L7WE86CBI USER MANUAL DE Benutzerinformation Wasch-Trockner
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................6 3. MONTAGE................................................................................................................... 8 4. GERÄTEBESCHREIBUNG......................................................................................... 17 5.
DEUTSCH 3 Änderungen vorbehalten. 1. SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com • • • Halten Sie Kinder und Haustiere vom geöffneten Gerät fern. Falls Ihr Gerät mit einer Kindersicherung ausgestattet ist, empfehlen wir, diese einzuschalten. Kinder dürfen keine Reinigung und Wartung ohne Beaufsichtigung durchführen. 1.2 Allgemeine Sicherheit • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Dieses Gerät ist für die Verwendung im Haushalt und ähnliche Zwecke vorgesehen, wie z. B.
DEUTSCH • • • • • • • • • • • • 5 Der Raum, in dem das Gerät aufgestellt wird, muss gut belüftet sein, damit keine Gase in den Raum zurückströmen, die von offenem Feuer oder von anderen Geräten stammen, die mit Brennstoffen arbeiten. Die Abluft darf nicht über denselben Abzug abgeleitet werden, über den der Dunstabzug von mit Gas oder sonstigen Brennstoffen betriebenen Geräten erfolgt.
www.aeg.com • • • • • • • gummibeschichtete Wäschestücke sowie Kleider oder Kissen mit Schaumgummipolstern dürfen nicht im Waschtrockner getrocknet werden. Weichspüler oder ähnliche Produkte dürfen nur entsprechend den Herstelleranweisungen benutzt werden. Entfernen Sie alle Gegenstände aus der Wäsche, die eine Entzündungsquelle darstellen könnten, z. B. Feuerzeuge oder Streichhölzer.
DEUTSCH • Bewahren Sie die Transportschrauben an einem sicheren Ort auf. Wenn das Gerät in Zukunft umgesetzt werden soll, müssen sie wieder angebracht werden, um die Trommel zu verriegeln und dadurch interne Schäden zu vermeiden. • Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk. • Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht.
www.aeg.com WARNUNG! Verletzungsgefahr sowie Risiko von Schäden am Gerät. • Setzen oder stellen Sie sich niemals auf die geöffnete Gerätetür. • Trocknen Sie keine tropfnassen Wäschestücke im Gerät. 2.5 Service • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. 2.6 Entsorgung • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung. • Schneiden Sie das Netzkabel in der Nähe des Geräts ab, und entsorgen Sie es.
DEUTSCH 1. Legen Sie die beiden Styroporteile unter dem Gerät auf den Boden. WARNUNG! Es wird dringend empfohlen diese Tätigkeit zu zweit durchzuführen. 2. Legen Sie das Gerät auf seine Rückseite. Achten Sie darauf, die Schläuche nicht zu beschädigen. 3. Entfernen Sie den Styroporschutz von der Geräteunterseite. 1 2 4. Bringen Sie das Gerät in die senkrechte Position und entfernen Sie den Styroporschutz aus dem Sockel. 1 2 5.
www.aeg.com 6. Entfernen Sie die drei Schrauben, die Schlauchhalter und KunststoffDistanzstücke mit dem mitgelieferten Schlüssel. F 7. Verschließen Sie die Löcher mit den Kunststoff-Kappen, die sich im Beutel mit der Bedienungsanleitung befinden. Setzen Sie die kleinste Kappe F in das obere Loch und die beiden größeren Kappen G in die unteren Löcher ein. G Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren. 3.4 Aufstellen und Ausrichten 1.
DEUTSCH 11 Das Gerät muss einen waagerechten und festen Stand haben. VORSICHT! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 3.5 Schlauch- und Kabelanschluss 900 mm 960 mm 1360 mm max 1000 mm max 1000 mm min. 600 mm 1230 mm 1450 mm min. 600 mm 1100 mm Wasserzulaufschlauch 1.Nehmen Sie den Zulaufschlauch aus der Trommel. 2.
www.aeg.com 45 20 O O 3. Schließen Sie den Wasserzulaufschlauch an der Rückseite der Maschine an. Drehen Sie den Zulaufschlauch nicht nach unten, sondern nach links oder rechts, je nach Position Ihres Wasserhahns. 4. Lösen Sie die Ringmutter, um ihn in die gewünschte Position zu bewegen. 5. Schließen Sie den Wasserzulaufschlauch an einen Kaltwasserhahn mit einem 3/4"Außengewinde an. WARNUNG! Achten Sie darauf, dass die Anschlüsse dicht sind. Verwenden Sie den mitgelieferten Schlauch.
