L 87495 XFL DE Benutzerinformation
www.aeg.com INHALT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SICHERHEITSINFORMATIONEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SICHERHEITSHINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNISCHE DATEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 GERÄTEBESCHREIBUNG . . . . . . . . . . . . . . . . . . . . . .
DEUTSCH 3 1. SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Sicherheit von Kindern und schutzbedürftigen Personen WARNUNG! Es besteht Erstickungsgefahr, Risiko von Verletzungen oder permanenten Behinderungen.
www.aeg.com • Nehmen Sie keine technischen Änderungen am Gerät vor. • Beachten Sie die maximale Beladungsmenge von 9 kg (siehe Kapitel „Programmtabelle“). • Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, einem autorisierten Kundendienst oder einer gleichermaßen qualifizierten Person ersetzt werden, um Gefahrenquellen zu vermeiden. • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen.
DEUTSCH • • • • • • • chen. Wenden Sie sich andernfalls an eine Elektrofachkraft. Das Gerät darf ausschließlich an eine ordnungsgemäß installierte Schutzkontaktsteckdose angeschlossen werden. Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie dies durch unseren Kundendienst durchführen.
www.aeg.com 3. TECHNISCHE DATEN Abmessungen Breite / Höhe / Tiefe Elektrischer Anschluss: 600 / 850 / 605 mm Gesamttiefe 640 mm Spannung Gesamtleistung Sicherung Frequenz 230 V 2200 W 10 A 50 Hz Die Schutzklasse gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt Wasserdruck IPX4 Min. 0,5 bar (0,05 MPa) Max.
DEUTSCH 7 Schraubfüße zum Ausrichten des Geräts 8 Wasserablaufschlauch 9 Wassereinlassventil 7 10 Netzkabel 11 Transportschrauben 12 Schraubfüße zum Ausrichten des Geräts 4.1 Zubehör 1 4 2 3 4.2 Einstellen der Kindersicherung • Bei aktivierter Kindersicherung lässt sich die Tür nicht schließen, damit Kinder oder Haustiere nicht in der Trommel eingeschlossen werden können. Zum Aktivieren der Kindersicherung drehen Sie den Schalter im Uhrzeigersinn, bis die Einkerbung horizontal ist.
www.aeg.com 5. BEDIENFELD 1 2 3 Glätten Koch/Bunt Auffrischen Baumwolle Eco Super Eco Extra Leise Pflegeleicht Leichtbügeln 20Min. - 3kg Feinwäsche Jeans Spülen Schleudern/ / Pumpen W Wolle/Seide Daunen Anti-Allergie Auto Off Temp. U./Min. Flecken/ Vorw. 10 9 8 1 Ein-/Aus-Taste (Auto Off) Extra Spülen 7 Zeit Sparen Zeitvorwahl 6 5 Start/Pause 4 10 Temperatur-Taste (Temp.
DEUTSCH 9 5.3 Display 3 A B C D L E K F G J H I Im Display erscheint: Die Temperatur des eingestellten Programms A Kaltes Wasser Die Schleuderdrehzahl des eingestellten Programms B Symbol Kein Schleudergang 1) Symbol Spülstopp 1) Nur verfügbar für das Programm Schleudern/Abpumpen. Vorwaschgang Hauptwaschgang Spülgänge Schleudergang C Phasensymbole • Wenn ein Programm ausgewählt wird, leuchten alle Symbole der im Programm vorkommenden Programmphasen auf.
www.aeg.com Das Türverriegelungssymbol erscheint, wenn das Programm beginnt. Sie können die Tür des Geräts nicht öffnen, solange dieses Symbol erscheint. Sie können die Tür erst öffnen, wenn das Symbol erlischt. F Wenn das Symbol nicht erlischt, obwohl das Programm beendet ist: • Die Spülstopp-Funktion ist eingeschaltet. • Es befindet sich Wasser in der Trommel. Das Zeitvorwahlsymbol leuchtet auf, wenn Sie die Funktion Zeitvorwahl eingestellt haben.
