L7WB64680 USER MANUAL DE Benutzerinformation Wasch-Trockner
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................6 3. MONTAGE................................................................................................................... 8 4. GERÄTEBESCHREIBUNG......................................................................................... 12 5.
DEUTSCH 3 Änderungen vorbehalten. 1. SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com • • • Halten Sie Kinder und Haustiere vom geöffneten Gerät fern. Falls Ihr Gerät mit einer Kindersicherung ausgestattet ist, empfehlen wir, diese einzuschalten. Kinder dürfen keine Reinigung und Wartung ohne Beaufsichtigung durchführen. 1.2 Allgemeine Sicherheit • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Das Gerät muss freistehend oder unterhalb der Küchenarbeitsfläche installiert werden, sofern die Platzverhältnisse dies zulassen.
DEUTSCH • • • • • • • • • • • 5 Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Überschreiten Sie nicht die maximale Beladungsmenge von 8 kg (siehe Kapitel „Programmübersicht“). Das Gerät muss mit den neu gelieferten Schlauch-Sets oder anderen neuen, vom autorisierten Kundendienst gelieferten Schläuchen an die Wasserversorgung angeschlossen werden. Alte Schläuche dürfen nicht wiederverwendet werden.
www.aeg.com • • • • • • Entfernen Sie alle Gegenstände aus der Wäsche, die eine Entzündungsquelle darstellen könnten, z. B. Feuerzeuge oder Streichhölzer. Wenn Sie den Waschtrockner vor dem Ende des Trockengangs anhalten müssen, entnehmen Sie bitte sofort die gesamte Wäsche und breiten Sie diese aus, damit die Restwärme abgeleitet werden kann. Während der letzten Phase (Abkühlphase) des Trockengangs wird keine Wärme zugeführt, um sicherzustellen, dass Wäschestücke nicht beschädigt werden.
DEUTSCH • Stellen Sie die Füße so ein, dass der dazu erforderliche Abstand zwischen Gerät und Bodenbelag vorhanden ist. • Überprüfen Sie den waagrechten Stand des Geräts mit einer Wasserwaage, wenn es an seinen endgültigen Platz gestellt wird. Richten Sie es gegebenenfalls mit den Schraubfüßen entsprechend aus. 2.2 Elektrischer Anschluss WARNUNG! Brand- und Stromschlaggefahr. • Das Gerät muss geerdet sein. • Schließen Sie das Gerät unbedingt an eine ordnungsgemäß installierte Schutzkontaktsteckdose an.
www.aeg.com 2.5 Entsorgung • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung. • Schneiden Sie das Netzkabel in der Nähe des Geräts ab, und entsorgen Sie es. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in der Trommel einschließen. • Entsorgen Sie das Gerät nach den lokalen Vorschriften zur Rücknahme und Entsorgung von Elektroaltgeräten (WEEE). 3. MONTAGE WARNUNG! Siehe Kapitel Sicherheitshinweise. 3.
DEUTSCH 9 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 1 2 8. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. Aus dem Ablaufschlauch könnte Wasser austreten. Dies ist auf den Gerätetest mit Wasser im Werk zurückzuführen. 10. Lösen Sie die drei Schrauben mit dem mitgelieferten Schraubenschlüssel. 11. Ziehen Sie die KunststoffAbstandshalter heraus. 12.
www.aeg.com WARNUNG! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 3.3 Wasserzulaufschlauch 1. Schließen Sie den Wasserzulaufschlauch an der Rückseite der Maschine an. 2. Drehen Sie ihn nach links oder rechts, je nach Position des Wasserhahns. 45 20 O O x4 Das Gerät muss einen waagerechten und festen Stand haben.
DEUTSCH Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist. Wenden Sie sich an den Kundendienst, um einen anderen Zulaufschlauch zu erhalten. 3.4 Aquastop-Vorrichtung Der Zulaufschlauch verfügt über eine Aquastop-Vorrichtung. Diese Vorrichtung verhindert Wasserlecks am Schlauch, die durch natürliche Alterung auftreten können. 2. Am Rande eines Beckens Befestigen Sie die Führung am Wasserhahn oder an der Wand.
www.aeg.com Das Ende des Ablaufschlauchs muss stets belüftet sein, d. h. der Innendurchmesser des Ablaufrohrs (min. 38 mm min. 1,5") muss größer sein als der Außendurchmesser des Ablaufschlauchs. 4. Sieht das Ende des Ablaufschlauchs wie in der Abbildung gezeigt aus, können Sie es direkt in das Standrohr drücken. Stellen Sie sicher, dass der Ablaufschlauch einen Bogen beschreibt, damit keine Partikel aus dem Becken in das Gerät gelangen können. 6.
