L 87490 FL FR Notice d'utilisation
www.aeg.com SOMMAIRE 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. CONSIGNES DE SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTRUCTIONS DE SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 CARACTERISTIQUES TECHNIQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 DESCRIPTION DE L'APPAREIL . . . . . . . . . . . . . . . . . . . . . . . .
FRANÇAIS 3 1. CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.1 Sécurité des enfants et des personnes vulnérables AVERTISSEMENT Risque d'asphyxie, de blessure ou d'invalidité permanente.
www.aeg.com • Respectez la charge maximale de 9 kg (reportez-vous au chapitre « Tableau des programmes »). • Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son atelier d'entretien ou un technicien qualifié afin d'éviter tout danger. • La pression de l'eau en service (minimale et maximale) doit être comprise entre 0,5 bar (0,05 MPa) et 8 bar (0,8 MPa) • Les orifices d'aération situés à la base (si présents) ne doivent pas être obstrués par de la moquette.
FRANÇAIS 5 tallation. Assurez-vous que la prise de courant est accessible une fois l'appareil installé. • Ne tirez jamais sur le câble d'alimentation électrique pour débrancher l'appareil. Tirez toujours sur la prise. • Ne touchez jamais le câble d'alimentation ou la prise avec des mains mouillées. • Cet appareil est conforme aux directives CEE. • Ne placez pas de produits inflammables ou d'éléments imbibés de produits inflammables à l'intérieur, à proximité ou sur l'appareil.
www.aeg.com 3.
FRANÇAIS 11 Dispositifs de protection 7 12 Pieds pour que l'appareil soit de ni- veau 4.1 Accessoires 1 1 Clé 2 4 Pour retirer les dispositifs de protection. 2 Caches en plastique Pour boucher les orifices situés à l'arrière de l'appareil après avoir retiré les dispositifs de protection. 3 Tuyau anti-débordement Pour éviter toute fuite éventuelle 4 Guide en plastique Pour relier le tuyau de vidange au bord d'un évier. 3 d’une montre jusqu’à ce que la rainure soit verticale. 4.
www.aeg.com 5 Touche Départ différé (Départ Dif- féré) 6 Touche Gain de temps (Gains de Temps) 7 Touche Rinçage plus (Rinçage Plus) 8 Touche Prélavage/Taches (Taches/ Prélav.) 9 Touche Réduction d'essorage (Esso- rage) 10 Touche Température (Temp.) 5.1 Bouton Arrêt AUTOMATIQUE 1 • Vous n'utilisez pas la machine pendant 5 minutes avant d'appuyer sur le bouton 4 . – Toutes les sélections sont annulées. – Appuyez sur le bouton 1 pour remettre la machine en marche.
FRANÇAIS 9 Phase de lavage Phase de rinçage Phase d'essorage Les symboles des phases • Lorsqu'un programme est sélectionné, tous les symboles des phases correspondant au programme apparaissent. • Lorsque le programme démarre, seul le symbole de la phase en cours clignote. • Lorsque le programme est terminé, le symbole de la dernière phase s'allume. D Le symbole vapeur s'allume lorsque vous choisissez un programme Vapeur.
www.aeg.com Le symbole de la sécurité enfants s'allume lorsque le verrouillage est activé. I Barres graphiques Une barre vide apparaît si la fonction correspondante est compatible avec le programme sélectionné. La barre se remplit en fonction des sélections. Si vous faites une mauvaise sélection, le message Err s'affiche, vous indiquant que cette sélection n'est pas possible.
FRANÇAIS 11 5.8 La touche Prélavage/ Taches 8 5.11 Fonction des signaux sonores. Appuyez sur la touche 8 pour ajouter l'option Taches et/ou prélavage à un programme. Appuyez plusieurs fois sur la touche pour activer une ou deux options. Le symbole correspondant et la barre de voyants apparaissent sur l'afficheur. Des signaux sonores retentissent lorsque: • le lave-linge est mis en fonctionnement. • le lave-linge est mis à l'arrêt. • les touches sont activées. • Le programme est terminé.
www.aeg.com multanément jusqu'à ce que l'afficheur indique le symbole . • Pour désactiver la fonction, appuyez sur la touche 6 et sur la touche 5 simultanément jusqu'à ce que le symbole disparaisse. . 6. PROGRAMMES Programme Température Type de charge Poids max. de la charge Description du cycle Fonctions Blanc/Couleurs 95° - 0° Coton blanc et couleur articles normalement sales.
