L8FE86498 USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................4 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 11 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com 1.2 Allgemeine Sicherheit • • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Überschreiten Sie nicht die maximale Beladungsmenge von 9 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • • • • • • • • • verriegeln und dadurch interne Schäden zu vermeiden. Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk. Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. Halten Sie sich an die mitgelieferte Montageanleitung. Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist.
www.aeg.com Substanzen verschmutzt sind. Die Gummiteile der Waschmaschine könnten beschädigt werden. Waschen Sie solche Textilien mit der Hand vor, bevor Sie sie in die Waschmaschine geben. • Berühren Sie während des Ablaufs eines Programms nicht die Glastür. Das Glas kann sehr heiß werden. 2.5 Service • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung.
DEUTSCH 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 1 2 8. Reinigen Sie die Unterseite des Geräts und trocknen Sie sie ab. 7 VORSICHT! Verwenden Sie keinen Alkohol, keine Lösungsmittel und keine Chemikalien. 9. Sortieren Sie die verschiedenen Teile des Schallschutzes nach Größe und Position.
www.aeg.com x4 A B Bringen Sie die Schallschutzteile bei Raumtemperatur an. 13. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 14. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. 16. Ziehen Sie die KunststoffAbstandshalter heraus. 17. Setzen Sie die Kunststoffkappen, die sich im Beutel mit der Bedienungsanleitung befinden, in die Löcher ein. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren. 3.
DEUTSCH 9 WARNUNG! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 45 20 x4 Das Gerät muss einen waagerechten und festen Stand haben. Durch eine korrekte waagrechte Ausrichtung des Geräts werden Vibrationen, Geräusche und ein Wandern des Geräts während des Betriebs vermieden. O O Vergewissern Sie sich, dass sich der Zulaufschlauch nicht in der vertikalen Position befindet. 3. Lösen Sie ggf.
www.aeg.com durch natürliche Alterung auftreten können. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an. A Tritt dieser Fall ein, drehen Sie den Wasserhahn zu und wenden Sie sich an den autorisierten Kundendienst, um den Schlauch zu erneuern. 3.5 Ablassen des Wassers Der Ablaufschlauch muss in einer Höhe nicht unter 60 cm und nicht über 100 cm angebracht werden.
DEUTSCH 11 Stellen Sie sicher, dass der Ablaufschlauch einen Bogen beschreibt, damit keine Partikel aus dem Becken in das Gerät gelangen können. 6. Stecken Sie den Schlauch direkt in ein Abflussrohr in der Zimmerwand und befestigen Sie ihn mit einer Schlauchschelle. 5. Ohne Kunststoffschlauchführung: Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Orientieren Sie sich an der Abbildung. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
www.aeg.com 4.2 Geräteübersicht 1 2 9 8 3 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Arbeitsplatte Waschmittelschublade Bedienfeld Türgriff Typenschild Filter der Ablaufpumpe Füße für die Ausrichtung des Geräts 8 9 10 11 12 Ablaufschlauch Anschluss des Zulaufschlauchs Netzkabel Transportschrauben Schlauchhalter 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 Programme Baumwolle Pflegeleicht Feinwäsche Wolle/Seide Dampf ÖKOPower Anti-Allergie 20 min.
DEUTSCH 13 1 Programmwahlschalter 2 Display 3 Sensortaste Energie Sparen (Eco) 7 Sensortaste Extra Spülen (Extra Spülen) 8 Sensortaste Zeitvorwahl (Zeitvorwahl) 4 Sensortaste Zeit Sparen (Zeit Sparen) 9 Sensortaste Plus Dampf (Plus Dampf) 5 Sensortaste Überspringen (Option) 10 Sensortaste Flecken und Vorwäsche (Flecken/Vorw.) 11 Sensortaste Drehzahlreduzierung (U./ Min.
www.aeg.com Die Digitalanzeige zeigt Folgendes an: ). • Programmdauer (z. B. • Zeitvorwahl (z. B. oder ). • Programmende ( ). • Fehlercode (z. B. ). Energiesparanzeigen. Die Anzeige erscheint, wenn ein Baumwollprogramm mit 40 °C oder 60 °C gewählt wird. Hauptwaschgangsanzeige: Blinkt während der Vorwäsche und Hauptwaschphase. Spülphasenanzeige: Blinkt während der Spülphase. Die Anzeige erscheint, wenn die Option Soft Plus eingeschaltet ist. Schleuder- und Abpumpphasenanzeige.
