L8FEC9412N USER MANUAL ZH 用户手册 洗衣机
www.aeg.com 内容 1. 安全信息................................................................................................................2 2. 安全说明................................................................................................................4 3. 安装.......................................................................................................................5 4. 产品说明................................................................................................................9 5.
中文 3 担任何责任。请妥善保管操作说明,并置于易于取用的地 方,供将来参考之用。 1.1 儿童及弱势群体安全 • • • • • • • • • 本机可供 8 岁及以上儿童和肢体伤残、感官或精神上有 障碍或缺乏相关经验及知识的人士使用,前提是他们在 使用本机时受到监督或得到安全使用指导,同时了解使 用过程中可能存在的危险。 3 至 8 岁的儿童以及身患大范围复杂残疾的人员应远离 本机,除非始终有人在旁监督。 除非有成人始终在旁监督,否则 3 岁以下儿童应远离本 机。 请勿让儿童玩弄本机。 所有包装物都必须远离儿童,且予以妥善处置。 洗衣剂应远离儿童。 当机门处于打开状态时,勿让儿童和宠物靠近本产品。 如果本机配备儿童安全装置,则应将其打开。 在无人监管的情况下,儿童不能擅自清理和维护本机。 1.2 一般安全信息 • • • • • • • • • • 请勿更改本机规格。 请勿超过 9 公斤的最大装载量(参阅“程序表”章节)。 出口接头处进水口的工作水压必须介于 0.5 巴 (0.05 兆 帕) 到 8 巴 (0.
www.aeg.com 2. 安全说明 2.1 安装 安装必须符合相关的国家法 规。 • • • • • • • • • • • • • 拆掉所有包装和运输螺栓,包括橡胶套 和塑料垫片。 请将运输螺栓放在安全的地方。如果 日后要移动本机,必须将其重新连接锁 住滚筒以防止内部损坏。 设备非常重,搬运时请注意。请始终佩 戴安全手套和配套的鞋子。 请勿安装或使用已损坏的设备。 按照本机附带的安装说明书操作。 请勿在温度低于 0°C 或露天的地方安 装或使用本机。 安装本机的地面区域必须平稳,耐热且 干净。 确保本机与地面之间有空气流通。 在将本机放置在永久位置后,使用水平 仪帮助检查其是否完全水平。若不是, 可对机脚进行相应调整。 请勿直接将本机安装在地漏上。 请勿将水喷洒到本机上,也不要将它置 于湿度过高的环境。 请勿在无法完全打开机门的地方安装 本机。 请勿在本机下方放置关闭的容器来收 集可能漏出的水。应联系授权服务中 心确认可以使用哪些配件。 • 2.
中文 5 3. 安装 警告! 请参阅“安全”一章。 3.1 拆除包装 警告! 在安装本机之前,请移除所有 包装材料和运输螺栓。 警告! 戴上手套。 警告! 背面朝上放下本机之后, 等待 6 小时之后再使用本机。 6 小时之后压缩机才可正常工 作。 4. 打开机门,从机门密封条上取下聚苯乙 烯条,以及滚筒中的所有物品。 1. 揭下外膜。如有必要,可使用刀具。 5. 小心地将本机放倒,并使其后部压在包 装材料上。 6. 将前面的聚苯乙烯包装成份放在本机 下面的地板上。 2. 取下纸板顶部和聚苯乙烯包装材料。 确保不会对软管造成损害。 3. 揭下内膜。 7.
www.aeg.com 8. 彻底清洁并干燥本机底部。 14. 从软管支架上取下电源线和排水软管。 警告 勿使用酒精、溶剂或化学品。 9. 确保识别声障的不同大小和位置。请 参考插图: A 可能会有水从排水管中流出。 这是因为工厂里对本机所做 的水流测试。 15. 使用本机随附的钥匙移除三个螺栓。 B • A(正面)= 本机的正面 • B(背面)= 本机的背面 10. 从静音声障上取下胶条。 11. 将四个声障安装到本机底部。 12. 请参考插图。确保声障都已牢牢固定。 x4 16. 抽出塑胶垫片。 17. 将用户手册袋中找到的塑料盖放入洞 中。 A B 在室温下吸附声障。 13.
