L8FE86693 USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................4 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 11 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com 1.2 Allgemeine Sicherheit • • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Überschreiten Sie nicht die maximale Beladungsmenge von 9 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • • • • • • • • • verriegeln und dadurch interne Schäden zu vermeiden. Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk. Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. Halten Sie sich an die mitgelieferte Montageanleitung. Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist.
www.aeg.com Substanzen verschmutzt sind. Die Gummiteile der Waschmaschine könnten beschädigt werden. Waschen Sie solche Textilien mit der Hand vor, bevor Sie sie in die Waschmaschine geben. • Berühren Sie während des Ablaufs eines Programms nicht die Glastür. Das Glas kann sehr heiß werden. 2.5 Service • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung.
DEUTSCH 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 1 2 8. Reinigen Sie die Unterseite des Geräts und trocknen Sie sie ab. 7 VORSICHT! Verwenden Sie keinen Alkohol, keine Lösungsmittel und keine Chemikalien. 9. Sortieren Sie die verschiedenen Teile des Schallschutzes nach Größe und Position.
www.aeg.com x4 A B Bringen Sie die Schallschutzteile bei Raumtemperatur an. 13. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 14. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. 16. Ziehen Sie die KunststoffAbstandshalter heraus. 17. Setzen Sie die Kunststoffkappen, die sich im Beutel mit der Bedienungsanleitung befinden, in die Löcher ein. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren. 3.
DEUTSCH 9 WARNUNG! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 45 20 x4 Das Gerät muss einen waagerechten und festen Stand haben. Durch eine korrekte waagrechte Ausrichtung des Geräts werden Vibrationen, Geräusche und ein Wandern des Geräts während des Betriebs vermieden. O O Vergewissern Sie sich, dass sich der Zulaufschlauch nicht in der vertikalen Position befindet. 3. Lösen Sie ggf.
www.aeg.com durch natürliche Alterung auftreten können. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an. A Tritt dieser Fall ein, drehen Sie den Wasserhahn zu und wenden Sie sich an den autorisierten Kundendienst, um den Schlauch zu erneuern. 3.5 Ablassen des Wassers Der Ablaufschlauch muss in einer Höhe nicht unter 60 cm und nicht über 100 cm angebracht werden.
DEUTSCH 11 Stellen Sie sicher, dass der Ablaufschlauch einen Bogen beschreibt, damit keine Partikel aus dem Becken in das Gerät gelangen können. 6. Stecken Sie den Schlauch direkt in ein Abflussrohr in der Zimmerwand und befestigen Sie ihn mit einer Schlauchschelle. 5. Ohne Kunststoffschlauchführung: Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Orientieren Sie sich an der Abbildung. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
www.aeg.com 4.2 Geräteübersicht 1 2 9 8 3 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Arbeitsplatte Waschmittelschublade Bedienfeld Türgriff Typenschild Filter der Ablaufpumpe Füße für die Ausrichtung des Geräts 8 9 10 11 12 Ablaufschlauch Anschluss des Zulaufschlauchs Netzkabel Transportschrauben Schlauchhalter 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 Programme Baumwolle Pflegeleicht Feinwäsche Wolle/Seide Dampf ÖKOPower Anti-Allergie 20 min.
DEUTSCH 13 1 Programmwahlschalter 2 Display 3 Sensortaste Energie Sparen (Eco) 7 Sensortaste Extra Spülen (Extra Spülen) 8 Sensortaste Zeitvorwahl (Zeitvorwahl) 4 Sensortaste Zeit Sparen (Zeit Sparen) 9 Sensortaste Plus Dampf (Plus Dampf) 5 Sensortaste Überspringen (Option) 10 Sensortaste Flecken und Vorwäsche (Flecken/Vorw.) 11 Sensortaste Drehzahlreduzierung (U./ Min.
www.aeg.com Die Digitalanzeige zeigt Folgendes an: ). • Programmdauer (z. B. • Zeitvorwahl (z. B. oder ). • Programmende ( ). • Fehlercode (z. B. ). Energiesparanzeigen. Die Anzeige erscheint, wenn ein Baumwollprogramm mit 40 °C oder 60 °C gewählt wird. Hauptwaschgangsanzeige: Blinkt während der Vorwäsche und Hauptwaschphase. Spülphasenanzeige: Blinkt während der Spülphase. Die Anzeige erscheint, wenn die Option Soft Plus eingeschaltet ist. Schleuder- und Abpumpphasenanzeige.
