L7WBG841 USER MANUAL ES Manual de instrucciones Lavadora-secadora
www.aeg.com CONTENIDO 1. INFORMACIÓN SOBRE SEGURIDAD....................................................................... 3 2. INSTRUCCIONES DE SEGURIDAD............................................................................6 3. INSTALACIÓN............................................................................................................. 7 4. DESCRIPCIÓN DEL PRODUCTO............................................................................. 12 5. PANEL DE MANDOS.......................
ESPAÑOL 3 Salvo modificaciones. 1. INFORMACIÓN SOBRE SEGURIDAD Antes de instalar y utilizar el aparato, lea atentamente las instrucciones facilitadas. El fabricante no se hace responsable de lesiones o daños producidos como resultado de una instalación o un uso incorrectos: Conserve siempre estas instrucciones en lugar seguro y accesible para futuras consultas. 1.1 Seguridad de niños y personas vulnerables ADVERTENCIA! Existe riesgo de sufrir asfixia, lesiones o incapacidad permanente.
www.aeg.com • La limpieza y mantenimiento de usuario del aparato no podrán ser realizados por niños sin supervisión. 1.2 Seguridad general • • • • • • • • • • No cambie las especificaciones de este aparato. El aparato debe instalarse como producto independiente o debajo de la encimera de cocina si el espacio lo permite.
ESPAÑOL • • • • • • • • • • • • 5 El aparato debe conectarse a la toma de agua utilizando los nuevos juegos de tubos suministrados, o cualquier otro juego nuevo suministrado por el servicio técnico autorizado. No se deben reutilizar los juegos de tubos antiguos. Si el cable de alimentación eléctrica sufre algún daño, el fabricante, su servicio técnico autorizado o un profesional cualificado tendrán que cambiarlo para evitar riesgos eléctricos.
www.aeg.com • • • garantizar que las prendas queden a una temperatura que no las dañe. No utilice pulverizadores de agua a alta presión ni vapor para limpiar el aparato. Limpie el aparato con un paño húmedo. Utilice solo detergentes neutros. No utilice productos abrasivos, estropajos duros, disolventes ni objetos metálicos. Antes de proceder con cualquier operación de mantenimiento, apague el aparato y desconecte el enchufe de la red. 2. INSTRUCCIONES DE SEGURIDAD 2.
ESPAÑOL • Asegúrese de que no haya fugas de agua visibles durante y después del primer uso del aparato. 2.4 Uso del aparato ADVERTENCIA! Podrían producirse lesiones, descargas eléctricas, incendios, quemaduras o daños en el aparato. • Este aparato está diseñado exclusivamente para uso doméstico. • No coloque productos inflamables ni objetos mojados con productos inflamables dentro, cerca o encima del aparato. • No toque el cristal de la puerta mientras esté en marcha un programa.
www.aeg.com 7. Retire la protección de poliestireno de la base. 1 3. Retire la película interna. 2 8. Levante el aparato hasta la posición vertical. 4. Abra la puerta y retire la pieza de poliestireno de la junta de la puerta y todos los elementos del tambor. 9. Retire el cable de alimentación y el tubo de desagüe de los soportes de los tubos. Es posible ver agua que cae de la manguera de desagüe. Esto se debe a la prueba con agua del aparato en la fábrica. 5.
ESPAÑOL 11. Extraiga los separadores de plástico. 12. Coloque los tapones de plástico que encontrará en la bolsa del manual del usuario en los orificios. 9 x4 El aparato debe estar nivelado y estable. El ajuste correcto del nivel del aparato evita vibraciones, ruidos y el movimiento del aparato cuando está funcionando. Se recomienda guardar el embalaje y los pasadores de transporte para cualquier movimiento del aparato. 3.2 Colocación y nivelado 1.
www.aeg.com A 45 20 O O Si esto ocurre, cierre el grifo de agua y póngase en contacto con el servicio técnico para cambiar el tubo. 3.5 Desagüe Asegúrese de que la manguera de entrada no está en posición vertical. 3. Si fuera necesario, afloje la tuerca anular para ajustarla en la posición correcta. 4. Conecte el tubo de entrada de agua fría a una toma de agua fría con rosca de 3/4". El tubo de descarga debe permanecer a una altura mínima de 60 cm y máxima de 100 cm.
