L7WEG851R USER MANUAL EN User Manual Washer Dryer
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................5 3. INSTALLATION............................................................................................................7 4. PRODUCT DESCRIPTION.........................................................................................11 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • • • • • • • • • • • • Do not install the appliance behind a lockable door, a sliding door or a door with a hinge on the opposite side, that would prevent the appliance door from being fully opened. Connect the mains plug to the mains socket only at the end of the installation process. Make sure that the mains plug is accessible after installation. The ventilation opening in the base (if applicable) must not be covered by a carpet, mat, or any floor covering.
ENGLISH • • • • • • • • • • 5 Do not use the appliance if items have been soiled with industrial chemicals. Do not dry unwashed items in the wash dryer. Items such as foam rubber (latex foam), shower caps, waterproof textiles, and rubber backed articles and clothes, or pillows fitted with foam rubber pads should not be dried in the washer dryer. Fabric softeners, or similar products, should only be used as specified by the product manufacturer’s instructions.
www.aeg.com • Do not install or use a damaged appliance. • Do not install the appliance where the appliance door cannot be fully opened. • Adjust the feet to have the necessary space between the appliance and the flooring. • When the appliance is in its permanent position, check that it is fully level with the aid of a spirit level. If it is not, adjust the feet accordingly. 2.2 Electrical Connection WARNING! Risk of fire and electrical shock. • The appliance must be earthed.
ENGLISH 7 3. INSTALLATION WARNING! Refer to Safety chapters. 4. Open the door and remove the polystyrene piece from the door seal and all the items from the drum. 3.1 Unpacking WARNING! Remove all the packaging and the transit bolts before installing the appliance. WARNING! Use the gloves. 1. Remove the external film. If necessary, use a cutter. 5. Carefully put down the appliance with the rear side on it. 6. Put the front polystyrene packaging element on the floor under the appliance.
www.aeg.com 9. Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliance in factory. We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.2 Installation on suspended flooring Suspended wooden floors are particularly susceptible to vibration.
ENGLISH 45 20 9 O O x4 The appliance must be level and stable. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. 3.4 The inlet hose 1. Connect the water inlet hose to the back of the appliance. 2. Position it toward left or right depending on the position of the water tap. Make sure that the inlet hose is not in vertical position. 3. If necessary, loose the ring nut to set it in the correct position. 4.
www.aeg.com A If this occur, close the water tap and contact the authorized service centre to replace the hose. 3.6 Water drainage The drain hose should stay at a height of not less than 60 cm and not more than 100 cm. You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. Make sure that the drain hose end is not immersed in the water. There may be a return of dirty water into the appliance. 3.
ENGLISH 5. Without the plastic hose guide, to a sink spigot - Put the drain hose in the spigot and tighten it with a clamp. Refer to the illustration. 6. Position the hose directly to a builtin drain pipe in the room wall and tighten it with a clamp. Make sure that the drain hose makes a loop to prevent particles going into the appliance from the sink. 4. PRODUCT DESCRIPTION 4.
www.aeg.com 5. CONTROL PANEL 5.1 Control panel description 3 2 1 Programme Time Drying Cottons Cottons Eco Synthetics Delicates Wool/Handwash Outdoor NonStop 60min Steam Rinse Spin/Drain Temp.
ENGLISH Maximum laundry indicator. It flashes when the laundry load exceeds the maximum declared load of the selected programme. If you run a programme when the drum is overloaded, end of the programme. also flashes at the Drying time indicator. Door locked indicator. The digital indicator can show: , washing and/or drying phase). • Programme duration (e. g. • Delay time (e. g. or ). • Cycle end ( ). • Warning code ( ). Washing phase indicator. It flashes during prewash and wash phase.
www.aeg.com 6. DIAL AND BUTTONS 6.1 On/Off Pressing this button for a few seconds allows to activate or deactivate the appliance. Two different tunes sound while switching the appliance on or off. As the Stand-by function automatically deactivates the appliance to decrease the energy consumption in a few cases, you may need to activate the appliance again. For more details, refer to Stand-by paragraph in Daily Use chapter. 6.
ENGLISH The options can increase the programme duration. Each time you touch this button the time value increases by 5 minutes. You cannot set all time values for different types of fabrics. 6.6 Delay Start With this option you can delay the start of a programme in a more convenient time. Tap on the button repeatedly to set the required delay. The time increases by steps of 30 minutes up to 90' and from 2 hours up to 20 h.
www.aeg.com Programme Programme description White cotton and coloured cotton. Normal soil and light soil. Cottons Cottons Eco White cotton and coloured cotton. Normal soil and light soil. Cottons energy saving programme. This programme at a 60ºC with a load of 8 kg is the reference programme for data entered in the energy label, in compliance with EEC 92/75 standards. Set this programme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended.
