DE Benutzerinformation Waschmaschine L 89499 FL2 L 89498 FL2
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................... 4 3. GERÄTEBESCHREIBUNG...............................................................................................6 4. BEDIENFELD................................................................................................................... 7 5.
DEUTSCH 1. 3 SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.
www.aeg.com • • • • • • • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnungen im Gerätesockel (falls vorhanden) dürfen nicht von einem Teppichboden blockiert werden. Das Gerät muss mit den mitgelieferten neuen Schläuchen an die Wasserversorgung angeschlossen werden. Alte Schläuche dürfen nicht wieder verwendet werden.
DEUTSCH • Stellen Sie das Gerät nicht an einem Ort auf, an dem die Tür nicht vollständig geöffnet werden kann. • Achten Sie darauf, dass beim ersten Gebrauch des Geräts keine Undichtheiten vorhanden sind. 2.2 Elektrischer Anschluss 2.4 Verwendung • Das Gerät muss geerdet sein. • Schließen Sie das Gerät nur an eine ordnungsgemäß installierte Schutzkontaktsteckdose an. • Stellen Sie sicher, dass die elektrischen Daten auf dem Typenschild den Daten Ihrer Stromversorgung entsprechen.
www.aeg.com 3. GERÄTEBESCHREIBUNG 3.1 Geräteübersicht 1 2 3 4 5 1 2 3 4 5 6 7 Arbeitsplatte Waschmittelschublade Bedienfeld Türgriff Typenschild Filter der Ablaufpumpe Schraubfüße zum Ausrichten des Geräts 6 7 3.2 Einschalten der Kindersicherung Diese Vorrichtung sorgt dafür, dass Kinder oder Haustiere nicht in der Trommel eingeschlossen werden können. Drehen Sie die Vorrichtung im Uhrzeigersinn, bis sich die Einkerbung in waagerechter Lage befindet. Die Tür lässt sich nicht schließen.
DEUTSCH 4. BEDIENFELD 4.1 Bedienfeldbeschreibung 1 2 3 10 1 2 3 4 5 6 Taste Ein/Aus (Auto Off) Programmwahlschalter Display Taste Start/Pause (Start/Pause) Taste Zeitvorwahl (Zeitvorwahl) Taste Zeitsparen (Zeit Sparen) 9 8 7 6 5 4 7 Taste Extra Spülen (Extra Spülen) 8 Taste Flecken-/Vorwäsche (Flecken/ Vorwäsche) 9 Taste Schleuderdrehzahl (U./Min.) 10 Taste Temperatur (Temp.) 4.
www.aeg.com Schleuderdrehzahl des eingestellten Programms B Symbol Kein Schleudern1) Symbol Spülstopp 1) Nur verfügbar für das Programm Schleudern/Abpumpen. Symbole für die Waschgänge Wenn ein Programm eingestellt ist, leuchten alle Symbole für die Phasen des Programms auf. Beim Start des Programms blinkt nur das Symbol der aktuell laufenden Phase. Nach Ende des Programms leuchtet das Symbol der letzten Phase.
DEUTSCH 9 Programmdauer Wenn das Programm beginnt, verringert sich die angezeigte Zeit in Minutenschritten. Zeitvorwahl Wenn Sie die Zeitvorwahl-Taste drücken, zeigt das Display die verbleibende Zeit bis zum Programmstart an. Alarmcodes Bei einer Störung des Geräts erscheinen im Display Alarmcodes. Siehe hierzu „Fehlersuche“.
www.aeg.com Dieses Zeitsparsymbol leuchtet auf, wenn Sie die Programmdauer reduzieren. K Verkürzte Programmdauer Extra Kurz Das Symbol Extra Spülen erscheint, wenn diese Funktion eingeschaltet ist. L Die Zahl steht für die Gesamtzahl der Spülgänge. Der Anzeigebalken ist komplett gefüllt, wenn Sie die maximale Anzahl an Spülgängen einstellen. Das Fleckensymbol leuchtet beim Einschalten der Funktion auf. Das Symbol Vorwäsche erscheint, wenn diese Funktion eingeschaltet ist.
DEUTSCH 11 Programm Temperaturbereich Maximale Beladung Maximale Schleuderdrehzahl Programmbeschreibung (Beladung und Verschmutzungsgrad) Leichtbügeln 60 °C - Kalt 4 kg 800 U/min Pflegeleichte Textilien, die sanft gewaschen wer- Feinwäsche 40 °C - Kalt 4 kg 1200 U/min Feinwäsche aus Acryl, Viskose, Polyester. Normal verschmutzt. Daunen 60 °C - 30 °C 3 kg 800 U/min Spezialprogramm für eine Decke, Bettdecke, Tagesdecke usw. Anti-Allergie 60 °C 9 kg 1400 Weiße Baumwollwäsche.
www.aeg.com Programm Temperaturbereich Maximale Beladung Maximale Schleuderdrehzahl Programmbeschreibung (Beladung und Verschmutzungsgrad) Dampfprogramme4) Dampf kann für getrocknete, gewaschene oder einmal getragene Wäsche benutzt werden. Diese Programme können Falten und Gerüche reduzieren und machen Ihre Wäsche glatter. Verwenden Sie kein Waschmittel. Entfernen Sie Flecken bei Bedarf durch Waschen oder einen an der entsprechenden Stelle angewendeten Fleckentferner.
