L8FEC9412N 用户手册 中文 用户手册 洗衣机
www.aeg.com 内容 1. 安全信息................................................................................................................2 2. 安全说明................................................................................................................4 3. 安装.......................................................................................................................5 4. 产品说明................................................................................................................9 5.
中文 3 担任何责任。请妥善保管操作说明,并置于易于取用的地 方,供将来参考之用。 1.1 儿童及弱势群体安全 • • • • • • • • • 本机可供 8 岁及以上儿童和肢体伤残、感官或精神上有 障碍或缺乏相关经验及知识的人士使用,前提是他们在 使用本机时受到监督或得到安全使用指导,同时了解使 用过程中可能存在的危险。 3 至 8 岁的儿童以及身患大范围复杂残疾的人员应远离 本机,除非始终有人在旁监督。 除非有成人始终在旁监督,否则 3 岁以下儿童应远离本 机。 请勿让儿童玩弄本机。 所有包装物都必须远离儿童,且予以妥善处置。 洗衣剂应远离儿童。 当机门处于打开状态时,勿让儿童和宠物靠近本产品。 如果本机配备儿童安全装置,则应将其打开。 在无人监管的情况下,儿童不能擅自清理和维护本机。 1.
www.aeg.com www.aeg.cn • 请使用湿布清洁本机。只可使用中性清洁剂。请勿使用 磨料制品、磨料清洁垫、溶剂或金属物件。 2. 安全说明 2.1 安装 安装必须符合相关的国家法 规。 • • • • • • • • • • • • • 拆掉所有包装和运输螺栓,包括橡胶套 和塑料垫片。 请将运输螺栓放在安全的地方。如果 日后要移动本机,必须将其重新连接锁 住滚筒以防止内部损坏。 设备非常重,搬运时请注意。请始终佩 戴安全手套和配套的鞋子。 请勿安装或使用已损坏的设备。 按照本机附带的安装说明书操作。 请勿在温度低于 0°C 或露天的地方安 装或使用本机。 安装本机的地面区域必须平稳,耐热且 干净。 确保本机与地面之间有空气流通。 在将本机放置在永久位置后,使用水平 仪帮助检查其是否完全水平。若不是, 可对机脚进行相应调整。 请勿直接将本机安装在地漏上。 请勿将水喷洒到本机上,也不要将它置 于湿度过高的环境。 请勿在无法完全打开机门的地方安装 本机。 请勿在本机下方放置关闭的容器来收 集可能漏出的水。应联系授权服务中 心确认可以使用哪些配件。 2.2 电气连接 • • 2.
中文 • 拆除机门卡扣,以避免儿童或宠物被卡 在滚筒内。 • 根据当地的废电子电机设备 (WEEE) 报废要求处理本机。 3. 安装 警告! 请参阅“安全”一章。 3.1 拆除包装 警告! 在安装本机之前,请移除所有 包装材料和运输螺栓。 警告! 戴上手套。 1. 揭下外膜。如有必要,可使用刀具。 2. 取下纸板顶部和聚苯乙烯包装材料。 5. 小心地将本机背面朝上放下。 6. 将前面的聚苯乙烯包装成份放在本机 下面的地板上。 确保不会对软管造成损害。 7. 撤除底部的聚苯乙烯保护块。 1 3. 揭下内膜。 2 8. 彻底清洁并干燥本机底部。 4.
www.aeg.com www.aeg.cn 警告 勿使用酒精、溶剂或化学品。 9. 确保识别声障的不同大小和位置。请 参考插图: 14. 从软管支架上取下电源线和排水软管。 A B • A(正面)= 本机的正面 • B(背面)= 本机的背面 10. 从静音声障上取下胶条。 11. 将四个声障安装到本机底部。 12. 请参考插图。确保声障都已牢固安装。 x4 A 16. 抽出塑胶垫片。 17. 将用户手册袋中找到的塑料盖放入洞 中。 B 在室温下安装声障。 13. 重新将本机立起来。 可能会有水从排水管中流出。 这是因为工厂里对本机所做 的水流测试。 15.