DEUTSCH 13 max.600 mm An einen Siphon Stecken Sie den Ablaufschlauch in den Siphon und sichern Sie ihn mit dem mitgelieferten Kabelbinder L. Stellen Sie sicher, dass der Ablaufschlauch einen Bogen beschreibt, damit keine Partikel aus dem Becken in das Gerät gelangen können. An ein Wandrohr Direkte Einleitung in ein Abflussrohr in der Zimmerwand. Mit dem mitgelieferten Kabelbinder L befestigen. L Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
www.aeg.com Das Gerät besitzt auch ein Schwammkissen H, das sich in der Trommel befindet. Bringen Sie es oben auf dem Gerät, wie in der Abbildung gezeigt, an. Wenn Sie das Gerät unter dem Möbel ausrichten, drücken Sie das Schwammkissen nicht zusammen. Stellen Sie vor Beginn des Einbaus das Gerät in die Nähe der Nische und schließen Sie den Zulaufschlauch, den Ablaufschlauch und das Netzkabel bereits an. WARNUNG! Stellen Sie sicher, dass diese nicht geknickt oder gequetscht werden. 3.
DEUTSCH 15 Wechseln des Anschlags der Verkleidungstür Führen Sie den Wechsel des Anschlags der Verkleidungstür durch, bevor Sie das Gerät vollständig einbauen. N M Soll sich die Verkleidungstür von links nach rechts öffnen, vertauschen Sie die Position der Scharnierträger M und der Magnetplatte N und unteren Platte O. O M N Achten Sie darauf, dass sich die Platte mit dem Magneten in der oberen Position befindet.
www.aeg.com Legen Sie die Position des unteren Lochs unter Beachtung der in der Abbildung gezeigten Abmessungen und Abstände fest (449 mm). Lassen Sie die Löcher ein. 16-22 mm Ø 35 mm 449 mm 12,5 - 14 mm 22±1,5 mm 595-598 mm A Scharniere Zum Montieren der Scharniere müssen Sie zwei Löcher (Durchmesser 35 mm, Tiefe 12,5 - 14 mm je nach Tiefe der Schranktür) an der Türinnenseite bohren. Die Scharniere werden an der Tür mit den vier mitgelieferten Schrauben A angebracht.
DEUTSCH Gegenmagnet Das Gerät ist für einen Magnetverschluss voreingestellt. Für ein korrektes Schließen: 1. Positionieren Sie die Schaube C und den Gegenmagneten D auf der Magnetplatte N. Drücken Sie die Schranktür gegen die Schraube, bis sie eine Markierung hinterlässt. 2. Öffnen Sie die Schranktür und schrauben Sie den Gegenmagneten D (Stahlscheibe + Gummiring E) mit der Schraube C auf der Innenseite der Schranktür dort an, wo die Schraube eine Marke hinterlassen hat, wie im ersten Schritt beschrieben.
www.aeg.com 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 1 2 3 14 Die permanenten Optionen werden durch Gedrückthalten der entsprechenden Taste für mindestens 3 Sekunden eingestellt.
DEUTSCH 5.2 Display Temperaturbereich: Temperaturanzeige. Kaltwasseranzeige. Türverriegelungsanzeige. Kindersicherungsanzeige. Die Digitalanzeige zeigt Folgendes an: • Programmdauer (z. B. • Zeitvorwahl (z. B. , Wasch- und/oder Trockengang). ). • Programmende ( ). • Fehlercode (z. B. ). • Fehleranzeige ( ). Anzeige Zeit Sparen. Anzeige Zeitwahl. Dampfphasenanzeige. Anzeige Automatisches Trocknen: Bügeltrocken Schranktrocken Extratrocken Anzeige Hauptwaschgang Anzeige Extra Spülen.
www.aeg.com Trommelreinigungsanzeige. Dies ist eine Empfehlung die Trommel zu reinigen. Siehe Abschnitt „Reinigen der Trommel“ im Kapitel „Reinigung und Pflege“. Knitterschutzphasenanzeige. Trockenphaseanzeige. Schleuderbereich: Schleuderdrehzahlanzeige Anzeige Kein Schleudern. Die Schleuderphase ist ausgeschaltet. Spülstoppanzeige. Anzeige der maximalen Beladung (siehe Absatz „ProSense System Beladungserkennung“).