FRANÇAIS Programme Température Type de charge Poids max. de la charge Délicats 40 - 0° Textiles délicats Lavage comme l'acrylique, Rinçage la viscose, le poly- Essorage court ester, normalement sales. Charge maximale 4 kg RÉDUCTION D'ESSORAGE ARRÊT CUVE PLEINE PRÉLAVAGE1) RINÇAGE PLUS TACHES2) GAIN DE TEMPS Articles en laine la- Lavage vables en machine. Rinçage Lainages et tissus Essorage court délicats lavables à la main (portant le symbole « lavage à la main »).
www.aeg.com Programme Température Type de charge Poids max. de la charge Description du cycle Fonctions Essorage / Vidange5) 0° Tous textiles. La charge maximum est fonction du type de lessive. Charge maximale 9 kg Vidange Phase d'essorage. RÉDUCTION D'ESSORAGE Rinçage 0° Tous textiles. Charge maximale 9 kg un rinçage avec ad- RÉDUCTION ditif D'ESSORAGE phase d'essorage ARRÊT CUVE PLEINE RINÇAGE PLUS6) Jeans 60° - 0° Tous les articles en Lavage jean.
FRANÇAIS 15 4) Les phases de lavage et d'essorage de ce programme sont douces pour éviter que le linge ne se froisse. L'appareil effectue des rinçages supplémentaires. 5) Réglez la vitesse d'essorage. Assurez-vous qu'elle corresponde au linge.Pour sélectionner le programme VIDANGE uniquement, sélectionnez la fonction SANS ESSORAGE. 6) Appuyez sur la touche RINCAGE SUPPLEMENTAIRE pour ajouter des rinçages.
www.aeg.com 7. VALEURS DE CONSOMMATION Au démarrage du programme, l'affichage indique la durée du programme pour la charge maximale. Durant la phase de lavage, la durée du programme est calculée automatiquement. Elle peut être réduite si la charge de linge est inférieure à la capacité maximale (par exemple, pour le programme Coton 60 °C, dont la capacité maximale est de 9 kg, la durée du programme est de plus de 2 heures ; pour une charge réelle de 1 kg, la durée du programme est inférieure à 1 heure).
FRANÇAIS 17 8. AVANT LA PREMIÈRE UTILISATION Pour activer le système d'essorage, versez 2 litres d'eau dans le compartiment pour le lavage principal. 2. Versez une petite quantité de lessive dans le compartiment pour le lavage principal. Sélectionnez et faites démarrer un programme pour coton à vide à la température la plus élevée qui soit afin de vider le tambour et la cuve de toute poussière éventuelle. 1. 9. UTILISATION DE L'APPAREIL 1. 2. 3. Ouvrez le robinet d'arrivée d'eau.
www.aeg.com Compartiment à lessive pour la phase de prélavage et le programme de trempage Ajoutez la lessive pour le prélavage et le trempage avant le départ du programme. Compartiment pour la phase de lavage Si vous utilisez de la lessive liquide, versez-la immédiatement avant de démarrer le programme. Compartiment des additifs liquides (assouplissant, amidon). Versez le produit dans le compartiment avant de démarrer le programme. Niveau de quantité maximum pour les additifs liquides.
FRANÇAIS 4. 19 Pour utiliser de la lessive liquide, tournez la languette vers le bas. Avec la languette en position BASSE : – N'utilisez pas de lessives liquides gélatineuses ou épaisses. – N'insérez pas de lessive liquide au-delà de la limite figurant sur la languette. – Ne sélectionnez pas de phase de prélavage. – Ne sélectionnez pas la fonction Départ différé. 5. 6. Dosez les produits de lavage et l’adoucissant. Fermez soigneusement le distributeur du produit de lavage.
www.aeg.com 9.6 Modification d'une fonction Vous ne pouvez modifier que quelques fonctions avant qu'elles soient actives. 1. Appuyez sur la touche 4 . Le voyant clignote. 2. Modifiez la fonction réglée. 9.7 Sélectionnez le départ différé. 1. Appuyez plusieurs fois sur la touche 5 jusqu'à ce que le délai du départ différé souhaité apparaisse sur l'afficheur. Les symboles correspondants apparaissent. 2. Appuyez sur la touche 4 , le décompte du départ différé commence.
