L7WEG841R USER MANUAL EN User Manual Washer Dryer
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................6 3. INSTALLATION............................................................................................................7 4. PRODUCT DESCRIPTION.........................................................................................12 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • • • • • • • • • • This appliance is intended to be used in household and similar applications such as: – staff kitchen areas in shops, offices and other working environments; – by clients in hotels, motels, bed & breakfast and other residential type environments; – areas for communal use in blocks of flats or in launderettes. The appliance shall be installed as a freestanding product or below the kitchen worktop if space margins permit.
ENGLISH • • • • • • • • • • • • • 5 The appliance must be connected to the water mains using the new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre. Old hose sets must not be reused. If the mains power supply cable is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an electrical hazard. Wipe away lint or packaging debris that has accumulated around the appliance.
www.aeg.com • • Clean the appliance with a moist cloth. Use only neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. 2. SAFETY INSTRUCTIONS 2.1 Installation The installation must comply with relevant national regulations. • Follow the installation instructions supplied with the appliance.
ENGLISH 2.4 Use WARNING! Risk of injury, electric shock, fire, burns or damage to the appliance. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. • Do not touch the glass door while a programme is in operation. The glass can get hot. • Do not dry damaged (torn, frayed) items that contain padding or fillings. • If laundry has been washed with a stain remover, carry out an additional rinse cycle before starting a drying cycle.
www.aeg.com 7. Remove the polystyrene protection from the bottom. 1 3. Remove the internal film. 2 8. Pull up the appliance in vertical position. 4. Open the door and remove the polystyrene piece from the door seal and all the items from the drum. 9. Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliance in factory. 5. Carefully put the appliance down on its rear side. 6.
ENGLISH 2. Loosen or tighten the feet to adjust the level. WARNING! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level. 11. Pull out the plastic spacers. 12. Put the plastic caps, that you find in the user manual bag, in the holes. x4 The appliance must be level and stable. We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.
www.aeg.com 2. Position it toward left or right depending on the position of the water tap. 45 20 O O A If this occurs, close the water tap and contact the authorized service centre to replace the hose. 3.6 Water drainage The drain hose should be positioned at a height of not less than 60 cm and not more than 100 cm from the floor. Make sure that the inlet hose is not in vertical position. 3. If necessary, loose the ring nut to set it in the correct position. 4.
ENGLISH Make sure that the drain hose end is not immersed in the water. There may be a return of dirty water into the appliance. 3. To a stand pipe with vent-hole Insert the drain hose directly into a drain pipe. Refer to the illustration. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm min. 1.5") must be larger than the external diameter of the drain hose. 4.
www.aeg.com 4. PRODUCT DESCRIPTION 4.
ENGLISH 13 5. CONTROL PANEL 5.1 Control panel description 3 2 1 Programme Time Drying Cottons Cottons Eco Synthetics Delicates Wool/Handwash Outdoor NonStop 60min Steam Rinse Spin/Drain Temp.
www.aeg.com Maximum laundry indicator. It flashes when the laundry load exceeds the maximum declared load of the selected programme. If you run a programme when the drum is overloaded, end of the programme. also flashes at the Drying time indicator. Door locked indicator. The digital indicator can show: , washing and/or drying phase). • Programme duration (e. g. • Delay time (e. g. or ). • Cycle end ( ). • Warning code ( ). Washing phase indicator. It flashes during prewash and wash phase.
ENGLISH 15 6. DIAL AND BUTTONS 6.1 Introduction When pressing a key combination, do not tilt your fingers downwards . The sensors of the underneath buttons are sensitive and may interfere with Your choice. 6.2 On/Off Pressing this button for a few seconds allows to activate or deactivate the appliance. Two different tunes sound while switching the appliance on or off.
www.aeg.com The options can increase the programme duration. Each time you touch this button the time value increases by 5 minutes. You cannot set all time values for different types of fabrics. 6.7 Delay Start With this option you can delay the start of a programme in a more convenient time. Tap on the button repeatedly to set the required delay. The time increases by steps of 30 minutes up to 90' and from 2 hours up to 20 h.
ENGLISH Programme Programme description Cottons White cotton and coloured cotton. Normal, heavy and light soil. Cottons Eco 17 White cotton and coloured cotton. Normal, heavy and light soil. Cottons energy saving programme. This programme at 60ºC with a load of 8 kg is the reference programme for data entered in the energy label, in compliance with 96/60/EC Directive. Set this programme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended.
www.aeg.com Programme Programme description Steam programmes2) Steam Steam can be used for dried, washed or worn once laundry. These programmes can reduce creases and odours and make your laundry softer. Do not use any detergent. If necessary, remove stains by washing or using localized stain removal. Steam programmes do not perform any hygienic cycle. Do not set a Steam programme with these types of items: • Items to be washed at a temperature lower than 40°C.
