L7WEE861R USER MANUAL EN User Manual Washer Dryer
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................6 3. INSTALLATION............................................................................................................7 4. PRODUCT DESCRIPTION.........................................................................................12 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • • • • • • • • • • • • • The appliance shall be installed as a freestanding product or below the kitchen worktop if space margins permit. Do not install the appliance behind a lockable door, a sliding door or a door with a hinge on the opposite side, that would prevent the appliance door from being fully open. Connect the mains plug to the mains socket only at the end of the installation process. Make sure that the mains plug is accessible after installation.
ENGLISH • • • • • • • • • • • 5 Items that have been soiled with substances such as vegetable or mineral oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed separately with an extra amount of detergent before being dried in the washer dryer. Do not use the appliance if items have been soiled with industrial chemicals. Do not dry unwashed items in the wash dryer.
www.aeg.com 2. SAFETY INSTRUCTIONS 2.1 Installation The installation must comply with relevant national regulations. • Follow the installation instructions supplied with the appliance. • Do not install or use the appliance where the temperature can be less than 0°C or where it is exposed to the weather. • Always keep the appliance vertical when it is being moved. • Make sure that there is air circulation between the appliance and the floor. • Remove all the packaging and the transit bolts.
ENGLISH – If a detergent ball is used, remove it before starting a drying programme. – Do not use a detergent ball if setting a non-stop programme. WARNING! Risk of injury or damage to the appliance. • Do not sit or stand on the open door. • Do not dry dripping wet clothes in the appliance. 7 • Cut off the mains electrical cable close to the appliance and dispose of it. • Remove the door catch to prevent children or pets from becoming trapped in the drum.
www.aeg.com 5. Carefully put down the appliance with the rear side on it. 6. Put the front polystyrene packaging element on the floor under the appliance. Make sure not to damage the hoses. 9. Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliance in factory. 7. Remove the polystyrene protection from the bottom. 10.
ENGLISH We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.2 Installation on suspended flooring Suspended wooden floors are particularly susceptible to vibration. To limit vibration we recommend placing a waterproof wooden panel, at least 15 mm thick, under the appliance. It should be screwed to at least 2 floor beams and should extend beyond the front feet. If possible, install the appliance where the floor is more stable. 3.3 Positioning and levelling 1.
www.aeg.com You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. It is possible to connect the drain hose in different ways: 45 20 O O Make sure that the inlet hose is not in vertical position. 3. If necessary, loose the ring nut to set it in the correct position. 4. Connect the water inlet hose to the cold water tap with 3/4" thread. 1. Make a U shape with the drain hose and put it around the plastic hose guide. 2.
ENGLISH 11 5. Without the plastic hose guide, to a sink spigot - Put the drain hose in the spigot and tighten it with a clamp. Refer to the illustration. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm min. 1.5") must be larger than the external diameter of the drain hose. 4. If the end of the drain hose looks like this (see the picture), you can push it directly into the stand pipe.
www.aeg.com 4. PRODUCT DESCRIPTION 4.
ENGLISH 13 5. CONTROL PANEL 5.1 Control panel description 3 2 1 Programme Time Drying Cottons Cottons Eco Synthetics Delicates Wool/Handwash Outdoor Anti-Allergy NonStop 60min Steam Rinse Temp. Stains Spin Prewash Spin Wash 12 5.
www.aeg.com Maximum load indicator. The icon flashes during laundry load estimation (refer to "PROSENSE load detection" paragraph). Maximum laundry indicator. It flashes when the laundry load exceeds the maximum declared load of the selected programme. If you run a programme when the drum is overloaded, end of the programme. also flashes at the Drying time indicator. Door locked indicator. The digital indicator can show: , washing and/or drying phase). • Programme duration (e. g. • Delay time (e. g.
ENGLISH 15 6. DIAL AND BUTTONS 6.1 On/Off Pressing this button for a few seconds allows to activate or deactivate the appliance. Two different tunes sound while switching the appliance on or off. As the Stand-by function automatically deactivates the appliance to decrease the energy consumption in a few cases, you may need to activate the appliance again. For more details, refer to Stand-by paragraph in Daily Use chapter. 6.
www.aeg.com This option is recommended for heavily soiled laundry, especially if containing sand, dust , mud and other solid particles. "Timed drying" table). The display shows the set value. Each time you touch this button the time value increases by 5 minutes. The options can increase the programme duration. You cannot set all time values for different types of fabrics. 6.6 Delay Start With this option you can delay the start of a programme in a more convenient time.
