L8FEC96S USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE.................................................................................................3 2. SICHERHEITSANWEISUNGEN...................................................................................... 4 3. MONTAGE.......................................................................................................................6 4. GERÄTEBESCHREIBUNG..........................................................................................
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie die mitgelieferte Gebrauchsanleitung sorgfältig vor Montage und Inbetriebnahme des Geräts. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com 1.2 Allgemeine Sicherheit • • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Überschreiten Sie nicht die maximale Beladungsmenge von 9 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • • • • • • • • • verriegeln und dadurch interne Schäden zu vermeiden. Seien Sie beim Bewegen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk. Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. Halten Sie sich an die mitgelieferte Montageanleitung. Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist.
www.aeg.com • Berühren Sie während des Betriebs nicht die Glastür. Das Glas kann sehr heiß werden. 2.5 Service • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. 2.6 Entsorgung • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung. • Schneiden Sie das Netzkabel in der Nähe des Geräts ab, und entsorgen Sie es.
DEUTSCH 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 1 2 8. Reinigen Sie die Unterseite des Geräts und trocknen Sie sie ab. 7 VORSICHT! Verwenden Sie keinen Alkohol, keine Lösungsmittel und keine Chemikalien. 9. Sortieren Sie die verschiedenen Teile des Schallschutzes nach Größe und Position.
www.aeg.com x4 A B Bringen Sie die Schallschutzteile bei Raumtemperatur an. 13. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 14. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. 16. Ziehen Sie die KunststoffAbstandshalter heraus. 17. Setzen Sie die Kunststoffkappen, die sich im Beutel mit der Bedienungsanleitung befinden, in die Löcher ein. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren. 3.
DEUTSCH 9 WARNUNG! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 45 20 x4 Das Gerät muss einen waagerechten und festen Stand haben. Durch eine korrekte waagrechte Ausrichtung des Geräts werden Vibrationen, Geräusche und ein Wandern des Geräts während des Betriebs vermieden. O O Vergewissern Sie sich, dass sich der Zulaufschlauch nicht in der vertikalen Position befindet. 3. Lösen Sie ggf.
www.aeg.com durch natürliche Alterung auftreten können. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an. A Tritt dieser Fall ein, drehen Sie den Wasserhahn zu und wenden Sie sich an den autorisierten Kundendienst, um den Schlauch zu erneuern. 3.5 Ablassen des Wassers Der Ablaufschlauch muss in einer Höhe nicht unter 60 cm und nicht über 100 cm angebracht werden.
DEUTSCH 11 Stellen Sie sicher, dass der Ablaufschlauch einen Bogen beschreibt, damit keine Partikel aus dem Siphon in das Gerät gelangen können. 6. Stecken Sie den Schlauch direkt in ein Abflussrohr in der Zimmerwand und befestigen Sie ihn mit einer Schlauchschelle. 5. Ohne Kunststoffschlauchführung: Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Orientieren Sie sich an der Abbildung. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
www.aeg.com 4.2 Geräteübersicht 1 2 9 8 3 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Arbeitsplatte Waschmittelschublade Bedienfeld Türgriff Typenschild Filter der Ablaufpumpe Füße für die Ausrichtung des Geräts 8 9 10 11 12 Ablaufschlauch Anschluss des Zulaufschlauchs Netzkabel Transportschrauben Schlauchhalter 5. BEDIENFELD 5.
