L8FEC68SP USER MANUAL PL Instrukcja obsługi Pralka
www.aeg.com SPIS TREŚCI 1. INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA..............................................3 2. WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA...............................................4 3. INSTALACJA........................................................................................................ 6 4. OPIS URZĄDZENIA............................................................................................11 5. PANEL STEROWANIA............................................................
POLSKI 1. 3 INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA Przed przystąpieniem do instalacji i rozpoczęciem eksploatacji urządzenia należy uważnie zapoznać się z załączoną instrukcją obsługi. Producent nie odpowiada za obrażenia ciała ani szkody spowodowane nieprawidłową instalacją lub eksploatacją urządzenia. Należy zachować instrukcję obsługi w bezpiecznym i łatwo dostępnym miejscu do wykorzystania w przyszłości. 1.
www.aeg.com • • • • • • • • • Nie należy przekraczać maksymalnego ciężaru ładunku, który wynosi 8 kg (patrz „Tabela programów”). Ciśnienie robocze wody w punkcie podłączenia powinno wynosić od 0,5 bara (0,05 MPa) do 8 barów (0,8 MPa). Wykładzina podłogowa, dywan lub mata podłogowa nie mogą zasłaniać otworów wentylacyjnych w podstawie (jeśli dotyczy).
POLSKI • • • • • • • • Należy postępować zgodnie z instrukcją instalacji dołączoną do urządzenia. Nie instalować ani nie korzystać z urządzenia w miejscach, w których temperatura może spaść poniżej 0°C lub w których mogłoby być ono narażone na działanie czynników atmosferycznych. Podłoże, na którym będzie stało urządzenie, musi być płaskie, stabilne, odporne na działanie wysokiej temperatury i czyste. Zapewnić odpowiednią cyrkulację powietrza pomiędzy urządzeniem i podłogą.
www.aeg.com • włożeniem do pralki należy taką odzież wyprać wstępnie ręcznie. Nie dotykać szklanych drzwi podczas trwania programu. Szyba może być gorąca. 2.5 Serwis • • Należy skontaktować się z autoryzowanym punktem serwisowym, który naprawi urządzenie. Należy stosować wyłącznie oryginalne części zamienne. • • • • Odłączyć urządzenie od źródła zasilania i zamknąć dopływ wody. Odciąć przewód zasilający blisko urządzenia i oddać do utylizacji.
POLSKI 5. Ostrożnie położyć na nim urządzenie na tylnej ściance. 6. Położyć przedni styropianowy element opakowania na podłodze pod urządzeniem. 7 UWAGA! Nie stosować alkoholu, rozpuszczalników ani produktów chemicznych. 9. Odpowiednio dopasować położenie listew wygłuszających. Patrz ilustracja: A Uważać, aby nie uszkodzić węży. 7. Usunąć blok styropianu ze spodu urządzenia. B • A (PRZÓD) = przód urządzenia • B (TYŁ) = tył urządzenia 10. Usunąć samoprzylepne paski z listew wygłuszających. 11.
www.aeg.com Listwy wygłuszające należy przyklejać w temperaturze pokojowej. 13. Podnieść urządzenie do pozycji pionowej. Zaleca się zachowanie opakowania oraz blokad transportowych na przyszłość. 14. Zdjąć przewód zasilający i wąż spustowy z uchwytów. Z węża spustowego może wypłynąć woda. Jest to rezultat testów z użyciem wody przeprowadzanych w fabryce. 15. Odkręcić trzy śruby kluczem dołączonym w komplecie z urządzeniem. 16. Wyciągnąć plastikowe rozpórki. 17.
POLSKI 9 Urządzenie musi być wypoziomowane i stabilne. Prawidłowe wypoziomowanie urządzenia eliminuje drgania, hałas oraz ruchy urządzenia podczas pracy. UWAGA! Sprawdzić, czy nie ma wycieków ze złączek. 3.3 Wąż dopływowy 1. Podłączyć wąż dopływowy z tyłu urządzenia. 2. Skierować go w prawo lub w lewo, odpowiednio do położenia zaworu wody. Nie stosować węży przedłużających, jeśli wąż dopływowy jest za krótki. Należy skontaktować się z punktem serwisowym, aby zamówić dłuższy wąż dopływowy. 3.
www.aeg.com Wąż spustowy można podłączyć na różne sposoby: 1. Zagiąć wąż na kształt litery U i poprowadzić go wzdłuż plastikowej prowadnicy węża. 2. Na krawędzi umywalki – Przymocować prowadnicę do zaworu wody lub do ściany. Uwaga: plastikowa prowadnica nie może poruszać się podczas odpompowywania wody. Sprawdzić, czy wąż spustowy nie jest zanurzony w wodzie. Może nastąpić cofnięcie brudnej wody do urządzenia. 3.
