L 87495 XFL ES LAVADORA MANUAL DE INSTRUCCIONES
www.aeg.com ÍNDICE DE MATERIAS 4 5 7 7 8 13 18 18 18 18 20 21 23 25 30 33 INFORMACIÓN SOBRE SEGURIDAD INFORMACIÓN TÉCNICA DESCRIPCIÓN DEL PRODUCTO ACCESORIOS PANEL DE MANDOS PROGRAMAS ANTES DEL PRIMER USO UTILIZACIÓN DEL APARATO CARGAR LA COLADA INTRODUCCIÓN DEL DETERGENTE Y LOS ADITIVOS AJUSTE E INICIO DE UN PROGRAMA AL FINAL DEL PROGRAMA CONSEJOS ÚTILES MANTENIMIENTO Y LIMPIEZA SOLUCIÓN DE PROBLEMAS INSTALACIÓN ASPECTOS MEDIOAMBIENTALES Recicle los materiales con el símbolo .
ESPAÑOL 3 PARA OBTENER RESULTADOS PERFECTOS Gracias por escoger este producto AEG. Este artículo ha sido creado para ofrecer un rendimiento impecable durante muchos años, con innovadoras tecnologías que facilitarán su vida y prestaciones que probablemente no encuentre en electrodomésticos corrientes. Por favor, dedique algunos minutos a la lectura para disfrutar de todas sus ventajas.
www.aeg.com INFORMACIÓN SOBRE SEGURIDAD Antes de instalar y usar el aparato, lea atentamente este manual: • Por su seguridad y la de su hogar • Para respetar el medio ambiente • Por el correcto funcionamiento del aparato. Guarde siempre estas instrucciones junto con el aparato, aunque se mude o lo dé a otra persona. El fabricante no se hace responsable de los daños causados por una instalación incorrecta.
ESPAÑOL • No instale ni enchufe un aparato dañado. • Asegúrese de quitar todos los pasadores del embalaje y transporte. • Asegúrese de que el enchufe está desconectado de la toma de red durante la instalación. • La instalación, fontanería y conexiones eléctricas del aparato debe realizarlas tan sólo un técnico profesional homologado. De esta forma se evitarán riesgos de daños estructurales y lesiones. • No instale ni utilice el aparato en lugares con temperaturas inferiores a 0 ºC.
www.aeg.com El nivel de protección contra la entrada de partículas sólidas y humedad está garantizado por la tapa protectora, excepto si el equipo de alta tensión no tiene protección contra la humedad. Presión del suministro de Mínima agua Máxima IPX4 0.5 bares (0.05 MPa) 8 bares (0.8 MPa) Suministro de agua 1) Agua fría Carga máxima Algodón Velocidad de centrifugado Máxima 9 kg 1400 rpm 1) Conecte la manguera de entrada de agua a un grifo con rosca de 3/4 pulgadas.
ESPAÑOL DESCRIPCIÓN DEL PRODUCTO 1 2 3 8 9 10 4 5 11 6 12 7 1 Encimera 7 Pata para nivelación del aparato 2 Dosificador de detergente 8 Tubo de desagüe 3 Panel de mandos 4 Tirador de la puerta 9 Válvula de entrada de agua 10 Cable de alimentación 5 Placa de características 11 Pasadores de transporte 6 Bomba de desagüe 12 Pata para nivelación del aparato ACCESORIOS 1 4 2 3 1 Llave inglesa Para retirar los pasadores de transporte.
www.aeg.com PANEL DE MANDOS 1 2 3 10 1 Tecla de encendido/apagado (Auto Off) 2 Selector de programas 3 Pantalla 4 Botón de inicio/pausa (Inicio/Pausa) 5 Tecla de inicio diferido (Inicio Diferi- do) 9 8 7 6 5 4 7 Botón de aclarado extra (Aclarado Extra) 8 Botón Prelavado/Manchas (Manchas/ Prélavado) 9 Tecla de reducción del centrifugado (Centrifuga) 10 Tecla de Temperatura (Temp.
