L7WBG86W USER MANUAL DE Benutzerinformation Wasch-Trockner
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................6 3. MONTAGE................................................................................................................... 8 4. GERÄTEBESCHREIBUNG......................................................................................... 12 5.
DEUTSCH 3 Änderungen vorbehalten. 1. SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com • Kinder dürfen keine Reinigung und Wartung ohne Beaufsichtigung durchführen. 1.2 Allgemeine Sicherheit • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Das Gerät muss freistehend oder unterhalb der Küchenarbeitsfläche installiert werden, sofern die Platzverhältnisse dies zulassen.
DEUTSCH • • • • • • • • • • • • 5 Überschreiten Sie nicht die maximale Beladungsmenge von 8 kg (siehe Kapitel „Programmübersicht“). Das Gerät muss mit den neu gelieferten Schlauch-Sets oder anderen neuen, vom autorisierten Kundendienst gelieferten Schläuchen an die Wasserversorgung angeschlossen werden. Alte Schläuche dürfen nicht wiederverwendet werden.
www.aeg.com • • • • sofort die gesamte Wäsche und breiten Sie diese aus, damit die Restwärme abgeleitet werden kann. Während der letzten Phase (Abkühlphase) des Trockengangs wird keine Wärme zugeführt, um sicherzustellen, dass Wäschestücke nicht beschädigt werden. Reinigen Sie das Gerät nicht mit einem Wasser- und/ oder Dampfstrahl. Reinigen Sie das Gerät mit einem feuchten Tuch. Verwenden Sie ausschließlich Neutralreiniger.
DEUTSCH • Schließen Sie das Gerät unbedingt an eine ordnungsgemäß installierte Schutzkontaktsteckdose an. • Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. • Ziehen Sie nicht am Netzkabel, wenn Sie das Gerät von der Stromversorgung trennen möchten. Ziehen Sie stets am Netzstecker. • Fassen Sie das Netzkabel oder den Netzstecker nicht mit nassen Händen an. • Das Gerät entspricht den ECRichtlinien. 2.3 Wasseranschluss • Achten Sie darauf, die Wasserschläuche nicht zu beschädigen.
www.aeg.com 3. MONTAGE WARNUNG! Siehe Kapitel Sicherheitshinweise. 3.1 Auspacken WARNUNG! Entfernen Sie vor der Montage des Geräts alle Verpackungsmaterialien und Transportschrauben. WARNUNG! Tragen Sie Handschuhe. 4. Öffnen Sie die Tür und entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel. 1. Entfernen Sie die äußere Folie. Benutzen Sie, falls erforderlich, einen Cutter. 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6.
DEUTSCH 9 1 2 8. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 11. Ziehen Sie die KunststoffAbstandshalter heraus. 12. Setzen Sie die Kunststoffkappen, die sich im Beutel mit der Bedienungsanleitung befinden, in die Löcher ein. 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. Aus dem Ablaufschlauch könnte Wasser austreten. Dies ist auf den Gerätetest mit Wasser im Werk zurückzuführen.
www.aeg.com WARNUNG! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 3.3 Wasserzulaufschlauch 1. Schließen Sie den Wasserzulaufschlauch an der Rückseite der Maschine an. 2. Drehen Sie ihn nach links oder rechts, je nach Position des Wasserhahns. 45 20 O O x4 Das Gerät muss einen waagerechten und festen Stand haben.
DEUTSCH Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist. Wenden Sie sich an den Kundendienst, um einen anderen Zulaufschlauch zu erhalten. 3.4 Aquastop-Vorrichtung Der Zulaufschlauch verfügt über eine Aquastop-Vorrichtung. Diese Vorrichtung verhindert Wasserlecks am Schlauch, die durch natürliche Alterung auftreten können. 2. Am Rande eines Beckens Befestigen Sie die Führung am Wasserhahn oder an der Wand.
www.aeg.com Das Ende des Ablaufschlauchs muss stets belüftet sein, d. h. der Innendurchmesser des Ablaufrohrs (min. 38 mm min. 1,5") muss größer sein als der Außendurchmesser des Ablaufschlauchs. 4. Sieht das Ende des Ablaufschlauchs wie in der Abbildung gezeigt aus, können Sie es direkt in das Standrohr drücken. Stellen Sie sicher, dass der Ablaufschlauch einen Bogen beschreibt, damit keine Partikel aus dem Becken in das Gerät gelangen können. 6.