DEUTSCH 1 Programmwahlschalter 2 Display 3 Sensortaste Eco (Eco) 4 Sensortaste Zeit Sparen (Tijd Besparen - Gain de temps) 5 Sensortaste Überspringen (Extra) • Waschphase überspringen (Nur Spülen) • Wasch- und Spülphase überspringen (Nur Schleudern) • Nur Abpumpen (Nur Abpumpen) 13 8 Sensortaste Zeitvorwahl (Startuitstel Départ différé) 9 Sensortaste Plus Dampf (Plus Steam) 10 Sensortaste Flecken und Vorwäsche (Vlekken/Voorwas - Taches/ Prélavage) 11 Sensortaste Drehzahlreduzierung (TPM) 12 Taste Ein/Aus
www.aeg.com Die Digitalanzeige zeigt Folgendes an: ). • Programmdauer (z. B. • Zeitvorwahl (z. B. oder ). • Programmende ( ). • Fehlercode (z. B. ). Energiesparanzeige. Die Anzeige erscheint, wenn ein Baumwollprogramm mit 40 °C oder 60 °C gewählt wird. Hauptwaschgangsanzeige: Blinkt während der Vorwasch- und Hauptwaschphase. Spülphasenanzeige: Blinkt während der Spülphase. Die Anzeige erscheint, wenn die Option Soft Plus eingeschaltet ist. Schleuder- und Abpumpphasenanzeige.
DEUTSCH 15 6. DREHSCHALTER UND TASTEN 6.1 AAN /UIT - MARCHE/ ARRÊT Halten Sie diese Taste einige Sekunden lang gedrückt, um das Gerät ein- oder auszuschalten. Beim Ein- und Ausschalten ertönen zwei verschiedene Melodien. Da die Standby-Funktion das Gerät automatisch ausschaltet, um in einigen Fällen den Stromverbrauch zu verringern, müssen Sie es möglicherweise erneut einschalten. Siehe Abschnitt Standby im Kapitel „Täglicher Gebrauch“. 6.
www.aeg.com Berühren Sie die Taste Start/Pauze Départ Pause: Das Gerät pumpt nur das Wasser ab. Das Gerät pumpt das Wasser nach etwa 18 Stunden automatisch ab. 6.5 Vlekken/Voorwas - Taches/ Prélavage Drücken Sie diese Taste mehrmals, um eine der beiden oder beide Optionen einzuschalten. Die entsprechende Anzeige leuchtet im Display. • Vlekken - Taches Wählen Sie diese Option zur Vorbehandlung stark verschmutzter oder stark fleckiger Wäsche mit einem Fleckentferner.
DEUTSCH 6.8 Eco Wählen Sie diese Option für leicht oder normal verschmutzte Wäsche, die bei 30 °C oder höheren Temperaturen gewaschen werden soll. Das Gerät verringert die Temperatur und verlängert den Waschgang, um wirtschaftlich zu waschen und Energie zu sparen. Auf dem Display erscheint die Anzeige . Wenn Sie ein Baumwollprogramm mit 40 °C oder 60 °C wählen, erscheint im Display die Anzeige .
www.aeg.com 7. PROGRAMME 7.1 Programmübersicht Waschprogramme Programm Programmbeschreibung Waschprogramme Katoen - Blanc/Couleurs (Baumwolle) Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte. Das Programm Katoen - Blanc/ Couleurs bei 60 °C und das Programm Katoen - Blanc/ Couleurs bei 40 °C mit der Option sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“.
DEUTSCH Programm 19 Programmbeschreibung Dampfprogramm für Baumwolle und pflegeleichte Wä- Stoom - Vapeur (Dampf) sche.Dampf kann verwendet werden für getrocknete2), gewaschene oder einmal getragene Wäschestücke. Dieses Programm reduziert Falten und Gerüche.3) und lockert die Fasern auf. Nehmen Sie nach Ablauf des Programms die Wäsche schnell aus der Trommel. Nach einem Dampfprogramm lässt sich die Wäsche mühelos bügeln. Verwenden Sie kein Waschmittel.
www.aeg.com Programm Programmbeschreibung Outdoor (Outdoor) Synthetische Sportbekleidung. Dieses Programm eignet sich zur schonenden Wäsche moderner Sportbekleidung, wie Trainings-, Radfahr- oder Joggingkleidung und ähnlicher OutdoorBekleidung. Die empfohlene Beladung beträgt 2.5 kg. Verwenden Sie, um bessere Ergebnisse zu erzielen, keinen Weichspüler und stellen Sie sicher, dass sich keine Weichspülerrückstände in der Waschmittelschublade befinden. Wasserdichtes, atmungsaktives Gewebe.
