L7WEE861R USER MANUAL EN User Manual Washer Dryer
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................6 3. INSTALLATION............................................................................................................7 4. PRODUCT DESCRIPTION.........................................................................................12 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • • • • • • • • • • This appliance is intended to be used in household and similar applications such as: – staff kitchen areas in shops, offices and other working environments; – by clients in hotels, motels, bed & breakfast and other residential type environments; – areas for communal use in blocks of flats or in launderettes. The appliance shall be installed as a freestanding product or below the kitchen worktop if space margins permit.
ENGLISH • • • • • • • • • • • • • 5 The appliance must be connected to the water mains using the new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre. Old hose sets must not be reused. If the mains power supply cable is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an electrical hazard. Wipe away lint or packaging debris that has accumulated around the appliance.
www.aeg.com • • Clean the appliance with a moist cloth. Use only neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. 2. SAFETY INSTRUCTIONS 2.1 Installation The installation must comply with relevant national regulations. • Follow the installation instructions supplied with the appliance.
ENGLISH 2.4 Use WARNING! Risk of injury, electric shock, fire, burns or damage to the appliance. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. • Do not touch the glass door while a programme is in operation. The glass can get hot. • Do not dry damaged (torn, frayed) items that contain padding or fillings. • If laundry has been washed with a stain remover, carry out an additional rinse cycle before starting a drying cycle.
www.aeg.com 7. Remove the polystyrene protection from the bottom. 1 3. Remove the internal film. 2 8. Pull up the appliance in vertical position. 4. Open the door and remove the polystyrene piece from the door seal and all the items from the drum. 9. Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliance in factory. 5. Carefully put the appliance down on its rear side. 6.
ENGLISH 2. Loosen or tighten the feet to adjust the level. WARNING! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level. 11. Pull out the plastic spacers. 12. Put the plastic caps, that you find in the user manual bag, in the holes. x4 The appliance must be level and stable. We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.
www.aeg.com 2. Position it toward left or right depending on the position of the water tap. 45 20 You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. O O It is possible to connect the drain hose in different ways: 1. Make a U shape with the drain hose and put it around the plastic hose guide. Make sure that the inlet hose is not in vertical position. 3.
ENGLISH 11 5. Without the plastic hose guide, to a sink spigot - Put the drain hose in the spigot and tighten it with a clamp. Refer to the illustration. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm min. 1.5") must be larger than the external diameter of the drain hose. 4. If the end of the drain hose looks like this (see the picture), you can push it directly into the stand pipe.
www.aeg.com 4. PRODUCT DESCRIPTION 4.
ENGLISH 13 5. CONTROL PANEL 5.1 Control panel description 3 2 1 Programme Time Drying Cottons Cottons Eco Synthetics Delicates Wool/Handwash Outdoor Anti-Allergy NonStop 60min Steam Rinse Temp. Stains Spin Prewash Spin Wash 12 5.
www.aeg.com Maximum load indicator. The icon flashes during laundry load estimation (refer to "PROSENSE load detection" paragraph). Maximum laundry indicator. It flashes when the laundry load exceeds the maximum declared load of the selected programme. If you run a programme when the drum is overloaded, end of the programme. also flashes at the Drying time indicator. Door locked indicator. The digital indicator can show: , washing and/or drying phase). • Programme duration (e. g. • Delay time (e. g.
ENGLISH 15 6. DIAL AND BUTTONS 6.1 On/Off Pressing this button for a few seconds allows to activate or deactivate the appliance. Two different tunes sound while switching the appliance on or off. As the Stand-by function automatically deactivates the appliance to decrease the energy consumption in a few cases, you may need to activate the appliance again. For more details, refer to Stand-by paragraph in Daily Use chapter. 6.
www.aeg.com This option is not available with a temperature lower than 40 °C. • Prewash Use this option to add a pre-wash phase at 30 °C before the washing phase. This option is recommended for heavily soiled laundry, especially if containing sand, dust , mud and other solid particles. The options can increase the programme duration. 6.6 Delay Start 6.8 Time Drying Touch this button to set the time that suits the fabrics you have to dry (refer to "Timed drying" table).
ENGLISH 17 7. PROGRAMMES 7.1 Programme Chart Programme Programme description Washing programmes Cottons Cottons Eco White cotton and coloured cotton. Normal, heavy and light soil. White cotton and coloured cotton. Normal, heavy and light soil. Cottons energy saving programme. This programme at 60ºC with a load of 8 kg is the reference programme for data entered in the energy label, in compliance with 96/60/EC Directive.
www.aeg.com Programme Programme description NonStop 60min Complete programme composed of a washing phase and of a drying phase for a small load of mixed fabrics (cotton and synthetic items). appears on the display. Also, the indicator Steam programme Steam programmes2) Steam Steam can be used for dried, washed or worn once laundry. These programmes can reduce creases and odours and make your laundry softer. Do not use any detergent.