FRANÇAIS – Vous devez vidanger l'eau pour ouvrir le hublot. Pour vidanger l'eau : 1. Si besoin est, diminuez la vitesse d'essorage. 2. Appuyez sur la touche DEPART/ PAUSE 4 . L'appareil vidange et essore. 21 3. Une fois le programme terminé et le symbole de verrouillage de la porte éteint, vous pouvez ouvrir la porte. 4. Mettez à l'arrêt l'appareil. L'appareil vidange et essore automatiquement au bout d'environ 18 heures. 10. CONSEILS 10.1 Chargement du linge 10.
www.aeg.com les lave-linge. Dans les régions où l'eau est douce, il n'est pas nécessaire d'utiliser un adoucisseur d'eau. Pour connaître la dureté de l'eau dans votre région, prenez contact avec l'organisme local de distribution d'eau. Respectez les instructions qui se trouvent sur les emballages de ces produits. Ces échelles d'équivalence mesurent la dureté de l'eau : • Degrés allemands (dH°). • Degrés français (°TH).
FRANÇAIS 23 11.4 Joint du hublot Examinez régulièrement le joint et enlevez tous les objets situés à l'intérieur. 11.5 Tambour Examinez régulièrement le tambour pour éviter la formation de calcaire ou de particules de rouille. N'utilisez que des produits spéciaux pour éliminer les particules de rouille du tambour. Pour ceci : • Nettoyez le tambour à l'aide d'un produit spécial inox. • Mettez en route un programme coton court à température maximale avec une petite quantité de lessive. 11.
www.aeg.com AVERTISSEMENT 1. Débranchez l'appareil électriquement. 2. Ne retirez pas le filtre pendant que l'appareil fonctionne. Ne nettoyez pas la pompe de vidange si l'eau de l'appareil est chaude. L'eau doit être froide pour que vous puissiez nettoyer la pompe de vidange. 11.7 Pompe de vidange Examinez régulièrement la pompe de vidange et assurez-vous qu'elle est propre. Nettoyez la pompe si : • L'appareil ne vidange pas. • Le tambour ne tourne pas.
FRANÇAIS 2 1 11.8 Le filtre du tuyau d'arrivée d'eau et le filtre de la soupape 7. Enlevez les peluches et les objets de la pompe. 8. Assurez-vous que la turbine de la pompe tourne. Si ce n'est pas le cas, contactez votre service aprèsvente. 25 9. Nettoyez le filtre sous l'eau courante et remettez-le en place dans la pompe en l'insérant dans les glissières prévues spécialement à cet effet. 10. Assurez-vous de visser correctement le filtre pour empêcher les fuites. 11.
www.aeg.com 4. 5. 6. 7. 20° Retirez le tuyau d'alimentation situé à l'arrière de l'appareil. Nettoyez le filtre de la soupape à l'aide d'une petite brosse dure ou d'un chiffon. Réinstallez le tuyau d'alimentation. Assurez-vous que tous les raccords de tuyaux d’eau sont bien serrés afin d’éviter toute fuite. Ouvrez le robinet d'arrivée d'eau. 45° 11.9 Vidange d'urgence : L'appareil ne vidange pas à cause d'une anomalie de fonctionnement.