ENGLISH Programme 17 Programme description Steam programmes2) Steam Steam can be used for dried, washed or worn once laundry. These programmes can reduce creases and odours and make your laundry softer. Do not use any detergent. If necessary, remove stains by washing or using localized stain removal. Steam programmes do not perform any hygienic cycle. Do not set a Steam programme with these types of items: • Items to be washed at a temperature lower than 40°C.
www.aeg.com Programme Default tempera- Maximum spin speed Maximum load ture Spin speed range Temperature range Delicates 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 3 kg Wool/Handwash 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 1.5 kg Outdoor 30 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 2 kg NonStop 60min. 30 °C 40 °C - 30 °C 1200 rpm 1200 rpm 1 kg 1.
Synthetics Delicates Outdoor NonStop 60min. Steam Rinse Spin/Drain Wool/Handwash Cottons Eco 19 Cottons Programme ENGLISH Delay Start ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Time Drying ■ ■ ■ ■ ■ ■ Auto Drying ■ ■ Options 1) If you set No Spin option, the appliance only drains the water. 2) This option is not available with temperature lower than 40 °C. 3) If you set the shortest duration, we recommend that you decrease the load size.
www.aeg.
ENGLISH Dryness Level Type of fabric Cupboard Dry For items to be stored Cottons and Linen (bathrobes, bath towels, etc) Iron Dry Suitable for ironing Load (kg) 21 Spin Suggesspeed ted du(rpm) ration (mins) 5 1600 190 - 210 2 1600 85 - 100 1 1600 50 - 60 Synthetics and mixed fabrics (jumpers, blouses, underwear, household linen) 3 1200 130 - 145 1 1200 45 - 55 Delicates (acrylics, viscose and delicate mixed fabrics) 2 1200 150 Wool (woollen jumpers) 1 1200 170 - 190 Outdoor
www.aeg.com • Simultaneously touch the Temp. button and the Spin button once to add one extra rinse. appears on the display. • Simultaneously touch the Temp. button and the Spin button twice to add two extra rinses. the display. • Simultaneously touch the Temp. button and the Spin button three times to remove extra rinses. The display only shows . appears on 9. BEFORE FIRST USE 1. Make sure that all transit bolts have been removed from the appliance. 2.
ENGLISH 23 10.3 Filling the detergent and additives 3. To use powder detergent, turn the flap up. A Compartment for prewash phase, soak programme or stain remover. Compartment for washing phase. Compartment for liquid additives (fabric conditioner, starch). Maximum level for quantity of liquid additives. Flap for powder or liquid detergent. Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum indicated level ( ).
www.aeg.com With the flap in the position DOWN: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid detergent than the limit shown on the flap. • Do not set the prewash phase. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser. To perform washing only, make sure that only the Wash indicator is on above the Mode button.
ENGLISH Changing the delay start after the countdown has started this case, it will be not possible to guarantee the best washing results. About 20 minutes after the programme start, the programme duration could be adjusted again depending on the capacity of water absorption of the fabrics. To change the delay start: 1. Touch the Start/Pause button to pause the appliance. The related indicator flashes. 2. Touch the Delay Start button repeatedly until the display shows the desired delay time. 3.
www.aeg.com 10.11 Cancelling a running programme 1. Press the button On/Off to cancel the programme and to deactivate the appliance. 2. Press the button On/Off again to activate the appliance. Now, you can set a new washing programme. If the ProSense phase is already carried out and the water filling is already started, the new programme starts without repeating the ProSense phase. The water and the detergent are not drained out in order to avoid waste.
ENGLISH 3. Press the On/Off button a few seconds to deactivate the appliance. In any case, the appliance empties the water out automatically after approximately 18 hours. 10.15 Stand-by option 27 • After 5 minutes from the end of the washing programme Press the On/Off button to activate the appliance again. The display shows the end of the last set programme. Turn the programme dial to set a new cycle.
www.aeg.com To have a good drying by using less energy and in a shorter time, the appliance does not let you set a too low spin speed for the items to be washed and dried. 2. Touch button Start/Pause to start the programme. The PROSENSE estimation starts. In the display the door locked indicator goes on, the indicator of the running phase starts flashing. The display also shows the remaining programme time. 11.3 Washing and Timed Drying 1.
ENGLISH 12.2 Drying - Automatic levels 1. Tap on the Auto Drying button repeatedly until the display shows the required dryness level. The indicators in the display illuminate accordingly: a. b. items; Iron dry: for cotton Cupboard dry: for cotton and synthetic items; Extra dry: for cotton items. The display shows the drying programme duration. c.
www.aeg.com To remove the fluff inside the drum, set a special programme: • Empty the drum. • Clean the drum, the gasket and the door with a wet cloth. • Set the rinse programme. • Simultaneously press the Spin and the Quick Wash buttons until the display shows CLE to activate the cleaning function. • Touch the Start/Pause button to start the programme. If the appliance is frequently used, carry out the CLE programme regularly. 14. HINTS AND TIPS WARNING! Refer to Safety chapters. 14.