DEUTSCH Da die Standby-Funktion das Gerät automatisch ausschaltet, um in einigen Fällen den Stromverbrauch zu verringern, müssen Sie es möglicherweise erneut einschalten. Siehe Abschnitt Standby im Kapitel „Täglicher Gebrauch“. 6.2 Einführung Die Optionen/Funktionen lassen sich nicht zusammen mit allen Waschprogrammen auswählen. Prüfen Sie die Kompatibilität der Optionen/Funktionen mit den Waschprogrammen in der „Programmübersicht“. Eine Option/Funktion kann eine andere ausschließen.
www.aeg.com • Flecken Wählen Sie diese Option zur Vorbehandlung stark verschmutzter oder stark fleckiger Wäsche mit einem Fleckentferner. Geben Sie den Fleckentferner in das Fach . Der Fleckentferner wird vorgemischt und mit dem Waschmittel erwärmt, um die Wirksamkeit zu verbessern. Mit dieser Option kann sich die Programmdauer verlängern. Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C.
DEUTSCH Wenn Sie ein Baumwollprogramm mit 40 °C oder 60 °C wählen, erscheint im Display die . Das sind Anzeige die standardmäßigen Baumwollprogramme, die hinsichtlich des Energie- und Wasserverbrauchs am effizientesten sind. Alle eingestellten Optionen (mit Ausnahme von Extra Spülen) werden automatisch abgewählt. • Nur Schleudern bei zweimaliger Berührung. Das Gerät lässt die Wasch- und Spülphase aus. • Nur Abpumpen bei dreimaliger Berührung. Das Gerät pumpt nur das Wasser ab.
www.aeg.com Programm Programmbeschreibung Baumwolle Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte. Das Programm Baumwolle bei 60 °C und das Programm Baumwolle bei 40 °C mit der Option sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“.
DEUTSCH Programm Anti-Allergie 20 min. - 3 kg Outdoor 19 Programmbeschreibung Weiße Baumwollwäsche. Dieses Programm beseitigt Mikroorganismen durch einen Waschgang, bei dem die Temperatur für einige Minuten auf über 60 °C gehalten wird. So werden Keime, Bakterien, Mikroorganismen und Partikel entfernt. Ein zusätzlicher Spülgang sorgt dafür, dass Waschmittelrückstände und Pollen/Allergene beseitigt werden. Auf diese Weise wird die Reinigung effektiver.
www.aeg.com Programmtemperatur, maximale Schleuderdrehzahl und maximale Beladung Programm Standardtemperatur Maximale Schleuder- Maximale BelaTemperaturbereich drehzahl dung Schleuderdrehzahlbereich Baumwolle 40 °C 95 °C – kalt 1400 U/min 1400 U/min – 400 U/min 9 kg Pflegeleicht 40 °C 60 °C – kalt 1200 U/min 1200 U/min – 400 U/min 4 kg Feinwäsche 40 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 4 kg Wolle/Seide 40 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 2 kg - - 1.
DEUTSCH 21 Feinwäsche ÖKOPower Anti-Allergie 20 min. - 3 kg Outdoor Daunen ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Flecken1) ■ ■ ■ ■ Vorwäsche ■ ■ ■ ■ Extra Spülen ■ ■ ■ Eco 2) ■ ■ ■ Zeit Sparen 3) ■ ■ ■ Nur Spülen ■ ■ ■ ■ ■ ■ ■ ■ ■ Nur Schleudern ■ ■ ■ ■ ■ ■ ■ ■ ■ Nur Abpumpen ■ ■ ■ ■ ■ ■ ■ ■ ■ Zeitvorwahl ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Plus Dampf 1) Soft Plus Dampf Pflegeleicht ■ U./Min.
www.aeg.com 7.2 Woolmark Apparel Care Grün Das Waschprogramm Wolle dieser Maschine wurde von der Firma Woolmark auf das Waschen von Wolltextilien mit der Pflegekennzeichnung „Handwäsche“ getestet und zugelassen, vorausgesetzt, dass die Wäsche gemäß der Anleitung auf dem Kleidungsetikett und gemäß den Angaben des Maschinenherstellers gewaschen wird. Beachten Sie die Trocken- und Waschanleitung auf dem Kleidungsetikett.