DEUTSCH Programmtemperatur, maximale Schleuderdrehzahl und maximale Beladung Programm Standardtemperatur Maximale Schleuder- Maximale BelaTemperaturbereich drehzahl dung Schleuderdrehzahlbereich 40 °C 95 °C – kalt 1600 U/min 1600 U/min – 400 U/min 9 kg 40 °C 60 °C – kalt 1200 U/min 1200 U/min – 400 U/min 4 kg 40 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 4 kg 40 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 2 kg - - 1.
www.aeg.com Anti-Allergie - Anti-Allergies 20 min.
■ 23 Machine Clean Outdoor 20 min. - 3 kg Anti-Allergie - Anti-Allergies ■ ÖKOPower ■ Stoom - Vapeur Fijne Was - Délicats ■ Wol/Zijde - Laine/Soie Synthetica - Synthétiques Soft Plus Katoen - Blanc/Couleurs DEUTSCH ■ 1) Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C. 2) Diese Option ist nicht verfügbar bei einer Temperatur unter 30 °C. 3) Wenn Sie die kürzeste Programmdauer einstellen, empfehlen wir Ihnen, die Wäschemenge zu verringern.
www.aeg.com 9. EINSTELLUNGEN 9.1 Kindersicherung Diese Option verhindert, dass Kinder mit dem Bedienfeld spielen. - Rinçage+ und Startuitstel - Départ differé gleichzeitig etwa 6 Sekunden lang. Sind die akustischen Signale ausgeschaltet, ertönen sie nur noch dann, wenn eine Störung vorliegt. • Berühren Sie zum Ein-/Ausschalten dieser Option die Tasten Vlekken/ Voorwas - Taches/Prélavage und Spoelen+ - Rinçage+ gleichzeitig, bis die Anzeige im Displayleuchtet/ erlischt.
DEUTSCH lang gedrückt, um das Gerät einzuschalten. Es ertönt eine kurze Melodie (falls eingeschaltet). Der Programmwahlschalter wird automatisch auf Baumwolle gesetzt. 25 10.3 Einfüllen von Wasch- und Pflegemitteln Das Display zeigt die maximale Beladung, die Standardtemperatur, die maximale Schleuderdrehzahl, die Anzeigen der Phasen, aus denen das Programm besteht, und die Programmdauer an. 10.2 Einfüllen der Wäsche 1. Öffnen Sie die Tür des Geräts. 2.
www.aeg.com 1 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. • Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. • Stellen Sie nicht den Vorwaschgang ein. • Stellen Sie nicht die Zeitvorwahl ein. 5. Messen Sie Waschmittel und Weichspüler ab. 6. Schließen Sie die Waschmittelschublade vorsichtig. 4.
DEUTSCH 3. Schalten Sie bei Bedarf eine oder mehrere Optionen durch Berühren der entsprechenden Tasten ein. Die zugehörigen Anzeigen leuchten im Display und die angezeigten Informationen ändern sich entsprechend. Wenn die Auswahl nicht möglich ist, leuchtet keine Anzeige und es ertönt ein akustisches Signal. 10.6 Starten eines Programms Berühren Sie die Taste Start/Pauze Départ Pause, um das Programm zu starten. Die zugehörige Kontrolllampe hört auf zu blinken und leuchtet konstant.
www.aeg.com In diesem Fall können Sie innerhalb von 30 Sekunden das Gerät anhalten und die überzähligen Wäschestücke entnehmen. Berühren Sie nach Entnahme der überzähligen Wäschestücke die Taste Start/Pauze - Départ Pause, um das Programm wieder zu starten. Die ProSense Phase kann bis zu drei Mal wiederholt werden (siehe Punkt 1). Wichtig! Wird die Wäschemenge nicht verringert, startet das Waschprogramm trotz der Überladung. In diesem Fall können keine optimalen Waschergebnisse garantiert werden.