DEUTSCH 1 2 3 4 5 6 7 Arbeitsplatte Waschmittelschublade Bedienfeld Türgriff Typenschild Sieb der Ablaufpumpe Füße für die Ausrichtung des Geräts 8 9 10 11 12 13 Ablaufschlauch Anschluss des Zulaufschlauchs Netzkabel Transportschrauben Schlauchhalter 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 Programme Trockenzeit Baumwolle Baumwolle Eco Pflegeleicht Feinwäsche Wolle/ Handwäsche Outdoor NonStop 60min Dampf Spülen Schleudern/ Abpumpen 4 Temp.
www.aeg.com 5.2 Display MIX Anzeige der max. Beladung. Die Anzeige sung der Wäschemenge. blinkt während der Mes- Anzeige des max. zulässigen Wäschegewichts. Blinkt, wenn das Wäschegewicht die maximal zulässige Füllmenge für das ausgewählte Programm überschreitet. Wenn Sie ein Programm bei überladener Trommel einschalten, blinkt auch am Programmende. Trockenzeitanzeige. Türverriegelungsanzeige. Die Digitalanzeige zeigt Folgendes an: • Programmdauer (z. B. • Zeitvorwahl (z. B.
DEUTSCH Temperaturanzeige. Die Anzeige mit kaltem Wasser gewählt wurde. Schleuderdrehzahlanzeige. 15 erscheint, wenn ein Waschgang – Anzeige Kein Schleudern. Bügeltrocken-Anzeige. Schranktrocken-Anzeige. Extratrocken-Anzeige. 6. PROGRAMMWAHLSCHALTER UND TASTEN 6.1 Einführung Wenn Sie eine Option über eine Tastenkombination anwählen möchten, halten Sie ihre Finger nicht nach unten. Die Sensoren unter den Tasten sind berührungsempfindlich und könnten Ihre Auswahl behindern. 6.
www.aeg.com 6.5 U./Min. Wenn Sie ein Programm auswählen, stellt das Gerät automatisch die höchste Schleuderdrehzahl ein. Drücken Sie diese Taste wiederholt, um: • Die Schleuderdrehzahl zu reduzieren. Das Display zeigt nur die Schleuderdrehzahlen an, die für das eingestellte Programm verfügbar sind. • Die Option „Kein Schleudern“ einschalten. Diese Option ist nur mit dem Programm Schleudern/Abpumpen verfügbar. Das Gerät überspringt alle Schleuderphasen und pumpt nur das Wasser ab.
DEUTSCH Das Programm Automatiktrocknen kann nicht für jede Wäscheart eingestellt werden. Es können nicht alle Trockenzeiten für verschiedene Wäschearten eingestellt werden. 6.10 Trockengrad 6.11 Waschen/Trocknen Berühren Sie diese Taste, um einen der 3 voreingestellten Trockengrade auszuwählen. Dank dieser Taste kann ein Programm folgende Komponenten enthalten: • Nur Waschen : Die Kontrolllampe Waschen leuchtet. • Waschen und Trocknen : Die Kontrolllampen Waschen und Trocknen leuchten.
www.aeg.com Programm Programmbeschreibung Verwenden Sie keinen Weichspüler, und stellen Sie sicher, dass sich keine Weichspülerrückstände in der Waschmittelschublade befinden. Outdoor Outdoorkleidung, technisches Gewebe, Sportgewebe, imprägnierte und atmungsaktive Jacken, Jacken mit herausnehmbarem Fleeceteil oder Innenwattierung. Bei der Durchführung eines Non-Stop Waschund Trockenprogramms stellt die Trockenphase auch die wasserabweisenden Eigenschaften wieder her.
