L8FE74488 USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................4 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 10 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com • • • • • • • • • Überschreiten Sie nicht die maximale Beladungsmenge von 8 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • Halten Sie sich an die mitgelieferte Montageanleitung. • Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist. • Der Boden, auf dem das Gerät aufgestellt werden soll, muss eben, stabil, hitzebeständig und sauber sein. • Stellen Sie sicher, dass die Luft zwischen dem Gerät und dem Boden zirkulieren kann.
www.aeg.com 2.5 Service • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. 2.6 Entsorgung WARNUNG! Verletzungs- und Erstickungsgefahr. • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung. • Schneiden Sie das Netzkabel in der Nähe des Geräts ab, und entsorgen Sie es. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in der Trommel einschließen.
DEUTSCH 7 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 10. Lösen Sie die drei Schrauben mit dem mitgelieferten Schraubenschlüssel. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 1 2 8. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. Aus dem Ablaufschlauch könnte Wasser austreten.
www.aeg.com Stellen Sie sicher, dass die Luftzirkulation unter dem Gerät nicht durch Teppiche beeinträchtigt wird. Vergewissern Sie sich, dass das Gerät weder die Wand noch andere Geräte berührt. 2. Schrauben Sie die Füße zum Ausrichten des Geräts weiter heraus oder hinein. 3.3 Wasserzulaufschlauch 1. Schließen Sie den Wasserzulaufschlauch an der Rückseite der Maschine an. 2. Drehen Sie ihn nach links oder rechts, je nach Position des Wasserhahns.
DEUTSCH Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist. Wenden Sie sich an den Kundendienst, um einen anderen Zulaufschlauch zu erhalten. 9 Stellen Sie sicher, dass die Kunststoffführung beim Abpumpen nicht herausrutschen kann. 3.4 Aquastop-Vorrichtung Der Zulaufschlauch verfügt über eine Aquastop-Vorrichtung. Diese Vorrichtung verhindert Wasserlecks am Schlauch, die durch natürliche Alterung auftreten können. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an.
www.aeg.com Stellen Sie sicher, dass der Ablaufschlauch einen Bogen beschreibt, damit keine Partikel aus dem Becken in das Gerät gelangen können. 6. Stecken Sie den Schlauch direkt in ein Abflussrohr in der Zimmerwand und befestigen Sie ihn mit einer Schlauchschelle. 5. Ohne Kunststoffschlauchführung: Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Orientieren Sie sich an der Abbildung. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
DEUTSCH 11 4.2 Geräteübersicht 1 2 9 8 3 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Arbeitsplatte Waschmittelschublade Bedienfeld Türgriff Typenschild Filter der Ablaufpumpe Füße für die Ausrichtung des Geräts 8 9 10 11 12 Ablaufschlauch Anschluss des Zulaufschlauchs Netzkabel Transportschrauben Schlauchhalter 5. BEDIENFELD 5.
www.aeg.com 1 Programmwahlschalter 2 Display 3 Sensortaste Eco (Eco) 4 Sensortaste Zeit Sparen (Zeit Sparen) 5 Sensortaste Spülen (Spülen) • Option Extra Spülen (Extra Spülen) • Waschprogramm überspringen Option Nur Spülen (Nur Spülen) 6 Sensortaste Start/Pause (Start/Pause) 7 Sensortaste Flecken/Vorwäsche (Flecken/Vorw.) • Option Flecken (Flecken) • Option Vorwäsche (Vorwäsche) 8 Sensortaste Zeitvorwahl (Zeitvorwahl) 9 Sensortaste Plus Dampf (Plus Dampf) 10 Sensortaste Drehzahlreduzierung (U./ Min.
DEUTSCH 13 Die Digitalanzeige zeigt Folgendes an: ). • Programmdauer (z.B. • Zeitvorwahl (z.B. oder ). • Programmende ( ). • Fehlercode (z. B. ). Kontrolllampe Hauptspülgang. Blinkt während der Vorwasch- und Hauptwaschphase. Kontrolllampe Spülphase. Blinkt während der Spülphase. Wenn die Option Soft Plus eingeschaltet ist, erscheint die Anzeige . Schleuder- und Abpumpphasenanzeige. Blinkt während der Schleuderund Abpumpphase. MIX Anzeige OKO-Mix. Dampfphasenanzeige. Knitterschutzphasenanzeige.
www.aeg.com 6.2 Einführung Auf dem Display erscheint die Die Optionen/Funktionen lassen sich nicht zusammen mit allen Waschprogrammen auswählen. Prüfen Sie die Kompatibilität der Optionen/Funktionen mit den Waschprogrammen in der „Programmübersicht“. Eine Option/Funktion kann eine andere ausschließen. In diesem Fall ist es nicht möglich, die inkompatiblen Optionen/Funktionen zusammen auszuwählen. 6.3 Temp.