POLSKI Należy ułożyć wąż spustowy w pętlę, aby nie dopuścić do przedostawania się zanieczyszczeń ze zlewu do urządzenia. 6. Włożyć wąż bezpośrednio do rury kanalizacyjnej zabudowanej w ścianie i zabezpieczyć obejmą. 11 Wąż spustowy można przedłużyć maksymalnie do 400 cm. Więcej informacji na temat innych węży spustowych i przedłużających można uzyskać w autoryzowanym punkcie serwisowym. 4. OPIS URZĄDZENIA 4.
www.aeg.com 4.2 Widok urządzenia 1 2 3 9 8 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Blat roboczy Dozownik detergentu Panel sterowania Uchwyt drzwi Tabliczka znamionowa Filtr pompy opróżniającej Nóżki do poziomowania urządzenia 8 9 10 11 12 Wąż spustowy Podłączenie węża dopływowego Przewód zasilający Blokady transportowe Uchwyt węża 5. PANEL STEROWANIA 5.
POLSKI 1 Pokrętło wyboru programów 2 Wyświetlacz 3 Przycisk dotykowy oszczędzania energii (Eco) 4 Przycisk dotykowy oszczędzania czasu (Skrócenie czasu) 5 Przycisk dotykowy pominięcia fazy (Opcja) • Pominięcie fazy prania (Tylko • płukanie) Pominięcie fazy prania i płukania • (Tylko wirowanie) Tylko odpompowanie (Tylko odpompowanie) 6 Przycisk dotykowy Start/Pauza (Start/Pauza) 13 7 Przycisk dotykowy dodatkowego płukania (Dodatkowe płukanie) 8 Przycisk dotykowy opóźnienia rozpoczęcia programu (Opóźni
www.aeg.com Wskaźnik cyfrowy może pokazywać: • Czas trwania programu (np. • Czas opóźnienia programu (np. • Zakończenie cyklu ( ). • Kod ostrzeżenia (np. ). lub ). ). Wskaźniki trybu energooszczędnego. Wskaźnik pojawia się w przypadku wyboru programu do prania bawełny w temperaturze 40°C lub 60°C. Wskaźnik fazy prania: miga podczas fazy prania wstępnego i zasadni‐ czego. Wskaźnik fazy płukania: miga podczas fazy płukania. Wskaźnik pojawia się, gdy włączono opcję Soft Plus.
POLSKI 15 6. POKRĘTŁO I PRZYCISKI 6.1 Wł./Wył. Naciśnięcie tego przycisku przez kilka sekund umożliwia włączenie lub wyłączenie urządzenia. Podczas włączania i wyłączania urządzenia emitowane są dwa różne dźwięki. • W niektórych przypadkach funkcja Tryb czuwania automatycznie wyłącza urządzenie, aby zmniejszyć pobór energii. Należy wtedy ponownie włączyć urządzenie. Więcej informacji znajduje się w rozdziale Codzienna eksploatacja. 6.
www.aeg.com Na wyświetlaczu pojawi się odpowiedni wskaźnik. • Odplamianie Tę opcję należy wybrać do prania wstępnego silnie zabrudzonej lub zaplamionej odzieży z zastosowaniem odplamiacza. Dodać odplamiacz do przegródki . Odplamiacz jest mieszany i podgrzewany z detergentem w celu zwiększenia jego wydajności. Opcja ta może wydłużyć czas trwania programu. Funkcja nie jest dostępna z temperaturą niższą niż 40°C.
POLSKI Jeśli wybrano program Bawełniane z temperaturą 40°C lub 60°C, na wyświetlaczu pojawi się wskaźnik . Są to najbardziej wydajne programy do prania tkanin bawełnianych pod względem całkowitego zużycia wody i energii. 6.9 Skrócenie czasu Ta opcja umożliwia skrócenie czasu trwania programu. • W przypadku średnio lub lekko zabrudzonego prania można skrócić program prania. Dotknąć przycisku jednokrotnie, aby skrócić czas trwania.
www.aeg.com Program Bawełniane Opis programu Białe i kolorowe tkaniny bawełniane. Średnio i lekko zabru‐ dzone. Standardowe programy do określenia parametrów eks‐ ploatacyjnych dla klasy energetycznej. Zgodnie z rozporzą‐ dzeniem 1061/2010 programy Bawełniane 60°C oraz Baweł‐ niane 40°C z opcją są odpowiednikami programów: „standardowy program prania tkanin bawełnianych w 60°C” i „standardowy program prania tkanin bawełnianych w 40°C”.