ESPAÑOL Asegúrese de que el extremo del tubo de desagüe no esté sumergido en el agua. Puede que vuelva agua sucia al aparato. 3. A un tubo vertical con orificio de ventilación - Introduzca directamente la manguera de descarga en un tubo. Consulte la ilustración. El extremo del tubo de descarga siempre debe estar ventilado; es decir, el diámetro interno del tubo de desagüe (mín. 38 mm mín. 1,5") debe ser mayor que el diámetro externo del tubo. 4.
www.aeg.com 4. DESCRIPCIÓN DEL PRODUCTO 4.
ESPAÑOL 13 5. PANEL DE MANDOS 5.1 Descripción del panel de control 3 2 1 Programa Tiempo/ Tempo Algod. Algod. ECO Sintéticos Delicados Lana/Lãs Outdoor NonStop 60min Vapor Aclarado / Enxag. Temp. Sec. Auto 4 Manchas Lavar Secar 5 Pré-lavado Centrif. Manchas/ Pre-Lav. QuickWash Inicio diferido Lavar + Secar Centrifugar/Drenar On/Off 12 1 Selector de programas 2 Pantalla 3 Tecla táctil de tiempo de secado (Tiempo/Tempo) 4 Tecla táctil de nivel de secado (Sec.
www.aeg.com Indicador de carga máxima. El indicador mación de la carga de la colada. parpadea durante la esti- Indicador de colada máxima. Parpadea cuando la colada supera la carga declarada máxima del programa seleccionado. Si realiza un programa con el tambor sobrecargado, programa. también parpadea al final del Indicador del tiempo de secado. Indicador de bloqueo de la puerta. El indicador digital puede mostrar: • Duración del programa (por ejemplo, vado). • Inicio diferido (p. ej.
ESPAÑOL 15 6. MANDO Y BOTONES 6.1 Introducción Al pulsar una combinación de teclas, no incline los dedos hacia abajo. Los sensores de las teclas inferiores son sensibles y pueden interferir con su elección. 6.2 On/Off Pulse la tecla durante unos segundos para encender o apagar el aparato. Se emiten dos tonos diferentes cuando se enciende o apaga el aparato.
www.aeg.com • Pré-lavado Use esta opción para añadir una fase de prelavado a 30 °C antes de la de lavado. Se recomienda usar esta opción para ropa muy sucia, especialmente si contiene arena, polvo, barro y otras partículas sólidas. Esta opción puede aumentar la duración del programa. 6.7 Inicio diferido Con esta opción puede retrasar el inicio de un programa a una hora más adecuada. Toque la tecla repetidamente para ajustar el inicio diferido que desee.
ESPAÑOL 17 7. PROGRAMAS 7.1 Tabla de programas Programa Descripción del programa Programas de lavado Algodón blanco y de color. Suciedad normal, intensa o ligera. Algod. Algod. ECO Algodón blanco y de color. Suciedad normal, intensa o ligera. Programa de ahorro de energía para prendas de algodón. Este programa a 60 ºC con 8 kg de carga es el programa de referencia para los datos introducidos en la etiqueta de energía, de conformidad con las normas EEC 92/75.
www.aeg.com Programa Descripción del programa Programas de vapor2) Vapor El vapor puede utilizarse para prendas secas, lavadas o utilizadas solo una vez. Estos programas pueden reducir las arrugas y olores y hacer que sus prendas queden más suaves. No utilice detergente. Si es necesario, elimine las manchas lavando la prenda o utilizando un producto para manchas localizadas. Los programas de vapor no llevan a cabo ningún ciclo higiénico.