DEUTSCH 19 Programm Programmbeschreibung Schleudern/Abpumpen Schleudern der Wäsche und Abpumpen des in der Trommel verbliebenen Wassers. Alle Gewebearten, außer Wollwäsche und Feinwäsche. 1) Während dieses Programms dreht sich die Trommel langsam, um einen schonenden Waschgang zu gewährleisten. Die Trommel scheint sich nicht oder nicht ordnungsgemäß zu drehen, aber dies ist normal für dieses Programm.
www.aeg.com Programm Standardtemperatur Temperaturbereich Maximale Schleuder- Maximale Beladrehzahl dung Schleuderdrehzahlbereich 1600 U/min 1600 U/min - 400 U/min Spülen 8 kg 1600 U/min Schleudern/Abpumpen 8 kg 1600 U/min - ■ Schleudern/Abpumpen ■ Spülen ■ Dampf ■ NonStop 60min ■ Outdoor Feinwäsche ■ Wolle/Handwäsche Pflegeleicht U./Min.
DEUTSCH 7.2 Woolmark Apparel Care – Blau • Das Waschprogramm Wolle dieser Maschine wurde von The Woolmark Company für das Waschen von Wolltextilien mit der Pflegekennzeichnung „Handwäsche“ zugelassen, vorausgesetzt, dass die Wäschestücke gemäß der Anleitung auf dem Kleidungsetikett und gemäß den Angaben des Maschinenherstellers gewaschen werden. M1664 • Das Programm Wolle trocknen dieses Geräts wurde von The Woolmark Company geprüft und zugelassen.
www.aeg.com Trockengrad Gewebetyp Beladung Bügeltrocken Bügeltrocken Baumwolle und Leinen (Betttücher, Tischtücher, Hemden usw.) bis zu 5 kg 1) Hinweise für Prüfinstitute Das Prüfverfahren gemäß EN 50229:2007-07 muss durch die Aufteilung der maximalen Beladung in zwei Trocknungszyklen und mit dem AUTOMATIKPROGRAMM SCHRANKTROCKEN für Baumwolle Eco durchgeführt werden. Der ERSTE Trocknungszyklus für 4 kg ist mit 2 Bettlaken, 6 Kopfkissenbezügen und Handtüchern durchzuführen.
DEUTSCH 23 8. EINSTELLUNGEN 8.1 Einführung Wenn Sie eine Option über eine Tastenkombination anwählen möchten, halten Sie ihre Finger nicht nach unten. Die Sensoren unter den Tasten sind berührungsempfindlich und könnten Ihre Auswahl behindern. 8.2 Kindersicherung Berühren Sie zum Ein-/Ausschalten der akustischen Signale die Tasten Flecken/ Vorw. und Zeitvorwahl gleichzeitig etwa 6 Sekunden lang. Sind die akustischen Signale ausgeschaltet, ertönen sie nur noch dann, wenn eine Störung vorliegt. 8.
www.aeg.com So werden alle eventuellen Verunreinigungen aus Trommel und Bottich entfernt. 10. TÄGLICHER GEBRAUCH - NUR WASCHEN WARNUNG! Siehe Kapitel Sicherheitshinweise. 10.1 Einschalten des Geräts 1. Stecken Sie den Netzstecker in die Netzsteckdose. 2. Öffnen Sie den Wasserhahn. 3. Halten Sie die Taste Ein/Aus einige Sekunden lang gedrückt, um das Gerät einzuschalten. Die Kontrolllampe der Taste Start/Pause beginnt zu blinken.
DEUTSCH A Klappe für Waschpulver oder Flüssigwaschmittel. Halten Sie sich immer an die Anweisungen auf der Verpackung der Waschmittel. Wir empfehlen Ihnen aber, die Höchstmenge ( ) nicht zu überschreiten. Diese Menge garantiert die besten Waschergebnisse. Entfernen Sie nach dem Waschgang bei Bedarf Waschmittelreste aus der Waschmittelschublade. 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. B 10.4 Überprüfen Sie die Position der Klappe 1.
www.aeg.com 10.6 Starten eines Programms Berühren Sie die Taste Start/Pause, um das Programm zu starten. Die zugehörige Kontrolllampe hört auf zu blinken und leuchtet konstant. Im Display blinkt die Anzeige der Programmphase und die Anzeige der maximalen Beladung erlischt. Das Programm startet, die Tür ist verriegelt. Auf dem Display erscheint die Anzeige Achten Sie darauf, dass die Klappe beim Schließen der Waschmittelschublade nicht blockiert. 10.5 Einstellen eines Programms 1.