中文 我们建议您保留包装和运输 螺栓,以便在移动本机时使 用。 3.2 定位和调平 7 3.3 进水软管 1. 将进水软管连接到本机背部。 2. 将它向左或向右放置,具体取决于水龙 头的位置。 1. 将本机安装在平整的硬地面上。 确保地毯不会阻止本机下面 的空气流通。 确保本机不会触碰到墙壁或 其他装置。 2. 拧松或拧紧机脚以调整水平位置。 警告! 调整水平位置时,请勿将本机 置于纸板、木头或位于本机机 脚下的材料上。 45 20 O O 确保进水管不是垂直位置。 3. 如有必要,可松开圆形螺母,将它固定 在正确的位置上。 4. 将进水软管连接到带有 3/4 英寸螺纹 接头的冷水龙头上。 x4 本机必须位于水平且稳定的位置。 正确调整本机位置可防止本 机在使用过程中发生震动、噪 音以及移动的情况。 当本机安装在底座上,或者洗 衣烘干机堆放在洗衣机上,请 使用“配件”一章描述的配件。 请仔细阅读与本机和配件一 起提供的说明。 警告 确保接头处不会发生泄漏。 如果进水软管过短,请勿使用 加长软管。请与服务中心联 系,以更换进水软管。 3.
www.aeg.com 3. 流向带有通风孔的立管 - 将排水管直 接插入排水管道中。请参考插图。 A 如果发生这种情况,请关闭水龙头,联系 授权服务中心以更换软管。 3.5 排水 排水管距离地板的高度不低于 60 厘米,且 不超过 100 厘米。 排水软管最多可以加长到 400 厘米。要获得另外的排 水软管和加长软管,请与授权 服务中心联系。 可以用不同的方式连接排水管: 排水软管的末端必须保持通 风,即排水管道的内径 (最小 38 毫米 - 最小 1.5 英 寸)必须大于排水软管的外 径。 4. 如果排水管末端变成这样(参见图片), 您可以将它直接推进立管里。 1. 让排水管摆成 U 型,并将它放在塑料 软管导向装置周围。 2. 在水槽边上 - 将软管导向装置固定到 水龙头或墙壁上。 确保塑料管托在本机排水时 不会移动。 确保排水管末端没有浸入水 中。可能会有脏水回流至本 机。 5. 没有塑料软管导向装置,流向水槽栓 将排水软管插入栓中,并用夹钳将它拧 紧。请参考插图。 确保排水软管形成一个环,以 防止水槽中的颗粒物进入本 机。 6.
中文 9 4. 产品说明 4.1 特殊功能 • 新的洗衣机满足各项现代要求,即用少量 水、能耗和洗涤剂可高效处理衣物,同时 使衣物得到妥善的护理。 • • Oko-Mix 技术 可预先混合不同的阶 段,首先在水中溶解洗涤剂和衣物柔顺 剂,然后将它们分布到衣物中,从而保 护衣物纤维。因此,可深入到每一根纤 维并提供精心护理。 ProSense 技术可检测衣物量,在 30 秒内确定程序持续时间。根据衣物量 和纤维类型定制洗涤程序,不会浪费更 多不必要的时间、能耗和水。 • • 要让衣物焕然一新,蒸汽处理既简单又 快捷。温和的蒸汽程序可去除异味,减 少干燥衣物中的褶皱,从而减少熨烫工 作。 易熨烫 选项在每个程序结束时会有温 和的蒸汽,使衣物舒展并减少衣物褶 皱。熨烫会更加轻松! 去污 选项会预先处理顽固的污渍,优化 去污剂的效果。 使用 软化升级 选项,可将衣物柔顺剂 均匀地喷洒到衣物上,并深入渗透到衣 物纤维中,让衣物变得更加柔顺。 4.