中文 我们建议您保留包装和运输 螺栓,以便在移动本机时使 用。 3.2 定位和调平 7 3.3 进水软管 1. 将进水软管连接到本机背部。 2. 将它向左或向右放置,具体取决于水龙 头的位置。 1. 将本机安装在平整的硬地面上。 确保地毯不会阻止本机下面 的空气流通。 确保本机不会触碰到墙壁或 其他装置。 2. 拧松或拧紧机脚以调整水平位置。 警告! 调整水平位置时,请勿将本机 置于纸板、木头或位于本机机 脚下的材料上。 45 20 O O 确保进水管不是垂直位置。 3. 如有必要,可松开圆形螺母,将它固定 在正确的位置上。 4. 将进水软管连接到带有 3/4 英寸螺纹 接头的冷水龙头上。 x4 本机必须位于水平且稳定的位置。 正确调整本机位置可防止本 机在使用过程中发生震动、噪 音以及移动的情况。 当本机安装在底座上,或者洗 衣烘干机堆放在洗衣机上,请 使用“配件”一章描述的配件。 请仔细阅读与本机和配件一 起提供的说明。 警告 确保接头处不会发生泄漏。 如果进水软管过短,请勿使用 加长软管。请与服务中心联 系,以更换进水软管。 3.
www.aeg.com www.aeg.cn 3. 流向带有通风孔的立管 - 将排水管直 接插入排水管道中。请参考插图。 A 如果发生这种情况,请关闭水龙头,联系 授权服务中心以更换软管。 3.5 排水 排水管距离地板的高度不低于 60 厘米,且 不超过 100 厘米。 排水软管最多可以加长到 400 厘米。要获得另外的排 水软管和加长软管,请与授权 服务中心联系。 可以用不同的方式连接排水管: 排水软管的末端必须保持通 风,即排水管道的内径 (最小 38 毫米 - 最小 1.5 英 寸)必须大于排水软管的外 径。 4. 如果排水管末端变成这样(参见图片), 您可以将它直接推进立管里。 1. 让排水管摆成 U 型,并将它放在塑料 软管导向装置周围。 2. 在水槽边上 - 将软管导向装置固定到 水龙头或墙壁上。 确保塑料管托在本机排水时 不会移动。 确保排水管末端没有浸入水 中。可能会有脏水回流至本 机。 5. 没有塑料软管导向装置,流向水槽栓 将排水软管插入栓中,并用夹钳将它拧 紧。请参考插图。 确保排水软管形成一个环,以 防止水槽中的颗粒物进入本 机。 6.
中文 9 4. 产品说明 4.1 特殊功能 • 新的洗衣机满足各项现代要求,即用少量 水、能耗和洗涤剂可高效处理衣物,同时 使衣物得到妥善的护理。 • • Oko-Mix 技术 可预先混合不同的阶 段,首先在水中溶解洗涤剂和衣物柔顺 剂,然后将它们分布到衣物中,从而保 护衣物纤维。因此,可深入到每一根纤 维并提供精心护理。 ProSense 技术可检测衣物量,在 30 秒内确定程序持续时间。根据衣物量 和纤维类型定制洗涤程序,不会浪费更 多不必要的时间、能耗和水。 • • 要让衣物焕然一新,蒸汽处理既简单又 快捷。温和的蒸汽程序可去除异味,减 少干燥衣物中的褶皱,从而减少熨烫工 作。 易熨烫 选项在每个程序结束时会有温 和的蒸汽,使衣物舒展并减少衣物褶 皱。熨烫会更加轻松! 去污 选项会预先处理顽固的污渍,优化 去污剂的效果。 使用 软化升级 选项,可将衣物柔顺剂 均匀地喷洒到衣物上,并深入渗透到衣 物纤维中,让衣物变得更加柔顺。 4.
www.aeg.com www.aeg.cn 9 进水软管连接 10 电源电缆 11 运输螺栓 12 软管支架 5. 控制板 5.1 控制板说明 3 2 1 4 5 13 12 11 10 9 8 7 6 1 程序旋钮 2 显示屏 3 节能按触按钮 (节能) 7 额外漂洗按触按钮 (额外漂洗) 4 省时按触按钮 (省时) 10 防污和预洗按触按钮 (去污/预洗) 8 延迟启动按触按钮 (预约) 9 超级蒸汽按触按钮 (易熨烫) 5 跳过阶段按触按钮 (选项) • 跳过洗涤阶段 (单漂洗) • 跳过洗涤和漂洗阶段 (单脱水) • 单排水 (单排水) 6 启动/暂停按触按钮 (启动/暂停) 5.