DEUTSCH 1. Berühren Sie die Taste Start/Pause, um das Gerät in den Pausenmodus zu schalten. Die zugehörige Anzeige blinkt. 2. Berühren Sie die Taste Zeitvorwahl wiederholt, bis das Display die gewünschte Zeitvorwahl anzeigt. 3. Berühren Sie die Taste Start/Pause erneut, um den neuen Countdown zu starten. 10.8 ProSense Beladungserkennung Die Programmdauer im Display bezieht sich auf eine mittlere/hohe Beladung.
www.aeg.com 10.11 Abbrechen eines laufenden Programms 1. Drücken Sie die Taste Ein/Aus, um das Programm abzubrechen und das Gerät auszuschalten. 2. Drücken Sie die Taste Ein/Aus erneut, um das Gerät einzuschalten. Anschließend können Sie ein neues Waschprogramm einstellen. Wurde die ProSense-Phase bereits beendet und läuft Wasser in das Gerät ein, startet das neue Programm ohne die ProSense-Phase zu wiederholen. Um Wasser und Waschmittel nicht zu verschwenden, wird das Wasser nicht abgepumpt.
DEUTSCH Drücken Sie die Taste Ein/Aus, um das Gerät wieder einzuschalten. Im Display wird das Ende des zuletzt eingestellten Programms angezeigt. Drehen Sie den Programmwahlschalter, um ein neues Programm einzustellen. 29 Haben Sie ein Programm oder eine Option gewählt, das/die mit Wasser in der Trommel endet, schaltet die Standby-Funktion das Gerät nicht aus, um Sie daran zu erinnern, dass das Wasser abgepumpt werden muss. 11.
www.aeg.com Um ein gutes Trockenergebnis bei einem geringeren Energieverbrauch und in einer kürzeren Zeit zu erzielen, können Sie für die zu waschende und trocknende Wäsche keine zu niedrige Schleuderdrehzahl einstellen. 2. Berühren Sie die Taste Start/Pause, um das Programm zu starten. Die PROSENSE Erkennung startet. Im Display erscheint die Türverriegelungsanzeige , und die Anzeige der Programmphase beginnt zu blinken. Das Display zeigt auch die Restlaufzeit an. 11.
DEUTSCH 2. Füllen Sie die Wäsche Stück für Stück ein. 3. Drehen Sie den Programmwahlschalter auf das geeignete Trockenprogramm. 4. Tippen Sie zwei Mal auf die Taste Waschen/Trocknen, um das Waschprogramm abzuwählen und nur das Trockenprogramm auszuführen. Die Kontrolllampe Trocknen leuchtet. Die Anzeigen und erscheinen im Display.
www.aeg.com Reinigen Sie nach der Trockenphase die Trommel, die Dichtung und die Türinnenseite mit einem feuchten Tuch. 13. FLUSEN IN DER WÄSCHE Während des Wasch- und/oder Trockengangs können sich bei bestimmten Textilarten (Schwammtücher, Wolle oder Sweatshirts) Flusen ablösen. Die abgelösten Flusen können an den Wäschestücken im nächsten Programm anhaften. Dieses Problem verstärkt sich bei technischem Gewebe.
DEUTSCH Bügel-BHs, Gürtel, Strumpfhosen usw.) in einem Wäschenetz. • Eine sehr geringe Beladung kann in der Schleuderphase zu einer Unwucht und übermäßigen Vibrationen führen. Vorgehensweise: a. Unterbrechen Sie das Programm und öffnen Sie die Tür (siehe Abschnitt „Täglicher Gebrauch“). b. Verteilen Sie die Wäsche mit der Hand neu, so dass die Wäschestücke gleichmäßig verteilt sind. c. Drücken Sie die Taste Start/ Pause. Die Schleuderphase wird fortgesetzt. 14.
www.aeg.com 14.7 Für Trockner nicht geeignete Textilien Stellen Sie kein Trockenprogramm für folgende Wäschearten ein: • Synthetikvorhänge. • Kleidungsstücke mit Metalleinsätzen. • Nylonstrümpfe. • Steppdecken. • Bettdecken. • Daunen. • Anoraks. • Schlafsäcke. • Gewebe mit Resten von Haarsprays, Nagellackentferner oder ähnlichen Lösungsmitteln. • Kleidungsstücke aus Schaumgummi oder ähnlichen schwammartigen Materialien. • Trockengrad • Wäscheart • Gewicht der Beladung 14.