POLSKI Program Antyalergiczne 20 min. - 3 kg 19 Opis programu Białe rzeczy bawełniane. Program usuwa mikroorganizmy dzięki fazie prania, w której przez kilka minut utrzymuje się temperatura powyżej 60°C. Pozwala to usunąć zarazki, bakte‐ rie, mikroorganizmy i cząstki stałe. Dodatkowa faza płukania zapewnia skuteczne usunięcie resztek detergentu oraz pyłków i alergenów. Dzięki temu pranie jest skuteczniejsze. Rzeczy bawełniane i syntetyczne, lekko zabrudzone lub no‐ szone jeden raz.
www.aeg.com Temperatura programu, maksymalna prędkość wirowania i maksymalny wsad Program Temperatura do‐ myślna Zakres temperatur Maksymalna pręd‐ Maksymalny kość wirowania wsad Zakres prędkości wi‐ rowania Bawełniane 40°C 95°C - pranie w zim‐ nej wodzie 1600 obr./min 1600 obr./min - 400 obr./min 8 kg Syntetyczne 40°C 60°C - pranie w zim‐ nej wodzie 1200 obr./min 1200 obr./min - 400 obr./min 3 kg Delikatne 40°C 40°C - pranie w zim‐ nej wodzie 1200 obr./min 1200 obr./min - 400 obr.
POLSKI 21 Antyalergiczne ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Odplamianie1) ■ ■ ■ ■ ■ Pranie wstępne ■ ■ ■ ■ ■ Dodatkowe płu‐ kanie ■ ■ ■ ■ ■ Eco 2) ■ ■ ■ Skrócenie czasu 3) ■ ■ ■ Tylko płukanie ■ ■ ■ ■ ■ ■ ■ ■ ■ Tylko wirowanie ■ ■ ■ ■ ■ ■ ■ ■ ■ Tylko odpompo‐ wanie ■ ■ ■ ■ ■ ■ ■ ■ ■ Opóźniony start ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Para+ 1) Soft Plus ■ Jeans ÖKOPower ■ Outdoor Delikatne ■ 20 min.
www.aeg.com 7.2 Woolmark Apparel Care – Green (zielony) urządzeniu jako nadający się do prania odzieży wełnianej oznaczonej metką „prać ręcznie”, pod warunkiem, że pranie będzie wykonane zgodnie z zaleceniami producenta pralki. Należy stosować się do informacji dotyczących suszenia oraz pozostałych wskazówek zamieszczonych na metce odzieży. M1636 W Wielkiej Brytanii, Irlandii, Hong Kongu i Indiach symbol Woolmark jest certyfikowanym znakiem towarowym.
POLSKI przytrzymać przyciski Płukanie+ i Opóźniony start przez około 6 sekund. Po wyłączeniu sygnałów dźwiękowych będą one nadal emitowane podczas nieprawidłowego działania urządzenia. 9.4 Soft Plus Ustawić opcję Soft Plus, aby optymalnie dozować płyn zmiękczający do tkanin i zapewnić miękkość tkanin. Zaleca się to w przypadku używania płynu zmiękczającego do tkanin. Opcja ta nieznacznie wydłuża czas trwania programu. 9.
www.aeg.com 10.3 Stosowanie detergentów i dodatków 1 2 3. W przypadku detergentu w proszku ustawić klapkę w górnym położeniu. Przegródka na detergent do fazy prania wstępnego, programu namaczania lub na odplamiacz. Przegródka na detergent do fazy prania. Przegródka na dodatkowe środki w płynie (płyn zmiękczający, krochmal). Oznaczenie maksymalnego poziomu dodatków w płynie. Klapka do detergentu w proszku lub w płynie.
POLSKI Klapka w DOLNYM położeniu: • Nie stosować gęstych ani żelowych detergentów. • Nie wlewać więcej detergentu w płynie, niż wskazuje oznaczenie na klapce. • Nie ustawiać fazy prania wstępnego. • Nie ustawiać funkcji opóźnienia rozpoczęcia programu. 5. Odmierzyć odpowiednią ilość detergentu i płynu zmiękczającego. 6. Zamknąć dobrze dozownik detergentu. 25 3. W razie potrzeby można wybrać jedną lub więcej opcji, dotykając odpowiednich przycisków.
www.aeg.com 1. Dotknąć przycisku Start/Pauza, aby włączyć tryb pauzy. Zacznie migać odpowiedni wskaźnik. 2. Dotykać przycisku Opóźniony start, aż na wyświetlaczu pojawi się . 3. Ponownie dotknąć przycisku Start/ Pauza, aby natychmiast uruchomić program. W takim przypadku w ciągu 30 sekund można wstrzymać pracę urządzenia i wyjąć z bębna kilka rzeczy.
