L7FEE68SC USER MANUAL EN User Manual Washing Machine
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................4 3. INSTALLATION............................................................................................................5 4. PRODUCT DESCRIPTION.........................................................................................10 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • • The operating water pressure at the water entry point from the outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar (0.8 MPa). The ventilation opening in the base must not be covered by a carpet, mat, or any floor covering. The appliance must be connected to the water mains using the new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre. Old hose sets must not be reused.
ENGLISH 2.2 Electrical connection • The appliance must be earthed. • Always use a correctly installed shockproof socket. • Make sure that the parameters on the rating plate are compatible with the electrical ratings of the mains power supply. • Do not use multi-plug adapters and extension cables. • Make sure not to cause damage to the mains plug and to the mains cable. Should the mains cable need to be replaced, this must be carried out by our Authorised Service Centre.
www.aeg.com 3.1 Unpacking WARNING! Remove all the packaging and the transit bolts before installing the appliance. WARNING! Use the gloves. 1. Remove the external film. If necessary, use a cutter. 5. Carefully put down the appliance with the rear side on it. 6. Put the front polystyrene packaging element on the floor under the appliance. Make sure not to damage the hoses. 2. Remove the cardboard top and the polystyrene packaging materials. 7. Remove the polystyrene protection from the bottom. 3.
ENGLISH 9. Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliance in factory. We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.2 Positioning and levelling 1. Install the appliance on a flat hard floor. Make sure that carpets do not stop the air circulation below the appliance.
www.aeg.com 4. Connect the water inlet hose to the cold water tap with 3/4" thread. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. When the machine is installed on a plinth or if a washer dryer is stacked on the washing machine, use the accessories described in chapter 'Accessories'. Read carefully the instructions supplied with the appliance and with the accessory.
ENGLISH 9 You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. It is possible to connect the drain hose in different ways: 1. Make a U shape with the drain hose and put it around the plastic hose guide. 2. On the edge of a sink - Fasten the guide to the water tap or to the wall. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm min. 1.
www.aeg.com 6. Position the hose directly to a builtin drain pipe in the room wall and tighten it with a clamp. 4. PRODUCT DESCRIPTION 4.1 Special features Your new washing machine meets all modern requirements for an effective treatment of laundry with low water, energy and detergent consumption and respectful of fabric care. • The ProSense technology detects the laundry load size defining the programme duration in 30 seconds.
ENGLISH 5 6 7 8 9 Rating plate Drain pump filter Feet for levelling the appliance Drain hose Inlet hose connection 11 10 Mains cable 11 Transit bolts 12 Hose support 5. CONTROL PANEL 5.1 Control panel description 3 2 1 Program Eco Bavlna Syntetické Jemné Vlna/Hedvábí Pára Antialergický 20 min.
www.aeg.com 5.2 Display Maximum load indicator. The indicator flashes during the laundry load estimation (refer to ProSense load detection paragraph) . Maximum laundry indicator. It blinks if the laundry amount exceeds the declared load. Door locked indicator. Delay start indicator. The digital indicator can show: • Programme duration (e. g. • Delay time (e. g. or ). ). • Cycle end ( ). • Warning code (e.g. ). Washing phase indicator. It flashes during pre-wash and wash phase.
ENGLISH 13 Spin speed indicator. Rinse hold indicator. Extra Silent indicator. Temperature indicator. The set. indicator appears when a cold wash is 6. DIAL AND BUTTONS 6.1 On/Off When the display shows the indicators Pressing this button for a few seconds allows to activate or deactivate the appliance. Two different tunes sound while switching the appliance on or off. and , the appliance does not heat the water.
www.aeg.com turns regularly to reduce creasing. You must drain the water to unlock the door. As the programme is very quiet, it is suitable for use at night time when cheaper electricity tariffs are available. In some programmes the rinses are performed with more water. If you touch the Start/Pauza button, the appliance performs the only draining phase. The appliance empties the water out automatically after 18 hours approximately. • Pouze vypouštění option (Skipping the wash, rinse and spin phases) .