www.aeg.com 9 进水软管连接 10 电源电缆 11 运输螺栓 12 软管支架 5. 控制板 5.1 控制板说明 3 2 1 4 5 13 12 11 10 9 8 7 6 1 程序旋钮 2 显示屏 3 节能按触按钮 (节能) 7 额外漂洗按触按钮 (额外漂洗) 4 省时按触按钮 (省时) 10 防污和预洗按触按钮 (去污/预洗) 8 延迟启动按触按钮 (预约) 9 超级蒸汽按触按钮 (易熨烫) 5 跳过阶段按触按钮 (选项) • 跳过洗涤阶段 (单漂洗) • 跳过洗涤和漂洗阶段 (单脱水) • 单排水 (单排水) 6 启动/暂停按触按钮 (启动/暂停) 5.
中文 最大衣物量指示灯。预计衣物量时, “PROSENSE 衣物量检测”一节)。 11 图标会闪烁(请参阅 最大衣物量指示灯。当衣物量超过选定程序声明的最大衣物量时,它会闪 烁。 延迟开始指示灯。 机门已锁指示灯。 数字指示灯可以显示: • 程序持续时间(例如 • 延迟时间(例如 • 程序结束 ( )。 • 警告代码(例如 )。 或 )。 )。 节能指示灯。选择适用于 40 °C 或 60 °C 的棉织物程序时, 会显示。 洗涤阶段指示灯:在预洗和洗涤阶段它会闪烁。 漂洗阶段指示灯:它会在漂洗阶段闪烁。 软化升级 选项激活时,显示 指示灯。 脱水和排水阶段指示灯。在脱水和排水阶段它会闪烁。 MIX OKO MIX 指示灯。 蒸汽阶段指示灯。 防皱处理阶段指示灯。 儿童安全锁指示灯。 省时指示灯。 温度指示灯。设置冷水洗时,显示 脱水速度指示灯。 延迟漂洗指示灯。 静音指示灯。 预洗指示灯。 污渍指示灯。 指示灯。 指示灯
www.aeg.com 额外漂洗指示灯。 6. 旋钮和按钮 6.1 开/关 按触此按钮并停留几秒钟,可激活或停用 本机。打开或关闭本机时会有两种不同的 声音。 • 有时候,您可能需要再次启动本机,待机 功能可自动停用本机以降低能耗。 有关更多信息,请参阅“日常使用”一章中 的“待机”一节。 6.2 简介 并非所有洗涤程序都可选择 某些选项/功能。在“程序表” 一节检查选项/功能与洗涤程 序之间的兼容性。一个选项/ 功能可能与另一个相互排斥, 如果是这种情况,本机不允许 您同时设置不兼容的选项/功 能。 确保触摸屏和按触按钮始终 清洁干燥。 6.3 温度 选择一个洗涤程序时,本机会自动提议一 个默认温度。 显示屏上将显示指示灯 。 机门保持锁定状态。滚筒定时旋转,以 减少起皱。您必须打开机门将水排出。 按触 启动/暂停 按钮:本机仅执行排水 阶段。 本机大约会在 18 小时之后自 动将水排空。 6.
中文 6.6 额外漂洗 6.9 省时 根据选定的洗涤程序,利用此选项最多可 添加 3 次漂洗。 使用此选项可缩短程序持续时间。 适用于对洗衣剂过敏的人群以及水质较软 的地区。 指示灯显示选择的漂洗次数。 此选项会延长程序持续时间。 • • 洗涤程序,显示屏会显示 。 此时按触 额外漂洗 按钮,可 以只添加一次漂洗。 6.7 易熨烫 洗涤程序结束后,会有一个短暂的防皱处 理阶段,而此选项会在防皱处理阶段之后 添加一个蒸汽阶段。 蒸汽阶段可减少衣物起皱,并帮助衣物熨 烫。 在蒸汽阶段,显示屏上的指示灯 烁。 会闪 此选项会延长程序持续时间。 程序停止时,显示屏显示一个零 ,指示 灯 保持稳定,且指示灯 开始闪烁。 滚筒平稳运行约 30 分钟,以保持蒸汽效 果。按触任何按钮可停止防皱处理,机门 打开。 较小的衣物量有助于达到更 好的效果。 。 也可使用此选项缩短 蒸汽 程 序持续时间。 6.