ESPAÑOL Programa Temperatura predeterminada Rango de temperatura Velocidad máxima de centrifugado Rango de velocidades de centrifugado Sintéticos 40 °C 60 °C - Frío 1200 rpm 1200 rpm - 400 rpm 3 kg Delicados 40 °C 40 °C - Frío 1200 rpm 1200 rpm - 400 rpm 3 kg Lana/Lãs 40 °C 40 °C - Frío 1200 rpm 1200 rpm - 400 rpm 1.5 kg Outdoor 30 °C 40 °C - Frío 1200 rpm 1200 rpm - 400 rpm 2 kg NonStop 60min 30 °C 40 °C - 30 °C 1200 rpm 1200 rpm 1 kg 19 Carga máxima 1.
■ ■ ■ ■ Inicio diferido ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■4) Tiempo/ Tempo Sec. Auto Centrifugar/Drenar Quick Wash3) Aclarado/Enxag. Delicados ■ Vapor Sintéticos ■ Outdoor Algod. ECO ■ Aclarado/ Enxag. Extra Lana/Lãs Algod. ■ Opciones NonStop 60min www.aeg.com Programa 20 ■ ■ ■ ■ ■ ■ 1) Si ajusta también la opción Sin centrifugado, el aparato solamente desagua. 2) Esta opción no está disponible con temperaturas inferiores a 40 °C.
ESPAÑOL 21 7.3 Secado automático Nivel de secado Tipo de tejido Extra seco Para materiales de felpa Algodón y lino hasta 4 kg (albornoces, toallas de baño, etc.) Seco armario1) Para prendas que van a guardarse Carga Algodón y lino hasta 4 kg (albornoces, toallas de baño, etc.
www.aeg.com Nivel de secado Tipo de tejido Carga Velo- Duración (kg) cidad sugerida de (min) centrifugado (rpm) Seco armario Algodón y lino Para prendas que (albornoces, toallas de baño, etc.
ESPAÑOL Para desactivar/activar las señales acústicas, toque las teclas Manchas/PreLav. y Inicio diferido al mismo tiempo durante 6 segundos. Si se desactivan las señales acústicas, siguen funcionando cuando el aparato presenta una avería. 8.4 Aclarado extra permanente Con esta opción puede tener de forma permanente uno o dos aclarados extra cuando ajuste un nuevo programa. 23 • Toque simultáneamente Temp. y Centrif. una vez para añadir un aclarado extra. aparece en la pantalla.
www.aeg.com Siga siempre las instrucciones que encontrará en el envase de los productos de detergente, aunque se recomienda no superar el nivel máximo indicado ( ). Esta cantidad garantizará no obstante los mejores resultados de lavado. PRECAUCIÓN! Asegúrese de que no quedan prendas enganchadas entre la puerta y el cierre. Podría provocar fugas de agua y dañar la colada. 10.
ESPAÑOL 4. Para usar detergente líquido, gire la tapa abatible hacia abajo. B Con la tapa abatible en posición BAJADA: • No utilice detergentes líquidos gelatinosos ni espesos. • No ponga más detergente líquido que el límite mostrado en la tapa abatible. • No ajuste la fase de prelavado. • No ajuste la función de inicio diferido. 5. Dosifique el detergente y el suavizante. 6. Cierre con cuidado el dosificador de detergente. indicador de programa correspondiente.
www.aeg.com el retraso deseado. Se enciende el indicador Inicio diferido. 2. Toque la tecla Inicio/Pausa. El aparato inicia la cuenta atrás del inicio diferido. El programa se pone en marcha cuando termina la cuenta atrás. La estimación PROSENSE se inicia al final de la cuenta atrás. Cancelación del inicio diferido una vez iniciada la cuenta atrás Para cancelar el inicio diferido: 1. Toque la tecla Inicio/Pausa para poner en pausa el aparato. El indicador correspondiente parpadea. 2.