DEUTSCH 1 2 3 4 5 6 7 Arbeitsplatte Waschmittelschublade Bedienfeld Türgriff Typenschild Sieb der Ablaufpumpe Füße für die Ausrichtung des Geräts 8 9 10 11 12 13 Ablaufschlauch Anschluss des Zulaufschlauchs Netzkabel Transportschrauben Schlauchhalter 5. BEDIENFELD 5.
www.aeg.com 5.2 Display MIX Anzeige der max. Beladung. Die Anzeige sung der Wäschemenge. blinkt während der Mes- Anzeige des max. zulässigen Wäschegewichts. Blinkt, wenn das Wäschegewicht die maximal zulässige Füllmenge für das ausgewählte Programm überschreitet. Wenn Sie ein Programm bei überladener Trommel einschalten, blinkt auch am Programmende. Trockenzeitanzeige. Türverriegelungsanzeige. Die Digitalanzeige zeigt Folgendes an: • Programmdauer (z. B. • Zeitvorwahl (z. B.
DEUTSCH Temperaturanzeige. Die Anzeige mit kaltem Wasser gewählt wurde. Schleuderdrehzahlanzeige. 15 erscheint, wenn ein Waschgang – Anzeige Kein Schleudern. Bügeltrocken-Anzeige. Schranktrocken-Anzeige. Extratrocken-Anzeige. 6. PROGRAMMWAHLSCHALTER UND TASTEN 6.1 Einführung Wenn Sie eine Option über eine Tastenkombination anwählen möchten, halten Sie Ihre Finger nicht nach unten. Die Sensoren unter den Tasten sind berührungsempfindlich und könnten Ihre Auswahl behindern. 6.
www.aeg.com • Die Schleuderdrehzahl zu reduzieren. Das Display zeigt nur die Schleuderdrehzahlen an, die für das eingestellte Programm verfügbar sind. • Die Option „Kein Schleudern“ einschalten. Diese Option ist nur mit dem Programm Centrifugeren/Pompen Essorage/Vidange verfügbar. Das Gerät überspringt alle Schleuderphasen und pumpt nur das Wasser ab. Auf dem Display erscheint die Anzeige . 6.6 Vlek./Voorw. - Tache/ Prélav. Drücken Sie diese Taste mehrmals, um eine der beiden Optionen einzuschalten.
DEUTSCH Es können nicht alle Trockenzeiten für verschiedene Wäschearten eingestellt werden. 6.10 Droogtegraad - Niveau séchage Berühren Sie diese Taste, um einen der 3 voreingestellten Trockengrade auszuwählen. Im Display leuchtet die entsprechende Trockengradanzeige auf: • Bügeltrocken: Wäsche, die gebügelt werden soll • Schranktrocken: Wäsche, die in den Schrank gelegt werden soll • Extra Trocken: Wäsche, die vollständig trocken sein soll 17 6.
www.aeg.com Programm Programmbeschreibung Fijne was - Délicats Empfindliche Wäsche, wie z. B. aus Acryl, Viskose und Mischgewebe, die schonend gewaschen werden müssen. Normal verschmutzt. Waschmaschinenfeste Wolle, handwaschbare Wolle und an- Wol/Handwas - Laine/ Lavage à la main dere Gewebe mit dem „Handwäsche“-Pflegesymbol.1) Verwenden Sie keinen Weichspüler, und stellen Sie sicher, dass sich keine Weichspülerrückstände in der Waschmittelschublade befinden.
DEUTSCH Programm 19 Programmbeschreibung Dampfprogramme2) Stoom - Vapeur Dampf kann für getrocknete, gewaschene oder einmal getragene Wäsche benutzt werden. Diese Programme können Falten und Gerüche reduzieren und machen Ihre Wäsche weicher. Verwenden Sie kein Waschmittel. Entfernen Sie Flecken bei Bedarf durch Waschen oder einen an der entsprechenden Stelle angewendeten Fleckentferner. Dampfprogramme sind keine Hygieneprogramme.
www.aeg.com Programm Standardtemperatur Temperaturbereich Maximale Schleuder- Maximale Beladrehzahl dung Schleuderdrehzahlbereich 40 °C 60 °C - 40 °C 1600 U/min 1600 U/min - 400 U/min 8 kg 40 °C 60 °C – kalt 1200 U/min 1200 U/min - 400 U/min 3 kg 40 °C 40 °C – kalt 1200 U/min 1200 U/min - 400 U/min 3 kg 40 °C 40 °C – kalt 1200 U/min 1200 U/min - 400 U/min 1.