ENGLISH Programme Default tempera- Reference spin ture speed Temperature Spin speed range range 19 Maximum load Delicates 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 3 kg Wool/Handwash 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 1.5 kg Outdoor 30 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 2 kg NonStop 60min 30 °C 40 °C - 30 °C 1200 rpm 1200 rpm 1 kg 1.
Cottons Cottons Eco Synthetics Delicates Outdoor NonStop 60min Steam Rinse Spin/Drain Wool/Handwash www.aeg.com Programme 20 Delay Start ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Time Drying ■ ■ ■ ■ ■ ■ Auto Drying ■ ■4) Options 1) If you set No Spin option, the appliance only drains the water. 2) This option is not available with temperature lower than 40 °C. 3) If you set the shortest duration, we recommend that you decrease the load size.
ENGLISH Dryness Level Cupboard Dry1) For items to be stored Type of fabric Load Cottons and Linen (bathrobes, bath towels, etc) up to 4 kg 21 Synthetics and mixed fabup to 3 kg rics (jumpers, blouses, underwear, household and bed linen) Delicate fabrics up to 2 kg (acrylics, viscose and delicate mixed fabrics) Wool items (woollen jumpers) up to 1 kg Outdoor sporting garments up to 2 kg (Outdoor clothing, technical, sport fabrics, waterproof and breathable jackets, shell jackets) Iron Dry Suitable
www.aeg.
ENGLISH If you deactivate the acoustic signals, they continue operate when the appliance has a malfunction. 8.4 Permanent Extra Rinse With this option you can permanently have one or two extra rinses when you set a new programme. • Simultaneously touch the Temp. button and the Spin button once to 23 add one extra rinse. appears on the display. • Simultaneously touch the Temp. button and the Spin button twice to add two extra rinses. appears on the display. • Simultaneously touch the Temp.
www.aeg.com Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum indicated level ( ). This quantity will however guarantee the best washing results. CAUTION! Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. 10.3 Filling the detergent and additives Compartment for prewash phase, soak programme or stain remover. Compartment for washing phase.
ENGLISH 4. To use liquid detergent, turn the flap down. B With the flap in the position DOWN: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid detergent than the limit shown on the flap. • Do not set the prewash phase. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser. 25 The indicator of the Start/Pause button flashes.
www.aeg.com The PROSENSE estimation starts at the end of the countdown. At the end of the load detection, in case of drum overload, the indicator flashing in the display: is Cancelling the delay start after the countdown has started In this case, for 30 seconds, it is possible to pause the appliance and remove the exceeding garments. To cancel the delay start: Once removed the exceeding garments, touch the Start/Pause button to start the programme again.
ENGLISH 10.10 Interrupting a programme and changing the options When the programme is running, you can change only some options: 1. Touch the button Start/Pause. The related indicator flashes. 2. Change the options. The given information in the display changes accordingly. 3. Touch the button Start/Pause again. The washing programme continues. 10.11 Cancelling a running programme 1. Press the button On/Off to cancel the programme and to deactivate the appliance. 2.
www.aeg.com • You do not use the appliance for 5 minutes before you touch the Start/ Pause button. Press the button On/Off to activate the appliance again. • After 5 minutes from the end of the washing programme Press the On/Off button to activate the appliance again. The display shows the end of the last set programme. Turn the programme dial to set a new cycle.
ENGLISH c. Extra dry: for cotton items. The time value on the display is the duration of both cycles washing and drying, calculated on a default load size. To have a good drying by using less energy and in a shorter time, the appliance does not let you set a too low spin speed for the items to be washed and dried. 2. Touch button Start/Pause to start the programme. The PROSENSE estimation starts. In the display the door locked indicator goes on, the indicator of the running phase starts flashing.
www.aeg.com When drying a big amount of laundry, to have good drying performances, make sure that the laundry itself is not rolled up and that is uniformly distributed in the drum. 12.2 Drying - Automatic levels 1. Tap on the Auto Drying button repeatedly until the display shows the required dryness level. The indicators in the display illuminate accordingly: a. b. items; Iron dry: for cotton Cupboard dry: for cotton and synthetic items; Extra dry: for cotton items.