中文 最大衣物量指示灯。预计衣物量时, “PROSENSE 衣物量检测”一节)。 11 图标会闪烁(请参阅 最大衣物量指示灯。当衣物量超过选定程序声明的最大衣物量时,它会闪 烁。 延迟开始指示灯。 机门已锁指示灯。 数字指示灯可以显示: • 程序持续时间(例如 • 延迟时间(例如 • 程序结束 ( )。 • 警告代码(例如 )。 或 )。 )。 节能指示灯。选择适用于 40 °C 或 60 °C 的棉织物程序时, 会显示。 洗涤阶段指示灯:在预洗和洗涤阶段它会闪烁。 漂洗阶段指示灯:它会在漂洗阶段闪烁。 软化升级 选项激活时,显示 指示灯。 脱水和排水阶段指示灯。在脱水和排水阶段它会闪烁。 MIX OKO MIX 指示灯。 蒸汽阶段指示灯。 防皱处理阶段指示灯。 儿童安全锁指示灯。 省时指示灯。 温度指示灯。设置冷水洗时,显示 脱水速度指示灯。 延迟漂洗指示灯。 静音指示灯。 预洗指示灯。 污渍指示灯。 指示灯。 指示灯
www.aeg.com www.aeg.cn 额外漂洗指示灯。 6. 旋钮和按钮 6.1 开/关 按触此按钮并停留几秒钟,可激活或停用 本机。打开或关闭本机时会有两种不同的 声音。 • 有时候,您可能需要再次启动本机,待机 功能可自动停用本机以降低能耗。 有关更多信息,请参阅“日常使用”一章中 的“待机”一节。 6.2 简介 并非所有洗涤程序都可选择 某些选项/功能。在“程序表” 一节检查选项/功能与洗涤程 序之间的兼容性。一个选项/ 功能可能与另一个相互排斥, 如果是这种情况,本机不允许 您同时设置不兼容的选项/功 能。 确保触摸屏和按触按钮始终 清洁干燥。 6.3 温度 选择一个洗涤程序时,本机会自动提议一 个默认温度。 显示屏上将显示指示灯 。 机门保持锁定状态。滚筒定时旋转,以 减少起皱。您必须打开机门将水排出。 按触 启动/暂停 按钮:本机仅执行排水 阶段。 本机大约会在 18 小时之后自 动将水排空。 6.
中文 6.6 额外漂洗 6.9 省时 根据选定的洗涤程序,利用此选项最多可 添加 3 次漂洗。 使用此选项可缩短程序持续时间。 适用于对洗衣剂过敏的人群以及水质较软 的地区。 指示灯显示选择的漂洗次数。 此选项会延长程序持续时间。 • • 。 洗涤程序,显示屏会显示 此时按触 额外漂洗 按钮,可 以只添加一次漂洗。 6.
www.aeg.com www.aeg.cn 7. 程序 7.
中文 程序 15 程序说明 请勿使用衣物柔顺剂,确保洗涤剂投放盒中没 有柔顺剂残留物。 户外 户外衣物,技术织物、运动衣物、防水透气夹克、带有可拆卸 抓绒或保温内胆的紧身夹克。建议的衣物量为 2.
www.aeg.com www.aeg.cn 程序 默认温度 温度范围 最大脱水转速 脱水速度范围 最大衣物量 20 分鈡-3 公斤 30 °C 40 °C - 30 °C 1200 转/分 3 公斤 1200 转/分 - 400 转/分 户外 30 °C 40 °C - 冷洗 1200 转/分 2.
■ ■ 17 羽绒被 户外 20 分鈡-3 公斤 抗过敏 ■ 经济洗 ■ 蒸汽 精细 ■ 羊毛/丝绸 化纤 软化升级 棉织物 中文 ■ 1) 温度低于 40 °C 时,不可使用此选项。 2) 该选项在温度低于 30 °C 时不可用。 3) 如果设定了更短的持续时间,建议您减少衣物量。本机可以满载放入衣物,但这样会降低洗涤效果。 7.2 Woolmark Apparel Care - 绿色 本机的毛织品洗涤程序已通过 The Woolmark Company(国际羊毛局)测试和认可,适用于 洗涤标有“手洗”字样的羊毛针织衣物,只要按 照由该洗衣机制造商发布的说明洗涤衣物即 可。按照衣物护理标签进行烘干并遵循其他洗 衣说明。M1361 羊毛标记符号是在许多国家/地区的认证标记。 8. 初次使用前 在安装过程中或者初次使用 前,可能会发现本机内有一些 水。这是工厂执行全面的功 能测试时留下的水,执行功能 测试是为了确保本机交付到 客户时可正常运行,且没有后 顾之忧。 1. 确保取下本机上的所有运输螺栓。 2. 确保电源可用并打开水龙头。 3.