ENGLISH the selected delay time and the appliance begins the countdown. The display shows the indicator • Extra máchání option This option adds a few rinses according to the selected washing programme. Use this option for persons allergic to detergent residues and in areas where the water is soft. This option increases slightly the programme duration. • Skipping wash phase - Pouze máchání option The appliance performs only the rinsing phase, the spinning and the draining phases of the selected programme.
www.aeg.com Programme Bavlna Programme description White cotton and coloured cotton. Normal, heavy and light soil. Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, the programme Bavlna at 60 °C and the programme Bavlna at 40 °C with the option are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton programme».
ENGLISH Programme 17 Programme description Cotton and synthetic items lightly soiled or once worn. 20 min. - 3 kg Outdoor Do not use fabric softener and make sure that there is no softener residue in the detergent dispenser. Outdoor clothing, technical, sport fabrics, waterproof and breathable jackets, shell jackets with a removable fleece or inner insulation. The recommended laundry load is 2.5 kg.
www.aeg.com Programme Default tempera- Maximum spin speed Maximum load ture Spin speed range Temperature range Syntetické 40 °C 60 °C - Cold 1200 rpm 1200 rpm - 400 rpm 3 kg Jemné 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 3 kg Vlna/Hedvábí 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 1.5 kg Steam programme - Pára - 1.5 kg Washing programmes 60 °C 1600 rpm 1600 rpm - 400 rpm 8 kg 20 min.
ENGLISH 19 Jemné Antialergický 20 min.
www.aeg.com 7.2 Woolmark Apparel Care - Blue The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of wool garments labelled as «hand wash» provided that the garments are washed according to the instructions issued by the manufacturer of this washing machine. Follow the garment care label for drying and other laundry instructions. M1623 The Woolmark symbol is a Certification mark in many countries. 8. SETTINGS 8.
ENGLISH This option increases slightly the programme duration. To activate/deactivate this option touch the Teplota button and the 21 Odstřeďování button simultaneously until indicator comes on/goes off the above the indicator. 9. BEFORE FIRST USE 1. Make sure that all transit bolts have been removed from the appliance. 2. Make sure that the electrical power is available and the water tap is open. 3. Pour 2 litres of water into the detergent compartment marked by 5.
www.aeg.com 10.3 Filling the detergent and additives 1 2 3. To use powder detergent, turn the flap up. Compartment for prewash phase, soak programme or stain remover. Compartment for washing phase. Compartment for liquid additives (fabric conditioner, starch). Maximum level for quantity of liquid additives. Flap for powder or liquid detergent.
ENGLISH With the flap in the position DOWN: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid detergent than the limit shown on the flap. • Do not set the prewash phase. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser. 23 In case a selection is not possible, no indicator comes on and an acoustic signal sounds. 10.6 Starting a programme Touch the Start/Pauza button to start the programme.
www.aeg.com Changing the delay start after the countdown has started this case, it will be not possible to guarantee the best washing results. About 20 minutes after the programme start, the programme duration could be adjusted again depending on the capacity of water absorption of the fabrics. To change the delay start: 1. Touch the Start/Pauza button to pause the appliance. The related indicator flashes. 2. Touch the Odložený start button repeatedly until the display shows the desired delay time.
ENGLISH The washing programme continues. 10.13 End of the programme 10.11 Cancelling a running programme When the programme has finished, the appliance stops automatically. The acoustic signals operate (if they are active). 1. Press the button On/Off to cancel the programme and to deactivate the appliance. 2. Press the button On/Off again to activate the appliance. Now, you can set a new washing programme.
www.aeg.com 1. If necessary, touch the Odstřeďování button to decrease the spin speed proposed by the appliance. 2. Touch the Start/Pauza button: • If you have set , the appliance drains the water and spins. • If you have set , the appliance only drains the water. The option indicator or goes out, while the indicator flashes and then goes off. 3. When the programme is completed and the door locked indicator goes off, you can open the door. 4.