ESPAÑOL PANTALLA 3 A B C D L E K F G J H I La pantalla muestra: La temperatura del programa ajustado A Agua fría La velocidad de centrifugado del programa ajustado B Símbolo Sin centrifugado1) Símbolo Agua en la cuba 1) Solo disponible para el programa Centrifugado/Descarga. Fase de prelavado Fase de lavado Fase de aclarados Fase de centrifugado C Los símbolos de la fase • Cuando se ajusta un programa, todos los símbolos de las fases correspondientes al programa se encienden.
www.aeg.com No se puede abrir la puerta del aparato cuando el símbolo está encendido. Puede abrir la puerta únicamente cuando el símbolo se apague. F Si el programa termina pero el símbolo sigue encendido: • La función "Agua en la cuba" está encendida. • Hay agua en el tambor. El símbolo del inicio diferido se enciende cuando se ajusta esta función. G • Duración del programa Cuando se inicia el programa, el tiempo se reduce a intervalos de 1 minuto.
ESPAÑOL 11 La barra indicadora está llena por completo cuando se ajusta el número máximo de aclarados. El símbolo de Manchas se enciende cuando se activa esta función. L El símbolo de Prelavado se enciende cuando se activa esta función. La barra indicadora no está completamente llena cuando se ajusta únicamente una de las funciones. La barra indicadora está completamente llena cuando se ajustan dos funciones. BOTÓN DE INICIO/PAUSA 4 pondiente y la barra indicadora se encienden en la pantalla.
www.aeg.com BOTÓN DE TEMPERATURA 10 Pulse el botón 10 para cambiar la temperatura predeterminada. Cuando la pantalla muestra - -, el aparato no calienta el agua. FUNCIÓN DE SEÑALES ACÚSTICAS Suena una señal acústica cuando: • Se enciende el aparato. • Se apaga el aparato. • Se pulsan las teclas. • El programa se termina. • Se ha producido algún fallo. Para desactivar/activar las señales acústicas, pulse el botón 8 y el botón 7 al mismo tiempo durante 6 segundos.
ESPAÑOL 13 PROGRAMAS Programa Temperatura Tipo de carga Peso máx. de la carga DesFunciones cripción de ciclo Algódon 95° - 0° Algodón blanco y de color con suciedad normal. Carga máxima 9 kg Lavado Aclarados Centrifugado largo REDUCCIÓN DEL CENTRIFUGADO PROLONGACIÓN DE ACLARADO PRELAVADO 1) AQUACARE MANCHAS2) AHORRA TIEMPO3) Extra Silencio 95° - 0° Algodón blanco y de color con suciedad normal.
www.aeg.com Programa Temperatura Tipo de carga Peso máx. de la carga DesFunciones cripción de ciclo Lana / Seda 40 - 0° Lana lavable a máquina. Lana lavable a mano y tejidos delicados con el símbolo «lavado a mano». Carga máxima 2 kg Lavado Aclarados Centrifugado corto REDUCCIÓN DEL CENTRIFUGADO PROLONGACIÓN DE ACLARADO Mantas/Edredones 60 - 30° Una manta sintética, edredón, colcha, etc.
ESPAÑOL 15 Programa Temperatura Tipo de carga Peso máx. de la carga DesFunciones cripción de ciclo 20 Min. - 3 kg 40° - 30° Prendas sintéticas y de algodón con poca suciedad o que se han llevado una sola vez. Carga máxima 3 kg Lavado Aclarados Centrifugado corto REDUCCIÓN DEL CENTRIFUGADO Super Eco7) 0° Tejidos mixtos (algodón y sintéticos).
www.aeg.com Vapor Refrescar Este ciclo elimina los olores de la colada. Prendas de algodón y sintéticas. hasta 1.5 kg Prendas de algodón y sintéticas. hasta 1.5 kg El vapor no elimina los olores de animales. Vapor Anti-arrugas Este ciclo ayuda a reducir las arrugas de la colada. El vapor se puede usar para las prendas secadas, lavadas o que se han puesto una vez. Estos programas pueden reducir la cantidad de arrugas y los olores y suavizar las prendas. No utilice detergente.