ESPAÑOL P. ej., la fase de lavado o prelavado están en marcha: . Cuando termina la fase, el indicador correspondiente deja de parpadear y permanece fijo. El indicador de la siguiente fase empieza a parpadear. P. ej., la fase de aclarado está en marcha: . Si selecciona el programa Vapor, el indicador enciende. de la fase de vapor se 10.10 Interrupción de un programa y cambio de las opciones Cuando el programa está en marcha, puede cambiar solo algunas opciones: 1. Pulse la tecla Inicio/Pausa.
www.aeg.com 2. 3. 4. 5. Cuando se vuelve a encender el aparato, la pantalla muestra el final del último programa seleccionado. Gire el selector de programas para ajustar un nuevo ciclo. Retire la colada del aparato. Asegúrese de que el tambor está totalmente vacío. Deje la puerta y el depósito de detergente ligeramente entreabiertos para evitar la formación de moho y olores desagradables. Cierre la llave de paso. • No se utiliza el aparato durante 5 minutos antes de tocar la tecla Inicio/ Pausa.
ESPAÑOL c. Extra seco: para prendas de algodón. El valor de tiempo de la pantalla es la duración de los ciclos de lavado y de secado, calculados con una carga predeterminada. Para obtener un buen secado usando menos energía en menos tiempo, el aparato no permite ajustar una velocidad de centrifugado demasiado baja con las prendas que van a lavarse y secarse. 2. Toque la tecla Inicio/Pausa para iniciar el programa. Se inicia la estimación PROSENSE.
www.aeg.com 3. Gire el selector de programas hasta el programa adecuado para secar las prendas. 4. Toque dos veces en Lavar + Secar para excluir el lavado y realizar solo el secado. Se enciende el indicador Secar. Los indicadores aparecen en la pantalla. y Al secar una colada grande, para obtener un buen resultado de secado debe asegurarse de que las prendas no están enrolladas y que se han distribuido uniformemente en el tambor. 12.2 Secado - Niveles automáticos 1. Toque la tecla Sec.
ESPAÑOL 31 13. PELUSA EN LAS PRENDAS Durante la fase de lavado y/o secado, algunos tipos de tejidos, como esponja, lana o sudaderas, pueden soltar pelusa. La pelusa podría adherirse a los tejidos en el siguiente ciclo. Este inconveniente aumenta con los tejidos técnicos. Para evitar las pelusas en la colada, le recomendamos: • No lavar tejidos oscuros tras haber lavado y secado tejidos claros (toalla de mano, lana y sudaderas) y viceversa. • Secar al aire este tipo de tejidos la primera vez que los lave.
www.aeg.com Se recomienda tratar previamente estas manchas antes de colocar las prendas en el aparato. Existen quitamanchas especiales. Utilice el quitamanchas especial adecuado al tipo de mancha y tejido. 14.3 Detergentes y otros tratamientos • Utilice solo detergentes y otros tratamientos especialmente fabricados para lavadoras: – detergente en polvo para todo tipo de prendas, salvo las delicadas.
ESPAÑOL • = El ciclo de secado es de alta temperatura • = El ciclo de secado es de baja temperatura • = La prenda no puede secarse en secadora 14.9 Duración del ciclo de secado El tiempo de secado puede variar dependiendo de: • la velocidad del último centrifugado • el nivel de secado • el tipo de prenda • el peso de la carga 14.10 Secado adicional Si las prendas siguen húmedas al final del programa, vuelva a seleccionar un ciclo de secado corto.
www.aeg.com 15.4 Junta de estanqueidad de la puerta 1 2 Examine periódicamente la junta y extraiga todos los objetos de la pieza interior. 15.5 Limpieza del tambor Examine periódicamente el tambor para evitar la formación de óxido. 2. Retire la parte superior del compartimento de aditivo para ayudar a limpiarlo y enjuáguelo con agua templada para eliminar restos de detergente acumulado. Después de limpiarlo, vuelva a colocar la parte superior en su sitio. Para una limpieza completa: 1.
ESPAÑOL 35 2 1 15.7 Limpieza de la bomba de desagüe ADVERTENCIA! Desenchufe el aparato de la toma de red. 2. Coloque un recipiente debajo de la bomba de desagüe para recoger el agua que salga. 3. Abra la descarga hacia abajo. Tenga siempre a mano un trapo para secar el agua que se derrame al extraer el filtro. Examine periódicamente el filtro de desagüe y asegúrese de que está limpio. Limpie la bomba de desagüe si: • El aparato no desagua. • El tambor no gira.
www.aeg.com 7. Gire el filtro hacia la izquierda y quítelo. 2 1 1 2 12. Cierre la tapa de la bomba. 8. Si fuera necesario, retire las pelusas y objetos del hueco del filtro. 9. Asegúrese de que el rotor de la bomba gira. Si no es así, póngase en contacto con el servicio técnico autorizado. 2 1 10. Limpie el filtro bajo el grifo de agua corriente. Cuando se desagua con el procedimiento de drenaje de emergencia, se debe activar de nuevo el sistema de desagüe: a.