FRANÇAIS Dans certains cas, le signal sonore retentit et l'écran affiche un code d'alarme : • - L'appareil n'est pas approvisionné en eau. • - L'appareil ne vidange pas. • • 27 - Le système de sécurité anti-débordement s'est déclenché. AVERTISSEMENT Mettez l'appareil à l'arrêt avant de procéder aux vérifications. - La porte de l'appareil est ouverte ou ne se ferme pas correctement. Problème Cause possible L'appareil n'est Le robinet d'arrivée pas approvisionné d’eau est fermé. en eau.
www.aeg.com Problème Cause possible Solution possible Le système de sécurité anti-débordement s'est déclenché. • Débranchez l'appareil. • Fermez le robinet d'arrivée d'eau. • Contactez votre service après-vente. La phase d'essora- La phase d'essorage est ge ne fonctionne désactivée. pas. Sélectionnez le programme d'essorage. Le programme ne démarre pas. Le filtre de la pompe de vidange est obstrué. Nettoyez le filtre de la pompe de vidange. Reportez-vous au chapitre « Entretien et nettoyage ».
FRANÇAIS Problème 29 Cause possible Solution possible Vous n'avez pas retiré l'emballage et/ou les boulons de transport. Retirez l'emballage et/ou les boulons de transport. Consultez le paragraphe « Installation ». La charge est très petite. Ajoutez plus de linge dans le tambour. L'appareil se rem- L'extrémité du tuyau de plit d'eau et vividange est placée trop dange immédiate- bas. ment. Assurez-vous que le tuyau de vidange est dans une position correcte.
www.aeg.com 2. 3. Retirez la partie supérieure du carton. Retirez les cales en polystyrène. 4. Retirez le film interne. 5. Ouvrez le hublot. Retirez la cale en polystyrène du joint du hublot et tous les articles présents dans le tambour. 6. Placez l'une des cales en polystyrène au sol derrière l'appareil. Couchez avec soin l'appareil sur le dos. Assurez-vous de ne pas endommager les tuyaux.
FRANÇAIS 7. 8. 31 Retirez la base en polystyrène en bas de l'appareil. Remettez l'appareil en position verticale. 1 2 9. Retirez le câble d'alimentation électrique et le tuyau de vidange de leurs supports. 10. Desserrez les trois boulons. Utilisez la clé fournie avec l'appareil. 11. Retirez les entretoises en plastique. 12. Mettez les bouchons en plastique dans les orifices. Ces bouchons se trouvent dans le même sachet que la notice d'utilisation.
www.aeg.com AVERTISSEMENT Retirez toutes les attaches de transport et les dispositifs de sécurité avant d'installer l'appareil. Nous vous recommandons de conserver l'emballage et les dispositifs de sécurité en vue d'un éventuel déménagement de l'appareil. 13.3 Positionnement et mise à niveau • Placez l'appareil sur un sol plat et dur. • Assurez-vous que la circulation de l'air sous l'appareil ne soit pas entravée par des tapis. • Veillez à ce que l'appareil ne touche pas le mur ou les autres meubles.
FRANÇAIS 33 13.4 Le tuyau d'arrivée • Reliez le tuyau à l'appareil. Le tuyau d'alimentation peut être orienté vers la gauche ou la droite. Desserrez la bague pour qu'il soit bien positionné. 20 O 45 O • Raccordez le tuyau d'arrivée d'eau à un robinet fileté (3/4 po). ATTENTION Assurez-vous que les raccords ne fuient pas. N'utilisez pas de rallonge si le tuyau d'alimentation est trop court. Contactez le service aprèsvente pour remplacer le tuyau d'alimentation.
www.aeg.com 13.5 Vidange de l'eau Il existe différentes procédures pour raccorder le tuyau de vidange : Avec le guide de tuyau en plastique. • Sur le bord d'un évier. • Veillez à ce que le guide de tuyau en plastique ne puisse pas se déplacer quand l'appareil se vidange. Fixez le guide au robinet d'arrivée d'eau ou au mur. • À une conduite fixe dotée d'une ventilation spéciale. Reportez-vous à l'illustration.
FRANÇAIS 35 • Directement dans une canalisation de vidange murale intégrée et serrez-le avec une attache. La longueur maximale du tuyau de vidange est de 400 cm. Contactez le service après-vente pour les autres longueurs de tuyaux de vidange et les rallonges. 14. EN MATIÈRE DE PROTECTION DE L'ENVIRONNEMENT Recyclez les matériaux portant le symbole . Déposez les emballages dans les conteneurs prévus à cet effet.
132939811-A-502012 www.aeg.