L7FEC96S USER MANUAL EN User Manual Washing Machine
www.aeg.com CONTENTS 1. SAFETY INFORMATION.................................................................................................3 2. SAFETY INSTRUCTIONS................................................................................................ 4 3. INSTALLATION............................................................................................................... 5 4. PRODUCT DESCRIPTION............................................................................................
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • The ventilation opening in the base (if applicable) must not be covered by a carpet, mat, or any floor covering. The appliance must be connected to the water mains using the new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre. Old hose sets must not be reused. If the mains power supply cable is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an electrical hazard.
ENGLISH • • • • cable. Should the mains cable need to be replaced, this must be carried out by our Authorised Service Centre. Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. Do not touch the mains cable or the mains plug with wet hands. Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. This appliance complies with the E.E.C. Directives. 2.
www.aeg.com 7. Remove the polystyrene protection from the bottom. 1 3. Remove the internal film. 2 8. Fully clean and dry the bottom of the appliance. 4. Open the door and remove the polystyrene piece from the door seal and all the items from the drum. CAUTION! Do not use alcohol, solvents or chemical products. 9. Make sure to identify the different sizes and the positions of the sound barriers. Refer to the illustration: 5. Carefully put down the appliance with the rear side on it. 6.
ENGLISH 12. Refer to the illustration. Make sure that the barriers are securely attached. x4 A B 16. Pull out the plastic spacers. 17. Put the plastic caps, that you find in the user manual bag, in the holes. Attach the sound barriers at a room temperature. 13. Pull up the appliance in vertical position. We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.2 Positioning and levelling 14.
www.aeg.com 45 20 O O x4 The appliance must be level and stable. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. 3.3 The inlet hose 1. Connect the water inlet hose to the back of the appliance. 2. Position it toward left or right depending on the position of the water tap. Make sure that the inlet hose is not in vertical position. 3. If necessary, loose the ring nut to set it in the correct position. 4.
ENGLISH A 9 Make sure that the drain hose end is not immersed in the water. There may be a return of dirty water into the appliance. 3. To a stand pipe with vent-hole Insert the drain hose directly into a drain pipe. Refer to the illustration. If this occur, close the water tap and contact the authorized service centre to replace the hose. 3.5 Water drainage The drain hose should stay at a height of not less than 60 cm and not more than 100 cm.
www.aeg.com Make sure that the drain hose makes a loop to prevent particles going into the appliance from the sink. 6. Position the hose directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. 4. PRODUCT DESCRIPTION 4.
ENGLISH 11 4.2 Appliance overview 1 2 9 8 3 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Worktop Detergent dispenser Control panel Door handle Rating plate Drain pump filter Feet for levelling the appliance 8 9 10 11 12 Drain hose Inlet hose connection Mains cable Transit bolts Hose support 5. CONTROL PANEL 5.
www.aeg.
ENGLISH 13 The digital indicator can show: ). • Programme duration (e. g. • Delay time (e. g. or ). • Cycle end ( ). • Warning code (e.g. ). Energy saving indicators. The indicator appears by selecting a programme for cotton at 40 °C or 60 °C. Washing phase indicator: it flashes during prewash and wash phase. Rinsing phase indicator: it flashes during rinse phase. The indicator appears when the Soft Plus option is activated. Spin and drain phase indicator. It flashes during spin and drain phase.
www.aeg.com 6.2 Introduction The options/functions are not selectable with all washing programmes. Check the compatibility between options/functions and washing programmes in the "Programme Chart". An option/function can exclude another one, in this case the appliance doesn't allowed you to set the incompatible options/functions together. 6.3 Temp.°C When you select a washing programme, the appliance automatically proposes a default temperature.
ENGLISH This option is recommended for heavily soiled laundry, especially if containing sand, dust , mud and other solid particles. This option can increase the programme duration. 6.6 Spoelen+ - Rinçage+ With this option you can add up to 3 rinses accordingly to the selected washing programmes. Useful for people allergic to detergents and in areas where the water is soft. indicator shows the selected The number of rinses. This option increases the programme duration.
www.aeg.com All set options (except permanent extra rinse) are deselected automatically. • Only spin at second touch. The appliance skips wash and rinse phase. • Only drain at third touch. The appliance performs only the drain phase. At firth touch the appliance proposes the default setting of the washing programme again. 6.11 Startuitstel - Départ différé Touch repeatedly the button to set the required delay. The time increases by steps of 30 minutes up to 90' and from 2 hours up to 20 h.