DEUTSCH 13 Mögliche Programmkombinationen Extra Leise Zeitvorwahl ■ Zeit Sparen 3) ■ Extra Spülen 2) Koch/Bunt Flecken/Vorwäsche 1) U./Min. Programm ■ ■ ■ ■ ■ ■ ■ ■ Pflegeleicht ■ ■ ■ ■ ■ ■ Leichtbügeln ■ ■ ■ 4) ■ ■ ■ Feinwäsche ■ ■ ■ ■ ■ ■ Daunen ■ Anti-Allergie ■ Schleudern/Pumpen5) ■ Spülen ■ ■ ■ Outdoor ■ ■ ■ 20 Min.
www.aeg.com 5.2 Woolmark Apparel Care Grün Woolmark auf das Waschen von Wolltextilien mit der Pflegekennzeichnung „Handwäsche“ getestet und zugelassen, vorausgesetzt, dass die Wäsche gemäß der Anleitung auf dem Kleidungsetikett und gemäß den Angaben des Maschinenherstellers gewaschen wird. Beachten Sie die Trocken- und Waschanleitung auf dem Kleidungsetikett. M1361 In Großbritannien, Irland, Hongkong und Indien ist das Woolmark-Symbol ein zertifiziertes Warenzeichen.
DEUTSCH Programme Beladung Energiever(kg) brauch (kWh) 15 Wasserverbrauch (Liter) Ungefähre Programmdauer (in Minuten) Restfeuchte (%)1) Standardprogramm Baumwolle 60 °C 9 0,64 57 226 52 Standardprogramm Baumwolle 60 °C 4.5 0,35 41 185 52 Standardprogramm Baumwolle 40 °C 4.5 0,35 40 199 52 1) Am Ende der Schleuderphase. 2) Für einige Modelle nicht verfügbar.
www.aeg.com Bei Wahl dieser Option geben Sie den Fleckentferner in das Fach . Mit dieser Funktion verlängert sich die Programmdauer. Diese Option ist bei Temperaturen unter 40 °C nicht verfügbar. • Vorwäsche: Wählen Sie diese Option, um vor dem Hauptwaschgang einen Vorwaschgang durchzuführen. Wir empfehlen Ihnen, diese Option zum Waschen von stark verschmutzter Wäsche zu verwenden. Durch das Einschalten dieser Option verlängert sich die Programmdauer. 7.6 U./Min.
DEUTSCH 17 9. REINIGEN SIE VOR DEM ERSTEN GEBRAUCH 1. Geben Sie 2 Liter Wasser in das Waschmittelfach für die Hauptwäsche. Dadurch wird das Abpumpsystem aktiviert. 2. Geben Sie eine kleine Waschmittelmenge in das Waschmittelfach für die Hauptwäsche. 3. Stellen Sie ein Koch-/BuntwäscheProgramm mit der höchsten Temperatur ein und starten Sie das Programm mit leerer Trommel. So werden alle eventuellen Verunreinigungen aus Trommel und Bottich entfernt. 10.
www.aeg.com Wenn das Gewicht der Wäsche die Höchstbeladung der Trommel überschreitet, beginnen das Symbole und der Wert zu blinken. Sie können die Wäsche waschen, jedoch bei erhöhtem Wasser- und Energieverbrauch. Für optimale Verbrauchswerte und Waschergebnisse sollten Sie einige Wäschestücke entfernen, bis die Symbole nicht mehr blinken. Die Anzeige für Überladung ist nur für Programme verfügbar, deren erlaubte Beladung niedriger ist als die Höchstbeladung der Maschine. 3. Schließen Sie die Tür.
DEUTSCH 1 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. A 19 Klappe in der unteren Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. • Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. • Stellen Sie nicht den Vorwaschgang ein. • Stellen Sie nicht die Zeitvorwahl ein. 5. Messen Sie Waschmittel und Weichspüler ab. 6. Schließen Sie die Waschmittelschublade vorsichtig.
www.aeg.com 10.9 Abbrechen der Zeitvorwahl Abbrechen der Zeitvorwahl: 1. Drücken Sie die Taste Start/Pause, um die Maschine in den Pausenmodus zu schalten. Die zugehörige Kontrolllampe blinkt. 2. Drücken Sie die Taste Zeitvorwahl wiederholt, bis im Display angezeigt wird. 3. Drücken Sie die Taste Start/Pause erneut, um das Programm sofort zu starten. 10.