ESPAÑOL Programas Algodón estándar 40 °C red. (kg) Consumo energético (KWh) Consumo de agua (litros) Duración aproximada del programa (minutos) Humedad restante (%)1) 4 0.46 40 178 44 1) Al finalizar la fase de centrifugado. Modelo L 87495 XFL 17 Modo apagado (W) Modo encendido izquierdo (W) 0.05 0.
www.aeg.com ANTES DEL PRIMER USO Para activar el sistema de desagüe, vierta 2 litros de agua en el compartimento de lavado principal del dosificador de detergente. 2. Coloque una pequeña cantidad en el compartimento de lavado principal del dosificador. Ajuste e inicie un programa para algodón a la temperatura más alta sin colada. De esta forma se elimina toda la posible suciedad del tambor y de la cuba. 1. UTILIZACIÓN DEL APARATO 1. 2. 3. Abra el grifo. Conecte el enchufe a la toma de red.
ESPAÑOL 19 El compartimento de detergente para la fase de prelavado y el programa de remojo. Añada el detergente para el prelavado y remoje antes de iniciar el programa. El compartimento de detergente para la fase de lavado. Si utiliza detergente líquido, introdúzcalo inmediatamente antes de iniciar el programa. Compartimento para aditivos líquidos (suavizante, almidón). Ponga el producto en el compartimento antes de iniciar el programa. Es el nivel máximo para la cantidad de aditivos líquidos.
www.aeg.com 4. Para usar detergente líquido, gire la tapa hacia abajo. Con la tapa en posición BAJADA: – No utilice detergentes líquidos gelatinosos ni gruesos. – No ponga más detergente líquido que el límite mostrado en la tapa. – No ajuste la fase de prelavado. – No ajuste la función de inicio diferido. 5. 6. Dosifique el detergente y el suavizante. Cierre con cuidado el dosificador de detergente. Asegúrese de que la tapa no obstruye nada al cerrar el cajón. AJUSTE E INICIO DE UN PROGRAMA 1.
ESPAÑOL El aparato no desagua. CAMBIO DE UNA FUNCIÓN Puede cambiar únicamente algunas funciones antes de usarlas. 1. Pulse la tecla 4 . El indicador parpadea. 2. Cambio de la función ajustada. AJUSTE DEL INICIO DIFERIDO 1. 2. Pulse el botón 5 repetidamente hasta que la pantalla muestre el número de minutos u horas. Los símbolos correspondientes se encienden. Pulse la tecla 4 ; el aparato inicia la cuenta atrás del inicio diferido.
www.aeg.com – La puerta permanece bloqueada. – Debe drenar el agua para abrir la puerta. Para descargar el agua: 1. Si fuera necesario, reduzca la velocidad de centrifugado. 2. Pulse el botón Inicio/Pausa 4 . El aparato vacía el agua y centrifuga. 3. Cuando el programa termina y el símbolo de bloqueo de la puerta se apaga, puede abrir la puerta. 4. Apague el aparato. El aparato vacía el agua y centrifuga automáticamente después de unas 18 horas.