DEUTSCH • Die Schleuderdrehzahl zu reduzieren. Das Display zeigt nur die Schleuderdrehzahlen an, die für das eingestellte Programm verfügbar sind. • Zusätzliche Schleuderoptionen Kein Schleudern . Wählen Sie diese Option zum Ausschalten aller Schleudergänge. Das Gerät führt nur den Abpumpgang des gewählten Programms aus. Stellen Sie diese Option für Feinwäsche ein. Der Spülgang verbraucht bei einigen Waschprogrammen mehr Wasser. • Schalten Sie die Option Spülstopp ein.
Anzeige Empfohlen bei Verwendung eines Weichspülers. Halten Sie zum Ein-/Ausschalten dieser Option die Taste Flecken 3 Sekunden gedrückt, bis die Anzeige leuchtet/erlischt. im Display 1) Ist sie eingeschaltet, wird das Gerät auf diese Option voreingestellt, wenn Sie es ausschalten oder das Programm ändern/ zurücksetzen. Mit dieser Option verlängert sich die Programmdauer. Synthetica optimieren und die Weichheit der Wäsche zu verbessern. Katoen Eco www.aeg.
DEUTSCH 6.13 Permanenter Knitterschutz 6.15 Zeitwahl Diese Option fügt eine kurze Knitterschutzphase am Ende des Programms hinzu. Diese Phase vermindert die Knitterbildung und erleichtert das Bügeln. Halten Sie zum Ein-/Ausschalten dieser Option die Taste Trocknen 23 3 Sekunden gedrückt, bis die Anzeige im Display leuchtet/erlischt. Ist sie eingeschaltet, wird das Gerät auf diese Option voreingestellt, wenn Sie es ausschalten oder das Programm ändern/ zurücksetzen.
www.aeg.com 7. PROGRAMME 7.1 Programmübersicht Programm Standardtemperatur Temperaturbereich ReferenzMaxischleuderd- male rehzahl BelaSchleuderdung drehzahlbereich Programmbeschreibung (Beladung und Verschmutzungsgrad) Waschprogramme Katoen 40 °C 90 °C – kalt Katoen Eco1) 40 °C 60 °C - 40 °C Synthetica 40 °C 60 °C – kalt Fijne was 30 °C 40 °C – kalt Wol 40 °C 40 °C – kalt 1600 U/min 8 kg (1600 - 400 U/min) Weiße und bunte Baumwollwäsche. Normal, stark und leicht verschmutzt.
DEUTSCH Programm Standardtemperatur Temperaturbereich ReferenzMaxischleuderd- male rehzahl BelaSchleuderdung drehzahlbereich 1 kg Stoom - Centrifugeren/ Pompen Spoelen 25 Programmbeschreibung (Beladung und Verschmutzungsgrad) Baumwolle, pflegeleichte und Feinwäsche. Kurzes und sanftes Dampfprogramm zum Auffrischen selbst der empfindlichsten Kleidungsstücke, einschließlich Wäschestücke mit Pailletten, Spitze usw.
www.aeg.com Programm Standardtemperatur Temperaturbereich Machine Clean 60 °C ReferenzMaxischleuderd- male rehzahl BelaSchleuderdung drehzahlbereich 1200 U/min (1200 - 400 U/min) - Programmbeschreibung (Beladung und Verschmutzungsgrad) Wartungszyklus mit Heißwasser zur Reinigung und Auffrischung der Trommel und zum Entfernen von Rückständen, die Gerüche absondern können. Schalten Sie dieses Programm einmal im Monat ein, um beste Ergebnisse zu erzielen.
DEUTSCH Programm Standardtemperatur Temperaturbereich Outdoor 30 °C 40 °C – kalt ReferenzMaxischleuderd- male rehzahl BelaSchleuderdung drehzahlbereich 1200 U/min 2 kg (1200 - 400 U/min) 27 Programmbeschreibung (Beladung und Verschmutzungsgrad) Verwenden Sie keinen Weichspüler, und stellen Sie sicher, dass sich keine Weichspülerrückstände in der Waschmittelschublade befinden.
www.aeg.
