L7FEE945R USER MANUAL EN User Manual Washing Machine
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................4 3. INSTALLATION............................................................................................................5 4. PRODUCT DESCRIPTION...........................................................................................9 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • The appliance must be connected to the water mains using the new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre. Old hose sets must not be reused. If the mains power supply cable is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an electrical hazard. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket.
ENGLISH • • • • access to the mains plug after the installation. Do not touch the mains cable or the mains plug with wet hands. Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. This appliance complies with the E.E.C. Directives. 2.3 Water connection • Do not cause damage to the water hoses.
www.aeg.com 7. Remove the polystyrene protection from the bottom. 1 3. Remove the internal film. 2 8. Pull up the appliance in vertical position. 4. Open the door and remove the polystyrene piece from the door seal and all the items from the drum. 9. Remove the three bolts by using the key supplied with the appliance. 5. Carefully put down the appliance with the rear side on it. 6. Put the front polystyrene packaging element on the floor under the appliance. Make sure not to damage the hoses. 10.
ENGLISH We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.2 Installation on suspended flooring 7 The appliance must be level and stable. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. Suspended wooden floors are particularly susceptible to vibration. To limit vibration we recommend placing a waterproof wooden panel, at least 15 mm thick, under the appliance.
www.aeg.com CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Make sure that the drain hose end is not immersed in the water. There may be a return of dirty water into the appliance. 3. To a stand pipe with vent-hole Insert the drain hose directly into a drain pipe. Refer to the illustration. 3.
ENGLISH 5. Without the plastic hose guide: Put the drain hose in the spigot and tighten it with a clip. Refer to the illustration. Make sure that the drain hose makes a loop to prevent particles going into the appliance from the sink. 9 6. Position the hose directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. 4. PRODUCT DESCRIPTION 4.
www.aeg.com 4.2 Appliance overview 1 2 9 8 3 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Worktop Detergent dispenser Control panel Door handle Rating plate Drain pump filter Feet for levelling the appliance 8 9 10 11 12 Drain hose Inlet hose connection Mains cable Transit bolts Hose support 5. CONTROL PANEL 5.1 Control panel description 3 2 1 Programme Eco Cottons Synthetics Delicates Wool / Silk Steam Anti-Allergy 20 min.
ENGLISH 1 Programme dial 2 Display 3 Eco touch button (Eco) 4 Time saving touch button (Time Save) 11 8 Delay start touch button (Delay Start) 9 Steam Plus touch button (Plus Steam) 10 Spin reduction touch button (Spin) • Rinse Hold option 5 Rinse touch button (Rinse) • Extra rinse option (Extra rinse) • Skipping wash phase - Only Rinse option (Rinse only) Start/Pause touch button (Start/ 6 Pause) 7 Stain/Prewash touch button (Stains/ Prewash) • Stain option (Stains) • Prewash option (Prewash) • Quiet
www.aeg.com Washing phase indicator. It flashes during pre-wash and wash phase. Rinsing phase indicator. It flashes during rinse phase. When the Soft Plus option is activated, the indicator appears. Spinning and draining phase indicator. It flashes during spin and drain phase. Steam phase indicator. Anti-crease phase indicator. Child safety lock indicator. Energy saving indicators. The indicator appears by selecting a programme for cotton at 40 °C or 60 °C. Time saving indicator.
ENGLISH Touch this button repeatedly until the desired temperature value appears on the display. When the display shows the indicators and , the appliance does not heat the water. 6.4 Spin When you set a programme, the appliance automatically sets the maximum spin speed allowed. Touch repeatedly this button to: • Decrease the spin speed. The display shows only the spin speeds available for the set programme. • Activate the Rinse Hold option. The final spin is not performed.
www.aeg.com This option is recommended for heavily soiled laundry, especially if containing sand, dust , mud and other solid particles. The options can increase the programme duration. 6.6 Plus Steam This option adds a steam phase followed by a short anti-crease phase at the end of the washing programme. The steam phase reduces fabric creasing and facilitates the fabric ironing. The indicator flashes on the display during steam phase. This option increases the programme duration slightly.
