L7FEE84W USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................4 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 10 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com 1.2 Allgemeine Sicherheit • • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Überschreiten Sie nicht die maximale Beladungsmenge von 8 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • • • • • • • • • verriegeln und dadurch interne Schäden zu vermeiden. Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk. Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. Halten Sie sich an die mitgelieferte Montageanleitung. Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist.
www.aeg.com Substanzen verschmutzt sind. Die Gummiteile der Waschmaschine könnten beschädigt werden. Waschen Sie solche Textilien mit der Hand vor, bevor Sie sie in die Waschmaschine geben. • Berühren Sie während des Ablaufs eines Programms nicht die Glastür. Das Glas kann sehr heiß werden. 2.5 Service • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung.
DEUTSCH 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. Aus dem Ablaufschlauch könnte Wasser austreten. Dies ist auf den Gerätetest mit Wasser im Werk zurückzuführen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 10.
www.aeg.com Das Gerät muss einen waagerechten und festen Stand haben. Durch eine korrekte waagrechte Ausrichtung des Geräts werden Vibrationen, Geräusche und ein Wandern des Geräts während des Betriebs vermieden. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren. 3.2 Aufstellen und Ausrichten 1. Stellen Sie das Gerät auf einen ebenen, festen Boden. Stellen Sie sicher, dass die Luftzirkulation unter dem Gerät nicht durch Teppiche beeinträchtigt wird.
DEUTSCH Sie können den Ablaufschlauch auf maximal 400 cm verlängern. Fragen Sie beim autorisierten Kundendienst nach einem anderen Ablaufschlauch und der Schlauchverlängerung. VORSICHT! Achten Sie darauf, dass die Anschlüsse dicht sind. Der Ablaufschlauch kann auf unterschiedliche Weise angeschlossen werden: 1. Formen Sie den Ablaufschlauch zu einem U und verlegen Sie ihn in der Kunststoffführung. Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist.
www.aeg.com Ablaufrohr. Orientieren Sie sich an der Abbildung. Das Ende des Ablaufschlauchs muss stets belüftet sein, d. h. der Innendurchmesser des Ablaufrohrs (min. 38 mm min. 1,5") muss größer sein als der Außendurchmesser des Ablaufschlauchs. 4. Sieht das Ende des Ablaufschlauchs wie in der Abbildung gezeigt aus, können Sie es direkt in das Standrohr drücken. 5. Ohne Kunststoffführung in einen Siphon - Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle.
DEUTSCH • Dank der Option Soft Plus wird der Weichspüler gleichmäßig in der Wäsche verteilt, sodass er die Fasern durchdringt und für perfekte Weichheit sorgt. 4.
www.aeg.com 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 Programma/Programme Eco Katoen Blanc/Couleurs Synthetica Synthétiques Fijne Was Délicats 4 Tijd Besparen Gain de temps Wol/Zijde Laine/Soie Stoom Vapeur Anti-Allergie Anti-Allergies Temp.
DEUTSCH 13 5.2 Display Anzeige der max. Beladung. Die Anzeige blinkt während der Messung der Wäschemenge (siehe Abschnitt ProSense Beladungserkennung). Anzeige des max. zulässigen Wäschegewichts. Sie blinkt, wenn die Beladung das für das eingestellte Programm angegebene Gewicht überschreitet. Türverriegelungsanzeige. Zeitvorwahlanzeige. Die Digitalanzeige zeigt Folgendes an: • Programmdauer (z.B. • Zeitvorwahl (z.B. ). oder ). • Programmende ( ). • Fehlercode (z. B. ). Kontrolllampe Hauptspülgang.
www.aeg.com Zeitsparanzeige. Schleuderdrehzahlanzeige. Spülstoppanzeige. Anzeige Extra Leise. Temperaturanzeige. Die Anzeige mit kaltem Wasser gewählt wurde. erscheint, wenn ein Waschgang 6. PROGRAMMWAHLSCHALTER UND TASTEN 6.1 Aan /Uit - Marche/Arrêt Halten Sie diese Taste einige Sekunden lang gedrückt, um das Gerät ein- oder auszuschalten. Beim Ein- und Ausschalten ertönen zwei verschiedene Melodien.