www.aeg.com 7. 程序 7.
中文 程序 15 程序说明 请勿使用衣物柔顺剂,确保洗涤剂投放盒中没 有柔顺剂残留物。 户外 户外衣物,技术织物、运动衣物、防水透气夹克、带有可拆卸 抓绒或保温内胆的紧身夹克。建议的衣物量为 2.
www.aeg.com 程序 默认温度 温度范围 最大脱水转速 脱水速度范围 最大衣物量 20 分鈡-3 公斤 30 °C 40 °C - 30 °C 1200 转/分 3 千克 1200 转/分 - 400 转/分 户外 30 °C 40 °C - 冷洗 1200 转/分 2.
■ ■ 17 羽绒被 户外 20 分鈡-3 公斤 抗过敏 ■ 经济洗 ■ 蒸汽 精细 ■ 羊毛/丝绸 化纤 软化升级 棉织物 中文 ■ 1) 温度低于 40 °C 时,不可使用此选项。 2) 该选项在温度低于 30 °C 时不可用。 3) 如果设定了更短的持续时间,建议您减少衣物量。本机可以满载放入衣物,但这样会降低洗涤效果。 7.2 Woolmark Apparel Care - 绿色 本机的毛织品洗涤程序已通过 The Woolmark Company(国际羊毛局)测试和认可,适用于 洗涤标有“手洗”字样的羊毛针织衣物,只要按 照由该洗衣机制造商发布的说明洗涤衣物即 可。按照衣物护理标签进行烘干并遵循其他洗 衣说明。M1361 羊毛标记符号是在许多国家/地区的认证标记。 8. 初次使用前 在安装过程中或者初次使用 前,可能会发现本机内有一些 水。这是工厂执行全面的功 能测试时留下的水,执行功能 测试是为了确保本机交付到 客户时可正常运行,且没有后 顾之忧。 1. 确保取下本机上的所有运输螺栓。 2. 确保电源可用并打开水龙头。 3.
www.aeg.com • • • • • • 启动本机(特殊的短音)。 停用本机(特殊的短音)。 按触按钮(咔哒声)。 做出了错误的选择(3 个短音)。 程序完成(大约 2 分钟的音串)。 本机发生故障(一串短音,大约持续 5 分钟)。 要在程序完成时停用/启用声音信号,请同 时按触 额外漂洗 和 预约 按钮并保持大约 6 秒钟。 禁用声响信号功能后,机器发 生故障时仍会继续发出声响 信号。 • 要启用/停用此选项,请同时按触 额外 漂洗 按钮和 选项 按钮,直到相关指示 灯亮起/熄灭。 此选项会添加两次漂洗,且显示屏显示 。 9.4 软化升级 设置 软化升级 选项,以优化衣物柔顺剂分 配并提高衣物柔软度。 建议在使用衣物柔顺剂时设置此选项。 此选项会略为延长程序持续 时间。 9.3 固定额外漂洗 要启用/停用此选项,请同时按触 温度 按钮 使用此选项,您可在设置程序时永久使用 额外漂洗(若可选择)。 和 脱水 按钮,直到指示灯 指示灯 亮起/熄灭。 上方的 10. 日常使用 警告! 请参阅“安全”一章。 10.1 启动本机 1. 将电源插头插入电源插座。 2.