ENGLISH If you select the Cotton programme at 40°C or 60°C, the display shows the ; these are indicator the standard cotton programmes, the most efficient programmes in terms of combined energy and water consumption. 15 6.11 Start/Pause Touch the Start/Pause button to start, pause the appliance or interrupt a running programme. 7. PROGRAMMES 7.1 Programme Chart Washing programmes Programme Programme description Washing programmes Cottons White cotton and coloured cotton. Normal soil and light soil.
www.aeg.com Programme Programme description Steam programme for cotton and synthetic items. Steam Steam can be used for dried2), washed or worn once laundry. This programme reduce creases and odours3) and relaxes the fibres. When the programme is completed, quickly remove the laundry from the drum. After a steam programme, ironing becomes effortless. Do not use any detergent. If necessary, remove stains by washing or using localized stain removal. Steam programmes do not perform any hygienic cycle.
ENGLISH Programme Programme description Duvet Single synthetic blanket, padded clothes, duvets, down jackets and similar items. Sports Synthetic items. A cycle for outdoor sport clothes normal soiled. 17 1) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or doesn't rotate properly, but this is normal for this programme. 2) If you set a Steam programme with dried laundry, at the end of the cycle the laundry can be humid.
www.aeg.com Programme Default tempera- Maximum spin speed Maximum load ture Spin speed range Temperature range 30 °C 40 °C - Cold Sports 1200 rpm - 400 rpm xx kg 1) Washing programme. 2) Washing programme and waterproofing phase. Anti-Allergy 20 min.
ENGLISH 7.2 Woolmark Apparel Care Blue 19 Company for the washing of wool garments labelled as «hand wash» provided that the garments are washed according to the instructions issued by the manufacturer of this washing machine. Follow the garment care label for drying and other laundry instructions. M1230 In UK, Eire, Hong Kong and India the Woolmark symbol is a certification trademark. The wool wash cycle of this machine has been approved by The Woolmark 8. SETTINGS 8.
www.aeg.com 9. BEFORE FIRST USE 1. Make sure that all transit bolts have been removed from the appliance. 2. Make sure that the electrical power is available and the water tap is open. 3. Pour 2 litres of water into the detergent compartment marked by 5. Set and start a programme for cotton at the highest temperature without any laundry in the drum. This removes all possible dirt from the drum and the tub. . This action activates the drain system. 4.
ENGLISH 21 Compartment for prewash phase an soak programme. Compartment for washing phase. Compartment for liquid additives (fabric conditioner, starch). Maximum level for quantity of liquid additives. Compartment for stain remover. Flap for powder or liquid detergent. Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum indicated level ( ). This quantity will however guarantee the best washing results. 4.
www.aeg.com The drain pump can operate shortly before the appliance fills water. 10.7 Starting a programme with the delay start 1. Touch the Delay Start button repeatedly until the display shows the desired delay time. The indicator Make sure that the flap does not cause a blockage when you close the drawer. 10.5 Setting a programme 1. Turn the programme dial to select the desired washing programme. The related programme indicator comes on. The indicator of the Start/Pause button flashes.
ENGLISH 10.9 Programme phase indicators After touching the Start/Pause button, the maximum declared load indicator goes off, the indicator flashes, the ProSense starts the laundry load detection: 1. The appliance detects the load in the first 30 seconds: the indicator and the time dots flash, the drum rotates shortly. 2. At the end of the load detection, the indicator goes off and the time dots stop flashing. The programme duration will be adjusted accordingly and could increase or decrease.
www.aeg.com If the ProSense phase is already carried out and the water filling is already started, the new programme starts without repeating the ProSense phase. The water and the detergent are not drained out in order to avoid waste. The display shows the maximum duration of the programme, updating it about 20 minutes after the starting of the new programme. 10.
ENGLISH In any case, the appliance empties the water out automatically after approximately 18 hours. 10.15 Stand-by option The Stand-by function automatically deactivates the appliance to decrease the energy consumption when: • You do not use the appliance for 5 minutes before you touch the Start/ Pause button. Press the button On/Off to activate the appliance again. 25 • After 5 minutes from the end of the washing programme Press the On/Off button to activate the appliance again.
www.aeg.com types of fabric, or special ones for woollens only. • Do not mix different types of detergents. • To help the environment, do not use more than the recommended quantity of detergent. • Follow the instructions that you find on packaging of the detergents or other treatments without exceeding • If you pre-treat the stains, you can use a stain remover when you set a programme with a low temperature. • To use the correct quantity of detergent, check the water hardness of your domestic system.