DEUTSCH Wurde die ProSense-Phase bereits beendet und läuft Wasser in das Gerät ein, startet das neue Programm ohne die ProSense-Phase zu wiederholen. Um Verschwendung zu vermeiden, werden Wasser und Waschmittel nicht abgepumpt. Das Display zeigt die maximale Programmdauer an, die etwa 20 Minuten nach dem Start des neuen Programms aktualisiert wird. 10.
www.aeg.com • Wenn Sie gewählt haben, pumpt das Gerät nur das Wasser ab. Die Optionsanzeige oder erlischt, blinkt und dann während die Anzeige erlischt. 3. Wenn das Programm beendet ist und die Türverriegelungsanzeige erlischt, können Sie die Tür öffnen. 4. Halten Sie die Taste AAN /UIT MARCHE/ARRÊT einige Sekunden lang gedrückt, um das Gerät auszuschalten. In jedem Fall pumpt das Gerät das Wasser nach etwa 18 Stunden automatisch ab. 10.
DEUTSCH a. Unterbrechen Sie das Programm und öffnen Sie die Tür (siehe „Öffnen der Tür nach erfolgtem Programmstart oder während der Zeitvorwahl“). b. Verteilen Sie die Wäsche mit der Hand neu, so dass die Wäschestücke gleichmäßig verteilt sind. c. Drücken Sie die Taste Start/ Pauze - Départ Pause. Die Schleuderphase wird fortgesetzt. 11.2 Hartnäckige Flecken Für manche Flecken sind Wasser und Waschmittel nicht ausreichend.
www.aeg.com VORSICHT! Verwenden Sie keinen Alkohol, keine Lösungsmittel und keine Chemikalien. 12.4 Türdichtung 12.2 Entkalkung Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Entkalkers für Waschmaschinen. Prüfen Sie die Trommel regelmäßig auf Kalkablagerungen. Herkömmliche Waschmittel enthalten Wasserenthärtungsmittel, wir empfehlen dennoch gelegentlich ein Programm mit leerer Trommel und einem Entkalker durchzuführen.
DEUTSCH 33 1 2 2. Entfernen Sie das Oberteil des Pflegemittelfachs, um die Reinigung zu vereinfachen, und spülen Sie es mit fließendem warmen Wasser aus, um das angesammelte Waschmittel zu beseitigen. Setzen Sie nach der Reinigung das Oberteil wieder ein. 12.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. 3.
www.aeg.com 2 1 2 1 2. Stellen Sie einen geeigneten Behälter unter die Öffnung der Ablaufpumpe, um das abfließende Wasser aufzufangen. 3. Drücken Sie die beiden Hebel, und ziehen Sie den Ablaufkanal nach vorne, um ihn zu öffnen. 1 7. Schließen Sie den Ablaufkanal und drehen Sie das Sieb gegen den Uhrzeigersinn, um es zu entfernen. 2 1 1 2 4. Lassen Sie das Wasser ablaufen. 5. Wenn der Behälter voll ist, schließen Sie den Ablaufkanal und leeren Sie den Behälter. 6.
DEUTSCH 35 12.8 Reinigen des Siebs des Zulaufschlauchs und Ventils Es wird empfohlen, das Sieb des Zulaufschlauchs und das des Ventils gelegentlich zu reinigen, um Ablagerungen zu entfernen, die sich mit der Zeit ansammeln. 1. Schrauben Sie den Zulaufschlauch vom Wasserhahn ab und reinigen Sie das Sieb. 11. Setzen Sie das Sieb wieder in die dafür vorgesehenen Führungen ein und drehen Sie es im Uhrzeigersinn. Achten Sie darauf, dass Sie das Sieb richtig fest anziehen, um Wasserlecks zu vermeiden.
www.aeg.com 4. Wenn Sie den Schlauch wieder an der Geräterückseite anbringen, drehen Sie ihn je nach Position des Wasserhahns nach rechts oder links (nicht in die vertikale Position). 45° 20° 12.9 Notentleerung Kann das Gerät das Wasser nicht abpumpen, führen Sie den unter „Reinigen des Ablauffilters“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. 12.