DEUTSCH Gerät den Schleudergang aus und pumpt das Wasser ab. Das Gerät pumpt das Wasser nach etwa 18 Stunden automatisch ab. • Option Extra Leise einschalten. Der Zwischen- und Endschleudergang werden unterdrückt und das Programm endet mit Wasser in der Trommel. Hierdurch wird die Knitterbildung vermindert. Auf dem Display erscheint die Anzeige . Die Tür bleibt verriegelt. Die Trommel dreht sich regelmäßig, um Knitterfalten in der Wäsche zu vermeiden.
www.aeg.com Mit dieser Option kann sich die Programmdauer verlängern. Am Programmende erscheint eine Null im Display, die Anzeige leuchtet konstant und die Anzeige beginnt zu blinken. Die Trommel führt 30 Minuten lang sanfte Bewegungen aus, um die Wirkung des Dampfs aufrecht zu erhalten. Durch Berühren einer beliebigen Taste stoppt diese Knitterschutzbewegung und die Tür wird entriegelt. Mit einer kleineren Wäschemenge werden bessere Ergebnisse erzielt. 6.
DEUTSCH 6.11 Start/Pauze - Départ/ Pause 17 anzuhalten oder ein laufendes Programm zu unterbrechen. Berühren Sie die Taste Start/Pauze Départ/Pause, um das Gerät zu starten, 7. PROGRAMME 7.1 Programmübersicht Spülprogramme Programm Programmbeschreibung Spülprogramme Katoen - Blanc/Couleurs Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte.
www.aeg.com Programm Programmbeschreibung Dampfprogramm für Baumwolle und pflegeleichte Wäsche. Stoom - Vapeur Dampf kann verwendet werden für getrocknete2), gewaschene oder einmal getragene Wäschestücke. Dieses Programm reduziert Falten und Gerüche3) und lockert die Fasern auf. Nehmen Sie nach Ablauf des Programms die Wäsche schnell aus der Trommel. Nach einem Dampfprogramm lässt sich die Wäsche mühelos bügeln. Verwenden Sie kein Waschmittel.
DEUTSCH Programm Outdoor 19 Programmbeschreibung Verwenden Sie keinen Weichspüler, und stellen Sie sicher, dass sich keine Weichspülerrückstände in der Waschmittelschublade befinden. Pflegeleichte Sportbekleidung. Dieses Programm eignet sich zur schonenden Wäsche moderner Sportbekleidung, und kann auch für Sportkleidung wie Trainings-, Radfahr- oder Joggingkleidung und ähnlicher Bekleidung verwendet werden. Die empfohlene Beladung beträgt 2.5 kg.
www.aeg.com Programm Machine Clean Programmbeschreibung Wartungszyklus mit Heißwasser zur Reinigung und Auffrischung der Trommel und zum Entfernen von Rückständen, die Gerüche absondern können. Schalten Sie dieses Programm einmal im Monat ein, um beste Ergebnisse zu erzielen. Nehmen Sie alle Gegenstände aus der Trommel, bevor Sie das Programm einschalten. Drehen Sie in der Waschmittelschublade die Klappe im Fach für den Hauptwaschgang nach oben.
DEUTSCH Programm Standardtemperatur Temperaturbereich Maximale Schleuderdrehzahl Schleuderdrehzahlbereich Anti-Allergie - Anti-Allergies 60 °C 1400 U/min 1400 U/min – 400 U/min 8 kg 20 min. - 3 kg 30 °C 40 °C - 30 °C 1200 U/min 1200 U/min – 400 U/min 3 kg Outdoor 30 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min Jeans 40 °C 60 °C – kalt 1200 U/min 1200 U/min – 400 U/min 8 kg 60 °C 1200 U/min 1200 U/min – 400 U/min - Machine Clean 21 Maximale Beladung 2.
Vlekken - Taches1) ■ ■ ■ ■ Voorwas - Prélavage ■ ■ ■ ■ ■ Extra Spoelen - Rinçage plus ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Startuitstel - Départ différé ■ ■ ■ Plus Steam1) ■ ■ ■ ■ ■ Soft Plus ■ ■ ■ ■ ■ Nur Spülen 2) Tijd Besparen - Gain de temps 3) ■ ■ ■ ■ ■ ■ Machine Clean ■ Jeans Wol/Zijde - Laine/Soie ■ Outdoor Fijne Was - Délicats ■ Nur Schleudern 20 min.