ENGLISH 12.4 Door seal 27 1 2 Regularly examine the seal and remove all objects from the inner part. 12.5 Cleaning the drum Regularly examine the drum to prevent rust particles. For a complete cleaning: 1. Clean the drum with special products for stainless steel. 2. Remove the top part of the additive compartment to aid cleaning and flush it out under running warm water, to remove any traces of accumulated detergent. After cleaning, replace the top part in its position.
www.aeg.com 2 1 12.7 Cleaning the drain pump WARNING! Disconnect the mains plug from the mains socket. 2. Place a suitable bowl below the drain pump access to collect the water that flows out. 3. Squeeze the two levers and pull the drainage duct forward to open it. Regularly check the drain pump filter and make sure that it is clean. Clean the drain pump if: • The appliance does not drain the water. • The drum does not turn.
ENGLISH 29 2 1 7. Close the drainage duct and turn the filter anti-clockwise to remove it. 11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 2 2 1 1 8. If it is necessary, remove fluff and objects from the filter recess. 9. Make sure that the impeller of the pump can rotate. If it does not rotate, contact the Authorised Service Centre. 12. Close the pump access. 2 1 10.
www.aeg.com 12.8 Cleaning the inlet hose and the valve filter It is recommended to clean both the filters of the inlet hose and valve occasionally to remove any deposit, collected over the time: 1. Remove the inlet hose from the tap and clean the filter. 45° 20° 1 12.9 Emergency drain 2 3 2. Remove the inlet hose from the appliance by loosening the ring nut. If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain filter' paragraph.
ENGLISH 31 13. TROUBLESHOOTING WARNING! Refer to Safety chapters. 13.1 Introduction The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre. In case of major problems, the acoustic signals operate, the display shows an alarm code and the Start/Pause button may flash continuously: • - The appliance does not fill with water properly.
www.aeg.com Problem Possible solution The appliance does not fill with water properly. Make sure that the water tap is open. Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. Make sure that the water tap is not clogged. Make sure that the water inlet hose has no kinks, damages or bends. Make sure that the connection of the water inlet hose is correct.
ENGLISH Problem 33 Possible solution Make sure that the washing programme is finished. Set the drain or the spin programme if there is water in the drum. Make sure that the appliance receives electrical power. This problem may be caused by a failure of the appliance. Contact the Authorised Service Centre. If you need to open the door, please read carefully «Emergency door opening». The appliance makes an unusual noise and vibrates. Make sure the levelling of the appliance is correct.
www.aeg.com Before opening the door: To open the door, proceed as follows: 1. Press the On/Off button to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4. Keep the emergency unlock trigger pulled downward and, at the same time, open the appliance door. CAUTION! Risk of burns! Make sure that the water temperature is not too high and the laundry is not hot. If necessary, wait until they cool down.
ENGLISH Programmes Load (kg) 35 Energy Water Approxi- Remainconsump- consump- mate pro- ing moistion (kWh) tion (litre) gramme ture (%)1) duration (minutes) Standard cotton programmes Standard 60°C cotton 9 0.814 54 291 52 Standard 60°C cotton 4.5 0.56 42 259 52 Standard 40°C cotton 4.5 0.497 42 259 52 1) At the end of spin phase. Off Mode (W) Left On Mode (W) 0.30 0.
www.aeg.com 16. ACCESSORIES 16.1 Available in www.aeg.com/shop or from authorised dealer Verify the compatible stacking kit by checking the depth of your appliances. The stacking kit can be used only with the appliances specified in the leaflet provided with the accessory. Only appropriate accessories approved by AEG ensure the safety standards of the appliance. If unapproved parts are used, any claims will be invalidated.
ENGLISH 37
www.aeg.
ENGLISH 39
157008350-A-482016 www.aeg.