■ NonStop 60min 29 Zeitvorwahl Zeit Sparen Flecken Vorwäsche2) 1) Schleudern Programm Kein Schleudern DEUTSCH ■ 1) Diese Option schließt die Option aus. 2) Vorwäsche und Flecken können nicht zusammen gewählt werden. 3) Stellen Sie die Option Kein Schleudern ein, wird lediglich das Wasser aus dem Gerät gepumpt. 7.
www.aeg.com Trockengrad 1) Schranktrocken2) Für Wäsche, die in den Schrank gelegt werden soll 3) Bügeltrocken Bügeltrocken Gewebetyp Beladung Baumwolle und Leinen (Bademäntel, Badetücher usw.
DEUTSCH 7.4 Zeitgesteuertes Trocknen Trockengrad Gewebetyp Beladung (kg) Extratrocken Für Frotteewaren Baumwolle und Leinen (Bademäntel, Badetücher usw.
www.aeg.com • Bei einer falschen Auswahl (3 kurze Töne) • Am Programmende (eine etwa 2 Minuten lange Tonfolge) • Bei einer Gerätestörung (eine etwa 5 Minuten lange Folge kurzer Töne) Berühren Sie zum Ein-/Ausschalten der akustischen Signale am Programmende die Tasten und 2 Sekunden lang. Im Display erscheint Ein oder Aus. Sind die akustischen Signale ausgeschaltet, ertönen sie nur noch dann, wenn eine Störung vorliegt. gleichzeitig etwa 9. VOR DER ERSTEN INBETRIEBNAHME 1.
DEUTSCH Das Waschen von Wäschestücken mit stark öligen oder fettigen Flecken kann zur Beschädigung der Gummiteile der Waschmaschine führen. 33 10.4 Überprüfen Sie die Position der WaschmittelKlappe 1. Ziehen Sie die Waschmittelschublade bis zum Anschlag heraus. 10.3 Einfüllen von Wasch- und Pflegemitteln - Fach für Vorwasch-, Einweichwaschmittel oder Fleckentferner. 2. Drücken Sie den Hebel nach unten und ziehen Sie die Schublade heraus. 3.
www.aeg.com Die zugehörige Kontrolllampe hört auf zu blinken und leuchtet konstant. Das Programm startet, die Tür ist verriegelt. Auf dem Display erscheint die Anzeige . Die Ablaufpumpe kann vor dem Wassereinlauf eine kurze Zeit laufen. Achten Sie darauf, dass die Klappe beim Schließen der Waschmittelschublade nicht blockiert. 10.7 Starten eines Programms mit Zeitvorwahl 1. Berühren Sie die Taste Zeitvorwahl 10.
DEUTSCH 2. Berühren Sie die Taste Zeitvorwahl wiederholt, bis das Display die gewünschte Zeitvorwahl anzeigt. 3. Berühren Sie die Taste Start/Pause erneut, um den neuen Countdown zu starten. 10.8 Die ProSense System Beladungserkennung Die Programmdauer im Display bezieht sich auf eine mittlere/hohe Beladung. Nach Berühren der Taste Start/Pause erlischt die Anzeige für die maximal zulässige Füllmenge und das ProSense System startet die Beladungserkennung: 1.
www.aeg.com Ist das ProSense System beendet und läuft das Wasser bereits in das Gerät ein, startet das neue Programm ohne das ProSense System zu wiederholen. Um Wasser und Waschmittel nicht zu verschwenden, wird das Wasser nicht abgepumpt. Das Display zeigt die maximale Programmdauer an, die etwa 20 Minuten nach dem Start des neuen Programms aktualisiert wird. Zusätzliche Möglichkeit das Programm abzubrechen: 1. Drehen Sie den Wahlschalter in die 10.
DEUTSCH • Die Tür bleibt verriegelt. • Sie müssen das Wasser abpumpen, um die Tür öffnen zu können: 1. Berühren Sie bei Bedarf die Taste Schleudern , um die vom Gerät vorgeschlagene Schleuderdrehzahl zu verringern. 2. Drücken Sie die Taste Start/Pause : Das Gerät pumpt das Wasser ab und schleudert. Die Optionslampe Spülstopp erlischt. Stellen Sie die Option Kein Schleudern ein, wird lediglich das Wasser aus dem Gerät gepumpt. 3.
www.aeg.com Nicht automatische Waschund Trockenprogramme In einigen Waschprogrammen können Sie Waschen und Trocknen kombinieren, um ein komplettes Wasch- und Trockenprogramm auszuführen. Gehen Sie hierzu folgendermaßen vor: 1. Halten Sie die On/Off-Taste einige Sekunden lang gedrückt, um das Gerät einzuschalten. 2. Füllen Sie die Wäsche Stück für Stück ein. 3. Füllen Sie das Waschmittel und die Pflegemittel in die entsprechenden Fächer. 4. Drehen Sie den Programmwahlschalter auf das Waschprogramm.