DEUTSCH 11 Der angezeigte Wert gibt die Gesamtanzahl der Spülgänge an. Der Anzeigebalken ist komplett gefüllt, wenn Sie die maximale Anzahl Spülgänge einstellen. Das Fleckensymbol leuchtet beim Aktivieren der Funktion auf. L Das Symbol für Vorwäsche leuchtet beim Aktivieren der Funktion auf. Der Anzeigebalken ist nicht ganz gefüllt, wenn Sie nur eine der Funktionen einstellen. Der Anzeigebalken ist vollständig gefüllt, wenn Sie beide Funktionen einstellen. 5.
www.aeg.com Das Display zeigt nur die Schleuderdrehzahlen an, die mit dem eingestellten Programm verfügbar sind. • Schalten Sie den Schleudergang aus. • Aktivieren Sie die Spülstopp-Funktion. Stellen Sie diese Funktion ein, um Knitterfalten zu vermeiden. Das Gerät pumpt das Wasser am Ende des Programms nicht ab. 5.10 Temperatur-Taste 10 Drücken Sie die Taste 10 zum Ändern der Standardtemperatur. Wenn das Display - - anzeigt, heizt das Gerät das Wasser nicht auf. 5.
DEUTSCH 13 6. PROGRAMME Programm Temperatur Wäschetyp Max. Beladung ProFunktionen grammbeschreibung Koch/Bunt 95 °C - Kalt Weiße und bunte Baumwolle, normal verschmutzt. Max. Beladung 9 kg Waschgang Spülgänge Langer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP VORWÄSCHE1) EXTRA SPÜLEN FLECKEN2) ZEIT SPAREN3) Extra Leise 95 °C - Kalt Weiße und bunte Baumwolle, normal verschmutzt. Max.
www.aeg.com Programm Temperatur Wäschetyp Max. Beladung ProFunktionen grammbeschreibung Wolle / Seide Waschmaschinenfeste Wolle. Handwaschbare Wolle und Feinwäsche mit dem „Handwäsche“-Pflegesymbol. Max. Beladung 2 kg WaschDREHZAHLREgang DUZIERUNG Spülgän- SPÜLSTOPP ge Kurzer Schleudergang Daunen 60 - 30° Eine einzelne Decke aus Synthetik, Bettdecke, Bettlaken usw. Max. Beladung 3 kg WaschDREHZAHLREgang DUZIERUNG Spülgänge Kurzer Schleudergang Anti-Allergie 60° Weiße Baumwolle.
DEUTSCH 15 Programm Temperatur Wäschetyp Max. Beladung ProFunktionen grammbeschreibung 20 Min. - 3kg 40° - 30° Teile aus Baumwolle oder Synthetik, die leicht verschmutzt sind oder nur einmal getragen wurden. Max. Beladung 3 kg WaschDREHZAHLREgang DUZIERUNG Spülgänge Kurzer Schleudergang Super Eco7) 0° Mischfasern (Baumwolle und Synthetik). Max.
www.aeg.com DAMPFPROGRAMME Programm1) Dampf Auffrischen Dieses Programm beseitigt Gerüche aus der Wäsche. Wäschetyp Max. Beladung Baumwolle und Synthetik. bis zu 1.5 kg Baumwolle und Synthetik. bis zu 1.5 kg Dampf beseitigt keine Tiergerüche. Dampf Glätten Dieses Programm hilft bei der Beseitigung von Falten in der Wäsche. Dampf kann für getrocknete, gewaschene oder einmal getragene Wäsche benutzt werden. Diese Programme können Falten und Gerüche reduzieren und machen Ihre Wäsche glatter.
DEUTSCH 17 Die Werte dieser Tabelle sind Richtwerte. Folgende Faktoren können diese Werte verändern: Die Wäscheart und -menge, die Wasser- und Raumtemperatur. Programme Beladung (kg) Energieverbrauch (kWh) Wasserverbrauch (Liter) Ungefähre Programmdauer (in Minuten) Restfeuchte (%)1) Koch-/Buntwäsche 60 °C 9 1.6 69 168 52 Koch-/Buntwäsche 40 °C 9 1.0 69 164 52 Pflegeleicht 40 °C 4 0.6 48 105 35 Feinwäsche 40 °C 4 0.7 58 86 35 Wolle/Handwäsche 30 °C 2 0.
www.aeg.com 9. GEBRAUCH DES GERÄTS 1. 2. 3. Drehen Sie den Wasserhahn auf. Stecken Sie den Netzstecker in die Steckdose. Drücken Sie die Taste 1 , um das Gerät einzuschalten. 4. Legen Sie die Wäsche in das Gerät. 5. Verwenden Sie die richtige Waschmittel- und Pflegemittelmenge. 6. Stellen Sie je nach Wäscheart und Verschmutzungsgrad das passende Waschprogramm ein. 9.1 Einfüllen der Wäsche 1. 2. Öffnen Sie die Tür des Geräts. Geben Sie jedes Wäschestück einzeln in die Trommel.