ENGLISH Programme Default tempera- Reference spin ture speed Temperature Spin speed range range Maximum load Synthetics 40 °C 60 °C - Cold 1200 rpm 1200 rpm - 400 rpm 4 kg Delicates 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 4 kg Wool/Handwash 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 1.5 kg Outdoor 30 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 2.
Prewash ■ ■ ■ ■ Stains2) ■ ■ ■ ■ ■ Delay Start ■ ■ ■ ■ Quick Wash3) ■ ■ ■ ■ Time Drying ■ ■ ■ ■ Auto Drying ■ ■4) ■ ■ ■ ■ Rinse ■ ■ Steam Delicates ■ NonStop 60min Synthetics ■ Anti-Allergy Cottons Eco ■ Outdoor Cottons ■ Options Extra Rinse Wool/Handwash www.aeg.com Programme 20 ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) Before setting this option, select a suitable washing programme for the garments.
ENGLISH 7.2 Woolmark Apparel Care Blue • The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of wool garments labelled as "hand wash" provided that the products are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine. M1230 • The wool drying cycle of this machine has been tested and approved by The Woolmark Company.
www.aeg.com Dryness Level Type of fabric Load Iron Dry Suitable for ironing Cottons and Linen (sheets, tablecloths, shirts, etc) up to 6 kg 1) Hints for test institute The test performance, in accordance with EN 50229, must be carried out with a FIRST drying load of the maximum declared drying capacity (load composition according to EN61121) by setting the AUTOMATIC CUPBOARD DRY for Cottons Eco programme.
ENGLISH 23 8. BEFORE FIRST USE During installation or before first use you may observe some water in the appliance. This is a residual water left in the appliance after a full functional test in the factory to ensure the appliance is delivered to customers in perfect working order and is no cause for concern. 1. Make sure that all transit bolts have been removed from the appliance. 2. Make sure that the electrical power is available and the water tap is open. 3.
www.aeg.com 10. DAILY USE - WASHING ONLY WARNING! Refer to Safety chapters. 10.3 Filling the detergent and additives 10.1 Activating the appliance 1. Connect the mains plug to the mains socket. 2. Open the water tap. 3. Press the On/Off button for a few seconds to activate the appliance. The indicator of the Start/Pause button starts flashing. The programme dial is automatically set on Cotton programme and only the indicator Wash is on above the Mode button.
ENGLISH 1 2 3. To use powder detergent, turn the flap up. 25 With the flap in the position DOWN: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid detergent than the limit shown on the flap. • Do not set the prewash phase. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser. 4. To use liquid detergent, turn the flap down.
www.aeg.com To perform washing only, make sure that only the Wash indicator is on above the Mode button. In case a selection is not possible, no indicator comes on and an acoustic signal sounds. 10.6 Starting a programme Touch the Start/Pause button to start the programme. The related indicator stops flashing and stays on. In the display, the indicator of the operating phase starts flashing and the maximum load indicator goes off. The programme starts, the door is locked.
ENGLISH 10.11 Cancelling a running programme this case, it will be not possible to guarantee the best washing results. About 20 minutes after the programme start, the programme duration could be adjusted again depending on the capacity of water absorption of the fabrics. 1. Press the button On/Off to cancel the programme and to deactivate the appliance. 2. Press the button On/Off again to activate the appliance. Now, you can set a new washing programme.
www.aeg.com 10.13 End of the programme When the programme has finished, the appliance stops automatically. The acoustic signals operate (if they are active). In the display all washing phase indicators become steady and the time area shows . The indicator of the Start/Pause button goes off. The door unlocks and the indicator goes off. flashes at the end of the programme in case of overloaded drum. 1. Press the On/Off button to deactivate the appliance.
ENGLISH 11.1 Complete wash&dry programmes Automatic Non-Stop programme The appliance is equipped with the NonStop 60min programme, an automatic wash&dry programme where it is not necessary to set the Dry mode. To run this programme: 1. After loading laundry and detergent, press the On/Off button for some seconds to activate the appliance. 2. Set the NonStop 60min programme by means of the programme dial. The indicator appears on the display 3. Touch the Start/Pause button to start the programme.
www.aeg.com 2. Touch the Start/Pause to start the programme. The PROSENSE estimation starts. In the display the door locked indicator comes on and the indicator of the running phase starts flashing. The display also shows the remaining programme time. 11.4 At the end of the drying programme • Press the button On/Off for some seconds to deactivate the appliance. After some minutes from the end of the programme, the energy saving function deactivates the appliance automatically. 1.
ENGLISH To have a good drying by using less energy and in a shorter time, the appliance does not let you set a too low spin speed for the items to be washed and dried. 2. Touch button Start/Pause to start the programme. In the display the door locked indicator goes on, the indicator of the running phase starts flashing. The display also shows the remaining programme time. 12.3 Timed Drying 1.
www.aeg.com 14. HINTS AND TIPS WARNING! Refer to Safety chapters. 14.1 The laundry load • Divide the laundry into: white, coloured, synthetics, delicates and wool. • Follow the washing instructions on the laundry care labels. • Do not wash white and coloured items together. • Some coloured items can discolour with the first wash. We recommend that you wash them separately for the first couple of times. • Button up pillowcases, close zippers, hooks and poppers. Tie up belts. • Empty pockets and unfold.