ENGLISH 17 7. PROGRAMMES 7.1 Programme Chart Programme Programme description Washing programmes Cottons Cottons Eco White cotton and coloured cotton. Normal, heavy and light soil. White cotton and coloured cotton. Normal, heavy and light soil. Cottons energy saving programme. This programme at 60ºC with a load of 8 kg is the reference programme for data entered in the energy label, in compliance with EEC 92/75 standards.
www.aeg.com Programme Programme description NonStop 60min Complete programme composed of a washing phase and of a drying phase for a small load of mixed fabrics (cotton and synthetic items). appears on the display. Also, the indicator Steam programme Steam programmes2) Steam Steam can be used for dried, washed or worn once laundry. These programmes can reduce creases and odours and make your laundry softer. Do not use any detergent.
ENGLISH Programme 19 Default tempera- Maximum spin speed Maximum load ture Spin speed range Temperature range Synthetics 40 °C 60 °C - Cold 1200 rpm 1200 rpm - 400 rpm 4 kg Delicates 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 4 kg Wool/Handwash 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 1.5 kg Outdoor 30 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 2.
Prewash ■ ■ ■ ■ Stains1) ■ ■ ■ ■ ■ Delay Start ■ ■ ■ ■ Quick Wash2) ■ ■ ■ ■ Time Drying ■ ■ ■ ■ Auto Drying ■ ■3) ■ ■ ■ ■ Rinse ■ ■ Steam Delicates ■ NonStop 60min Synthetics ■ Anti-Allergy Cottons Eco ■ Outdoor Cottons ■ Options Extra Rinse Wool/Handwash www.aeg.com Programme 20 ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) This option is not available with temperature lower than 40 °C. 2) If you set the shortest duration, we recommend that you decrease the load size.
ENGLISH 21 In UK, Eire, Hong Kong and India the Woolmark symbol is a certification trademark. 7.
www.aeg.
ENGLISH • After you touch the Start/Pause button: all the buttons and the programme dial are deactivated (except On/Off button ). • Before you touch the Start/Pause button: the appliance cannot start. The appliance keeps the selection of this option after you switch it off. completed, touch the Stains/Prewash and the Delay Start buttons simultaneously for about 6 seconds. 9.2 Acoustic signals 9.
www.aeg.com CAUTION! Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. 10.3 Filling the detergent and additives 10.4 Check the position of the flap 1. Pull out the detergent dispenser until it stops. 2. Press the lever down to remove the dispenser. 1 2 3. To use powder detergent, turn the flap up. Compartment for prewash phase, soak programme or stain remover. Compartment for washing phase.
ENGLISH With the flap in the position DOWN: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid detergent than the limit shown on the flap. • Do not set the prewash phase. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser. 25 To perform washing only, make sure that only the Wash indicator is on above the Mode button.
www.aeg.com Changing the delay start after the countdown has started this case, it will be not possible to guarantee the best washing results. About 20 minutes after the programme start, the programme duration could be adjusted again depending on the capacity of water absorption of the fabrics. To change the delay start: 1. Touch the Start/Pause button to pause the appliance. The related indicator flashes. 2. Touch the Delay Start button repeatedly until the display shows the desired delay time. 3.
ENGLISH 10.11 Cancelling a running programme 1. Press the button On/Off to cancel the programme and to deactivate the appliance. 2. Press the button On/Off again to activate the appliance. Now, you can set a new washing programme. If the ProSense phase is already carried out and the water filling is already started, the new programme starts without repeating the ProSense phase. The water and the detergent are not drained out in order to avoid waste.
www.aeg.com 1. If necessary, touch the Spin button to decrease the spin speed proposed by the appliance. 2. Press Start/Pause to continue the cycle 3. When the programme is completed and the door locked indicator goes off, you can open the door. 4. Press the On/Off button a few seconds to deactivate the appliance. In any case, the appliance empties the water out automatically after approximately 18 hours. • You do not use the appliance for 5 minutes before you touch the Start/ Pause button.
ENGLISH The time value on the display is the duration of both cycles washing and drying, calculated on a default load size. To have a good drying by using less energy and in a shorter time, the appliance does not let you set a too low spin speed for the items to be washed and dried. 2. Touch button Start/Pause to start the programme. The PROSENSE estimation starts. In the display the door locked indicator goes on, the indicator of the running phase starts flashing.
www.aeg.com When drying a big amount of laundry, to have good drying performances, make sure that the laundry itself is not rolled up and that is uniformly distributed in the drum. 12.2 Drying - Automatic levels 1. Tap on the Auto Drying button repeatedly until the display shows the required dryness level. The indicators in the display illuminate accordingly: a. b. items; Iron dry: for cotton Cupboard dry: for cotton and synthetic items; Extra dry: for cotton items.