ENGLISH • Use the recommended detergents for the type and colour of the fabric, the programme temperature and the level of soil. 14.4 Ecological hints • Set a programme without the prewash phase to wash laundry with normal soil. • Always start a washing programme with the maximum load of laundry allowed. • If you pre-treat the stains, you can use a stain remover when you set a programme with a low temperature. • To use the correct quantity of detergent, check the water hardness of your domestic system.
www.aeg.com 2. Use special fabric conditioner for tumble dryers. When the drying programme is completed remove the laundry promptly. 15. CARE AND CLEANING WARNING! Refer to Safety chapters. 15.1 External cleaning Clean the appliance with mild soap and warm water only. Fully dry all the surfaces. run a maintenance wash regularly (at least once a month): 1. Remove all laundry from the drum. 2. Run a cotton programme with the highest temperature with a small quantity of powder detergent. 15.
ENGLISH 33 1. Open the drawer. Press the catch downwards as indicated in the picture and pull it out. 1 2 15.7 Cleaning the drain pump 2. Remove the top part of the additive compartment to aid cleaning and flush it out under running warm water, to remove any traces of accumulated detergent. After cleaning, replace the top part in its position. WARNING! Disconnect the mains plug from the mains socket. Regularly check the drain pump filter and make sure that it is clean.
www.aeg.com 2 1 2 1 2. Place a suitable bowl below the drain pump access to collect the water that flows out. 3. Squeeze the two levers and pull the drainage duct forward to open it. 1 1 7. Close the drainage duct and turn the filter anti-clockwise to remove it. 2 1 2 4. Let the water flow out. 5. When the bowl is full of water, close the drainage duct back and empty the container. 6. Repeat the steps 4 and 5 until the water stops to flowing out. 8.
ENGLISH 35 15.8 Cleaning the inlet hose and the valve filter It is recommended to clean both the filters of the inlet hose and valve occasionally to remove any deposit, collected over the time: 1. Remove the inlet hose from the tap and clean the filter. 1 11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 2 3 2 1 2. Remove the inlet hose from the appliance by loosening the ring nut. 12. Close the pump access.
www.aeg.com 15.10 Frost precautions If the appliance is installed in an area where the temperature can reach the values around 0° C or drop below, remove the remaining water from the inlet hose and the drain pump. 45° 20° 15.9 Emergency drain If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain filter' paragraph. If necessary, clean the pump. 1. Disconnect the mains plug from the mains socket. 2. Close the water tap. 3.
ENGLISH • - No communication between electronic elements of the appliance. Switch it off and switch on again. • - The anti-flood device is on. Disconnect the appliance and close the water tap. Contact the Authorised Service Centre. 37 WARNING! Deactivate the appliance before carrying out any check. 16.2 Possible failures Problem Possible solution The programme does not start. • Make sure that the mains plug is connected to the mains socket. • Make sure that the appliance door is closed.
www.aeg.com Problem Possible solution There is water on the floor. • Make sure that the couplings of the water hoses are tight and there is not water leakages. • Make sure that the water inlet hose and the drain hose have no damages. • Make sure you use the correct detergent and the correct quantity of it. You cannot open the appliance door. • Make sure that a washing programme that ends with water in tub, has been selected. • Make sure that the washing programme is finished.
ENGLISH 39 Problem Possible solution The laundry is full of different colours fluff. The fabrics washed in the previous cycle released fluff of a different colour: • The drying phase helps to eliminate some fluff. • Clean the clothes with a fluff remover. In case of an excessive amount of fluff in the drum run the special programme to clean it (refer to “Fluff in the fabrics" for more details). After the check, activate the appliance. The programme continues from the point of interruption.
www.aeg.com 17. CONSUMPTION VALUES Stated values are obtained in laboratory conditions with relevant standards. Different causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also affect the washing programme duration. Technical specifications may be changed without prior notice to improve the quality of product.
ENGLISH 1) Water supply pressure Minimum Maximum 0,5 bar (0,05 MPa) 8 bar (0,8 MPa) Maximum wash load Cotton 8 kg Maximum dry load Cotton Synthetics 5 kg 3 kg Spin Speed Maximum 1600 rpm 41 1) The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your domestic cold water storage system. Make sure not to exceed a distance of 5.02 m (16.
www.aeg.com To raise your appliance and makes loading and unloading laundry easier. Read carefully the instructions supplied with the accessory. The drawer can be used for laundry storage e.g.: towels, cleaning products and more. 20. ENVIRONMENTAL CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances.
ENGLISH 43
157009610-C-212017 www.aeg.