DEUTSCH 21 ■ Centrifugeren/Pompen - Essorage/Vidange ■ Spoelen - Rinçage ■ Stoom - Vapeur ■ NonStop 60min ■ Outdoor Fijne was - Délicats ■ Wol/Handwas - Laine/Lavage à la main Synthetica - Synthétiques TPM Katoen Eco - Coton Eco Optionen Katoen - Blanc/Couleurs Programm Mögliche Programmkombinationen ■ ■ Kein Schleudern Vlekken - Ta- ■1) ■ ■ ■ ■ Voorwas - Prélavage ■ ■ ■ ■ Extra Spoelen - Rinçage Plus ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ che2) Tijd
Droogtegraad - Niveau séchage Centrifugeren/Pompen - Essorage/Vidange Spoelen - Rinçage Stoom - Vapeur NonStop 60min Outdoor Wol/Handwas - Laine/Lavage à la main ■4) Fijne was - Délicats ■ Synthetica - Synthétiques Katoen Eco - Coton Eco Optionen Katoen - Blanc/Couleurs www.aeg.com Programm 22 1) Stellen Sie die Option Kein Schleudern ein, wird lediglich das Wasser aus dem Gerät gepumpt. 2) Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C.
DEUTSCH 23 7.3 Automatiktrocknen Trockengrad Gewebetyp Beladung Baumwolle und Leinen (Bademäntel, Badetücher usw.) bis zu 4 kg Extratrocken Für Frotteewaren Baumwolle und Leinen (Bademäntel, Badetücher usw.
www.aeg.com 7.4 Zeitgesteuertes Trocknen Trockengrad Gewebetyp Beladung (kg) Schleu derdrehzahl (U/ min) Vorgeschlagene Dauer (Min.
DEUTSCH 25 Tasten und der Programmwahlschalter (mit Ausnahme der Taste Aan/Uit Marche/Arrêt) sind ausgeschaltet. • Bevor Sie die Taste Start/Pauze Départ/Pause berühren: Das Gerät kann nicht starten. Das Gerät speichert die Auswahl dieser Option, wenn Sie es ausschalten. 8.4 Extra Spülen einschalten 8.3 Signaltöne erscheint im Display. • Berühren Sie die Tasten Temp. und TPM zwei Mal gleichzeitig, um zwei zusätzliche Spülgänge hinzuzufügen.
www.aeg.com Anzeigen der Phasen, aus denen das Programm besteht, und die Programmdauer an. 10.2 Einfüllen der Wäsche 1. Öffnen Sie die Tür des Geräts. 2. Schütteln Sie jedes Wäschestück leicht aus, bevor Sie es in das Gerät legen. 3. Geben Sie jedes Wäschestück einzeln in die Trommel. Achten Sie darauf, nicht zu viel Wäsche einzufüllen. 4. Drücken Sie die Tür fest zu. Fach für Vorwasch-, Einweichwaschmittel oder Fleckentferner. Fach für die Hauptwäsche.
DEUTSCH 27 A 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. B Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. • Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. • Stellen Sie nicht den Vorwaschgang ein. • Stellen Sie nicht die Zeitvorwahl ein. 5. Messen Sie Waschmittel und Weichspüler ab. 6. Schließen Sie die Waschmittelschublade vorsichtig.
www.aeg.com 10.6 Starten eines Programms Berühren Sie die Taste Start/Pauze Départ/Pause, um das Programm zu starten. Die zugehörige Kontrolllampe hört auf zu blinken und leuchtet konstant. Im Display blinkt die Anzeige der Programmphase und die Anzeige der maximalen Beladung erlischt. Das Programm startet, die Tür ist verriegelt. Auf dem Display erscheint die Anzeige . Die Ablaufpumpe kann vor dem Wassereinlauf eine kurze Zeit laufen. 10.7 Starten eines Programms mit Zeitvorwahl 1.
DEUTSCH ProSense Phase kann bis zu drei Mal wiederholt werden (siehe Punkt 1). Wichtig! Wird die Wäschemenge nicht verringert, startet das Waschprogramm trotz der Überladung. In diesem Fall können keine optimalen Waschergebnisse garantiert werden. Etwa 20 Minuten nach dem Programmstart kann die Programmdauer in Abhängigkeit von der Wasseraufnahmefähigkeit der Wäsche erneut angepasst werden. Die ProSense Erkennung wird nur bei vollständigen Waschprogrammen ausgeführt (wenn keine Phase übersprungen wird).
www.aeg.com 3. Schließen Sie die Tür und berühren Sie die Taste Start/Pauze - Départ/ Pause. Das Programm bzw. die Zeitvorwahl läuft weiter. 4. Die Tür kann geöffnet werden, wenn das Programm abgeschlossen ist. Oder aber Sie wählen das Programm Centrifugeren/Pompen - Essorage/ Vidange und drücken dann die Taste Start/Pauze - Départ/Pause. 10.13 Programmende Wenn das Programm beendet ist, schaltet sich das Gerät automatisch aus. Es ertönt ein Signalton (falls er aktiviert ist).