DEUTSCH 11.4 Am Ende des Trockenprogramms • Das Gerät wird automatisch angehalten. • Es ertönt ein Signalton (falls er eingeschaltet ist). • Im Display erscheint . • Die Kontrolllampe der Taste Start/ Pause erlischt. Das Türverriegelungssymbol erlischt. Das Gerät fährt ca. 30 Minuten oder länger mit der Knitterschutzphase fort, wenn die Option Knitterschutz eingestellt ist. Die Knitterschutzphase reduziert die Faltenbildung.
www.aeg.com c. Extratrocken: für Baumwollwäsche Im Display wird die Dauer des Trockenprogramms angezeigt. 2. Berühren Sie die Taste Start/Pause , um das Programm zu starten. Im Display erscheint die . Türverriegelungsanzeige Das Display zeigt auch die Restlaufzeit an. 12.3 Zeitgesteuertes Trocknen 1. Tippen Sie wiederholt auf die Taste Zeitwahl , um die gewünschte Zeit einzustellen (siehe Tabelle „Zeitgesteuertes Trocknen“ im Kapitel „Programme“). Die Trockengradanzeige erlischt und erscheint.
DEUTSCH • Reinigen Sie nach der Trockenphase die leere Trommel, die Dichtung und die Tür gründlich mit einem feuchten Tuch. Starten Sie ein spezielles Programm, um die Flusen aus der Trommel zu entfernen: • Leeren Sie die Trommel. • Reinigen Sie die Trommel, die Dichtung und die Tür gründlich mit einem feuchten Tuch. • Schalten Sie das Programm Machine Clean und Trocknen 41 ein, um das Anti-Flusen-Programm durchzuführen. • Berühren Sie die Taste Start/Pause , um das Programm zu starten.
www.aeg.com – Waschpulver für alle Gewebearten, ausschließlich Feinwäsche. Verwenden Sie Waschpulver mit Bleiche für Weißwäsche und zur Desinfektion der Wäsche – Flüssigwaschmittel, vorzugsweise für Programme mit niedrigen Temperaturen (max. 60 °C) für alle Gewebearten oder Wollwaschmittel. • Mischen Sie nicht verschiedene Waschmittel. • Verwenden Sie der Umwelt zuliebe nicht mehr als die empfohlene Waschmittelmenge.
DEUTSCH 14.9 Dauer des Trockengangs 14.11 Allgemeine Tipps Die Trockenzeit hängt ab von: • Drehzahl des letzten Schleudergangs • Trockengrad • Wäscheart • Gewicht der Beladung Die durchschnittlichen Trockenzeiten können Sie der Tabelle „Trockenprogramme“ entnehmen. Mit der Erfahrung wird die Einstellung der Trockenzeiten leichter. Merken Sie sich die Dauer bereits durchgeführter Trockengänge. 14.
www.aeg.com 15.4 Türmanschette mit Doppellippe Das Gerät ist mit einem selbstsreinigenden Ablaufsystem ausgestattet, so dass leichte Flusenfasern, die sich von den Kleidungsstücken lösen, mit dem Wasser ausgespült werden. So muss der Kunde bei regelmäßigen Wartungs- und Reinigungsarbeiten nicht auf diesen Bereich zugreifen. Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts.
DEUTSCH 45 4. Setzen Sie die Waschmittelschublade in die Führungsschienen ein und schließen Sie sie. Starten Sie das Spülprogramm ohne Wäsche in der Trommel. 2. Entfernen Sie das Oberteil des Pflegemittelfachs, um die Reinigung zu vereinfachen, und spülen Sie es mit fließendem warmen Wasser aus, um das angesammelte Waschmittel zu beseitigen. Setzen Sie nach der Reinigung das Oberteil wieder ein. 15.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose.
www.aeg.com Gehen Sie zum Reinigen der Pumpe folgendermaßen vor: 2 1. Öffnen Sie die Pumpenabdeckung. 1 2. Stellen Sie einen geeigneten Behälter unter die Öffnung der Ablaufpumpe, um das abfließende Wasser aufzufangen. Halten Sie beim Herausnehmen des Siebs einen Lappen bereit, um austretendes Wasser aufzuwischen. 180˚ 3. Drehen Sie das Sieb um 180 Grad gegen den Uhrzeigersinn, um es zu öffnen und entfernen Sie es nicht. Lassen Sie das Wasser ablaufen. 4.