中文 19 4. 要使用液体洗涤剂,请调低悬板。 用于预洗阶段和浸泡程序的盛载 格。 供洗涤阶段使用的盛载格。 液体添加剂(衣物柔顺剂、衣浆) 的盛载格。 液体添加剂的最大数量水平。 去污剂盛载格。 用于投放粉状或液体洗涤剂的悬 板。 始终遵循洗涤剂产品包装上 的说明,但我们建议您不要 超过指示的最大级别 ( )。但是此数量可保证 获得最好的洗涤效果。 悬板位置位于下方时: • 请勿使用凝胶状或粘 稠的液体洗涤剂。 • 请勿投放超出悬板所 示限额的液体洗涤剂。 • 切勿设定“预洗”阶段。 • 切勿设定“延迟开始”功 能。 5. 量取适量的洗涤剂和衣物柔顺剂。 6. 小心地关闭洗涤剂投放盒。 洗涤程序结束后,如有必 要,可从洗涤剂投放盒中清 理洗涤剂残留物。 10.4 检查悬板的位置 1. 将洗涤剂投放盒完全拉开。 2. 向下按动杠杆,取出投放盒。 1 2 确保悬板不会在您关闭抽屉盒时引起阻 塞。 3. 要使用粉状洗涤剂,请调高悬板。 10.5 设定程序 1.
www.aeg.com 如果不能作出某一选择,不会 有指示灯亮起,也不会发出声 音信号。 10.6 启动程序 按触 启动/暂停 按钮以启动程序。 相关指示灯停止闪烁,并保持亮起。 显示屏中,表示操作阶段的指示灯开始闪 烁,最大衣物量指示灯熄灭。 程序开始时,机门被锁定。显示屏上将显 示标志 。 本机注水之后,排水泵可立即 开始工作。 10.7 启动带延迟开始功能的程 序 1. 反复按触 预约 按钮,直到显示屏显示 亮起。 所需的延迟时间。指示灯 2. 按触 启动/暂停 按钮。 本机会开始延迟开始倒计时。 倒计时完成后,程序将会启动。 PROSENSE 预计在倒计时结 束后开始。 取消延迟在倒计时开始后开始 要取消延迟开始: 1. 按触 启动/暂停 按钮暂停本机。相关 指示灯将闪烁。 2. 反复按触 预约 按钮,直到显示屏显示 。 3. 再次按触 启动/暂停 按钮,立即启动程 序。 更改延迟在倒计时开始后开始 要更改延迟开始: 1. 按触 启动/暂停 按钮暂停本机。相关 指示灯将闪烁。 2. 反复按触 预约 按钮,直到显示屏显示 所需的延迟时间。 3.
中文 21 显示屏上所有洗涤阶段指示灯都变得稳 蒸汽阶段正在运行: . 定,且时间区域显示 。 启动/暂停 按钮的指示灯熄灭。 防皱处理阶段正在运行: . 10.10 中断程序并更改选项 在程序运行时,您只能更改某些选项: 1. 按触按钮 启动/暂停。 相关指示灯将闪烁。 2. 更改选项。显示屏中给定的信息会发 生相应的变化。 3. 再次按触按钮 启动/暂停。 洗涤程序将继续运行。 10.11 取消正在运行的程序 1. 按触 开/关 按钮,取消程序并停用本 机。 2. 再次按触按钮 开/关 以启用本机。 这时,即可设定新的洗涤程序。 如果已经执行 ProSense 阶 段,并且注水已经启动,则新 程序会启动,且不会重复 ProSense 阶段。不会排空 水和洗涤剂,以免造成浪费。 显示屏显示程序的最长持续 时间,并在启动新程序 20 分 钟后更新此时间。 10.12 打开机门 - 添加衣物 当程序或延迟开始运行时,机门将锁定。 如果滚筒内的水温和水位过 高和/或滚筒仍在旋转,将无法 打开机门。 1. 按触按钮 启动/暂停。 在显示屏中,相关机门锁定标志将消失。 2.
www.aeg.com • 按下 开/关 按钮可再次启动本机。 在洗涤程序结束 5 分钟后 按触 开/关 按钮以再次启动本机。 显示屏将显示最后一次设定程序的结 束时间。 旋转程序旋钮以设定新程序。 如果设定了结束时有水留在 滚筒中的程序或选项,待机功 能不会停用本机以提醒您排 水。 11. 建议和提示 警告! 请参阅“安全”一章。 11.3 洗涤剂其他护理 • 11.