ENGLISH Programme 17 Programme description Machine washable wool, hand washable wool and delicate Wol/Zijde - Laine/Soie (Wool/Silk) fabrics with «hand washing» care symbol.1) Steam programme Steam programme for cotton and synthetic items. Steam Stoom - Vapeur (Steam) can be used for dried2), washed or worn once laundry. This programme reduce creases and odours3) and relaxes the fibers. When the programme is completed, quickly remove the laundry from the drum.
www.aeg.com Programme Programme description Outdoor (Outdoor) Synthetic sport items. This programme is designed to gently and quickly wash modern sports clothes such as gym, cycling or jogging clothes and similar outdoor items. The recommended laundry load is 2.5 kg. To reach better results, do not use fabric softener and make sure that there is no softener residue in the detergent dispenser. Waterproof, waterproof-breathable fabrics.
ENGLISH Programme temperature, maximum spin speed and maximum load Programme Default temperature Maximum spin speed Maximum load Temperature range Spin speed range 40 °C 95 °C - Cold 1600 rpm 1600 rpm - 400 rpm 9 kg 40 °C 60 °C - Cold 1200 rpm 1200 rpm - 400 rpm 4 kg 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 4 kg 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 1.5 kg - - 1.5 kg 60 °C 1600 rpm 1600 rpm - 400 rpm 9 kg 20 min.
www.aeg.
ENGLISH 7.2 Woolmark Apparel Care Blue 21 Company for the washing of wool garments labelled as «hand wash» provided that the garments are washed according to the instructions issued by the manufacturer of this washing machine. Follow the garment care label for drying and other laundry instructions. M1230 In UK, Eire, Hong Kong and India the Woolmark symbol is a certification trademark. The wool wash cycle of this machine has been approved by The Woolmark 8. BEFORE FIRST USE 1.
www.aeg.com If you deactivate the acoustic signals, they continue operate when the appliance has a malfunction. 9.3 Permanent Extra Rinse With this option you can permanently have an extra rinse when you set a new programme. • To activate/deactivate this option touch the Spoelen+ - Rinçage+ button and the Extra button simultaneously the relevant indicator comes on/goes off. This option adds two rinses and the display shows 9.
ENGLISH 10.3 Filling the detergent and additives 23 1 2 3. To use powder detergent, turn the flap up. Compartment for prewash phase an soak programme. Compartment for washing phase. Compartment for liquid additives (fabric conditioner, starch). Maximum level for quantity of liquid additives. Compartment for stain remover. Flap for powder or liquid detergent.
www.aeg.com With the flap in the position DOWN: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid detergent than the limit shown on in the flap. • Do not set the prewash phase. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser. In case a selection is not possible, no indicator comes on and an acoustic signal sounds. 10.
ENGLISH Changing the delay start after the countdown has started this case, it will be not possible to guarantee the best washing results. To change the delay start: 1. Touch the Start/Pauze - Départ Pause button to pause the appliance. The related indicator flashes. 2. Touch the Startuitstel - Départ différé button repeatedly until the display shows the desired delay time. 3. Touch the Start/Pauze - Départ Pause button again to start the new countdown. 10.
www.aeg.com 3. Touch the button Start/Pauze Départ Pause again. The washing programme continues. 10.11 Cancelling a running programme 1. Press the button AAN /UIT to cancel the programme and to deactivate the appliance. 2. Press the button AAN /UIT again to activate the appliance. Now, you can set a new washing programme. If the ProSense phase is already carried out and the water filling is already started, the new programme starts without repeating the ProSense phase.
ENGLISH • If you have set , the appliance drains the water and spins. • If you have set , the appliance only drains the water. The option indicator or goes out, while the indicator flashes and then goes off. 3. When the programme is completed and the door locked indicator goes off, you can open the door. 4. Press the AAN /UIT button a few seconds to deactivate the appliance. In any case, the appliance empties the water out automatically after approximately 18 hours. 10.
www.aeg.com Special stain removers are available. Use the special stain remover that is applicable to the type of stain and fabric. 11.3 Detergents and other treatments • Only use detergents and other treatments specially made for washing machines: – powder detergents for all types of fabric, – powder detergents for delicate fabrics (40 °C max) and woollens, – liquid detergents, preferably for low temperature wash programmes (60 °C max) for all types of fabric, or special ones for woollens only.