DEUTSCH Das Gerät führt nur den Schleudergang des gewählten Programms aus. Die Dampfphase vermindert die Knitterbildung und erleichtert das Bügeln. Auf dem Display wird Während der Dampfphase blinkt die (kalt), die Programmphase und die Schleuderdrehzahl angezeigt. Wünschen Sie eine niedrigere Schleuderdrehzahl, so wählen Sie ein Programm mit niedrigerer Drehzahl aus. 6.5 Flecken/Vorw. Drücken Sie diese Taste mehrmals, um eine der beiden Optionen einzuschalten.
www.aeg.com Mit dieser Option verlängert sich die Programmdauer leicht. • Waschprogramm überspringen Option Nur Spülen Das Gerät führt nur den Spül-, Schleuder- und Abpumpgang des ausgewählten Programms durch. Die jeweilige Kontrollleuchte über den Sensortasten leuchtet auf. 6.10 Eco Wählen Sie diese Option für leicht oder normal verschmutzte Wäsche, die bei 30 °C oder höheren Temperaturen gewaschen werden soll.
DEUTSCH 17 Programm Programmbeschreibung Baumwolle Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte. Das Programm Baumwolle bei 60 °C und das Programm Baumwolle bei 40 °C mit der Option sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“.
www.aeg.com Programm Anti-Allergie 20 min. - 3 kg Outdoor Programmbeschreibung Weiße Baumwollwäsche. Dieses Programm beseitigt Mikroorganismen durch einen Waschgang, bei dem die Temperatur für einige Minuten auf über 60 °C gehalten wird. So werden Keime, Bakterien, Mikroorganismen und Partikel entfernt. Ein zusätzlicher Spülgang sorgt dafür, dass Waschmittelrückstände und Pollen/Allergene beseitigt werden. Auf diese Weise wird die Reinigung effektiver.
DEUTSCH 19 Programmtemperatur, maximale Schleuderdrehzahl und maximale Beladung Programm Standardtemperatur Temperaturbereich Maximale Schleuderdrehzahl Schleuderdrehzahlbereich Maximale Beladung Baumwolle 40 °C 95 °C – kalt 1400 U/min 1400 U/min – 400 U/min 8 kg Pflegeleicht 40 °C 60 °C – kalt 1200 U/min 1200 U/min – 400 U/min 3 kg Feinwäsche 40 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 3 kg Wolle/Seide 40 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 1.
www.aeg.com Mögliche Programmkombinationen Pflegeleicht Feinwäsche Wolle/Seide ÖKOPower Anti-Allergie 20 min. - 3 kg Outdoor Daunen ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Nur Abpumpen ■ ■ ■ ■ ■ ■ ■ Nur Schleudern ■ ■ ■ ■ ■ ■ ■ Flecken 1) ■ ■ ■ ■ Vorwäsche ■ ■ ■ ■ Extra Spülen ■ ■ ■ Nur Spülen ■ ■ ■ ■ ■ ■ Zeit Sparen 3) ■ ■ ■ Zeitvorwahl ■ ■ ■ Plus Dampf1) ■ ■ Soft Plus ■ ■ Optionen U./Min.
DEUTSCH 7.2 Woolmark Apparel Care Grün Das Waschprogramm Wolle dieser Maschine wurde von der Firma 21 Woolmark auf das Waschen von Wolltextilien mit der Pflegekennzeichnung „Handwäsche“ getestet und zugelassen, vorausgesetzt, dass die Wäsche gemäß der Anleitung auf dem Kleidungsetikett und gemäß den Angaben des Maschinenherstellers gewaschen wird. Beachten Sie die Trocken- und Waschanleitung auf dem Kleidungsetikett.
www.aeg.com Mit dieser Option verlängert sich die Programmdauer leicht. Min. gleichzeitig, bis das Symbol der Anzeige über leuchtet/erlischt. Berühren Sie zum Ein-/Ausschalten dieser Option die Tasten Temp. und U/ 9. VOR DER ERSTEN INBETRIEBNAHME 1. Stellen Sie sicher, dass alle Transportsicherungen aus dem Gerät entfernt wurden. 2. Achten Sie darauf, dass Spannung vorhanden und der Wasserhahn aufgedreht ist. 3. Gießen Sie 2 Liter Wasser in das Waschmittelfach mit der Markierung .