DEUTSCH Ist das Gerät überladen, nehmen Sie einige Wäschestücke aus der Trommel und/oder drücken Sie die Tür zu und berühren Sie gleichzeitig die Taste Start/Pauze - Départ Pause, bis die Anzeige aufhört zu blinken (siehe Abbildung unten). 37 • - Die Stromzufuhr ist nicht konstant. Warten Sie, bis die Netzspannung wieder konstant ist. • - Keine Kommunikation zwischen den elektronischen Bauteilen des Geräts. Schalten Sie das Gerät aus und wieder ein. • – Das Aqua-Control-System ist eingeschaltet.
www.aeg.com Störung Mögliche Abhilfe Überzeugen Sie sich, dass das Sieb des Zulaufschlauchs und das Sieb des Ventils nicht verstopft sind. Siehe „Reinigung und Pflege“. Vergewissern Sie sich, dass der Zulaufschlauch nicht geknickt oder zu stark gekrümmt ist. Vergewissern Sie sich, dass der Wasserzulaufschlauch ordnungsgemäß angeschlossen ist. Das Wasser, das in das Vergewissern Sie sich, dass sich der Ablaufschlauch in der richGerät einläuft, wird sofort tigen Höhe befindet.
DEUTSCH Störung 39 Mögliche Abhilfe Vergewissern Sie sich, dass das Waschprogramm beendet ist. Stellen Sie das Abpump- oder Schleuderprogramm ein, wenn sich noch Wasser in der Trommel befindet. Stellen Sie sicher, dass das Gerät mit Spannung versorgt wird. Das Problem kann durch eine Gerätestörung verursacht worden sein. Wenden Sie sich an einen autorisierten Kundendienst. Wenn Sie die Tür öffnen müssen, lesen Sie sorgfältig „Öffnen der Tür im Notfall“.
www.aeg.com Schalten Sie das Gerät nach der Überprüfung wieder ein. Das Programm wird an der Stelle fortgesetzt, an der es unterbrochen wurde. Tritt das Problem erneut auf, wenden Sie sich an den autorisierten Kundendienst. Wenn im Display andere Alarmcodes angezeigt werden. Schalten Sie das Gerät aus und wieder ein. Tritt das Problem weiterhin auf, wenden Sie sich an den autorisierten Kundendienst. 13.
DEUTSCH Während des Waschprogramms können durch die ProSense-Technologie die Programmdauer und die Verbrauchswerte variieren. Siehe „ProSense-Beladungserkennung“ im Kapitel „Täglicher Gebrauch“. Programme Beladung (kg) EnergieWasserUngeRestverbrauch verbrauch fähre Pro- feuchte (kWh) (Liter) grammda- (%)1) uer (in Minuten) Katoen - Blanc/Couleurs 60 °C 9 1.65 90 220 44 Katoen - Blanc/Couleurs 40 °C 9 1.2 90 210 44 Synthetica - Synthétiques 40 °C 4 0.
www.aeg.com Elektrischer Anschluss Spannung Gesamtleistung Sicherung Frequenz 230 V 2200 W 10 A 50 Hz Die Schutzverkleidung gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt.
DEUTSCH 43 Lesen Sie die dem Gerät und dem Zubehör beiliegenden Anleitungen sorgfältig durch. Messen Sie die Tiefe der Geräte, um sich zu vergewissern, dass der Bausatz mit Ihren Geräten kompatibel ist. Der Bausatz Wasch-Trocken-Säule kann nur mit den Geräten verwendet werden, die in der mit dem Zubehör mitgelieferten Broschüre aufgeführt sind. WARNUNG! Stellen Sie den Wäschetrockner nicht unter die Waschmaschine. 17. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol .
157002680-A-192016 www.aeg.