DEUTSCH 15.2 Entkalkung Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Entkalkers für Waschmaschinen. Prüfen Sie die Trommel regelmäßig auf Kalkablagerungen. Herkömmliche Waschmittel enthalten Wasserenthärtungsmittel, wir empfehlen dennoch gelegentlich ein Programm mit leerer Trommel und einem Entkalker durchzuführen. Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts. 15.
www.aeg.com zu beseitigen. Setzen Sie nach der Reinigung das Oberteil wieder ein. 15.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. 3. Stellen Sie sicher, dass alle Waschmittelreste an der Ober- und Unterseite der Aufnahme entfernt wurden. Reinigen Sie die Schubladenaufnahme mit einer kleinen Bürste.
DEUTSCH Siebs einen Lappen bereit, um austretendes Wasser aufzuwischen. 37 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, ob sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst. 4. Drehen Sie das Sieb um 180 Grad gegen den Uhrzeigersinn, um es zu öffnen und entfernen Sie es nicht. Lassen Sie das Wasser ablaufen. 10. Reinigen Sie das Sieb unter fließendem Wasser. 5.
www.aeg.com 2 1 Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: a. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. b. Starten Sie das Programm zum Abpumpen des Wassers. 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 15.
DEUTSCH Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 1. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. 2. Starten Sie das Programm zum Abpumpen des Wassers. 39 3. Stecken Sie die beiden Enden des Zulaufschlauchs in einen Behälter und lassen Sie das Wasser aus dem Schlauch fließen. 4. Leeren Sie die Ablaufpumpe. Siehe Notentleerungsverfahren. 5. Befestigen Sie den Zulaufschlauch wieder, wenn die Ablaufpumpe entleert ist.
www.aeg.com Das Programm wurde nicht ordnungsgemäß beendet oder der Betrieb zu früh unterbrochen. Erscheint der Fehlercode erneut, wenden Sie sich an den autorisierten Kundendienst. • – Das Aqua-Control-System ist eingeschaltet. Schalten Sie das Gerät aus und drehen Sie den Wasserhahn zu. Wenden Sie sich an einen autorisierten Kundendienst. WARNUNG! Schalten Sie das Gerät vor der Überprüfung aus. 16.2 Mögliche Störungen Störung Das Programm startet nicht.
DEUTSCH 41 Störung Mögliche Abhilfe Das Gerät pumpt das Wasser nicht ab. • Stellen Sie sicher, dass der Siphon nicht verstopft ist. • Vergewissern Sie sich, dass der Ablaufschlauch nicht geknickt oder zu stark gekrümmt ist. • Vergewissern Sie sich, dass das Ablaufsieb nicht verstopft ist. Reinigen Sie ggf. das Sieb. Siehe „Reinigung und Pflege“. • Vergewissern Sie sich, dass der Wasserablaufschlauch ordnungsgemäß angebracht ist.
www.aeg.com Störung Mögliche Abhilfe Die Programmdauer erhöht oder verringert sich während der Ausführung des Programms. • Die ProSense-Funktion passt die Programmdauer an die Wäscheart und -menge an. Siehe „ProSense Beladungserkennung“ im Kapitel „Täglicher Gebrauch“. Die Waschergebnisse sind nicht zufriedenstellend. Zu viel Schaum in der Trommel während des Waschprogramms. • Erhöhen Sie die Waschmittelmenge oder benutzen Sie ein anderes Waschmittel.
DEUTSCH VORSICHT! Verbrennungsgefahr! Achten Sie darauf, dass die Wassertemperatur nicht zu hoch und die Wäsche nicht heiß ist. Warten Sie sonst, bis Wasser und Wäsche sich abgekühlt haben. 43 Öffnen Sie die Tür folgendermaßen: 1. Schalten Sie das Gerät durch Drücken der Taste Ein/Aus aus. 2. Ziehen Sie den Netzstecker aus der Netzsteckdose. 3. Öffnen Sie die Filterklappe. 4. Ziehen Sie den Auslöser der Notfallentriegelung zweimal nach unten und öffnen Sie die Gerätetür.
www.aeg.com Programme Beladung (kg) EnergieWasserververbrauch brauch (Li(kWh) ter) Ungefähre Programmdauer (in Minuten) Pflegeleicht 40 °C 3 0.80 60 140 Feinwäsche 40 °C 3 0.60 60 120 1.5 0.30 60 75 Wolle/Handwäsche 30 °C 18.
DEUTSCH 45 20. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte. Entsorgen Sie * Geräte mit diesem Symbol nicht mit dem Hausmüll. Bringen Sie das Gerät zu Ihrer örtlichen Sammelstelle oder wenden Sie sich an Ihr Gemeindeamt.
www.aeg.
DEUTSCH 47
157009363-A-502017 www.aeg.