DEUTSCH 10.3 Einfüllen von Wasch- und Pflegemitteln 23 1 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. Fach für Vorwasch-, Einweichwaschmittel oder Fleckentferner. Fach für die Hauptwäsche. Fach für flüssige Pflegemittel (Weichspüler, Stärke). Maximaler Füllstand für flüssige Pflegemittel. Klappe für Waschpulver oder Flüssigwaschmittel. Halten Sie sich immer an die Anweisungen auf der Verpackung der Waschmittel.
www.aeg.com Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. • Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. • Stellen Sie nicht den Vorwaschgang ein. • Stellen Sie nicht die Zeitvorwahl ein. 5. Messen Sie Waschmittel und Weichspüler ab. 6. Schließen Sie die Waschmittelschublade vorsichtig. 3. Schalten Sie bei Bedarf eine oder mehrere Optionen durch Berühren der entsprechenden Tasten ein.
DEUTSCH 2. Berühren Sie die Taste Zeitvorwahl wiederholt, bis im Display erscheint. 3. Berühren Sie die Taste Start/Pause erneut, um das Programm sofort zu starten. Ändern der Zeitvorwahl nach dem Start des Countdowns Ändern der Zeitvorwahl: 1. Berühren Sie die Taste Start/Pause, um das Gerät in den Pausenmodus zu schalten. Die zugehörige Anzeige blinkt. 2. Berühren Sie die Taste Zeitvorwahl wiederholt, bis das Display die gewünschte Zeitvorwahl anzeigt. 3.
www.aeg.com Programmphase im Display (die Pfeile blinken abwechselnd). Wenn Sie Plus Dampf wählen, leuchten die Dampfphasenanzeigen. Die Dampfphase wird ausgeführt: . Die Knitterschutzphase wird ausgeführt: . 10.10 Unterbrechen eines Programms und Ändern der Optionen Wenn das Programm bereits gestartet wurde, können Sie nur einige der Optionen ändern: 1. Berühren Sie die Taste Start/Pause. Die zugehörige Kontrolllampe blinkt. 2. Ändern Sie die Optionen.
DEUTSCH 4. Lassen Sie die Tür und die Waschmittelschublade einen Spaltbreit geöffnet, damit sich kein Schimmel und keine unangenehmen Gerüche bilden. 5. Schließen Sie den Wasserhahn. 10.14 Abpumpen des Wassers nach dem Programmende Wenn Sie ein Programm oder eine Option gewählt haben, nach dem/der die Textilien im Wasser liegen bleiben, ist das Programm beendet, aber: • Im Display erscheint die Anzeige , die Optionsanzeige oder und das Türverriegelungssymbol . Die Anzeige der Programmphase blinkt.
www.aeg.com • • • • • • • und Druckknöpfe. Schließen Sie Gürtel. Leeren Sie die Taschen und stülpen Sie sie nach außen. Wenden Sie mehrlagige Textilien, Wolle und bedruckte Wäschestücke vor dem Waschen. Führen Sie eine Vorbehandlung hartnäckiger Flecken durch. Waschen Sie stark verschmutzte Bereiche mit einem speziellen Waschmittel. Seien Sie vorsichtig mit Gardinen. Entfernen Sie die Haken, oder stecken Sie die Gardinen in ein Wäschenetz oder einen Kopfkissenbezug.
DEUTSCH Wenden Sie sich an Ihr örtliches Wasserversorgungsunternehmen, um die Wasserhärte in Ihrem Gebiet zu erfahren. 29 Anweisungen auf der Verpackung des Produkts. Verwenden Sie die richtige Menge Wasserenthärter. Halten Sie sich an die 12. REINIGUNG UND PFLEGE WARNUNG! Siehe Kapitel Sicherheitshinweise. 12.1 Reinigen der Außenseiten Reinigen Sie das Gerät nur mit warmem Wasser und etwas milder Seife. Reiben Sie alle Oberflächen sorgfältig trocken.
www.aeg.com Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts. 2. Starten Sie ein kurzes Programm für Baumwolle mit hoher Temperatur, leerer Trommel und etwas Waschpulver, um Rückstände auszuspülen. 12.6 Reinigen der Waschmittelschublade Um Ablagerungen von getrocknetem Waschmittel oder verklumptem Weichspüler und/oder die Schimmelbildung in der Waschmittelschublade zu vermeiden, führen Sie das folgende Reinigungsverfahren von Zeit zu Zeit durch. 3.