DEUTSCH 11.1 NON-STOP Programm – Waschen und Trocknen Nicht alle Programme sind mit der Trockenfunktion kompatibel. Das Programm NonStop 60min ist bereits ein vollständiges Waschund Trockenprogramm. Sie können ein „Non-StopProgramm“ einstellen, um die Wäsche zu waschen und zu trocknen. Gehen Sie hierzu folgendermaßen vor 1. Halten Sie die Aan/Uit - Marche/ Arrêt-Taste einige Sekunden lang gedrückt, um das Gerät einzuschalten. 2. Füllen Sie die Wäsche Stück für Stück ein. 3.
www.aeg.com Im Display erscheint die Türverriegelungsanzeige , und die Anzeige der Programmphase blinkt. Das Display zeigt auch die Restlaufzeit an. 11.4 Am Ende des Trockenprogramms • Das Gerät wird automatisch angehalten. • Es ertönt ein Signalton (falls er eingeschaltet ist). gedrückt, um das Gerät auszuschalten. Einige Minuten nach Ende des Programms schaltet die Energiesparfunktion das Gerät automatisch aus. 1. Nehmen Sie die Wäsche aus dem Gerät. 2.
DEUTSCH c. Extra Trocken: für Baumwollwäsche Im Display wird die Dauer des Trockenprogramms angezeigt. Um ein gutes Trockenergebnis bei einem geringeren Energieverbrauch und in einer kürzeren Zeit zu erzielen, können Sie für die zu waschende und trocknende Wäsche keine zu niedrige Schleuderdrehzahl einstellen. 2. Berühren Sie die Taste Start/Pauze Départ/Pause, um das Programm zu starten. Im Display erscheint die , und die Türverriegelungsanzeige Anzeige der Programmphase beginnt zu blinken.
www.aeg.com Starten Sie ein spezielles Programm, um die Flusen aus der Trommel zu entfernen: • Leeren Sie die Trommel. • Reinigen Sie die Trommel, die Dichtung und die Tür gründlich mit einem feuchten Tuch. • Wählen Sie das Programm „Spülen“. • Drücken Sie gleichzeitig die Tasten TPM und Tijd besparen - Gain de Temps, bis im Display CLE erscheint, um die Reinigungsfunktion einzuschalten. • Berühren Sie die Taste Start/Pauze Départ/Pause, um das Programm zu starten.
DEUTSCH – Flüssigwaschmittel, vorzugsweise für Programme mit niedrigen Temperaturen (max. 60 °C) für alle Gewebearten oder Wollwaschmittel. • Mischen Sie nicht verschiedene Waschmittel. • Verwenden Sie der Umwelt zuliebe nicht mehr als die empfohlene Waschmittelmenge. • Halten Sie sich an die Anweisungen auf der Verpackung der Wasch- und Pflegemittel und überschreiten Sie nicht die Höchstmenge ( ).
www.aeg.com 14.10 Zusätzlicher Trockengang Ist die Wäsche am Ende eines Trockenprogramms noch zu feucht, wählen Sie noch einen kurzen Trockengang. WARNUNG! Trocknen Sie die Wäsche nicht zu lang, um Knitterbildung und ein Einlaufen der Wäschestücke zu vermeiden. Mit der Erfahrung wird die Einstellung der Trockenzeiten leichter. Merken Sie sich die Dauer bereits durchgeführter Trockengänge. Zur Vermeidung elektrostatischer Aufladung nach dem Trocknen: 1. Verwenden Sie beim Waschen einen Weichspüler. 2.
DEUTSCH Temperatur und einer kleinen Menge Waschpulver. 37 1 15.4 Türdichtung 2 Überprüfen Sie die Türdichtung regelmäßig und entfernen Sie ggf. darin verfangene Gegenstände. 15.5 Reinigen der Trommel Überprüfen Sie regelmäßig, dass sich keine Rostpartikel in der Trommel abgesetzt haben. 2. Entfernen Sie das Oberteil des Pflegemittelfachs, um die Reinigung zu vereinfachen, und spülen Sie es mit fließendem warmen Wasser aus, um das angesammelte Waschmittel zu beseitigen.
www.aeg.com 2 1 15.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Stellen Sie einen geeigneten Behälter unter die Öffnung der Ablaufpumpe, um das abfließende Wasser aufzufangen. 3. Öffnen Sie den Schacht nach unten. Halten Sie beim Herausnehmen des Siebs einen Lappen bereit, um austretendes Wasser aufzuwischen. Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist.