www.aeg.cn www.aeg.com 9.2 声音信号 本机有不同的声音信号,发生以下情况时 会响起: • • • • • • 启动本机(特殊的短音)。 停用本机(特殊的短音)。 按触按钮(咔哒声)。 做出了错误的选择(3 个短音)。 程序完成(大约 2 分钟的音串)。 本机发生故障(一串短音,大约持续 5 分钟)。 要在程序完成时停用/启用声音信号,请同 时按触 额外漂洗 和 预约 按钮并保持大约 6 秒钟。 禁用声响信号功能后,机器发 生故障时仍会继续发出声响 信号。 • 要启用/停用此选项,请同时按触 额外 漂洗 按钮和 选项 按钮,直到相关指示 灯亮起/熄灭。 此选项会添加两次漂洗,且显示屏显示 。 9.4 软化升级 设置 软化升级 选项,以优化衣物柔顺剂分 配并提高衣物柔软度。 建议在使用衣物柔顺剂时设置此选项。 此选项会略为延长程序持续 时间。 要启用/停用此选项,请同时按触 温度 按钮 和 脱水 按钮,直到指示灯 指示灯 亮起/熄灭。 上方的 9.3 固定额外漂洗 使用此选项,您可在设置程序时永久使用 额外漂洗(若可选择)。 10.
中文 10.3 放入洗涤剂和添加剂 3. 要使用粉状洗涤剂,请调高悬板。 4. 要使用液体洗涤剂,请调低悬板。 用于预洗阶段和浸泡程序的盛载 格。 供洗涤阶段使用的盛载格。 液体添加剂(衣物柔顺剂、衣浆) 的盛载格。 液体添加剂的最大数量水平。 去污剂盛载格。 用于投放粉状或液体洗涤剂的悬 板。 始终遵循洗涤剂产品包装上 的说明,但我们建议您不要 超过指示的最大级别 ( )。但是此数量可保证 获得最好的洗涤效果。 悬板位置位于下方时: • 请勿使用凝胶状或粘 稠的液体洗涤剂。 • 请勿投放超出悬板所 示限额的液体洗涤剂。 • 切勿设定“预洗”阶段。 • 切勿设定“延迟开始”功 能。 5. 量取适量的洗涤剂和衣物柔顺剂。 6. 小心地关闭洗涤剂投放盒。 洗涤程序结束后,如有必 要,可从洗涤剂投放盒中清 理洗涤剂残留物。 10.4 检查悬板的位置 1. 将洗涤剂投放盒完全拉开。 2.
www.aeg.com www.aeg.cn 10.5 设定程序 1. 旋转程序旋钮,以选择所需的洗涤程 序。相关程序指示灯亮起。 启动/暂停 按钮指示灯闪烁。 显示屏显示程序声明的最大衣物量、默认 温度、最大脱水速度、洗涤阶段指示灯(若 可用)以及指示的程序持续时间。 2. 要更改温度和/或脱水转速,请按触相 关按钮。 3. 若需要,可按触相关按钮设置一个或多 个选项。相关指示灯会在显示屏中亮 起,给定的信息也会发生相应变化。 如果不能作出某一选择,不会 有指示灯亮起,也不会发出声 音信号。 10.6 启动程序 按触 启动/暂停 按钮以启动程序。 相关指示灯停止闪烁,并保持亮起。 显示屏中,表示操作阶段的指示灯开始闪 烁,最大衣物量指示灯熄灭。 程序开始时,机门被锁定。显示屏上将显 示标志 。 本机注水之后,排水泵可立即 开始工作。 10.7 启动带延迟开始功能的程 序 1. 反复按触 预约 按钮,直到显示屏显示 所需的延迟时间。指示灯 亮起。 2.
