L 87695 WDP EN User manual
www.aeg.com CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . .
ENGLISH 3 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. 2.
ENGLISH Water connection • Make sure not to cause damage to the water hoses. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. 2.2 Use WARNING! Risk of injury, electrical shock, fire, burns or damage to the appliance.
www.aeg.com • Disconnect the appliance from the mains supply. • Cut off the mains cable and discard it. • Remove the door catch to prevent children and pets to get closed in the appliance. 3.
ENGLISH 4. PRODUCT DESCRIPTION 1 2 3 8 9 10 4 5 11 6 12 7 1 Worktop 7 Feet for the appliance level 2 Detergent dispenser 8 Water drain hose 3 Control panel 4 Door handle 9 Water inlet valve 10 Mains cable 5 Rating plate 11 Transit bolts 6 Drain pump 12 Feet for the appliance level 4.1 Accessories 1 4 2 3 4.2 Child safety device • When you activate this device, you cannot close the door. This prevents children or pets to be closed in the drum.
www.aeg.com 5. CONTROL PANEL 1 2 3 Ochrona Bawelniane Odswiezanie Syntetyczne Ekonomiczne Latwe Prasowanie Super Eko Non Stop 60 Min. Bawelniane Delikatne Wełniane/ Jedwabne 20 Min. - 3 kg Syntetyczne Plukanie Wirowanie/ Odpompowanie Wełniane On/Off Opóźniony Plamy/ Temp.
ENGLISH 9 5.3 Display 3 A B C P D E O F G H I N J M K L The display shows: The temperature of the set programme A Cold water The spin speed of the set programme B No Spin symbol1) Rinse Hold symbol 1) Only available for SPIN/DRAIN programme. Prewash phase Washing phase Rinses phase Spin phase C The phase symbols • When a programme is set, all the symbols of the phases related to the programme come on. • When the programme starts, only the symbol of the phase in operation flashes.
www.aeg.com F The anti-crease symbol comes on when you set a drying programme. You cannot open the appliance door when the symbol is on. You can open the door only when the symbol goes off. G If the programme is completed but the symbol stays on: • The 'Rinse Hold' function is on. • There is water in the drum. H The child safety lock symbol comes on when this device is activated. I The delay start symbol comes on when you set the delay start function.
ENGLISH 11 Graphic bars The empty indicator bar appears only if the related function is available for the set programme. The indicator bar fills accordingly to the set functions. If you make a wrong selection the message Err indicates that the selection is not possible. The time save symbol comes on when you set one of the programme duration. N • Shortened time • Extra Quick The extra rinse symbol comes on when this function is activated. O The value shows the total number of the rinses.
www.aeg.com – Press two times to set 'Extra Quick' for items with light soil. Some programmes accept only one of the two functions. 5.9 Extra rinse button 9 Press button 9 to add rinsing phases to a programme. Use this function for persons allergic to detergents and in areas where the water is soft. 5.10 The Stain-Prewash button 10 Press button 10 to add the stain and/or a prewash phase to a programme. Press the button again and again to activate one or two options.
ENGLISH • To activate the function press button 8 and button 7 at the same time until the display shows the symbol . 13 • To deactivate the function press button 8 and button 7 at the same time until the symbol goes off. 6. PROGRAMMES Programme Temperature Type of load Cycle descripMax. weight of load tion Functions WASHING PROGRAMMES Bawełniane 95° - Cold White and coloured cotton with heavy level of soil. max.
www.aeg.com Programme Temperature Type of load Cycle descripMax. weight of load tion Functions 20 Min. - 3 kg 40° - 30° Quick wash of sport items or cotton and synthetic items , lightly soiled or worn once. max. load 3 kg Wash Rinses Short spin SPIN REDUCTION Płukanie Cold All fabrics. max. load 9 kg One rinse with additive spin phase SPIN REDUCTION RINSE HOLD EXTRA RINSE5) Wirowanie / Odpompowanie6) All fabrics.
