L 87695 WD EN User manual
www.aeg.com CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . .
ENGLISH 3 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. 2.
ENGLISH Water connection • Make sure not to cause damage to the water hoses. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. 2.2 Use WARNING! Risk of injury, electrical shock, fire, burns or damage to the appliance.
www.aeg.com • Disconnect the appliance from the mains supply. • Cut off the mains cable and discard it. • Remove the door catch to prevent children and pets to get closed in the appliance. 3.
ENGLISH 4. PRODUCT DESCRIPTION 1 2 3 8 9 10 4 5 11 6 12 7 1 Worktop 7 Feet for the appliance level 2 Detergent dispenser 8 Water drain hose 3 Control panel 4 Door handle 9 Water inlet valve 10 Mains cable 5 Rating plate 11 Transit bolts 6 Drain pump 12 Feet for the appliance level 4.1 Accessories 1 4 2 3 4.2 Child safety device • When you activate this device, you cannot close the door. This prevents children or pets to be closed in the drum.
www.aeg.com 5. CONTROL PANEL 1 2 3 ECO 4 SUPER ECO Non Stop 60 Min. 5 20 Min. - 3 kg / On/Off 12 1 On/Off button (On/Off) 2 Programme knob 3 Display 11 10 9 4 Automatic drying button 5 Drying time button 6 Start Pause button 7 Delay start button 8 Time saving button 9 Extra rinse button 8 7 6 Stain/Prewash button: 10 Stain Prewash 11 Spin reduction button 12 Temperature button 5.1 On Off button 1 Press this button to activate or deactivate the appliance.
ENGLISH • After 5 minutes from the end of the washing programme. Refer to 'At the end of programme'. 9 5.2 Programme knob 2 Turn this knob to set a programme. The related programme indicator comes on. 5.3 Display 3 A B C P D E O F G H I N J M K L The display shows: The temperature of the set programme A Cold water The spin speed of the set programme B No Spin symbol1) Rinse Hold symbol 1) Only available for SPIN/DRAIN programme.
www.aeg.com E The steam symbol comes on when you set a Steam programme. F The anti-crease symbol comes on when you set a drying programme. You cannot open the appliance door when the symbol is on. You can open the door only when the symbol goes off. G If the programme is completed but the symbol stays on: • The 'Rinse Hold' function is on. • There is water in the drum. H The child safety lock symbol comes on when this device is activated.
ENGLISH 11 The detergent overdosing symbol comes on at the end of the cycle when the appliance detects too much detergent. M Graphic bars The empty indicator bar appears only if the related function is available for the set programme. The indicator bar fills accordingly to the set functions. If you make a wrong selection the message Err indicates that the selection is not possible. The time save symbol comes on when you set one of the programme duration.
www.aeg.com 5.8 Time save button 8 Press button 8 to decrease the duration of the programme. – Press one time to set 'Shortened duration' for items with daily soil. – Press two times to set 'Extra Quick' for items with light soil. Some programmes accept only one of the two functions. 5.9 Extra rinse button 9 Press button 9 to add rinsing phases to a programme. Use this function for persons allergic to detergents and in areas where the water is soft. 5.
ENGLISH 5.15 Permanent extra rinse function With this function you can keep the extra rinse function permanently on when you set a new programme. • To activate the function press button 8 and button 7 at the same time . until the display shows the symbol • To deactivate the function press button 8 and button 7 at the same time until the symbol goes off. 6. PROGRAMMES Programme Temperature Type of load Max.
www.aeg.com Programme Temperature Type of load Max. weight of load 20 Min. - 3 kg Quick wash of sport items 40° - 30° or cotton and synthetic items , lightly soiled or worn once. max. load 3 kg Rinses Cold All fabrics. max. load 9 kg All fabrics. The spin phase assumes the setting for cotton items. Set the spin speed Spin / Drain6) according the type fabrics. max.
ENGLISH Programme Temperature Type of load Max. weight of load Cycle description Functions ECO8) 60° - 40° White and fast coloured cotton with normal soil. Set this programme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended. max. load 9 kg Wash Rinses Long spin SPIN REDUCTION RINSE HOLD PREWASH1) / STAINS2) EXTRA RINSE TIME SAVE3) 15 1) If you use liquid detergent, set a programme without PREWASH.
www.aeg.com 6.1 Woolmark certificate • The wool wash of this machine has been tested and approved by The Woolmark Company for the washing of wool containing garments labelled as «hand wash» provided that the garments are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine. M1144 • The wool drying cycle of this machine has been tested and approved by The Woolmark Company.
ENGLISH 17 6.3 Programmes for timed drying Degree of drying Type of fabric Extra dry Cotton and linen For towelling mate- (bathrobes, bath towels, rials etc) Cupboard dry1) For items to put away Cotton and linen (bathrobes, bath towels, etc) Cupboard dry For items to put away Synthetics and mixed fabrics (jumpers, blouses, underwear, household linen) Iron dry Suitable for ironing Wool dry Cotton and linen (sheets, tablecloths, shirts, etc.
www.aeg.com Programme Energy consumption (KWh) Water consumption (litres) White Cottons 95° 2.5 73 Cottons 60° 1.60 69 Cotton Energy Saving Programme 60° 1) 1.05 63 Cottons 40° 1.0 69 Synthetics 40° 0.60 48 Delicates 40° 0.70 58 Wool/ Handwash 30° 0.35 57 Programme duration (minutes) For the duration of the programmes, please refer to the display on the control panel.
ENGLISH 19 Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. 9.2 Filling the detergent and additives The detergent compartment for the prewash phase, the soak programme and for the stain function. Add the detergent for prewash, soak and stain remover before the start of the programme. The detergent compartment for the washing phase. If you use a liquid detergent, put it immediately before you start the programme.
www.aeg.com Check the position of the flap 1. Pull out the detergent dispenser until it stops. 2. Press the lever down to remove the dispenser. 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6.