ESPAÑOL 37 1 2 45° 3 20° 2. Retire la manguera de entrada del aparato aflojando la tuerca anular. 15.9 Desagüe de emergencia Si el aparato no puede desaguar, realice el mismo procedimiento descrito en el apartado "Limpieza del filtro de desagüe". Limpie la bomba si fuera necesario. Cuando se desagua con el procedimiento de drenaje de emergencia, se debe activar de nuevo el sistema de desagüe: 3. Limpie el filtro de la válvula situado en la parte posterior del aparato con un cepillo. 1.
www.aeg.com ADVERTENCIA! Asegúrese de que la temperatura es superior a 0°C antes de usar de nuevo el aparato. El fabricante no se hace responsable de los daños derivados de las bajas temperaturas. 16. SOLUCIÓN DE PROBLEMAS ADVERTENCIA! Consulte los capítulos sobre seguridad. 16.1 Introducción El aparato no se pone en marcha ni se detiene durante el funcionamiento. Primero, intente buscar una solución al problema (consulte la tabla).
ESPAÑOL 39 16.2 Posibles fallos Problema El programa no se pone en marcha. Posible solución • Asegúrese de que el enchufe esté conectado a la toma de corriente. • Asegúrese de que la puerta del aparato esté cerrada. • Asegúrese de que no hay ningún fusible dañado en la caja de fusibles. • Asegúrese de que se ha tocado Inicio/Pausa. • Si se ha ajustado el inicio diferido, cancele el ajuste o espere hasta el final de la cuenta atrás.
www.aeg.com Problema Posible solución Hay agua en el suelo. • Cerciórese de que los acoplamientos de los tubos de agua están bien apretados y de que no hay pérdidas de agua. • Compruebe que la manguera de entrada y el tubo de desagüe no están dañados. • Asegúrese de que usa el detergente adecuado y la cantidad correcta. No se puede abrir la puerta del aparato. • Asegúrese de que se ha seleccionado un programa de lavado que termine con agua en la cuba.
ESPAÑOL 41 Problema Posible solución La colada está llena de pelusas de diferente color. Las prendas que lavó en el ciclo anterior dejaron pelusas de un color diferente. • La fase de secado ayuda a eliminar algo de pelusa. • Limpie las prendas con un quitapelusas. En caso de que quede una cantidad excesiva de pelusas en el tambor, seleccione el programa especial para limpiarlo (consulte “Pelusa en las prendas” para obtener más detalles). Una vez finalizada la revisión, encienda el aparato.
www.aeg.com 17. VALORES DE CONSUMO Los valores indicados se obtienen en condiciones de laboratorio con los estándares pertinentes. Los datos pueden cambiar por varios motivos: la cantidad y tipo de colada y la temperatura ambiente. La presión de agua, el voltaje de la red y la temperatura de entrada del agua también pueden afectar a la duración del programa de lavado. Las especificaciones técnicas pueden variar sin previo aviso a fin de mejorar la calidad del producto.
ESPAÑOL Carga máxima de lavado Algodón 8 kg Carga máxima para secado Algodón Sintéticos 4 kg 3 kg Velocidad de centrifugado Máxima 1600 rpm 43 1) Conecte la manguera de entrada de agua a un grifo con rosca de 3/4'' . 19. ACCESORIOS 19.1 Disponible en www.aeg.com/shop o en su distribuidor autorizado 19.2 Kit de la placa de fijación Si instala el aparato en un zócalo, asegúrelo con las placas de fijación. Lea atentamente las instrucciones que se suministran con el accesorio.
157012283-A-502017 www.aeg.