ENGLISH Always follow the instructions that you find on the packaging of the product. 12.3 Maintenance wash The repeated and prolonged use of low temperature programmes can cause detergent deposits, fluff residues, bacterial growth and biofilm formation inside the drum and the tub. This could generate bad odours and mildew. To eliminate these deposits and hygienize the inner part of the appliance, run a maintenance wash regularly (at least once a month): 1. Remove all laundry from the drum. 2.
www.aeg.com 3. Make sure that all detergent residue is removed from the upper and lower part of the recess. Use a small brush to clean the recess. WARNING! • Do not remove the filter while the appliance operates. • Do not clean the pump if the water in the appliance is hot. Wait until the water cools down Proceed as follows to clean the pump: 1. Open the pump cover. 4. Insert the detergent drawer into the guide rails and close it. Run the rinsing programme without any clothes in the drum. 2 1 2.
ENGLISH 31 5. When the bowl is full of water, close the drainage duct back and empty the container. 6. Repeat the steps 4 and 5 until the water stops to flow out. 2 1 11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 7. Close the drainage duct and turn the filter anti-clockwise to remove it. 2 1 2 1 12. Close the pump access. 8. If it is necessary, remove fluff and objects from the filter recess. 9.
www.aeg.com 12.8 Cleaning the inlet hose and the valve filter It is recommended to clean both the filters of the inlet hose and valve occasionally to remove any deposit, collected over the time: 1. Remove the inlet hose from the tap and clean the filter. 45° 20° 1 12.9 Emergency drain 2 3 2. Remove the inlet hose from the appliance by loosening the ring nut. If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain filter' paragraph.
ENGLISH 33 13. TROUBLESHOOTING WARNING! Refer to Safety chapters. 13.1 Introduction The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre. In case of major problems, the acoustic signals operate, the display shows an alarm code and the Start/Pauze - Départ Pause button may flash continuously: • - The appliance does not fill with water properly.
www.aeg.com Problem Possible solution Deactivate the Child Lock function, if it is on. The appliance does not fill with water properly. Make sure that the water tap is open. Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. Make sure that the water tap is not clogged. Make sure that the filter of the inlet hose and the filter of the valve are not clogged. Refer to “Care and cleaning”.
ENGLISH Problem Possible solution You cannot open the appliance door. Make sure that a washing programme that ends with water in tub, has been selected. 35 Make sure that the washing programme is finished. Set the drain or the spin programme if there is water in the drum. Make sure that the appliance receives electrical power. This problem may be caused by a failure of the appliance. Contact the Authorised Service Centre. If you need to open the door, please read carefully «Emergency door opening».
www.aeg.com 13.3 Emergency door opening To open the door, proceed as follows: In case of power failure or functioning failure the appliance door remains locked. The washing programme continues when the power is restored. If the door remains locked in case of failure, it is possible to open it using the emergency unlock function. 1. Press the AAN /UIT button to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4.
ENGLISH Programmes Load (kg) Energy Water Approxi- Remainconsump- consump- mate pro- ing moistion (kWh) tion (litre) gramme ture (%)1) duration (minutes) Katoen - Blanc/Couleurs 40°C 9 1.25 80 200 44 Synthetica - Synthétiques 40°C 4 0.78 55 130 35 Fijne Was - Délicats 40°C 4 0.60 63 91 35 1.5 0.35 57 60 30 Standard 60°C cotton 9 0.814 54 291 44 Standard 60°C cotton 4.5 0.56 42 259 44 Standard 40°C cotton 4.5 0.
www.aeg.com Energy Efficiency Class Spin Speed A+++ Maximum 1600 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 16. ACCESSORIES 16.1 Available in www.aeg.com/shop or from authorised dealer washing machine at www.registeraeg.com to receive information when it will be possible to enable the connectivity functionality. Only appropriate accessories approved by AEG ensure the safety standards of the appliance. If unapproved parts are used, any claims will be invalidated. 16.
ENGLISH 39
132960400-A-142016 www.aeg.