ESPAÑOL 23 CONSEJOS ÚTILES CARGAR LA COLADA • Divida la colada en: ropa blanca, ropa de color, ropa sintética, prendas delicadas y prendas de lana. • Siga las instrucciones de lavado que se encuentran en las etiquetas de las prendas. • No lave juntas las prendas blancas y de color. • Algunas prendas de color pueden desteñir en el primer lavado. Se recomienda lavarlas por separado la primera vez. • Abotone las fundas de almohadas y cierre las cremalleras, los ganchos y los broches. Ate las correas.
www.aeg.com Tabla de dureza del agua Nivel Tipo Dureza agua °dH °T.H. mmol/l Clarke 1 blanda 0-7 0-15 0-1.5 0-9 2 intermedio 8-14 16-25 1.6-2.5 10-16 3 dura 15-21 26-37 2.6-3.7 17-25 4 muy dura > 21 > 37 >3.
ESPAÑOL 25 MANTENIMIENTO Y LIMPIEZA ADVERTENCIA Desconecte el aparato de la fuente de alimentación antes de limpiarlo. DESCALCIFICACIÓN El agua corriente que utilizamos suele contener cal. Si es necesario, use un descalcificador de agua para eliminar la cal. Use un producto especial para lavadoras. Siga siempre las instrucciones que se encuentran en el envase del fabricante. Hágalo de forma separada del lavado de la colada. LIMPIEZA DEL EXTERIOR Limpie el aparato solo con agua templada y jabón.
www.aeg.com DOSIFICADOR DE DETERGENTE Para limpiar el dosificador: 1 1. 2. Presione la palanca. Tire del dosificador hacia fuera. 3. Retire la parte superior del compartimento de aditivo líquido. Limpie todas las piezas con agua. 2 4. 5. 6. BOMBA DE DESAGÜE Examine periódicamente la bomba de desagüe y asegúrese de que está limpia. Limpie la bomba si: • El aparato no desagua. • El tambor no gira. • El aparato hace ruidos extraños debido al bloqueo de la bomba.
ESPAÑOL 27 Para limpiar la bomba de desagüe: 1. Abra la puerta de acceso a la bomba. 2. Tire de la tapa para extraerlo. 3. Coloque un recipiente debajo del hueco de la bomba para recoger el agua que salga. Presione las dos palancas y tire del conducto de desagüe para que salga el agua. 4. 1 5. 6. Cuando el contenedor esté lleno de agua, vuelva a colocar el conducto y vacíe el contenedor. Realice los pasos 4 y 5 repetidamente hasta que no salga más agua de la bomba.
www.aeg.com 9. Limpie el filtro con agua corriente y vuelva a colocarlo en la bomba en las guías especiales. 10. Asegúrese de que lo aprieta correctamente para evitar fugas. 11. Vuelva a colocar la compuerta y cierre la puerta de la bomba. 2 1 EL FILTRO DEL TUBO DE ENTRADA Y EL FILTRO DE LA VÁLVULA • El indicador de la tecla 4 parpadea y la pantalla muestra la alarma correspondiente. Consulte "Solución de problemas". Podría ser necesario limpiar los filtros cuando: • El aparato no carga agua.
ESPAÑOL DESAGÜE DE EMERGENCIA Debido a una avería, el aparato no puede desaguar. Si esto ocurre, realice los pasos 1) a 6) del apartado "Para limpiar la bomba de desagüe". Limpie la bomba si fuera necesario. Vuelva a colocar el conducto de desagüe y cierre la compuerta de la bomba. Cuando se desagua con el procedimiento de drenaje de emergencia, se debe activar de nuevo el sistema de desagüe: 1. Coloque 2 litros de agua en el compartimento de lavado principal del dosificador de detergente. 2.
www.aeg.com SOLUCIÓN DE PROBLEMAS El aparato no se pone en marcha o se detiene durante el funcionamiento. Primero, intente buscar una solución al problema (consulte la tabla). Si no la encuentra, póngase en contacto con el servicio técnico. • - El aparato no desagua. • - La puerta del aparato está abierta o no está bien cerrada. • - El dispositivo anti inundación se ha puesto en marcha.