ENGLISH 6. When the countdown is completed, the programme starts automatically. Press button 6 to start the programme. The indicator of button 6 is on. Before you press button 6 to start the appliance, you can cancel or change the set of the delay start. You cannot set the delay start with the Steam programme. The drain pump can operate for a short time when the appliance fills water.
www.aeg.com • The door lock symbol goes off. • Press button 1 to deactivate the appliance. After five minutes from the end of the programme, the energy saving function automatically deactivates the appliance. – The door stays locked. – You must drain the water to open the door. When you activate the appliance again, the display show the end of the last set programme. Turn the programme knob to set a new cycle. • Remove the laundry from the appliance. Make sure that the drum is empty.
ENGLISH 23 The drying symbol starts to flash. The door locked symbol comes on. The symbol of the set level stays on. The other level symbols go off. If you set the time value of only 10 minutes, the appliance performs only a cooling phase. You cannot set all levels for all kind of laundry. With the timed drying: • Press the button 5 again and again to set the time value (see the «Drying Programme» table). The drying symbol comes on. At the end of the programme • The appliance stops automatically.
www.aeg.com CAUTION! Do not set a spin speed lower than the automatic speed of the set programme. • Set the available options. • Press the button 8 until the black line appears under one of the dryness level symbol. The iron dry level comes on The cupboard dry level comes on. The extra dry level comes on. The drying symbol comes on. The anti-crease symbol comes on. The time value on the display is the duration of the washing + drying cycles calculated on a default load size.
ENGLISH • When the programme is completed, the appliance stops automatically. • The acoustic signals operate. • When the door locked symbol goes off, you can open the door. • Remove the laundry from the appliance. Make sure that the drum is empty. • Close the water tap. • Keep the door ajar, to prevent mildew and odours. 11.3 Fluff in the fabrics During the washing and/or drying phase, some types of fabric, (sponge, wool, sweatshirt) could release fluff.
www.aeg.com • Do not mix different types of detergents. • To help the environment, do not use more than the correct quantity of detergent. • Obey the instructions that you find on the on packaging of these products. • Use the correct products for the type and colour of the fabric, the programme temperature and the level of soil. • If you use liquid detergents, do not set the prewash phase.
ENGLISH – Fabrics with residue of hair sprays, nail solvents or similar. – Garments with foam-rubber or materials similar to foam-rubber. 27 • = The drying cycle is at high temperature • = The drying cycle is at reduced temperature • weight of the load size GENERAL TIPS Refer to the «Drying programmes» table to find the average drying times. The experience will help you to dry the laundry in a more correct way. Take note of the duration drying time of the cycles done before.
www.aeg.com 13.4 Door seal Regularly examine the seal and remove all objects from the inner part. 13.5 Drum Regularly examine the drum to prevent limescale and rust particles. Only use special products to remove rust particles from the drum. To do this: • Clean the drum with special product for stainless steel. • Start a short programme for cotton at the maximum temperature with a small quantity of detergent. 13.6 Detergent dispenser To clean the dispenser: 1 1. 2. Press the lever.
ENGLISH 13.7 Drain pump Regularly examine the drain pump and make sure that it is clean. 29 • The display shows an alarm code because of the problem with water drain. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates. Do not clean the drain pump if the water in the appliance is hot. The water must be cold before you clean the drain pump. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn.
www.aeg.com 2 1 13.8 The inlet hose filter and the valve filter 7. Remove fluff and objects from the pump. 8. Make sure that the impeller of the pump can turn. If this does not occur, contact the service centre. 9. Clean the filter under the water tap and put it back in the pump into the special guides. 10. Make sure that you tighten correctly the filter to prevent leakages. 11. Put the flap back and close the drain pump door.
ENGLISH 4. 5. 6. 7. 20° 31 Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 45° 13.9 Emergency drain Because of a malfunction, the appliance cannot drain the water. If this occurs, do steps (1) through (6) of 'To clean the drain pump'. If necessary, clean the pump. Put the drainage duct back and close the drain pump flap.
www.aeg.com • • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. - The anti-flood device is on. WARNING! Deactivate the appliance before you do the checks. Problem Possible cause Possible solution The appliance does not fill with water. The water tap is closed. Open the water tap. The water inlet hose is damaged. Make sure that the water inlet hose has no damages. The filters in the water inlet hose is blocked . Clean the filters.
ENGLISH Problem The programme does not start. There is water on the floor. 33 Possible cause Possible solution The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again. The mains plug is not connected in the mains socket. Put in the mains plug. Blow out fuse in the household fuse box. Replace the fuse. You did not press button 6 .
www.aeg.com Problem The appliance does not dry or does not dry correctly. The laundry is full of different colours fluff. Possible cause Possible solution You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains. Incorrect temperature was set. Make sure that you set the correct temperature. Too much laundry load. Decrease the laundry load. The water tap is not turned on. Turn the tap on. The drain filter is clogged.
ENGLISH 35 15.2 Unpacking 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum.
www.aeg.com 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 8. 1 2 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers.
ENGLISH 37 12. Put the plastic caps in the holes. You can find these caps in the user manual bag. WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance. 15.3 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance.
www.aeg.com 15.4 The inlet hose • Connect the hose to the appliance. Turn the inlet hose only left or right. Loose the ring nut to set it in the correct position. 20 O 45 O • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device.
ENGLISH 39 With the plastic hose guide. • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose.
www.aeg.com You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension. 16. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste.
ENGLISH 41
www.aeg.
ENGLISH 43
132924361-B-202013 www.aeg.