DEUTSCH Sind die akustischen Signale ausgeschaltet, ertönen sie nur noch dann, wenn eine Störung vorliegt. 9.3 Extra Spülen dauerhaft einschalten Wenn Sie diese Option wählen, ist bei Auswahl eines kompatiblen Programms die Funktion Extra Spülen stets eingeschaltet. • Berühren Sie zum Ein-/Ausschalten dieser Option die Tasten Extra Spülen und Option gleichzeitig, bis die zugehörige Anzeige aufleuchtet/ erlischt. Diese Option fügt dem Programm zwei Spülgänge hinzu und das Display zeigt 9.
www.aeg.com 10.3 Einfüllen von Wasch- und Pflegemitteln 1 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. A Fach für Vorwäsche und Einweichprogramm. Fach für die Hauptwäsche. Fach für flüssige Pflegemittel (Weichspüler, Stärke). Maximaler Füllstand für flüssige Pflegemittel. Fach für den Fleckentferner. Klappe für Waschpulver oder Flüssigwaschmittel. Halten Sie sich immer an die Anweisungen auf der Verpackung der Waschmittel.
DEUTSCH Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. • Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. • Stellen Sie nicht den Vorwaschgang ein. • Stellen Sie nicht die Zeitvorwahl ein. 5. Messen Sie Waschmittel und Weichspüler ab. 6. Schließen Sie die Waschmittelschublade vorsichtig. 25 3. Schalten Sie bei Bedarf eine oder mehrere Optionen durch Berühren der entsprechenden Tasten ein.
www.aeg.com 2. Berühren Sie die Taste Zeitvorwahl wiederholt, bis im Display erscheint. 3. Berühren Sie die Taste Start/Pause erneut, um das Programm sofort zu starten. Ändern der Zeitvorwahl nach dem Start des Countdowns Ändern der Zeitvorwahl: 1. Berühren Sie die Taste Start/Pause, um das Gerät in den Pausenmodus zu schalten. Die zugehörige Anzeige blinkt. 2. Berühren Sie die Taste Zeitvorwahl wiederholt, bis das Display die gewünschte Zeitvorwahl anzeigt. 3.
DEUTSCH Programmphase im Display (die Pfeile blinken abwechselnd). Wenn Sie Plus Dampf wählen, leuchten die Dampfphasenanzeigen. Die Dampfphase wird ausgeführt: . Die Knitterschutzphase wird ausgeführt: . 10.10 Unterbrechen eines Programms und Ändern der Optionen Wenn das Programm bereits gestartet wurde, können Sie nur einige der Optionen ändern: 1. Berühren Sie die Taste Start/Pause. Die zugehörige Kontrolllampe blinkt. 2. Ändern Sie die Optionen.
www.aeg.com 4. Lassen Sie die Tür und die Waschmittelschublade einen Spaltbreit geöffnet, damit sich kein Schimmel und keine unangenehmen Gerüche bilden. 5. Schließen Sie den Wasserhahn. 10.14 Abpumpen des Wassers nach dem Programmende Wenn Sie ein Programm oder eine Option gewählt haben, nach dem/der die Textilien im Wasser liegen bleiben, ist das Programm beendet, aber: • Im Display erscheint die Anzeige , die Optionsanzeige oder und das Türverriegelungssymbol .
DEUTSCH • • • • • • • und Druckknöpfe. Schließen Sie Gürtel. Leeren Sie die Taschen und stülpen Sie sie nach außen. Wenden Sie mehrlagige Textilien, Wolle und bedruckte Wäschestücke vor dem Waschen. Führen Sie eine Vorbehandlung hartnäckiger Flecken durch. Waschen Sie stark verschmutzte Bereiche mit einem speziellen Waschmittel. Seien Sie vorsichtig mit Gardinen. Entfernen Sie die Haken, oder stecken Sie die Gardinen in ein Wäschenetz oder einen Kopfkissenbezug.
www.aeg.com Wenden Sie sich an Ihr örtliches Wasserversorgungsunternehmen, um die Wasserhärte in Ihrem Gebiet zu erfahren. Anweisungen auf der Verpackung des Produkts. Verwenden Sie die richtige Menge Wasserenthärter. Halten Sie sich an die 12. REINIGUNG UND PFLEGE WARNUNG! Siehe Kapitel Sicherheitshinweise. 12.1 Reinigen der Außenseiten Reinigen Sie das Gerät nur mit warmem Wasser und etwas milder Seife. Reiben Sie alle Oberflächen sorgfältig trocken.