ESPAÑOL Problema Causa posible Posible solución El dispositivo anti inundación se ha puesto en marcha. • Desconecte la lavadora. • Cierre la toma de agua. • Póngase en contacto con el servicio técnico. La fase de centrifu- La fase de centrifugado gado no funciona. está apagada. Seleccione el programa de centrifugado. El programa no se pone en marcha. 31 El filtro de la bomba de desagüe está obstruido. Limpie el filtro de la bomba de desagüe. Consulte el capítulo "Mantenimiento y limpieza".
www.aeg.com Problema Causa posible Posible solución El aparato se llena El extremo de la mande agua y desagua guera de desagüe está inmediatamente. demasiado bajo. Asegúrese de que el tubo de desagüe se encuentra en la posición correcta. Los resultados del lavado no son satisfactorios. El detergente empleado era insuficiente o no era el adecuado. Aumente la cantidad de detergente o utilice otro diferente. No ha eliminado las manchas difíciles antes de lavar las prendas.
ESPAÑOL 33 INSTALACIÓN KIT DE LA PLACA DE FIJACIÓN (405517114) Disponible en su distribuidor autorizado. Si instala el aparato en un zócalo, asegúrelo con las placas de fijación. Siga las instrucciones que se suministran con el kit. DESEMBALAJE 1. Utilice los guantes. Retire la película externa. Si es necesario, utilice un cúter. 2. 3. Retire la cubierta de cartón. Retire los materiales del embalaje de poliestireno. 4. Retire la película interna.
www.aeg.com 5. Abra la puerta. Retire la pieza de poliestireno de la junta de la puerta y todos los elementos del tambor. 6. Extienda uno de los materiales de embalaje de poliestireno en el suelo detrás del aparato. Baje con cuidado el aparato sobre el lado posterior. Tenga cuidado para no dañar los tubos. 7. Retire la protección de poliestireno de la base. Levante el aparato hasta la posición vertical. 8. 1 2 9. Retire el cable de alimentación y el tubo de desagüe de los soportes de los tubos.
ESPAÑOL 35 10. Suelte los tres pernos. Utilice la llave suministrada con el aparato. 11. Extraiga los separadores de plástico. 12. Coloque los tapones de plástico en los orificios. Encontrará los tapones en la bolsa del manual de instrucciones. ADVERTENCIA Retire todo el embalaje y los pasadores de transporte antes de instalar el aparato. Se recomienda guardar el embalaje y los pasadores de transporte para cuando traslade el aparato.
www.aeg.com • El aparato debe estar nivelado y estable. PRECAUCIÓN No coloque cartón, madera ni materiales equivalentes bajo las patas del aparato para ajustar el nivel. EL TUBO DE ENTRADA • Conecte el tubo al aparato. Gire el tubo de entrada solo a la derecha o a la izquierda. Suelte la tuerca anular para ajustarla en la posición correcta. 20 O 45 O • Conecte el tubo de entrada de agua fría a una toma de agua fría con rosca de 3/4. PRECAUCIÓN Asegúrese de que no haya fugas de los acoplamientos.
ESPAÑOL 37 Dispositivo antifuga El tubo de entrada tiene un dispositivo antifuga. Este dispositivo evita las fugas de agua del tubo por el desgaste normal. El sector rojo de la ventana «A» muestra este fallo. Si esto ocurre, cierre el grifo de agua y póngase en contacto con el servicio técnico para cambiar el tubo. A DESAGÜE Hay distintos procedimientos para conectar el tubo de desagüe: Con la guía de plástico. • En el borde de un fregadero.
www.aeg.com Sin la guía de plástico. • A un desagüe. Consulte la ilustración. Coloque el tubo de desagüe en el sumidero y asegúrela con una brida. Asegúrese de que el tubo de desagüe realiza un bucle para evitar que las partículas restantes entren en el aparato desde el fregadero. • Directamente a un tubo de desagüe integrado en la pared de la habitación y apretando con una brida. Puede extender el tubo de desagüe hasta un máximo de 400 cm.
ESPAÑOL 39
www.aeg.