中文 例如,漂洗阶段正在运行: . 在洗涤阶段,在将衣物放入滚筒之前,本 机会混合洗涤剂,处理衣物去除污渍和/或 在水中加入衣物柔顺剂;指示灯 会根据 不同的程序阶段出现或不出现在显示屏上 (或者是箭头闪烁)。 MIX 如果您选择 易熨烫,蒸汽阶段指示灯会亮 起。 蒸汽阶段正在运行: 防皱处理阶段正在运行: 21 3. 关闭机门,按触按钮 启动/暂停。 程序或延迟开始将继续。 4. 程序完成后,或者设置 脱水/排水 程 序,然后按触 启动/暂停 按钮,可打开 机门。 10.13 程序结束 程序结束后,本机自动停止。声响信号响 起(如果已启用)。 显示屏上所有洗涤阶段指示灯都变得稳 定,且时间区域显示 。 . 启动/暂停 按钮的指示灯熄灭。 . 10.10 中断程序并更改选项 在程序运行时,您只能更改某些选项: 1. 按触按钮 启动/暂停。 相关指示灯将闪烁。 2. 更改选项。显示屏中给定的信息会发 生相应的变化。 3. 再次按触按钮 启动/暂停。 洗涤程序将继续运行。 10.11 取消正在运行的程序 1. 按触 开/关 按钮,取消程序并停用本 机。 2.
www.aeg.com www.aeg.cn 在任何情况下,大约在 18 小 时之后,本机都会自动将水排 空。 • 10.15 待机选项 待机功能会在以下情况下自动停用本机以 降低能耗: • 按下 开/关 按钮可再次启动本机。 在洗涤程序结束 5 分钟后 按触 开/关 按钮以再次启动本机。 显示屏将显示最后一次设定程序的结 束时间。 旋转程序旋钮以设定新程序。 如果设定了结束时有水留在 滚筒中的程序或选项,待机功 能不会停用本机以提醒您排 水。 按触 启动/暂停 按钮之前,请在 5 分钟 内不要使用本机。 11. 建议和提示 警告! 请参阅“安全”一章。 11.
中文 23 使用适量的水质软化剂。请遵守产品包装 上的使用说明。 12. 养护和清洁 警告! 请参阅“安全”一章。 12.4 机门密封圈 12.1 外部清洁 请仅使用温和的肥皂和温水清洁本机。清 洁后将所有表面完全擦干。 警告 勿使用酒精、溶剂或化学品。 警告 请勿使用氯基洗涤剂清洁金 属表面。 12.2 除垢 如果您所在地区的水质硬度 较高或为中等,建议使用针对 洗衣机的除垢产品。 定期检查滚筒内是否有水垢。 普通的洗涤剂中已含有软水剂,但我们仍 建议在排空滚筒之后运行该程序并偶尔使 用除垢产品。 请务必始终遵守产品包装上 的使用说明。 12.3 保养洗涤 经常延长使用低温程序可减少滚筒和洗衣 筒的洗涤剂残留物,绒毛残留物、细菌繁 殖。这些可产生难闻的气味和霉菌。 要清除这些残留物并对本机内部进行卫生 消毒,定期运行维护清洗(至少每月一次)。 定期检查密封圈,并清除其内部的所有异 物。 12.5 清洁滚筒 定期检查滚筒,以防止生锈。 要进行彻底的清洁: 1. 使用专用的不锈钢清洁剂来清洁滚筒。 请务必始终遵守产品包装上 的使用说明。 2.
www.aeg.com www.aeg.cn • 由于排水泵阻塞,洗衣机发出异常噪 音。 • 显示屏上显示警告代码 。 警告! • 不得在洗衣机运行时拔下 过滤器。 • 如果洗衣机内是热水,不得 清洗水泵。等到水冷却之 后再清洗 按照如下步骤清洁水泵: 3. 确保清除了凹处上部和下部的所有清 洁剂残留物。使用小刷子清洁凹处。 1. 打开水泵盖。 2 1 4. 将清洁剂抽屉插入导轨,并将其关闭。 滚筒中不放入任何衣物,运行漂洗程 序。 2. 将一个适当的碗置于排水泵接口下方, 以收集从泵中流出的水。 3. 向下打开斜槽。卸下泵过滤器时身边 应准备一块布随时抹干流出来的水。 12.7 清洁排水泵。 4.
中文 25 11. 顺时针旋转,将过滤器重新放入特殊的 滑轨。确保正确紧固了过滤器,以防泄 漏。 5. 碗中接满水之后,翻转过滤器并清空容 器。 6. 重复步骤 4 和 5,直到水停止流出。 7. 逆时针旋转过滤器可将其卸下。 2 1 1 2 12. 关闭水泵盖。 8. 如有必要,清清理过滤器入口处的绒毛 和物体。 9. 确保泵的叶轮可以旋转。如果不旋转, 请联系授权服务中心。 2 1 通过紧急排水步骤排水时,必须再次启动 排水系统: a. 向洗涤剂投放盒的主洗盛载格中 倒入 2 升水。 b. 启动程序开始排水。 10. 在水龙头下清洗过滤器。 12.8 清洁进水软管和阀门过滤 器 建议不定期清洁进水管的过滤器和阀门, 以清除长期累积的沉淀物: 1.