中文 23 12. 养护和清洁 警告! 请参阅“安全”一章。 12.1 外部清洁 请仅使用温和的肥皂和温水清洁本机。清 洁后将所有表面完全擦干。 警告 勿使用酒精、溶剂或化学品。 警告 请勿使用氯基洗涤剂清洁金 属表面。 12.2 除垢 如果您所在地区的水质硬度 较高或为中等,建议使用针对 洗衣机的除垢产品。 定期检查滚筒内是否有水垢。 12.5 清洁滚筒 定期检查滚筒,以防止生锈。 要进行彻底的清洁: 1. 使用专用的不锈钢清洁剂来清洁滚筒。 请务必始终遵守产品包装上 的使用说明。 2. 在高温条件下运行时间较短的棉织物 程序,滚筒为空且只使用少量洗涤剂, 以便将剩余的残留物漂洗干净。 12.6 清洁洗涤剂投放盒 为防止干燥的洗涤剂可能出现的沉积,衣 物柔软剂凝块和/或在洗涤剂抽屉中形成霉 块,需要不时地执行以下清洁程序: 1. 打开抽屉。按图中所示向下按卡扣,将 抽屉抽出。 1 普通的洗涤剂中已含有软水剂,但我们仍 建议在排空滚筒之后运行该程序并偶尔使 用除垢产品。 请务必始终遵守产品包装上 的使用说明。 2 12.
www.aeg.com 2 1 4. 将清洁剂抽屉插入导轨,并将其关闭。 滚筒中不放入任何衣物,运行漂洗程 序。 2. 将一个适当的碗置于排水泵接口下方, 以收集从泵中流出的水。 3. 向下打开斜槽。卸下泵过滤器时身边 应准备一块布随时抹干流出来的水。 12.7 清洁排水泵。 4. 逆时针方向旋转过滤器 180 度以将其 打开,但不将其取下。让水流出。 警告! 从电源插座上拔下电源插头。 定期检查排水泵过滤器并确 保其洁净无污。 在以下情况下,清洁排水泵: • 机器不排水。 • 滚筒不转动。 • 由于排水泵阻塞,洗衣机发出异常噪 音。 • 显示屏上显示警告代码 。 警告! • 不得在洗衣机运行时拔下 过滤器。 • 如果洗衣机内是热水,不得 清洗水泵。等到水冷却之 后再清洗 按照如下步骤清洁水泵: 1. 打开水泵盖。 5. 碗中接满水之后,翻转过滤器并清空容 器。 6. 重复步骤 4 和 5,直到水停止流出。 7.
中文 25 2 1 1 2 8. 如有必要,清清理过滤器入口处的绒毛 和物体。 9. 确保泵的叶轮可以旋转。如果不旋转, 请联系授权服务中心。 12. 关闭水泵盖。 2 1 10. 在水龙头下清洗过滤器。 通过紧急排水步骤排水时,必须再次启动 排水系统: a. 向洗涤剂投放盒的主洗盛载格中 倒入 2 升水。 b. 启动程序开始排水。 12.8 清洁进水软管和阀门过滤 器 建议不定期清洁进水管的过滤器和阀门, 以清除长期累积的沉淀物: 1. 从搭接处取下进水管,并清洁过滤器。 1 11. 顺时针旋转,将过滤器重新放入特殊的 滑轨。确保正确紧固了过滤器,以防泄 漏。 2 3 2.