ENGLISH 14.5 Water hardness • If the water hardness in your area is high or moderate, we recommend that you use a water softener for washing machines. In areas where the water hardness is soft it is not necessary to use a water softener. • = The drying cycle is at high temperature • = The drying cycle is at reduced temperature • = The item can not be tumble dried. To find out the water hardness in your area, contact your local water authority. Use the correct quantity of water softener.
www.aeg.com CAUTION! Do not use alcohol, solvents or chemical products. 15.4 Door seal CAUTION! Do not clean the metal surfaces with chlorine-based detergent. 15.2 Descaling If the water hardness in your area is high or moderate, we recommend that you use a water descaling product for washing machines. Regularly examine the seal and remove all objects from the inner part. 15.5 Cleaning the drum Regularly examine the drum to check for limescale. Regularly examine the drum to prevent rust forming.
ENGLISH 35 1 2 2. Remove the top part of the additive compartment to aid cleaning and flush it out under running warm water, to remove any traces of accumulated detergent. After cleaning, replace the top part in its position. 15.7 Cleaning the drain pump WARNING! Disconnect the mains plug from the mains socket. Regularly check the drain pump filter and make sure that it is clean. Clean the drain pump if: • The appliance does not drain the water. • The drum does not turn.
www.aeg.com 6. Repeat the steps 4 and 5 until the water stops to flow out. 7. Turn the filter anti-clockwise to remove it. 2 1 2. Place a suitable bowl below the drain pump access to collect the water that flows out. 3. Open the chute downwards. Always keep a rag nearby to dry up any water spillages when removing the filter. 4. Turn the filter 180 degrees in anticlockwise direction to open it, without removing. Let the water flow out. 5.
ENGLISH 2 37 1 2 1 3 2. Remove the inlet hose from the appliance by loosening the ring nut. 12. Close the pump cover. 2 1 When you drain the water with the emergency drain procedure, you must activate the drain system again: a. Put 2 litres of water in the main wash compartment of the detergent dispenser. b. Start the programme to drain the water. 3. Clean the valve filter on the back of the appliance with a toothbrush. 15.
www.aeg.com 15.10 Frost precautions If the appliance is installed in an area where the temperature can reach the values around 0° C or drop below, remove the remaining water from the inlet hose and the drain pump. 45° 20° 15.9 Emergency drain If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain pump' paragraph. If necessary, clean the pump. 1. Disconnect the mains plug from the mains socket. 2. Close the water tap. 3.
ENGLISH 39 The programme was not finished properly or the appliance stopped too early. If the alarm code appears again, contact the Authorised Service Centre. • • - The mains supply is unstable. Wait until the mains supply is stable. • - No communication between electronic elements of the appliance. Switch it off and switch on again. - The anti-flood device is on. Disconnect the appliance and close the water tap. Contact the Authorised Service Centre.
www.aeg.com Problem Possible solution The appliance does not drain the water. • Make sure that the sink spigot is not clogged. • Make sure that the drain hose has no kinks or bends. • Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning". • Make sure that the connection of the drain hose is correct. • Set the drain programme if you set a programme without drain phase.
ENGLISH 41 Problem Possible solution The washing results are not satisfactory. • Increase the detergent quantity or use a different detergent. • Use special products to remove the stubborn stains before you wash the laundry. • Make sure that you set the correct temperature. • Decrease the laundry load. Too much foam in the • Reduce the quantity of detergent. drum during the washing cycle. After the washing cycle, there are some detergent residues in the dispenser drawer.
www.aeg.com the meanwhile, open the appliance door. Make sure that the water level inside the drum is not too high. If necessary, proceed with an emergency drain (refer to «Emergency drain» in «Care and cleaning» chapter). To open the door, proceed as follows: 1. Press the On/Off button to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4. Pull the emergency unlock trigger downward once. Pull it downward once again, keep it tensed and, in 5.
ENGLISH Programmes Load (kg) Wool/Handwash 30°C 43 Energy Water conApproximate proconsump- sumption (li- gramme duration tion (kWh) tre) (minutes) 1.5 0.35 57 60 1) «Cotton Energy Saving programme » at 60°C with a load of 8kg is the reference programme for the data entered in the energy label, in compliance with 96/60/EC Directive. 18.
www.aeg.com 19. ACCESSORIES 19.3 Pedestal with the drawer 19.1 Available in www.aeg.com/shop or from authorised dealer Only appropriate accessories approved by AEG ensure the safety standards of the appliance. If unapproved parts are used, any claims will be invalidated. 19.2 Fixing plate kit If you install the appliance on a plinth, secure the appliance with the fixing plates. Read carefully the instructions supplied with the accessory.
ENGLISH 45
www.aeg.
ENGLISH 47
157024370-A-372018 www.aeg.