DEUTSCH Da die Standby-Funktion das Gerät automatisch ausschaltet, um in einigen Fällen den Stromverbrauch zu verringern, müssen Sie es möglicherweise erneut einschalten. Siehe Abschnitt Standby im Kapitel „Täglicher Gebrauch“. 6.2 Einführung Die Optionen/Funktionen lassen sich nicht zusammen mit allen Waschprogrammen auswählen. Prüfen Sie die Kompatibilität der Optionen/Funktionen mit den Waschprogrammen in der „Programmübersicht“. Eine Option/Funktion kann eine andere ausschließen.
www.aeg.com • Flecken Wählen Sie diese Option zur Vorbehandlung stark verschmutzter oder stark fleckiger Wäsche mit einem Fleckentferner. Geben Sie den Fleckentferner in das Fach . Der Fleckentferner wird vorgemischt und mit dem Waschmittel erwärmt, um die Wirksamkeit zu verbessern. Mit dieser Option kann sich die Programmdauer verlängern. Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C.
DEUTSCH Wenn Sie ein Baumwollprogramm mit 40 °C oder 60 °C wählen, erscheint im Display die . Das sind Anzeige die standardmäßigen Baumwollprogramme, die hinsichtlich des Energie- und Wasserverbrauchs am effizientesten sind. Alle eingestellten Optionen (mit Ausnahme von Extra Spülen) werden automatisch abgewählt. • Nur Schleudern bei zweimaliger Berührung. Das Gerät lässt die Wasch- und Spülphase aus. • Nur Abpumpen bei dreimaliger Berührung. Das Gerät pumpt nur das Wasser ab.
www.aeg.com Programm Programmbeschreibung Baumwolle Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte. Das Programm Baumwolle bei 60 °C und das Programm Baumwolle bei 40 °C mit der Option sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“.
DEUTSCH Programm Anti-Allergie 20 min. - 3 kg Outdoor 19 Programmbeschreibung Weiße Baumwollwäsche. Dieses Programm beseitigt Mikroorganismen durch einen Waschgang, bei dem die Temperatur für einige Minuten auf über 60 °C gehalten wird. So werden Keime, Bakterien, Mikroorganismen und Partikel entfernt. Ein zusätzlicher Spülgang sorgt dafür, dass Waschmittelrückstände und Pollen/Allergene beseitigt werden. Auf diese Weise wird die Reinigung effektiver.
www.aeg.com Programm Programmbeschreibung Wartungszyklus mit Heißwasser zur Reinigung und Auffrischung der Trommel und zum Entfernen von Rückständen, die Gerüche absondern können. Schalten Sie dieses Programm einmal im Monat ein, um beste Ergebnisse zu erzielen. Nehmen Sie alle Gegenstände aus der Trommel, bevor Sie das Programm einschalten. Drehen Sie in der Waschmittelschublade die Klappe im Fach für den Hauptwaschgang nach oben.
DEUTSCH Programm Standardtemperatur Maximale Schleuder- Maximale BelaTemperaturbereich drehzahl dung Schleuderdrehzahlbereich ÖKOPower 30 °C 60 °C - 30 °C 1600 U/min 1600 U/min - 400 U/min 5 kg Anti-Allergie 60 °C 1600 U/min 1600 U/min - 400 U/min 9 kg 20 min. - 3 kg 30 °C 40 °C - 30 °C 1200 U/min 1200 U/min - 400 U/min 3 kg Outdoor 30 °C 40 °C – kalt 1200 U/min 1200 U/min - 400 U/min Maschinenreinigung 60 °C 1200 U/min 1200 U/min - 400 U/min 2.5 kg1) 1 kg2) - 1) Waschprogramm.
Anti-Allergie 20 min. - 3 kg Outdoor ■ ■ Nur Spülen ■ ■ ■ ■ ■ ■ ■ ■ Nur Schleudern ■ ■ ■ ■ ■ ■ ■ ■ Nur Abpumpen ■ ■ ■ ■ ■ ■ ■ ■ Zeitvorwahl ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Plus Dampf 1) Soft Plus Maschinenreinigung ÖKOPower ■ Dampf Feinwäsche Zeit Sparen 3) Wolle/Seide Pflegeleicht www.aeg.com Baumwolle 22 ■ ■ ■ ■ ■ ■ 1) Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C.