POLSKI Jeśli wybrano Para+, włączają się wskaźniki fazy parowej. Trwa faza parowa: 10.12 Otwieranie drzwi Jeśli temperatura i poziom wody w bębnie są zbyt wysokie lub bęben nadal obraca się, nie można otworzyć drzwi. . Trwa faza chroniąca przed zagnieceniami: . 10.10 Przerywanie programu i zmiana opcji W czasie trwania programu można zmienić tylko niektóre opcje: 1. Dotknąć przycisku Start/Pauza. Zacznie migać odpowiedni wskaźnik. 2. Zmienić opcje.
www.aeg.com 4. Nacisnąć i przytrzymać przez kilka sekund przycisk Wł./Wył., aby wyłączyć urządzenie. 4. Drzwi oraz dozownik detergentu należy pozostawić lekko uchylone, aby zapobiec powstawaniu pleśni i nieprzyjemnych zapachów. 5. Zakręcić zawór wody. W każdym przypadku urządzenie automatycznie odpompuje wodę po około 18 godzinach. 10.
POLSKI • • • • • • • Opróżnić kieszenie i rozłożyć zwinięte tkaniny. Odwrócić na drugą stronę wielowarstwowe tkaniny, wełnę oraz rzeczy z nadrukami. Usunąć uporczywe plamy. Przeprać uporczywe plamy specjalnym detergentem. Należy zachować ostrożność przy obchodzeniu się z zasłonami. Odczepić żabki/haczyki i umieścić zasłony w worku do prania lub poszewce od poduszki. Nie prać rozdartych tkanin lub tkanin o nieobszytych brzegach. Małe i/lub delikatne rzeczy (np.
www.aeg.com 12. KONSERWACJA I CZYSZCZENIE OSTRZEŻENIE! Patrz rozdział dotyczący bezpieczeństwa. 12.1 Czyszczenie obudowy Urządzenie należy czyścić wyłącznie za pomocą ciepłej wody z łagodnym mydłem. Dokładnie osuszyć wszystkie powierzchnie. regularnie (co najmniej raz w miesiącu) wykonać pranie konserwacyjne: 1. Wyjąć pranie z bębna. 2. Uruchomić program do prania bawełny z najwyższą temperaturą i dodać niewielką ilość detergentu w proszku. 12.
POLSKI 31 1. Otworzyć szufladę. Nacisnąć rygiel do dołu, jak pokazano na ilustracji, i wyjąć szufladę. 1 2 2. Zdjąć górną część przegródki na dodatki, aby ułatwić czyszczenie, i przepłukać pod bieżącą ciepłą wodą w celu usunięcia pozostałości nagromadzonego detergentu. Po umyciu założyć górną część w odpowiednim miejscu. 12.7 Czyszczenie pompy opróżniającej OSTRZEŻENIE! Wyjąć wtyczkę przewodu zasilającego z gniazda elektrycznego.
www.aeg.com 6. Powtarzać czynności opisane w punktach 4 i 5, aż woda przestanie wypływać. 7. Obrócić filtr w kierunku przeciwnym do ruchu wskazówek zegara, aby go wyjąć. 2 1 2. Pod otworem dostępowym umieścić odpowiednie naczynie do zebrania wypływającej wody. 3. Otworzyć w dół rynienkę. Dobrze jest mieć w pobliżu szmatkę do wycierania wody wyciekającej podczas odkręcania filtra. 1 2 8. W razie potrzeby usunąć włókna i inne zanieczyszczenia z wnęki filtra. 9.
POLSKI 33 1 2 3 2. Wyjąć wąż dopływowy z urządzenia, odkręcając nakrętkę. 12. Zamknąć pokrywę pompy. 2 1 Po spuszczeniu wody przy użyciu procedury awaryjnej należy ponownie uruchomić układ odpływowy: a. Wlać 2 litry wody do przegródki na detergent do prania zasadniczego dozownika detergentu. b. Uruchomić program, aby odpompować wodę. 3. Filtr zaworu z tyłu urządzenia należy czyścić za pomocą szczoteczki do zębów. 12.
www.aeg.com osiągnąć 0°C lub spaść poniżej, należy usunąć pozostałą wodę z węża dopływowego oraz z pompy opróżniającej. 45° 20° 12.9 Awaryjne spuszczanie wody Jeśli urządzenie nie spuszcza wody, należy przeprowadzić taką samą procedurę, jak opisano w rozdziale „Czyszczenie filtra odpływowego”. W razie potrzeby wyczyścić pompę. 1. Wyjąć wtyczkę przewodu zasilającego z gniazda elektrycznego. 2. Zakręcić zawór wody. 3. Umieścić dwa końce węża dopływowego w zbiorniku i odczekać, aż woda spłynie z węża.