DEUTSCH 6. Wiederholen Sie die Schritte 4 und 5, bis kein Wasser mehr herausfließt. 7. Drehen Sie das Sieb gegen den Uhrzeigersinn, um es zu entfernen. 39 2 1 1 2 12. Schließen Sie die Pumpenabdeckung. 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, ob sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst.
www.aeg.com 1 2 45° 3 20° 2. Lockern Sie die Ringmutter, um den Zulaufschlauch vom Gerät zu entfernen. 15.9 Notentleerung Kann das Gerät das Wasser nicht abpumpen, führen Sie den unter „Reinigen der Ablaufpumpe“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 1.
DEUTSCH 41 WARNUNG! Stellen Sie sicher, dass die Temperatur über 0 °C liegt, bevor Sie das Gerät wieder einschalten. Der Hersteller ist nicht für Schäden verantwortlich, die auf zu niedrige Temperaturen zurückzuführen sind. 16. FEHLERSUCHE Ist das Gerät überladen, nehmen Sie einige Wäschestücke aus der Trommel und/oder drücken Sie die Tür zu und berühren Sie gleichzeitig die Taste Start/Pauze - Départ/ Pause, bis die Anzeige WARNUNG! Siehe Kapitel Sicherheitshinweise. 16.
www.aeg.com zu. Wenden Sie sich an einen autorisierten Kundendienst. WARNUNG! Schalten Sie das Gerät vor der Überprüfung aus. 16.2 Mögliche Störungen Störung Das Programm startet nicht. Mögliche Abhilfe • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. • Stellen Sie sicher, dass Start/Pauze - Départ/Pause berührt wurde.
DEUTSCH 43 Störung Mögliche Abhilfe Das Gerät schleudert nicht oder das Waschprogramm dauert länger als gewöhnlich. • Stellen Sie das Schleuderprogramm ein. • Vergewissern Sie sich, dass das Ablaufsieb nicht verstopft ist. Reinigen Sie ggf. das Sieb. Siehe „Reinigung und Pflege“. • Verteilen Sie die Wäschestücke mit der Hand neu und starten Sie die Schleuderphase erneut. Das Problem kann durch eine Unwucht verursacht worden sein. Es befindet sich Wasser auf dem Boden.
www.aeg.com Störung Mögliche Abhilfe Nach dem Waschgang befinden sich Waschmittelrückstände in der Waschmittelschublade. • Stellen Sie sicher, dass sich die Klappe in der richtigen Position befindet (OBEN für Waschpulver - UNTEN für Flüssigwaschmittel). • Stellen Sie sicher, dass Sie die Waschmittelschublade gemäß den Anweisungen in dieser Bedienungsanleitung verwendet haben. Das Gerät trocknet nicht oder nicht richtig. • Drehen Sie den Wasserhahn auf.
DEUTSCH 1. Schalten Sie das Gerät durch Drücken der Taste Aan/Uit - Marche/ Arrêt aus. 2. Ziehen Sie den Netzstecker aus der Netzsteckdose. 3. Öffnen Sie die Filterklappe. 4. Ziehen Sie den Auslöser der Notfallentriegelung zweimal nach unten und öffnen Sie die Gerätetür. 5. Nehmen Sie die Wäsche heraus und schließen Sie die Gerätetür. 6. Schließen Sie die Filterklappe. 17. VERBRAUCHSWERTE Die angegebenen Werte wurden unter Laborbedingungen gemäß den einschlägigen Normen gemessen.
www.aeg.com Programme Beladung (kg) EnergieWasserververbrauch brauch (Li(kWh) ter) Ungefähre Programmdauer (in Minuten) Pflegeleicht 40 °C 3 0.80 60 140 Feinwäsche 40 °C 3 0.60 60 120 1.5 0.30 60 75 Wolle/Handwäsche 30 °C 1) „Baumwolle-Energiesparprogramm“ bei 60 °C mit einer Beladung von 8 kg ist in Übereinstimmung mit EWG 92/75 das Referenzprogramm für die auf dem Energielabel eingetragenen Werte. 18.
DEUTSCH 19.3 Sockel mit Schublade 47 So steht Ihr Gerät höher und die Be- und Entladung wird einfacher. Die Schublade kann zur Aufbewahrung von Wäsche benutzt werden, z. B. für Handtücher, Reinigungsprodukte usw. Lesen Sie die mit dem Zubehör gelieferte Gebrauchsanleitung sorgfältig durch. 20. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte.
157012401-A-342017 www.aeg.