DEUTSCH 19 Waschmittelfach für die Waschphase. Wenn Sie Flüssigwaschmittel verwenden, muss dieses direkt vor dem Start des Programms eingefüllt werden. Fach für flüssige Pflegemittel (Weichspüler, Stärke). Füllen Sie das Pflegemittel in das Fach ein, bevor Sie das Programm starten. Das ist die maximale Menge für flüssige Pflegemittel. Fach für den Fleckenentferner. Füllen Sie den Fleckenentferner in das Fach ein und stellen Sie die Funktion Flecken ein, bevor Sie das Programm starten.
www.aeg.com 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. Klappe in der Position „Unten“: – Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. – Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. – Stellen Sie nicht den Vorwaschgang ein. – Stellen Sie nicht die Zeitvorwahl ein. 5. 6. Messen Sie Waschmittel und Weichspüler ab. Schließen Sie die Waschmittelschublade vorsichtig.
DEUTSCH ßend können Sie ein neues Waschprogramm einstellen. Das Gerät pumpt das Wasser nicht ab. 9.6 Ändern einer Funktion Einige Funktionen können nur geändert werden, bevor sie durchgeführt werden. 1. Drücken Sie die Taste 4 . Die Kontrolllampe blinkt. 2. Ändern Sie die eingestellte Funktion. 9.7 Einstellen der Zeitvorwahl 1. 2. Drücken Sie die Taste 5 wiederholt, bis das Display die Zeit in Minuten und Stunden anzeigt. Die entsprechenden Symbole leuchten auf.
www.aeg.com – Die Tür bleibt verriegelt. – Sie müssen das Wasser abpumpen, um die Tür zu öffnen. Abpumpen des Wassers: 1. Reduzieren Sie, falls erforderlich, die Schleuderdrehzahl. 2. Drücken Sie die Start/Pause-Taste 4 . Das Gerät pumpt das Wasser ab und schleudert. 3. Wenn das Programm beendet ist und das Türverriegelungssymbol erlischt, können Sie die Tür öffnen. 4. Schalten Sie das Gerät aus. Nach etwa 18 Stunden pumpt das Gerät automatisch das Wasser ab und schleudert. 10. TIPPS UND HINWEISE 10.
DEUTSCH 10.4 Wasserhärte Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Enthärters für Waschmaschinen. In Gegenden mit weichem Wasser ist die Zugabe eines Enthärters nicht erforderlich. Wenden Sie sich an Ihr örtliches Wasserversorgungsunternehmen, um die Wasserhärte in Ihrem Gebiet zu erfahren. 23 Halten Sie sich an die Anweisungen auf der Verpackung der Produkte.
www.aeg.com 11.4 Türdichtung Überprüfen Sie regelmäßig die Türdichtung und nehmen Sie alle Einzelteile aus dem Inneren heraus. 11.5 Trommel Überprüfen Sie regelmäßig, dass sich kein Kalk und keine Rostpartikel in der Trommel absetzen. Verwenden Sie zur Entfernung von Rost aus der Trommel nur Spezialprodukte. Vorgehensweise: • Reinigen Sie die Trommel mit einem Spezialreiniger für Edelstahl.
DEUTSCH 25 WARNUNG! 1. Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Entfernen Sie den Filter nicht, während das Gerät in Betrieb ist. Reinigen Sie die Ablaufpumpe nicht, wenn das Wasser im Gerät heiß ist. Das Wasser muss abgekühlt sein, bevor Sie die Ablaufpumpe reinigen. 11.7 Ablaufpumpe Kontrollieren Sie regelmäßig die Ablaufpumpe und sorgen Sie dafür, dass sie sauber ist. Reinigen Sie die Pumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht.
www.aeg.com 2 1 11.8 Zulaufschlauchfilter und Ventilfilter Die Filter müssen in folgenden Fällen gereinigt werden: • Es läuft kein Wasser in das Gerät. • Das Wasser läuft sehr lange in das Gerät ein. 7. Entfernen Sie Flusen und Gegenstände aus der Pumpe. 8. Vergewissern Sie sich, dass sich das Flügelrad der Pumpe drehen kann. Wenn dies nicht möglich ist, wenden Sie sich an den Kundendienst. 9.