DEUTSCH 7.2 Woolmark Apparel Care Blau Das Waschprogramm Wolle dieser Maschine wurde von der Firma 23 Woolmark auf das Waschen von Wolltextilien mit der Pflegekennzeichnung „Handwäsche“ getestet und zugelassen, vorausgesetzt, dass die Wäsche gemäß der Anleitung auf dem Kleidungsetikett und gemäß den Angaben des Maschinenherstellers gewaschen wird. Beachten Sie die Trocken- und Waschanleitung auf dem Kleidungsetikett.
www.aeg.com Sie wird bei Verwendung eines Weichspülers empfohlen. Mit dieser Option verlängert sich die Programmdauer leicht. Berühren Sie zum Ein-/Ausschalten dieser Option die Tasten Temp.°C und über TPM gleichzeitig, bis das Symbol der Anzeige leuchtet/erlischt. 9. VOR DER ERSTEN INBETRIEBNAHME 1. Stellen Sie sicher, dass alle Transportsicherungen aus dem Gerät entfernt wurden. 2. Achten Sie darauf, dass Spannung vorhanden und der Wasserhahn aufgedreht ist. 3.
DEUTSCH 10.3 Einfüllen von Wasch- und Pflegemitteln 25 1 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. Fach für Vorwasch-, Einweichwaschmittel oder Fleckentferner. Fach für die Hauptwäsche. Fach für flüssige Pflegemittel (Weichspüler, Stärke). Maximaler Füllstand für flüssige Pflegemittel. Klappe für Waschpulver oder Flüssigwaschmittel. Halten Sie sich immer an die Anweisungen auf der Verpackung der Waschmittel.
www.aeg.com Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. • Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. • Stellen Sie nicht den Vorwaschgang ein. • Stellen Sie nicht die Zeitvorwahl ein. 5. Messen Sie Waschmittel und Weichspüler ab. 6. Schließen Sie die Waschmittelschublade vorsichtig. 3. Schalten Sie bei Bedarf eine oder mehrere Optionen durch Berühren der entsprechenden Tasten ein.
DEUTSCH Pausenmodus zu schalten. Die zugehörige Anzeige blinkt. 2. Berühren Sie die Taste Startuitstel Départ différé wiederholt, bis im Display erscheint. 3. Berühren Sie die Taste Start/Pauze Départ/Pause erneut, um das Programm sofort zu starten. Ändern der Zeitvorwahl nach dem Start des Countdowns Ändern der Zeitvorwahl: 1. Berühren Sie die Taste Start/Pauze Départ/Pause, um das Gerät in den Pausenmodus zu schalten. Die zugehörige Anzeige blinkt. 2.
www.aeg.com Die Knitterschutzphase wird ausgeführt: . 10.10 Unterbrechen eines Programms und Ändern der Optionen Wenn das Programm bereits gestartet wurde, können Sie nur einige der Optionen ändern: 1. Berühren Sie die Taste Start/Pauze Départ/Pause. Die zugehörige Kontrolllampe blinkt. 2. Ändern Sie die Optionen. Die im Display angezeigten Informationen ändern sich entsprechend. 3. Berühren Sie die Taste Start/Pauze Départ/Pause erneut. Das Waschprogramm wird fortgesetzt. 10.
DEUTSCH 2. Nehmen Sie die Wäsche aus dem Gerät. 3. Vergewissern Sie sich, dass die Trommel leer ist. 4. Lassen Sie die Tür und die Waschmittelschublade einen Spaltbreit geöffnet, damit sich kein Schimmel und keine unangenehmen Gerüche bilden. 5. Schließen Sie den Wasserhahn. 10.
www.aeg.com • Halten Sie sich an die Anweisungen auf den Pflegeetiketten. • Waschen Sie weiße und bunte Wäsche nicht zusammen. • Manche farbigen Textilien können beim ersten Waschen verfärben. Wir empfehlen deshalb, sie die ersten Male separat zu waschen. • Knöpfen Sie Kopfkissen zu und schließen Sie Reißverschlüsse, Haken und Druckknöpfe. Schließen Sie Gürtel. • Leeren Sie die Taschen und stülpen Sie sie nach außen. • Wenden Sie mehrlagige Textilien, Wolle und bedruckte Wäschestücke vor dem Waschen.