DEUTSCH 31 12.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. 1 1 Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. Reinigen Sie die Ablaufpumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht. • Das Gerät macht ein ungewöhnliches Geräusch, weil die Ablaufpumpe blockiert ist. 2 4. Lassen Sie das Wasser ablaufen. • Im Display wird der Alarmcode angezeigt.
www.aeg.com 2 2 1 1 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, dass sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst. 12. Schließen Sie die Pumpenabdeckung. 2 1 10. Reinigen Sie das Sieb unter fließendem Wasser. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: a.
DEUTSCH 33 1 2 45° 3 20° 2. Lockern Sie die Ringmutter, um den Zulaufschlauch vom Gerät zu entfernen. 12.9 Notentleerung Kann das Gerät das Wasser nicht abpumpen, führen Sie den unter „Reinigen des Ablauffilters“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 1.
www.aeg.com WARNUNG! Stellen Sie sicher, dass die Temperatur über 0 °C liegt, bevor Sie das Gerät wieder einschalten. Der Hersteller ist nicht für Schäden verantwortlich, die auf zu niedrige Temperaturen zurückzuführen sind. 13. FEHLERSUCHE WARNUNG! Siehe Kapitel Sicherheitshinweise. 13.1 Einführung Das Gerät startet nicht oder bleibt während des Betriebs stehen. Versuchen Sie zunächst, selbst eine Lösung für das Problem zu finden (siehe Tabelle).
DEUTSCH 35 13.2 Mögliche Störungen Störung Das Programm startet nicht. Mögliche Abhilfe • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. • Stellen Sie sicher, dass Start/Pause berührt wurde. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab oder warten Sie, bis sie abgelaufen ist.
www.aeg.com Störung Mögliche Abhilfe Es befindet sich Wasser auf dem Boden. • Vergewissern Sie sich, dass alle Wasseranschlüsse vollkommen dicht sind, sodass kein Wasser austreten kann. • Vergewissern Sie sich, dass der Wasserzulauf- und -ablaufschlauch nicht beschädigt sind. • Verwenden Sie ein geeignetes Waschmittel in der richtigen Menge. Die Tür des Geräts lässt sich nicht öffnen. • Prüfen Sie, ob das gewählte Waschprogramm mit Wasser in der Trommel endet.
DEUTSCH 37 Schalten Sie das Gerät nach der Überprüfung wieder ein. Das Programm wird an der Stelle fortgesetzt, an der es unterbrochen wurde. Tritt das Problem erneut auf, wenden Sie sich an den autorisierten Kundendienst. Wenn im Display andere Alarmcodes angezeigt werden. Schalten Sie das Gerät aus und wieder ein. Tritt das Problem weiterhin auf, wenden Sie sich an den autorisierten Kundendienst. 13.
www.aeg.com Während des Waschprogramms können durch die ProSense-Technologie die Programmdauer und die Verbrauchswerte variieren. Siehe „ProSense-Beladungserkennung“ im Kapitel „Täglicher Gebrauch“. Programme Beladung (kg) EnergieWasserUngefähverbrauch verbrauch re Pro(kWh) (Liter) grammdauer (in Minuten) Restfeuchte (%)1) Baumwolle60°C 8 1.40 90 230 52 Baumwolle40°C 8 1.30 90 220 52 Pflegeleicht40°C 3 0.90 60 140 35 Feinwäsche40°C 3 0.60 60 120 35 Wolle/Seide30°C 1.5 0.
DEUTSCH Die Schutzverkleidung gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt.
www.aeg.com mitgelieferten Broschüre aufgeführten Geräten verwendet werden. So steht Ihr Gerät höher und die Be- und Entladung wird einfacher. Lesen Sie die dem Gerät und dem Zubehör beiliegenden Anleitungen sorgfältig durch. Die Schublade kann zur Aufbewahrung von Wäsche benutzt werden, z. B. für Handtücher, Reinigungsprodukte usw. Lesen Sie die mit dem Zubehör gelieferte Gebrauchsanleitung sorgfältig durch. WARNUNG! Stellen Sie den Wäschetrockner nicht unter die Waschmaschine. 16.
DEUTSCH 41
www.aeg.
DEUTSCH 43
157003811-A-012017 www.aeg.