DEUTSCH 3. Gießen Sie 2 Liter Wasser in das Waschmittelfach mit der Markierung . Hierdurch wird das Abpumpsystem aktiviert. 4. Geben Sie eine kleine Menge Waschmittel in das Fach mit der Markierung 23 5. Stellen Sie ein Baumwollprogramm mit der höchsten Temperatur ein und starten Sie das Programm ohne Wäsche. So werden alle eventuellen Verunreinigungen aus Trommel und Bottich entfernt. . 9. EINSTELLUNGEN 9.1 Kindersicherung Diese Option verhindert, dass Kinder mit dem Bedienfeld spielen.
www.aeg.com 10. TÄGLICHER GEBRAUCH WARNUNG! Siehe Kapitel Sicherheitshinweise. 10.1 Einschalten des Geräts 1. Stecken Sie den Netzstecker in die Netzsteckdose. 2. Öffnen Sie den Wasserhahn. 3. Halten Sie die Taste Ein/Aus einige Sekunden lang gedrückt, um das Gerät einzuschalten. Es ertönt eine kurze Melodie (falls eingeschaltet). Der Programmwahlschalter wird automatisch auf Baumwolle gesetzt. VORSICHT! Vergewissern Sie sich, dass keine Wäschestücke zwischen Dichtung und Tür eingeklemmt sind.
DEUTSCH 25 Entfernen Sie nach dem Waschgang bei Bedarf Waschmittelreste aus der Waschmittelschublade. 10.4 Überprüfen Sie die Position der Klappe 1. Ziehen Sie die Waschmittelschublade bis zum Anschlag heraus. 2. Drücken Sie den Hebel nach unten und ziehen Sie die Schublade heraus. 1 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz.
www.aeg.com gewünschte Waschprogramm. Die entsprechende Programmanzeige leuchtet auf. Die Kontrolllampe der Taste Start/Pause blinkt. Das Display zeigt die maximal zulässige Füllmenge für das Programm, die Standardtemperatur, die maximale Schleuderdrehzahl, die Programmphasen (falls verfügbar) und die voraussichtliche Programmdauer an. 2. Berühren Sie die entsprechenden Tasten, um die Temperatur und/oder Schleuderdrehzahl zu ändern. 3.
DEUTSCH 2. Am Ende der Beladungskennung und der Zeiterlischt die Anzeige Doppelpunkt hört auf zu blinken. Die Programmdauer wird entsprechend angepasst und kann sich verlängern oder verkürzen. Nach weiteren 30 Sekunden beginnt das Wasser einzulaufen. Falls am Ende der Beladungserkennung die Trommel überladen ist, blinkt die Anzeige im Display: In diesem Fall können Sie innerhalb von 30 Sekunden das Gerät anhalten und die überzähligen Wäschestücke entnehmen.
www.aeg.com Wurde die ProSense-Phase bereits beendet und läuft Wasser in das Gerät ein, startet das neue Programm ohne die ProSense-Phase zu wiederholen. Um Wasser und Waschmittel nicht zu verschwenden, wird das Wasser nicht abgepumpt. Das Display zeigt die maximale Programmdauer an, die etwa 20 Minuten nach dem Start des neuen Programms aktualisiert wird. 10.
DEUTSCH Die Optionsanzeige oder erlischt, während die Anzeige blinkt und dann erlischt. 3. Wenn das Programm beendet ist und die Türverriegelungsanzeige erlischt, können Sie die Tür öffnen. 4. Halten Sie die Taste Ein/Aus einige Sekunden lang gedrückt, um das Gerät auszuschalten. In jedem Fall pumpt das Gerät das Wasser nach etwa 18 Stunden automatisch ab. 10.
www.aeg.com 11.2 Hartnäckige Flecken Für manche Flecken sind Wasser und Waschmittel nicht ausreichend. Wir empfehlen, diese Flecken vorzubehandeln, bevor Sie die entsprechenden Textilien in das Gerät geben. Spezial-Fleckentferner sind im Handel erhältlich. Verwenden Sie einen SpezialFleckentferner, der für den jeweiligen Flecken- und Gewebetyp geeignet ist. 11.
DEUTSCH 12.2 Entkalkung Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Entkalkers für Waschmaschinen. Prüfen Sie die Trommel regelmäßig auf Kalkablagerungen. Herkömmliche Waschmittel enthalten Wasserenthärtungsmittel, wir empfehlen dennoch gelegentlich ein Programm mit leerer Trommel und einem Entkalker durchzuführen. Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts. 12.
www.aeg.com zu beseitigen. Setzen Sie nach der Reinigung das Oberteil wieder ein. 12.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. 3. Stellen Sie sicher, dass alle Waschmittelreste an der Ober- und Unterseite der Aufnahme entfernt wurden. Reinigen Sie die Schubladenaufnahme mit einer kleinen Bürste.