DEUTSCH Wenn Sie das Gerät wieder einschalten, sehen Sie im Display das Ende des letzten Programms. Drehen Sie den Programmwahlschalter, um ein neues Programm einzustellen. 2. Nehmen Sie die Wäsche aus dem Gerät. 3. Vergewissern Sie sich, dass die Trommel leer ist. 4. Lassen Sie die Tür offen, damit sich kein Schimmel und keine unangenehmen Gerüche bilden. 10.
www.aeg.com • Waschen Sie keine ungesäumten Wäschestücke und Wäschestücke mit Schnitten im Stoff in der Maschine. Waschen Sie kleine und/oder empfindliche Wäschestücke, wie Bügel-BHs, Gürtel, Strumpfhosen usw., in einem Wäschenetz. • Eine sehr geringe Beladung kann in der Schleuderphase Probleme verursachen. Verteilen Sie die Wäschestücke in diesem Fall mit der Hand neu und starten Sie die Schleuderphase erneut. 11.2 Hartnäckige Flecken Für manche Flecken sind Wasser und Waschmittel nicht ausreichend.
DEUTSCH 23 • Starten Sie ein Programm für Koch-/ Buntwäsche mit der maximalen Temperatur und einer kleinen Menge Waschmittel. ACHTUNG! Verwenden Sie keinen Alkohol, keine Lösungsmittel und keine Chemikalien. 12.4 Türdichtung 12.2 Entkalken Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Entkalkers für Waschmaschinen. Überprüfen Sie regelmäßig, dass sich kein Kalk und keine Rostpartikel in der Trommel absetzen.
www.aeg.com 3. 4. 12.7 Reinigen des Ablauffilters WARNUNG! Reinigen Sie den Ablauffilter nicht, wenn das Wasser im Gerät heiß ist. 1. 2. 2 1 1 2 1 3. 4.
DEUTSCH 5. 6. 1 2 7. 8. 1 2 9.
www.aeg.com 12.8 Reinigen des Zulaufschlauchs und Ventilfilters 1. 2. 1 2 3 3. 4. 45° 20° 12.9 Notentleerung 12.10 Frostschutzmaßnahmen Das Gerät kann aufgrund einer Funktionsstörung das Wasser nicht abpumpen. Falls das Gerät in einem Bereich installiert ist, in dem die Temperatur unter 0 °C sinken kann, entfernen Sie das im Zulaufschlauch und in der Ablaufpumpe verbliebene Wasser. In diesem Fall führen Sie die Schritte (1) bis (9) unter „Reinigen des Ablauffilters“ durch.
DEUTSCH 27 WARNUNG! Stellen Sie sicher, dass die Temperatur über 0 °C liegt, bevor Sie das Gerät wieder einschalten. Der Hersteller ist nicht für Schäden verantwortlich, die auf zu niedrige Temperaturen zurückzuführen sind. 13. FEHLERSUCHE WARNUNG! Siehe Kapitel Sicherheitshinweise. 13.1 Einleitung Das Gerät startet nicht oder stoppt während des Betriebs. Versuchen Sie zunächst selbst eine Lösung für das Problem zu finden (siehe Tabelle).
www.aeg.com Problem Mögliche Abhilfe Der Wassereinlauf in das Gerät funktioniert nicht ordnungsgemäß. Vergewissern Sie sich, dass der Wasserzulauf geöffnet ist. Vergewissern Sie sich, dass der Wasserdruck der Wasserversorgung nicht zu niedrig ist. Diese Information erhalten Sie von Ihrem Wasserversorger. Vergewissern Sie sich, dass der Wasserzulauf nicht verstopft ist. Überzeugen Sie sich, dass der Filter des Zulaufschlauchs und der Filter des Ventils nicht verstopft sind.
DEUTSCH 29 Problem Mögliche Abhilfe Es befindet sich Wasser auf dem Boden. Vergewissern Sie sich, dass alle Wasseranschlüsse vollkommen dicht sind, sodass kein Wasser austreten kann. Vergewissern Sie sich, dass der Wasserablaufschlauch keine Beschädigungen aufweist. Verwenden Sie ein geeignetes Waschmittel in der richtigen Menge. Die Tür des Geräts lässt sich nicht öffnen. Vergewissern Sie sich, dass das Waschprogramm beendet ist.
www.aeg.com Problem Mögliche Abhilfe Die Trommel ist leer und im Display wird angezeigt, dass sich Wäsche darin befindet. Schalten Sie das Gerät mit der Taste Auto Off aus und wieder ein, um das Leergewicht einzustellen. Die Trommel ist voll, im Display wird jedoch 0.0 kg angezeigt. Sie haben die Wäsche eingefüllt, bevor das Gerät eingeschaltet wurde. Drücken Sie die Taste Auto Off, um das Gerät auszuschalten. Leeren Sie die Trommel und befolgen Sie die notwendigen Schritte.
DEUTSCH 31 14. TECHNISCHE DATEN Abmessungen Breite/Höhe/Tiefe/ Gesamttiefe 600 mm/850 mm/605 mm/639 mm Elektrischer Anschluss Spannung Gesamtleistung Sicherung Frequenz 230 V 2200 W 10 A 50 Hz Die Schutzverkleidung gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt.
132902510-A-482014 www.aeg.