, mettez l'appareil en marche.
www.aeg.com 14. VALEURS DE CONSOMMATION Les données de ce tableau sont approximatives. Les données peuvent varier pour différentes raisons : la quantité et le type de linge, la température ambiante ou de l'eau. Au cours du programme de lavage, la technologie Prosense peut faire varier la durée du lavage et les valeurs de consommation. Pour plus de détails, consultez le paragraphe« La détection de charge Prosense » du chapitre « Utilisation quotidienne ».
FRANÇAIS 41 15.
www.aeg.com Pour surélever votre appareil et faciliter le chargement et le déchargement du linge. Assurez-vous de la compatibilité du kit de superposition en vérifiant la profondeur de vos appareils. Le kit de superposition peut uniquement être utilisé avec les appareils indiqués dans la brochure fournie avec l'accessoire. Le tiroir peut servir au stockage du linge comme par ex. : les serviettes ainsi que des produits de nettoyage et autres. Lisez attentivement la notice fournie avec l'accessoire.
FRANÇAIS 43
157003831-A-462016 www.aeg.