ENGLISH • To dry this type of fabrics at open air when they are washed the first time. • To clean the drain filter. • After the drying phase, clean the empty drum, the gasket and the door with a wet cloth. To remove the fluff inside the drum, set a special programme: • Empty the drum. • Clean the drum, the gasket and the door with a wet cloth. 31 • Set the rinse programme. • Simultaneously press the Spin and the Quick Wash buttons until the display shows CLE to activate the cleaning function.
www.aeg.com other treatments without exceeding the indicated maximum level ( ). • Use the recommended detergents for the type and colour of the fabric, the programme temperature and the level of soil. 14.4 Ecological hints • Set a programme without the prewash phase to wash laundry with normal soil. • Always start a washing programme with the maximum load of laundry allowed. • If you pre-treat the stains or use a stain remover, set a programme with a low temperature.
ENGLISH 2. Use special fabric conditioner for tumble dryers. 33 When the drying programme is completed remove the laundry promptly. 15. CARE AND CLEANING WARNING! Refer to Safety chapters. 15.1 External cleaning Clean the appliance with mild soap and warm water only. Fully dry all the surfaces. CAUTION! Do not use alcohol, solvents or chemical products. run a maintenance wash regularly (at least once a month): 1. Remove all laundry from the drum. 2.
www.aeg.com Always follow the instructions that you find on the packaging of the product. 2. Run a short cotton programme at high temperature with empty drum and with a small quantity of powder detergent or, if available, run the Machine Clean programme. 3. Make sure that all detergent residue is removed from the upper and lower part of the recess. Use a small brush to clean the recess. 15.
ENGLISH 35 WARNING! • Do not remove the filter while the appliance operates. • Do not clean the pump if the water in the appliance is hot. Wait until the water cools down Proceed as follows to clean the pump: 1. Open the pump cover. 2 5. When the bowl is full of water, turn the filter back and empty the container. 6. Repeat the steps 4 and 5 until the water stops to flow out. 7. Turn the filter anti-clockwise to remove it. 1 2.
www.aeg.com 15.8 Cleaning the inlet hose and the valve filter It is recommended to clean both the filters of the inlet hose and valve occasionally to remove any deposit, collected over the time: 1. Remove the inlet hose from the tap and clean the filter. 1 11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 2 2 3 2. Remove the inlet hose from the appliance by loosening the ring nut. 1 12.
ENGLISH 37 15.10 Frost precautions If the appliance is installed in an area where the temperature can reach the values around 0° C or drop below, remove the remaining water from the inlet hose and the drain pump. 45° 20° 15.9 Emergency drain If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain pump' paragraph. If necessary, clean the pump. 1. Disconnect the mains plug from the mains socket. 2. Close the water tap. 3.
www.aeg.com The programme was not finished properly or the appliance stopped too early. If the alarm code appears again, contact the Authorised Service Centre. • • - The mains supply is unstable. Wait until the mains supply is stable. • - No communication between electronic elements of the appliance. Switch it off and switch on again. - The anti-flood device is on. Disconnect the appliance and close the water tap. Contact the Authorised Service Centre.
ENGLISH 39 Problem Possible solution The appliance does not drain the water. • Make sure that the sink spigot is not clogged. • Make sure that the drain hose has no kinks or bends. • Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning". • Make sure that the connection of the drain hose is correct. • Set the drain programme if you set a programme without drain phase. • Set the drain programme if you set an option which ends with water in the tub.
www.aeg.com Problem Possible solution The washing results are not satisfactory. • Increase the detergent quantity or use a different detergent. • Use special products to remove the stubborn stains before you wash the laundry. • Make sure that you set the correct temperature. • Decrease the laundry load. Too much foam in the • Reduce the quantity of detergent. drum during the washing cycle. After the washing cycle, there are some detergent residues in the dispenser drawer.
ENGLISH 41 the meanwhile, open the appliance door. Make sure that the water level inside the drum is not too high. If necessary, proceed with an emergency drain (refer to «Emergency drain» in «Care and cleaning» chapter). To open the door, proceed as follows: 1. Press the On/Off button to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4. Pull the emergency unlock trigger downward once. Pull it downward once again, keep it tensed and, in 5.
www.aeg.com Programmes Load (kg) Wool/Handwash 30°C Energy Water conApproximate proconsump- sumption (li- gramme duration tion (kWh) tre) (minutes) 1.5 0.30 60 75 1) «Cotton Energy Saving programme » at 60°C with a load of 8kg is the reference programme for the data entered in the energy label, in compliance with 96/60/EC Directive. 18.
ENGLISH 43 19. ACCESSORIES 19.1 Available in www.aeg.com/shop or from authorised dealer Only appropriate accessories approved by AEG ensure the safety standards of the appliance. If unapproved parts are used, any claims will be invalidated. 19.2 Fixing plate kit If you install the appliance on a plinth, secure the appliance with the fixing plates. Read carefully the instructions supplied with the accessory. 20. ENVIRONMENTAL CONCERNS Recycle materials with the symbol .
157024430-A-372018 www.aeg.