DEUTSCH 11.5 Wasserhärte Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Enthärters für Waschmaschinen. In Gegenden mit weichem Wasser ist die Zugabe eines Enthärters nicht erforderlich. 31 Wenden Sie sich an Ihr örtliches Wasserversorgungsunternehmen, um die Wasserhärte in Ihrem Gebiet zu erfahren. Verwenden Sie die richtige Menge Wasserenthärter. Halten Sie sich an die Anweisungen auf der Verpackung des Produkts. 12.
www.aeg.com Für eine komplette Reinigung: 1. Reinigen Sie die Trommel mit einem Spezialreiniger für Edelstahl. Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts. 2. Starten Sie ein kurzes Programm für Baumwolle mit hoher Temperatur, leerer Trommel und etwas Waschpulver, um Rückstände auszuspülen. 12.
DEUTSCH 12.7 Reinigen der Ablaufpumpe 33 Siebs einen Lappen bereit, um austretendes Wasser aufzuwischen. WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. Reinigen Sie die Ablaufpumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht. • Das Gerät macht ein ungewöhnliches Geräusch, weil die Ablaufpumpe blockiert ist. 4.
www.aeg.com 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, ob sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst. 2 1 10. Reinigen Sie das Sieb unter fließendem Wasser. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: a. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. b.
DEUTSCH 35 „Reinigen des Ablauffilters“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 1. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. 2. Starten Sie das Programm zum Abpumpen des Wassers. 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 4.
www.aeg.com 13. FEHLERSUCHE WARNUNG! Siehe Kapitel Sicherheitshinweise. 13.1 Einführung Das Gerät startet nicht oder bleibt während des Betriebs stehen. Versuchen Sie zunächst, selbst eine Lösung für das Problem zu finden (siehe Tabelle). Tritt das Problem weiterhin auf, wenden Sie sich an den autorisierten Kundendienst.
DEUTSCH 37 13.2 Mögliche Störungen Störung Das Programm startet nicht. Mögliche Abhilfe • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. • Stellen Sie sicher, dass Start/Pauze - Départ/Pause berührt wurde. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab oder warten Sie, bis sie abgelaufen ist.
www.aeg.com Störung Mögliche Abhilfe Das Gerät schleudert nicht oder das Waschprogramm dauert länger als gewöhnlich. • Stellen Sie das Schleuderprogramm ein. • Vergewissern Sie sich, dass das Ablaufsieb nicht verstopft ist. Reinigen Sie ggf. das Sieb. Siehe „Reinigung und Pflege“. • Verteilen Sie die Wäschestücke mit der Hand neu und starten Sie die Schleuderphase erneut. Das Problem kann durch eine Unwucht verursacht worden sein. Es befindet sich Wasser auf dem Boden.
DEUTSCH 39 Störung Mögliche Abhilfe Nach dem Waschgang befinden sich Waschmittelrückstände in der Waschmittelschublade. • Stellen Sie sicher, dass sich die Klappe in der richtigen Position befindet (OBEN für Waschpulver - UNTEN für Flüssigwaschmittel). • Stellen Sie sicher, dass Sie die Waschmittelschublade gemäß den Anweisungen in dieser Bedienungsanleitung verwendet haben. Schalten Sie das Gerät nach der Überprüfung wieder ein.
www.aeg.com 14. VERBRAUCHSWERTE Die angegebenen Werte wurden unter Laborbedingungen gemäß den einschlägigen Normen gemessen. Folgende Faktoren können diese Werte verändern: Wäscheart und -menge sowie Raumtemperatur. Der Wasserdruck, die Versorgungsspannung und die Temperatur des einlaufenden Wassers können sich auch auf die Dauer des Waschprogramms auswirken. Die technischen Daten des Produkts können auf Grund von Verbesserungen ohne vorherige Ankündigung geändert werden.
DEUTSCH Aus-Zustand (W) 41 Ein-Zustand (W) Die in der Tabelle oben enthaltenen Informationen erfüllen die Verordnung (EU) 1015/2010 der Kommission zur Durchführung der Richtlinie 2009/125/EG. 15.
www.aeg.com 16.3 Bausatz Wasch-TrockenSäule WARNUNG! Stellen Sie den Wäschetrockner nicht unter die Waschmaschine. 16.4 Sockel mit Schublade Der Wäschetrockner kann nur mit dem von AEG hergestellten und genehmigten Bausatz Wasch-TrockenSäule auf der Waschmaschine montiert werden. Messen Sie die Tiefe Ihrer Geräte, um sich zu vergewissern, dass der Bausatz mit Ihren Geräten kompatibel ist. So steht Ihr Gerät höher und die Be- und Entladung wird einfacher.
DEUTSCH 43
157003152-C-412017 www.aeg.