ENGLISH 15 Programme Temperature Type of load Cycle descripMax. weight of load tion Functions Ekonomiczne8) 60° - 40° White and fast colWash oured cotton with Rinses normal soil. Long spin Set this programme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended. max. load 9 kg SPIN REDUCTION RINSE HOLD PREWASH1) / STAINS2) EXTRA RINSE TIME SAVE3) 1) If you use liquid detergent, set a programme without PREWASH.
www.aeg.com 1) If you set a Steam programme with dried laundry, at the end of the cycle the laundry feels humid. It is better to expose items to the open air for about 10 minutes to remove the humidity. When the programme is completed, quickly remove the laundry from the drum. After a steam cycle, items may to be ironed anyway, but with less effort! 6.
ENGLISH 17 6.3 Programmes for timed drying Degree of drying Type of fabric Extra dry Cotton and linen For towelling mate- (bathrobes, bath towels, rials etc) Cupboard dry1) For items to put away Cotton and linen (bathrobes, bath towels, etc) Cupboard dry For items to put away Synthetics and mixed fabrics (jumpers, blouses, underwear, household linen) Iron dry Suitable for ironing Wool dry Cotton and linen (sheets, tablecloths, shirts, etc.
www.aeg.com Programme Energy consumption (KWh) Water consumption (litres) Cottons 60° 1.60 69 Cotton Energy Saving Programme 60° 1) 1.05 61 Cottons 40° 1.0 69 Synthetics 40° 0.60 48 Delicates 40° 0.70 58 Wool/ Handwash 30° 0.35 57 Programme duration (minutes) For the duration of the programmes, please refer to the display on the control panel.
ENGLISH 19 Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. 9.2 Filling the detergent and additives The detergent compartment for the prewash phase, the soak programme and for the stain function. Add the detergent for prewash, soak and stain remover before the start of the programme. The detergent compartment for the washing phase. If you use a liquid detergent, put it immediately before you start the programme.
www.aeg.com Check the position of the flap 1. Pull out the detergent dispenser until it stops. 2. Press the lever down to remove the dispenser. 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6.
ENGLISH 6. When the countdown is completed, the programme starts automatically. Press button 6 to start the programme. The indicator of button 6 is on. Before you press button 6 to start the appliance, you can cancel or change the set of the delay start. You cannot set the delay start with the Steam programme. The drain pump can operate for a short time when the appliance fills water.
www.aeg.com • The door lock symbol goes off. • Press button 1 to deactivate the appliance. After five minutes from the end of the programme, the energy saving function automatically deactivates the appliance. – The door stays locked. – You must drain the water to open the door. When you activate the appliance again, the display show the end of the last set programme. Turn the programme knob to set a new cycle. • Remove the laundry from the appliance. Make sure that the drum is empty.
ENGLISH 23 The door locked symbol comes on. The drying symbol starts to flash. The drying symbol starts to flash. The door locked symbol comes on. The symbol of the set level stays on. The other level symbols go off. If you set the time value of only 10 minutes, the appliance performs only a cooling phase. You cannot set all levels for all kind of laundry. With the timed drying: • Press the button 5 again and again to set the time value (see the «Drying Programme» table).
www.aeg.com CAUTION! Do not set a spin speed lower than the automatic speed of the set programme. • Set the available options. • Press the button 4 until the black line appears under one of the dryness level symbol. The iron dry level comes on The cupboard dry level comes on. The extra dry level comes on. The drying symbol comes on. The anti-crease symbol comes on. The time value on the display is the duration of the washing + drying cycles calculated on a default load size.