ENGLISH 11.2 Stubborn stains • Use the recommended detergents for the type and colour of the fabric, the programme temperature and the level of soil. For some stains, water and detergent is not sufficient. We recommend that you pre-treat these stains before you put the items in the appliance. Special stain removers are available. Use the special stain remover that is applicable to the type of stain and fabric. 11.
www.aeg.com The regular detergents already contain water softening agents, but we recommend to run a cycle with empty drum and a descaling product occasionally. Always follow the instructions that you find on the packaging of the product. 12.3 Maintenance wash The repeated and prolonged use of low temperature programmes can cause detergent deposits, fluff residues, bacterial growth inside the drum and the tub. This could generate bad odours and mildew.
ENGLISH 29 WARNING! • Do not remove the filter while the appliance operates. • Do not clean the pump if the water in the appliance is hot. Wait until the water cools down Proceed as follows to clean the pump: 4. Insert the detergent drawer into the guide rails and close it. Run the rinsing programme without any clothes in the drum. 1. Open the pump cover. 2 1 12.7 Cleaning the drain pump WARNING! Disconnect the mains plug from the mains socket. 2.
www.aeg.com 5. When the bowl is full of water, turn the filter back and empty the container. 6. Repeat the steps 4 and 5 until the water stops to flow out. 7. Turn the filter anti-clockwise to remove it. 11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 2 1 12. Close the pump cover. 1 2 8. If it is necessary, remove fluff and objects from the filter recess. 9.
ENGLISH 31 12.8 Cleaning the inlet hose and the valve filter It is recommended to clean both the filters of the inlet hose and valve occasionally to remove any deposit, collected over the time: 1. Remove the inlet hose from the tap and clean the filter. 45° 20° 1 12.9 Emergency drain 2 3 2. Remove the inlet hose from the appliance by loosening the ring nut. If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain filter' paragraph.
www.aeg.com 13. TROUBLESHOOTING WARNING! Refer to Safety chapters. 13.1 Introduction The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre. In case of major problems, the acoustic signals operate, the display shows an alarm code and the Start/Pauza button may flash continuously: • - The appliance does not fill with water properly.
ENGLISH Problem The appliance does not fill with water properly. 33 Possible solution • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the inlet hose has no kinks, damages or bends. • Make sure that the connection of the water inlet hose is correct.
www.aeg.com Problem Possible solution The appliance makes an unusual noise and vibrates. • Make sure the levelling of the appliance is correct. Refer to "Installation instruction". • Make sure that the packaging and/or the transit bolts are removed. Refer to "Installation instruction". • Add more laundry in the drum. The load may be too small.
ENGLISH 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4. Pull twice the emergency unlock trigger downward and open the appliance door. 35 5. Take out the laundry and then close the appliance door. 6. Close the filter flap. 14. CONSUMPTION VALUES Stated values are obtained in laboratory conditions with relevant standards. Different causes can change the data: the quantity and type of laundry and ambient temperature.
www.aeg.com Programmes Load (kg) Energy Water Approxi- Remainconsump- consump- mate pro- ing moistion (kWh) tion (litre) gramme ture (%)1) duration (minutes) Standard 60°C cotton 8 0.68 54 228 44 Standard 60°C cotton 4 0.49 41 227 44 Standard 40°C cotton 4 0.46 42 228 44 1) At the end of spin phase. Off Mode (W) 0.30 Left On Mode (W) 0.30 The information given in the chart above is compliant with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC . 15.
ENGLISH 37 16. ACCESSORIES 16.1 Available in www.aeg.com/shop or from authorised dealer Only appropriate accessories approved by AEG ensure the safety standards of the appliance. If unapproved parts are used, any claims will be invalidated. The tumble dryer can be stacked on the top of the washing machine only by using the correct stacking kit manufactured and approved by AEG. Verify the compatible stacking kit by checking the depth of your appliances.
www.aeg.
ENGLISH 39
157001233-A-442017 www.aeg.