DEUTSCH 4. 5. 6. 20° 45° 7. 11.9 Notentleerung 1. Das Gerät kann aufgrund einer Funktionsstörung das Wasser nicht abpumpen. In diesem Fall führen Sie die Schritte (1) bis (6) unter „So reinigen Sie die Ablaufpumpe“ durch. Reinigen Sie bei Bedarf die Pumpe. Bringen Sie den Ablaufkanal wieder in seine ursprüngliche Position und schließen Sie die Ablaufpumpenklappe. Wenn Sie das Wasser über das Notentleerungsverfahren abpumpen, müssen Sie das Abpumpsystem wieder aktivieren: 1.
www.aeg.com 12. FEHLERSUCHE Das Gerät startet nicht oder stoppt während des Betriebs. Versuchen Sie zunächst eine Lösung für das Problem zu finden (siehe Tabelle). Wenn Sie keine Lösung finden, wenden Sie sich an den Kundendienst. • - Das Gerät pumpt das Wasser nicht ab. • - Die Gerätetür steht offen oder ist nicht richtig geschlossen. • - Die Aquasafe-Einrichtung ist ausgelöst.
DEUTSCH Problem Mögliche Ursache 29 Mögliche Abhilfe Die Gerätetür steht offen oder ist nicht richtig geschlossen. Schließen Sie die Tür richtig. Die Aquasafe-Einrichtung ist aktiv. • Schalten Sie das Gerät aus. • Schließen Sie den Wasserhahn. • Wenden Sie sich an den Kundendienst. Das Gerät schleudert nicht. Das Programm startet nicht. Es befindet sich Wasser auf dem Boden. Die Schleuderphase ist ausgeschaltet. Stellen Sie das Schleuderprogramm ein. Der Filter der Ablaufpumpe ist zugesetzt.
www.aeg.com Problem Mögliche Ursache Mögliche Abhilfe Das Gerät verursacht ein ungewöhnliches Geräusch. Das Gerät ist nicht ausgerichtet. Richten Sie das Gerät waagrecht aus. Siehe hierzu „Montage“. Sie haben die Verpackungsmaterialien und/ oder die Transportschrauben nicht entfernt. Entfernen Sie die Verpackungsmaterialien und/oder die Transportschrauben. Siehe hierzu „Montage“. Es ist sehr wenig Wäsche in der Trommel. Füllen Sie mehr Wäsche ein.
DEUTSCH 31 13.2 Auspacken 1. Verwenden Sie Handschuhe. Entfernen Sie die äußere Folie. Benutzen Sie, falls erforderlich, ein Teppichmesser. 2. Nehmen Sie die Karton-Abdeckung ab. Entfernen Sie die Styropor-Verpackungsteile. 3. 4. Entfernen Sie die innere Folie. 5. Öffnen Sie die Tür. Entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel.
www.aeg.com 6. Legen Sie eines der Styroporverpackungsteile hinter dem Gerät auf den Boden. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 8. 1 2 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. 10. Lösen Sie die drei Schrauben.
DEUTSCH 33 12. Setzen Sie die Kunststoffkappen in die Öffnungen. Diese Kappen finden Sie im Beutel mit der Gebrauchsanleitung. WARNUNG! Entfernen Sie vor der Montage des Geräts alle Verpackungsmaterialien und Transportschrauben. Wir empfehlen, Verpackungsmaterial und Transportschrauben für einen späteren Transport aufzubewahren. 13.3 Aufstellen und Ausrichten x4 • Stellen Sie das Gerät auf einen ebenen, festen Boden.
www.aeg.com 13.4 Wasserzulaufschlauch • Schließen Sie den Schlauch am Gerät an. Drehen Sie den Wasserzulaufschlauch nur nach links oder rechts. Lösen Sie die Ringmutter, um ihn in die gewünschte Position zu bewegen. 20 O 45 O • Schließen Sie den Wasserzulaufschlauch an einen Kaltwasserhahn mit einem 3/4"-Außengewinde an. VORSICHT! Achten Sie darauf, dass die Anschlüsse dicht sind. Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist.
DEUTSCH 35 13.5 Wasserablauf Es gibt mehrere Möglichkeiten, den Ablaufschlauch anzuschließen: Mit der Kunststoff-Schlauchführung. • Über eine Waschbeckenkante. • Stellen Sie sicher, dass die KunststoffFührung beim Abpumpen nicht abrutschen kann. Befestigen Sie deswegen die Führung am Wasserhahn oder an der Wand. • An ein Standrohr mit Entlüftungsöffnung. Orientieren Sie sich an der Abbildung. Direkte Einleitung in ein Ablaufrohr auf einer Höhe nicht unter 60 cm und nicht über 100 cm.
www.aeg.com • Direkte Einleitung in ein Abflussrohr in der Zimmerwand. Mit einer Schlauchschelle befestigen. Sie können den Ablaufschlauch auf maximal 400 cm verlängern. Fragen Sie beim Kundendienst nach einem anderen Ablaufschlauch und der Schlauchverlängerung. 14. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte.
DEUTSCH 37
www.aeg.
DEUTSCH 39
132927651-A-522012 www.aeg.