ENGLISH • To dry this type of fabrics at open air when they are washed the first time. • To clean the drain filter. • After the drying phase, clean the empty drum, the gasket and the door with a wet cloth. To remove the fluff inside the drum, set a special programme: • Empty the drum. • Clean the drum, the gasket and the door with a wet cloth. 31 • Set the rinse programme. • Simultaneously press the Spin and the Quick Wash buttons until the display shows CLE to activate the cleaning function.
www.aeg.com other treatments without exceeding the indicated maximum level ( ). • Use the recommended detergents for the type and colour of the fabric, the programme temperature and the level of soil. 14.4 Ecological hints • Set a programme without the prewash phase to wash laundry with normal soil. • Always start a washing programme with the maximum load of laundry allowed. • If you pre-treat the stains or use a stain remover, set a programme with a low temperature.
ENGLISH 1. Use fabric conditioner in the washing cycle. 2. Use special fabric conditioner for tumble dryers. 33 When the drying programme is completed remove the laundry promptly. 15. CARE AND CLEANING WARNING! Refer to Safety chapters. 15.1 External cleaning Clean the appliance with mild soap and warm water only. Fully dry all the surfaces. CAUTION! Do not use alcohol, solvents or chemical products.
www.aeg.com detergent dispenser drawer, once in a while carry out the following cleaning procedure: 1. Open the drawer. Press the catch downwards as indicated in the picture and pull it out. 4. Insert the detergent drawer into the guide rails and close it. Run the rinsing programme without any clothes in the drum. 1 2 15.7 Cleaning the drain pump 2.
ENGLISH 35 6. Repeat the steps 4 and 5 until the water stops to flow out. 7. Turn the filter anti-clockwise to remove it. 2 1 2. Place a suitable bowl below the drain pump access to collect the water that flows out. 3. Open the chute downwards. Always keep a rag nearby to dry up any water spillages when removing the filter. 4. Turn the filter 180 degrees in anticlockwise direction to open it, without removing. Let the water flow out. 5.
www.aeg.com 2 1 2 1 3 2. Remove the inlet hose from the appliance by loosening the ring nut. 12. Close the pump cover. 2 1 When you drain the water with the emergency drain procedure, you must activate the drain system again: a. Put 2 litres of water in the main wash compartment of the detergent dispenser. b. Start the programme to drain the water. 3. Clean the valve filter on the back of the appliance with a toothbrush. 15.
ENGLISH 37 15.10 Frost precautions If the appliance is installed in an area where the temperature can reach the values around 0° C or drop below, remove the remaining water from the inlet hose and the drain pump. 45° 20° 15.9 Emergency drain If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain filter' paragraph. If necessary, clean the pump. 1. Disconnect the mains plug from the mains socket. 2. Close the water tap. 3.
www.aeg.com The programme was not finished properly or the appliance stopped too early. If the alarm code appears again, contact the Authorised Service Centre. • • - The mains supply is unstable. Wait until the mains supply is stable. • - No communication between electronic elements of the appliance. Switch it off and switch on again. - The anti-flood device is on. Disconnect the appliance and close the water tap. Contact the Authorised Service Centre.
ENGLISH 39 Problem Possible solution The appliance does not drain the water. • Make sure that the sink spigot is not clogged. • Make sure that the drain hose has no kinks or bends. • Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning". • Make sure that the connection of the drain hose is correct. • Set the drain programme if you set a programme without drain phase. • Set the drain programme if you set an option which ends with water in the tub.
www.aeg.com Problem Possible solution The washing results are not satisfactory. • Increase the detergent quantity or use a different detergent. • Use special products to remove the stubborn stains before you wash the laundry. • Make sure that you set the correct temperature. • Decrease the laundry load. Too much foam in the • Reduce the quantity of detergent. drum during the washing cycle. After the washing cycle, there are some detergent residues in the dispenser drawer.
ENGLISH 41 Make sure that the water level inside the drum is not too high. If necessary, proceed with an emergency drain (refer to «Emergency drain» in «Care and cleaning» chapter). To open the door, proceed as follows: 1. Press the On/Off button to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4. Pull twice the emergency unlock trigger downward and open the appliance door. 5. Take out the laundry and then close the appliance door. 6.
www.aeg.com Programmes Load (kg) Wool/Handwash 30°C Energy Water conApproximate proconsump- sumption (li- gramme duration tion (kWh) tre) (minutes) 1.5 0.35 57 60 1) «Cotton Energy Saving programme » at 60°C with a load of 8kg is the reference programme for the data entered in the energy label, in compliance with EEC 92/75 standards. 18.
ENGLISH 43 19. ACCESSORIES 19.3 Pedestal with the drawer 19.1 Available in www.aeg.com/shop or from authorised dealer Only appropriate accessories approved by AEG ensure the safety standards of the appliance. If unapproved parts are used, any claims will be invalidated. 19.2 Fixing plate kit If you install the appliance on a plinth, secure the appliance with the fixing plates. Read carefully the instructions supplied with the accessory.
157012102-A-502017 www.aeg.