www.aeg.com www.aeg.cn 12.9 紧急排水 如果本机无法排水,请按照“清洁排水过滤 器”段落中的说明执行相同的步骤。根据需 要清洁排水泵。 1 通过紧急排水步骤排水时,必须再次启动 排水系统: 2 1. 向洗涤剂投放盒的主洗盛载格中倒入 2 升水。 2. 启动程序开始排水。 3 2. 松开圆形螺母,从本机中取出进水管。 12.10 预防霜冻 如果本机安装在温度在 0° C 左右或者更 低的区域,请从进水管排出剩余的水,并 将水泵中的水排空。 1. 从电源插座上拔下电源插头。 2. 关闭水龙头。 3. 将进水软管的两端放在容器中,让水流 出软管。 4. 将排水泵排空。请参阅紧急排水的操 作步骤。 5. 排水泵中的水排空之后,重新装上进水 软管。 3. 利用牙刷清洁本机背面的阀门过滤器。 4.
中文 27 13. 故障排除 警告! 请参阅“安全”一章。 13.1 简介 洗碗机无法启动或在运行过程中停止。 首先,尝试找到问题的解决方法(参考下 表)。如果问题仍然存在,请联系授权服务 中心。 如果出现重要问题,声音信号响起,显示 屏显示警报代码,且 启动/暂停 按钮可能持 续闪烁: • - 机器不能正常注水。 按触 启动/暂停 按钮启动本机。5 秒钟 后机门打开。 • • • - 电源不稳定。请等待电源稳定 后再继续操作。 • - 本机的电子元件之间无通信。关 闭后重新开启。 程序未正常完成,或者本机提前停止。 如果再次显示警报代码,请联系授权服 务中心。 • - 防浸水设备已开启。断开本机 的连接并关闭水龙头。请联系授权服 务中心。 - 本机不排水。 - 机门打开或未正确关闭。请检 查机门! 如果本机过载,请从滚筒中 取出一些衣物和/或同时按 住机门并按触 启动/暂停 按钮,直至指示灯 止闪烁(见下图)。 停 警告! 执行检查之前请停用本机。 13.
www.aeg.com www.aeg.
中文 13.3 应急机门开启 29 要打开机门,请按照以下步骤操作: 在出现电源故障或功能故障的情况下,机 门仍会保持锁定状态。当供电恢复时,洗 涤程序会继续执行。如果出现故障时机门 仍保持锁定状态,则可使用应急解锁功能 将其打开。 1. 从电源插座上拔下电源插头。 2. 打开过滤器翻板。 3. 向下拉动紧急开锁触发器两次,打开机 门。 打开机门之前: 警告 小心烫伤!确保水温和衣物 温度不会太高。必要时请稍 等片刻,直到它们冷却。 警告 受伤危险。确保滚筒未旋转。 必要时请稍等片刻,直到滚筒 停止旋转。 确保滚筒内水位不会过高。 必要时,请使用紧急排水功能 (请参阅《养护和清洁》一章 中的《紧急排水》部分)。 4. 取出衣物,然后关闭机门。 5. 关闭过滤器翻板。 14.
www.aeg.com www.aeg.cn 15. 附件 www.aeg.cn 15.1 可访问 www.aeg.com/ shop 或从授权的经销商处获取 只有得到 AEG 批准的适当部 件可确保本机符合安全标准。 如果使用未经批准的部件,任 何索赔都无效。 15.2 固定板套件 若要将本机安装在底座上,请使用固定板 将本机固定。 堆叠套件只能与配件随附的说明书中指定 的机型一起使用。 请仔细阅读与本机和配件一起提供的说 明。 警告! 请勿将滚筒烘干机放在洗衣 机下面。 15.4 带抽屉底座 请仔细阅读此配件随附的说明。 15.3 堆叠套件 抬高本机,让放入和取出衣物变得更加简 单。 抽屉可用于存放衣物,如:毛巾、清洁用 品等。 滚筒烘干机可堆叠在洗衣机顶部,但必须 使用 AEG 制造和批准的正确堆叠套件。 请仔细阅读此配件随附的说明。 检查本机的深度以验证兼容 的堆叠套件。 16.
X X ZH * X X X X X X 中文 31
157017941-A-192018 www.aeg.