www.aeg.com 12.9 紧急排水 如果本机无法排水,请按照“清洁排水过滤 器”段落中的说明执行相同的步骤。根据需 要清洁排水泵。 通过紧急排水步骤排水时,必须再次启动 排水系统: 1. 向洗涤剂投放盒的主洗盛载格中倒入 2 升水。 2. 启动程序开始排水。 3. 利用牙刷清洁本机背面的阀门过滤器。 12.10 预防霜冻 如果本机安装在温度在 0° C 左右或者更 低的区域,请从进水管排出剩余的水,并 将水泵中的水排空。 1. 从电源插座上拔下电源插头。 2. 关闭水龙头。 3. 将进水软管的两端放在容器中,让水流 出软管。 4. 将排水泵排空。请参阅紧急排水的操 作步骤。 5. 排水泵中的水排空之后,重新装上进水 软管。 警告! 再次使用洗衣机之前,确保温 度高于 0 °C。 制造商对于由低温造成的损 坏不负任何责任。 4. 将软管重新连接到本机背面时,将它向 左或向右旋转(并非垂直位置),具体 取决于您水龙头的位置。 45° 20° 13. 故障排除 警告! 请参阅“安全”一章。 13.
中文 如果本机过载,请从滚筒中 取出一些衣物和/或同时按 住机门并按触 启动/暂停 按钮,直至指示灯 止闪烁(见下图)。 停 27 • - 电源不稳定。请等待电源稳定 后再继续操作。 • - 本机的电子元件之间无通信。关 闭后重新开启。 程序未正常完成,或者本机提前停止。 如果再次显示警报代码,请联系授权服 务中心。 • - 防浸水设备已开启。断开本机 的连接并关闭水龙头。请联系授权服 务中心。 警告! 执行检查之前请停用本机。 13.
www.aeg.
中文 确保滚筒内水位不会过高。 必要时,请使用紧急排水功能 (请参阅《养护和清洁》一章 中的《紧急排水》部分)。 4. 取出衣物,然后关闭机门。 5. 关闭过滤器翻板。 要打开机门,请按照以下步骤操作: 1. 从电源插座上拔下电源插头。 2. 打开过滤器翻板。 3. 向下拉动紧急开锁触发器两次,打开机 门。 14. 技术数据 尺寸 宽/高/深/总深 600 毫米/ 850 毫米/ 630 毫米/ 660 毫米 电气连接 电压 总功率 保险丝 频率 220 - 240 伏 2200 瓦 10 A 50 Hz 防止固体颗粒和潮气侵入的防护等级由防护盖板确保 IPX4 (低压设备无防潮功能时除外) 供水压力 最低 最高 冷水 供水 1) 最大衣物量 棉织物 能效等级 脱水速度 0.5 巴(0.05 兆帕) 8 巴(0.
www.aeg.com 15. 附件 15.1 可访问 www.aeg.com/ shop 或从授权的经销商处获取 只有得到 AEG 批准的适当部 件可确保本机符合安全标准。 如果使用未经批准的部件,任 何索赔都无效。 15.2 固定板套件 若要将本机安装在底座上,请使用固定板 将本机固定。 堆叠套件只能与配件随附的说明书中指定 的机型一起使用。 请仔细阅读与本机和配件一起提供的说 明。 警告! 请勿将滚筒烘干机放在洗衣 机下面。 15.4 带抽屉底座 请仔细阅读此配件随附的说明。 15.3 堆叠套件 抬高本机,让放入和取出衣物变得更加简 单。 抽屉可用于存放衣物,如:毛巾、清洁用 品等。 滚筒烘干机可堆叠在洗衣机顶部,但必须 使用 AEG 制造和批准的正确堆叠套件。 请仔细阅读此配件随附的说明。 检查本机的深度以验证兼容 的堆叠套件。 16.
X X ZH * X X X X X X 中文 31
157017940-A-082018 www.aeg.