POLSKI Jeśli urządzenie jest przepełnione, należy wyjąć część rzeczy z bębna i/lub dociskając drzwi, nacisnąć jednocześnie przycisk Start/Pauza, aż wskaźnik przestanie migać (patrz poniższa ilustracja). 35 • – Zasilanie jest niestabilne. Odczekać do czasu ustabilizowania się zasilania. • – Brak komunikacji między podzespołami elektronicznymi urządzenia. Wyłączyć urządzenie i włączyć je ponownie. • – Włączyło się zabezpieczenie przed zalaniem. Odłączyć urządzenie i zamknąć zawór wody.
www.aeg.com Problem Możliwe rozwiązanie • • • Urządzenie nie wypom‐ powuje wody. • • • Nie włącza się faza wiro‐ wania lub cykl prania trwa dłużej niż zwykle. • • • • Wyciek wody na podło‐ gę. • • • Nie można otworzyć drzwi urządzenia. • • • • • Urządzenie wydaje niety‐ • powe dźwięki i wibruje. • Czas trwania programu wydłuża się lub skraca podczas trwania progra‐ mu. • Upewnić się, że syfon umywalki jest drożny. Upewnić się, że wąż spustowy nie jest zagięty ani przygnie‐ ciony.
POLSKI Problem Efekty prania są niezado‐ walające. Nadmierna ilość piany w bębnie podczas cyklu prania. 37 Możliwe rozwiązanie • • • • Zwiększyć ilość lub użyć innego detergentu. Użyć specjalnych środków do usuwania uporczywych plam przed praniem. Należy sprawdzić, czy ustawiono prawidłową temperaturę. Zmniejszyć ilość prania. • Zmniejszyć ilość detergentu. • Po zakończeniu prania w szufladzie na detergenty zostają resztki detergen‐ • tu.
www.aeg.com 5. Wyjąć pranie i zamknąć drzwi urządzenia. 6. Zamknąć pokrywę filtra. 14. PARAMETRY EKSPLOATACYJNE Podane wartości uzyskano w warunkach laboratoryjnych zgodnie z od‐ powiednimi standardami. Różne czynniki, takie jak ilość i rodzaj prania oraz temperatura otoczenia, mogą wpływać na zmianę tych wartości. Czas trwania programu może również zależeć od ciśnienia wody, napię‐ cia zasilania oraz temperatury doprowadzanej wody.
POLSKI Programy Wsad (kg) Bawełniane 40°C – program standardowy 4 Zużycie energii (kWh) Zużycie wody (li‐ try) 0.35 39 Przybliżo‐ Wilgot‐ ny czas ność trwania (%)1) programu (minuty) 45 232 44 1) Po zakończeniu fazy wirowania. Tryb wyłączenia (W) Tryb czuwania (W) 0.30 0.30 Podane wyżej informacje są zgodne z rozporządzeniem 1015/2010 Komisji UE, wdrażają‐ cym dyrektywę 2009/125/WE 15.
www.aeg.com 16. AKCESORIA 16.1 Dostępne także na stronie www.aeg.com/shop lub u autoryzowanego sprzedawcy Jedynie używanie odpowiednich akcesoriów zatwierdzonych przez firmę AEG zapewni spełnienie norm bezpieczeństwa przez urządzenie. Użycie niezatwierdzonych będzie powodem negatywnego rozpatrzenia reklamacji. 16.2 Zestaw płytek mocujących odpowiedniego zestawu łączącego zatwierdzonego przez firmę AEG. Zestaw łączący powinien być dopasowany do głębokości urządzeń.
POLSKI 41 zwrócić produkt do miejscowego punktu ponownego przetwarzania lub skontaktować się z odpowiednimi władzami miejskimi. chronić środowisko naturalne oraz ludzkie zdrowie. Nie wolno wyrzucać urządzeń oznaczonych symbolem razem z odpadami domowymi.
www.aeg.
POLSKI 43
157002702-B-362017 www.aeg.