DEUTSCH 33 2 1 1 2 4. Lassen Sie das Wasser ablaufen. 1 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, dass sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst. 5. Wenn der Behälter voll ist, schließen Sie den Ablaufkanal und leeren Sie den Behälter. 6. Wiederholen Sie die Schritte 4 und 5, bis kein Wasser mehr herausfließt. 2 10. Reinigen Sie das Sieb unter fließendem Wasser. 1 7.
www.aeg.com 1 2 1 2 3 2. Lockern Sie die Ringmutter, um den Zulaufschlauch vom Gerät zu entfernen. 12. Schließen Sie die Pumpenabdeckung. 2 1 Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: a. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. b. Starten Sie das Programm zum Abpumpen des Wassers. 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 12.
DEUTSCH 35 0 °C erreichen oder unter 0 °C sinken kann, entfernen Sie das im Zulaufschlauch und in der Ablaufpumpe verbliebene Wasser. 45° 20° 12.9 Notentleerung Kann das Gerät das Wasser nicht abpumpen, führen Sie den unter „Reinigen des Ablauffilters“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. 1. Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Schließen Sie den Wasserhahn. 3.
www.aeg.com Ist das Gerät überladen, nehmen Sie einige Wäschestücke aus der Trommel und/oder drücken Sie die Tür zu und berühren Sie gleichzeitig die Taste Start/Pause, bis die Anzeige aufhört zu blinken (siehe Abbildung unten). • - Die Stromzufuhr ist nicht konstant. Warten Sie, bis die Netzspannung wieder konstant ist. • - Keine Kommunikation zwischen den elektronischen Bauteilen des Geräts. Schalten Sie das Gerät aus und wieder ein. • – Das Aqua-Control-System ist eingeschaltet.
DEUTSCH Störung 37 Mögliche Abhilfe Das Wasser, das in das • Vergewissern Sie sich, dass sich der Ablaufschlauch in der Gerät einläuft, wird sofort richtigen Höhe befindet. Der Schlauch ist möglicherweise abgepumpt zu niedrig angebracht. Siehe hierzu „Montage“. Das Gerät pumpt das Wasser nicht ab. • Stellen Sie sicher, dass der Siphon nicht verstopft ist. • Vergewissern Sie sich, dass der Ablaufschlauch nicht geknickt oder zu stark gekrümmt ist.
www.aeg.com Störung Mögliche Abhilfe Das Gerät verursacht ein ungewöhnliches Geräusch und vibriert. • Stellen Sie sicher, dass das Gerät richtig ausgerichtet ist. Siehe hierzu „Montage“. • Überzeugen Sie sich, dass das Verpackungsmaterial und/ oder die Transportsicherungen entfernt wurden. Siehe hierzu „Montage“. • Füllen Sie mehr Wäsche ein. Die Beladung ist möglicherweise zu gering. Die Programmdauer erhöht oder verringert sich während der Ausführung des Programms.
DEUTSCH VORSICHT! Verletzungsgefahr! Vergewissern Sie sich, dass die Trommel sich nicht dreht. Warten Sie sonst, bis die Trommel zum Stillstand gekommen ist. 39 2. Ziehen Sie den Netzstecker aus der Netzsteckdose. 3. Öffnen Sie die Filterklappe. 4. Drücken Sie den Auslöser für die Notfallentriegelung nach unten und öffnen Sie gleichzeitig die Gerätetür. Stellen Sie sicher, dass der Wasserstand in der Trommel nicht zu hoch ist.
www.aeg.com Programme Beladung (kg) Standardprogramm Baumwolle 60°C Standardprogramm Baumwolle 60°C Standardprogramm Baumwolle 40°C EnergieWasserUngefähverbrauch verbrauch re Pro(kWh) (Liter) grammdauer (in Minuten) Restfeuchte (%)1) 9 0.60 54 238 44 4.5 0.37 39 191 44 4.5 0.36 40 190 44 1) Am Ende der Schleuderphase. Aus-Zustand (W) Ein-Zustand (W) 0.30 0.
DEUTSCH 41 16. ZUBEHÖR 16.1 Verfügbar bei www.aeg.com/shop oder einem autorisierten Händler Nur mit geeignetem, von AEG zugelassenem Zubehör können die Sicherheitsstandards des Geräts gewährleistet werden. Werden nicht zugelassene Teile verwendet, erlischt jeglicher Gewährleistungsanspruch. 16.2 Satz Fixierplatten Wenn Sie das Gerät auf einem Sockel aufstellen, befestigen Sie es mithilfe der Fixierplatten. Lesen Sie die mit dem Zubehör gelieferte Gebrauchsanleitung sorgfältig durch.
www.aeg.com 17. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte. Entsorgen Sie * Geräte mit diesem Symbol nicht mit dem Hausmüll. Bringen Sie das Gerät zu Ihrer örtlichen Sammelstelle oder wenden Sie sich an Ihr Gemeindeamt.
DEUTSCH 43
157004461-A-052017 www.aeg.