DEUTSCH 47 6. Drehen Sie das Sieb gegen den Uhrzeigersinn, um es zu entfernen. 1 2 7. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. Prüfen Sie, ob sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst. 8. Reinigen Sie das Sieb unter fließendem Wasser. 2 1 9. Setzen Sie das Sieb wieder in die dafür vorgesehenen Führungen ein und drehen Sie es im Uhrzeigersinn.
www.aeg.com 2 10. Schließen Sie die Pumpenabdeckung. 1 Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 1. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. 2. Starten Sie das Programm zum Abpumpen des Wassers. 15.8 Reinigen des Siebs des Zulaufschlauchs und Ventils 1 2 3 45° 20° 15.9 Notentleerung Kann das Gerät das Wasser nicht abpumpen, führen Sie den unter „Reinigen der Ablaufpumpe“ beschriebenen Vorgang aus.
DEUTSCH 15.10 Frostschutzmaßnahmen Falls das Gerät in einem Bereich installiert ist, in dem die Temperatur um 0 °C erreichen oder unter 0 °C sinken kann, entfernen Sie das im Zulaufschlauch und in der Ablaufpumpe verbliebene Wasser. 49 5. Befestigen Sie den Zulaufschlauch wieder, wenn die Ablaufpumpe entleert ist. 1. Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Schließen Sie den Wasserhahn. 3.
www.aeg.com Ist das Gerät überladen, nehmen Sie einige Wäschestücke aus der Trommel und/oder drücken Sie die Tür zu und drücken Sie gleichzeitig die Taste Start/Pause Abbildung unten). , bis die Anzeige aufhört zu blinken (siehe 16.2 Mögliche Störungen Störung Mögliche Abhilfe • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat.
DEUTSCH 51 Störung Mögliche Abhilfe Das Gerät pumpt das Wasser nicht ab. • Stellen Sie sicher, dass der Siphon nicht verstopft ist. • Vergewissern Sie sich, dass der Ablaufschlauch nicht geknickt oder zu stark gekrümmt ist. • Vergewissern Sie sich, dass das Ablaufsieb nicht verstopft ist. Reinigen Sie ggf. das Sieb. Siehe „Reinigung und Pflege“. • Vergewissern Sie sich, dass der Wasserablaufschlauch ordnungsgemäß angebracht ist.
www.aeg.com Störung Mögliche Abhilfe Die Programmdauer erhöht oder verringert sich während der Ausführung des Programms. • Das ProSense System passt die Programmdauer an die Wäscheart und -menge an. Siehe „ProSense System Beladungserkennung“ im Kapitel „Täglicher Gebrauch“. Die Waschergebnisse sind nicht zufriedenstellend. Zu viel Schaum in der Trommel während des Waschprogramms. • Erhöhen Sie die Waschmittelmenge oder benutzen Sie ein anderes Waschmittel.
DEUTSCH VORSICHT! Verbrennungsgefahr! Achten Sie darauf, dass die Wassertemperatur nicht zu hoch und die Wäsche nicht heiß ist. Warten Sie sonst, bis Wasser und Wäsche sich abgekühlt haben. VORSICHT! Verletzungsgefahr! Vergewissern Sie sich, dass die Trommel sich nicht dreht. Warten Sie sonst, bis die Trommel zum Stillstand gekommen ist. Stellen Sie sicher, dass der Wasserstand in der Trommel nicht zu hoch ist.
www.aeg.com Programme Feinwäsche 40 °C Wolle/Handwäsche 30 °C Beladung (kg) EnergieWasserververbrauch brauch (Li(kWh) ter) Ungefähre Programmdauer (in Minuten) 2 0.30 47 60 1.5 0.15 58 70 1) „Baumwolle-Energiesparprogramm“ bei 60 °C mit einer Beladung von 8 kg ist in Übereinstimmung mit EG 96/60 das Referenzprogramm für die auf dem Energielabel eingetragenen Werte. 18.
DEUTSCH 55
157020710-A-322018 www.aeg.