ENGLISH • When the programme is completed, the appliance stops automatically. • The acoustic signals operate. • When the door locked symbol goes off, you can open the door. • Remove the laundry from the appliance. Make sure that the drum is empty. • Close the water tap. • Keep the door ajar, to prevent mildew and odours. 11.3 Fluff in the fabrics During the washing and/or drying phase, some types of fabric, (sponge, wool, sweatshirt) could release fluff.
www.aeg.com • Do not mix different types of detergents. • To help the environment, do not use more than the correct quantity of detergent. • Obey the instructions that you find on the on packaging of these products. • Use the correct products for the type and colour of the fabric, the programme temperature and the level of soil. • If you use liquid detergents, do not set the prewash phase.
ENGLISH 12.8 Drying cycle duration The drying time can change depending on: • speed of the last spin • dryness level • type of laundry • weight of the load size GENERAL TIPS Refer to the «Drying programmes» table to find the average drying times. The experience will help you to dry the laundry in a more correct way. Take note of the duration drying time of the cycles done before. To avoid the static charge at the end of the drying cycle: 27 • Use fabric conditioner in the washing cycle.
www.aeg.com 13.5 Drum Regularly examine the drum to prevent limescale and rust particles. Only use special products to remove rust particles from the drum. To do this: • Clean the drum with special product for stainless steel. • Start a short programme for cotton at the maximum temperature with a small quantity of detergent. 13.6 Detergent dispenser To clean the dispenser: 1 1. 2. Press the lever. Pull the dispenser out. 3. Remove the top part of the liquid additive compartment.
ENGLISH 29 To clean the drain pump: 1. Open the drain pump door. 2. Pull the flap out to remove it. 3. Put a container below the recess of the drain pump to collect the water that flows out. Press the two levers and pull forward the drainage duct to let the water flow out. 4. 1 5. 6. When the container is full of water, put the drainage duct back again and empty the container. Do steps 4 and 5 again and again until no more water flows out from the drain pump.
www.aeg.com 9. Clean the filter under the water tap and put it back in the pump into the special guides. 10. Make sure that you tighten correctly the filter to prevent leakages. 11. Put the flap back and close the drain pump door. 2 1 13.8 The inlet hose filter and the valve filter • The indicator of button 6 flashes and the display shows the related alarm. Refer to 'Troubleshooting'. It could be necessary to clean the filters when: • The appliance does not fill with water.
ENGLISH Put the drainage duct back and close the drain pump flap. When you drain the water with the emergency drain procedure, you must activate again the drain system: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. 31 2. 3. 4. Close the water tap. Remove the water inlet hose Put the two ends of the inlet hose in a container and let the water flow out of the hose. 5. Empty the drain pump.
www.aeg.com Problem Possible cause The appliance The water drain hose is does not drain the damaged. water. Possible solution Make sure that the water drain hose has no damages. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. The connection of the water drain hose is not correct. Make sure that the connection is correct. A washing programme without the drain phase is set. Set the drain programme. The function Rinse & Hold is on.
ENGLISH Problem Possible cause 33 Possible solution Leakages from the drain Make sure that the drain pump pump. filter is tight. You cannot open the appliance door. The appliance makes an unusual noise. The water drain hose is damaged. Make sure that the water inlet hose has no damages. The washing programme is in operation. Let the washing programme end. There is water in the drum. Set the drain or the spin programme. Incorrect level of the ap- Adjust the level of the applipliance. ance.
www.aeg.com Problem Possible cause Possible solution If there is a big quantity of fluff in the drum repeat this procedure again and again: • Clean the empty drum, the gasket and the door with a wet cloth. • Set a rinse cycle • Put a wool or piled fabric cloth in the drum. • Set a drying cycle of 10 minutes • Remove the old wool cloth. After the check, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact the service centre.
ENGLISH 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 8.
www.aeg.com 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. 12. Put the plastic caps in the holes. You can find these caps in the user manual bag. WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance.
ENGLISH 37 15.3 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. x4 • The appliance must be level and stable.
www.aeg.com • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault .
ENGLISH 39 • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose. Without the plastic hose guide.
www.aeg.com 16. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
ENGLISH 41
www.aeg.
ENGLISH 43
132924251-A-072013 www.aeg.