DEUTSCH 31 Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts. 2. Starten Sie ein kurzes Programm für Baumwolle mit hoher Temperatur, leerer Trommel und etwas Waschpulver, um Rückstände auszuspülen. 12.6 Reinigen der Waschmittelschublade Um Ablagerungen von getrocknetem Waschmittel oder verklumptem Weichspüler und/oder die Schimmelbildung in der Waschmittelschublade zu vermeiden, führen Sie das folgende Reinigungsverfahren von Zeit zu Zeit durch. 3.
www.aeg.com 12.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. 1 1 Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. Reinigen Sie die Ablaufpumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht. • Das Gerät macht ein ungewöhnliches Geräusch, weil die Ablaufpumpe blockiert ist. 2 4. Lassen Sie das Wasser ablaufen. • Im Display wird der Alarmcode angezeigt.
DEUTSCH 33 2 2 1 1 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, dass sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst. 12. Schließen Sie die Pumpenabdeckung. 2 1 10. Reinigen Sie das Sieb unter fließendem Wasser. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: a.
www.aeg.com 1 2 45° 3 20° 2. Lockern Sie die Ringmutter, um den Zulaufschlauch vom Gerät zu entfernen. 12.9 Notentleerung Kann das Gerät das Wasser nicht abpumpen, führen Sie den unter „Reinigen des Ablauffilters“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 1.
DEUTSCH 35 WARNUNG! Stellen Sie sicher, dass die Temperatur über 0 °C liegt, bevor Sie das Gerät wieder einschalten. Der Hersteller ist nicht für Schäden verantwortlich, die auf zu niedrige Temperaturen zurückzuführen sind. 13. FEHLERSUCHE WARNUNG! Siehe Kapitel Sicherheitshinweise. 13.1 Einführung Das Gerät startet nicht oder bleibt während des Betriebs stehen. Versuchen Sie zunächst, selbst eine Lösung für das Problem zu finden (siehe Tabelle).
www.aeg.com 13.2 Mögliche Störungen Störung Das Programm startet nicht. Mögliche Abhilfe • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. • Stellen Sie sicher, dass Start/Pause berührt wurde. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab oder warten Sie, bis sie abgelaufen ist.
DEUTSCH 37 Störung Mögliche Abhilfe Es befindet sich Wasser auf dem Boden. • Vergewissern Sie sich, dass alle Wasseranschlüsse vollkommen dicht sind, sodass kein Wasser austreten kann. • Vergewissern Sie sich, dass der Wasserzulauf- und -ablaufschlauch nicht beschädigt sind. • Verwenden Sie ein geeignetes Waschmittel in der richtigen Menge. Die Tür des Geräts lässt sich nicht öffnen. • Prüfen Sie, ob das gewählte Waschprogramm mit Wasser in der Trommel endet.
www.aeg.com Schalten Sie das Gerät nach der Überprüfung wieder ein. Das Programm wird an der Stelle fortgesetzt, an der es unterbrochen wurde. Tritt das Problem erneut auf, wenden Sie sich an den autorisierten Kundendienst. Wenn im Display andere Alarmcodes angezeigt werden. Schalten Sie das Gerät aus und wieder ein. Tritt das Problem weiterhin auf, wenden Sie sich an den autorisierten Kundendienst. 13.
DEUTSCH Während des Waschprogramms können durch die ProSense-Technologie die Programmdauer und die Verbrauchswerte variieren. Siehe „ProSense-Beladungserkennung“ im Kapitel „Täglicher Gebrauch“. Programme Beladung (kg) EnergieWasserUngefähverbrauch verbrauch re Pro(kWh) (Liter) grammdauer (in Minuten) Restfeuchte (%)1) Baumwolle60°C 9 1.55 87 220 52 Baumwolle40°C 9 0.97 87 205 52 Pflegeleicht40°C 4 0.72 55 155 35 Feinwäsche40°C 4 0.60 59 89 35 Wolle/Seide30°C 2 0.
www.aeg.com Die Schutzverkleidung gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt.
DEUTSCH 41 mitgelieferten Broschüre aufgeführten Geräten verwendet werden. So steht Ihr Gerät höher und die Be- und Entladung wird einfacher. Lesen Sie die dem Gerät und dem Zubehör beiliegenden Anleitungen sorgfältig durch. Die Schublade kann zur Aufbewahrung von Wäsche benutzt werden, z. B. für Handtücher, Reinigungsprodukte usw. Lesen Sie die mit dem Zubehör gelieferte Gebrauchsanleitung sorgfältig durch. WARNUNG! Stellen Sie den Wäschetrockner nicht unter die Waschmaschine. 16.
www.aeg.
DEUTSCH 43
132935901-A-052017 www.aeg.