L8FER962C USER MANUAL FR Notice d'utilisation Lave-linge
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ.................................................................................3 2. CONSIGNES DE SÉCURITÉ........................................................................................4 3. INSTALLATION............................................................................................................6 4. DESCRIPTION DE L'APPAREIL.................................................................................10 5.
FRANÇAIS 1. 3 INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • La pression de l'eau en service au niveau du point d'entrée en provenance de l'arrivée d'eau doit être comprise entre 0,5 bar (0,05 MPa) et 8 bar (0,8 MPa). Les orifices d'aération situés à la base (si présents) ne doivent pas être obstrués par de la moquette, un tapis, ou tout type de revêtement de sol. L'appareil doit être raccordé à l'arrivée d'eau à l'aide des tuyaux neufs fournis, ou d'autres tuyaux neufs fournis par le service après-vente agréé.
FRANÇAIS service après-vente agréé pour connaître les accessoires disponibles. 2.2 Branchement électrique • L'appareil doit être relié à la terre. • Utilisez toujours une prise de courant de sécurité correctement installée. • Vérifiez que les paramètres figurant sur la plaque signalétique correspondent aux données électriques de votre réseau. • N'utilisez pas d'adaptateurs multiprises ni de rallonges. • Veillez à ne pas endommager la fiche secteur ni le câble d'alimentation.
www.aeg.com d'équipements électriques et électroniques (DEEE). 3. INSTALLATION AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 3.1 Déballage AVERTISSEMENT! Retirez l'intégralité de l'emballage et les boulons de transport avant d'installer l'appareil. AVERTISSEMENT! Servez-vous de gants. 4. Ouvrez le hublot et retirez la cale en polystyrène du joint du hublot, ainsi que tous les articles présents dans le tambour. 1. Retirez le film externe. Si nécessaire, utilisez un cutter. 2.
FRANÇAIS x4 1 7 A 2 8. Nettoyez soigneusement et séchez le bas de l'appareil. ATTENTION! N'utilisez pas d'alcool, de solvants ni de produits chimiques. 9. Veillez à identifier la taille et l'emplacement des différents isolants acoustiques. Reportez-vous à l'illustration : B Fixez les isolants acoustiques à température ambiante. 13. Remettez l'appareil en position verticale. 14. Retirez le câble d'alimentation électrique et le tuyau de vidange de leurs supports.
www.aeg.com 16. Retirez les entretoises en plastique. 17. Placez les caches en plastique, fournis dans le sachet du manuel d'utilisation, dans les trous. x4 L'appareil doit être de niveau et stable. Une mise de niveau correcte évite les vibrations, le bruit ou des déplacements de l'appareil au cours de son fonctionnement. Nous vous recommandons de conserver l'emballage et les boulons de transport en vue d'un éventuel déplacement de l'appareil. 3.2 Positionnement et mise de niveau 1.
FRANÇAIS 9 La partie rouge dans la fenêtre « A » témoigne de ce dysfonctionnement. 45 20 O O Assurez-vous que le tuyau d'arrivée d'eau n'est pas en position verticale. 3. Si nécessaire, desserrez la bague de serrage pour bien le positionner. 4. Raccordez le tuyau d'arrivée d'eau à un robinet d'eau froide fileté (3/4 pouce). ATTENTION! Assurez-vous que les raccords ne fuient pas. N'utilisez pas de rallonge si le tuyau d'alimentation est trop court.
www.aeg.com Vérifiez que l'extrémité du tuyau de vidange n'est pas plongée dans l'eau. Il pourrait y avoir un reflux d'eau sale dans l'appareil. 3. À une conduite fixe dotée d'une ventilation spéciale : insérez directement le tuyau dans la conduite d'évacuation. Reportezvous à l'illustration. L'extrémité du tuyau de vidange doit être ventilée en permanence, c'est-à-dire que le diamètre interne du conduit d’évacuation (minimum 38 mm - min.
FRANÇAIS tissus grâce aux différentes phases de pré-mélange qui dissolvent d'abord le produit de lavage puis l'assouplissant dans l'eau avant de les libérer dans le linge. Ainsi, chaque fibre est traitée et lavée. • La technologie ProSense détecte la quantité de linge et calcule la durée du programme en 30 secondes. Le programme de lavage est défini sur mesure pour la charge et le type de linge, sans consommer davantage de temps, d'énergie ou d'eau que nécessaire.
www.aeg.com 5. BANDEAU DE COMMANDE 5.
FRANÇAIS 13 5.2 Affichage MIX Voyant de charge maximale. Le voyant clignote lors de l'estimation de la charge de linge (consultez le paragraphe « Détection de la charge PROSENSE »). Voyant de charge maximale. Il clignote lorsque la charge de linge dépasse la charge maximale prévue pour le programme sélectionné. Indicateur Départ différé. Voyant Hublot verrouillé. L'indicateur numérique peut afficher : • La durée du programme (par ex. • Le départ différé (par ex. ou ). ). • La fin du cycle ( ).
www.aeg.com Voyant Sécurité enfants. Voyant Gain de temps. Indicateur de température. Le voyant tionnez un lavage à froid. apparaît lorsque vous sélec- Indicateur de vitesse d'essorage. Voyant Arrêt cuve pleine. Voyant Extra silence. Voyant de prélavage. Voyant Détachage. Voyant Rinçage plus. 6. MANETTES ET TOUCHES 6.1 Marche/Arrêt Appuyez sur cette touche pendant quelques secondes pour allumer et éteindre l'appareil.
FRANÇAIS 6.4 Essorage L'appareil vidange l'eau automatiquement au bout d'environ 18 heures. Lorsque vous sélectionnez un programme, l'appareil règle automatiquement la vitesse d'essorage maximale. 6.5 Taches/Prélavage Appuyez à plusieurs reprises sur cette touche pour : • Diminuer la vitesse d'essorage. Appuyez à plusieurs reprises sur la touche pour activer une des deux options, ou les deux. Seules les vitesses disponibles pour le programme sélectionné s'affichent.
www.aeg.com Cette option allonge la durée du programme. Si l'option Rinçage Plus est définie comme une option par défaut et que vous sélectionnez un programme de lavage, s'affiche. Dans ce cas, en appuyant sur la touche Rinçage Plus, il est possible de n'ajouter qu'un seul rinçage.
FRANÇAIS Si vous appuyez une quatrième fois sur la touche, l'appareil propose à nouveau un réglage par défaut du programme de lavage. 6.11 Départ Différé Cette option vous permet de différer le départ du programme à un moment qui vous convient mieux. Appuyez à plusieurs reprises sur la touche pour sélectionner le délai souhaité. Le temps augmente par paliers de 30 minutes jusqu'à 90 minutes, puis de 2 heures à 20 heures.
www.aeg.com Programme Description du programme Programme vapeur pour les articles en coton et textiles Vapeur synthétiques. La vapeur peut être utilisée pour le linge sec2) Linge propre ou porté une seule fois. Ce programme réduit les plis et les odeurs3) et détend les fibres. Lorsque le programme est terminé, retirez rapidement le linge du tambour. Après un programme Vapeur, le repassage est facilité. N'utilisez aucun produit de lavage.
FRANÇAIS Programme 19 Description du programme N'utilisez pas d'adoucissant et assurez-vous que le distributeur de produit de lavage ne contient pas de résidus d'adoucissant. Outdoor Articles de sport synthétiques. Ce programme est conçu pour laver en douceur les vêtements de sport modernes, également pour les vêtements pour la gym, le cyclisme, le jogging, et les vêtements d'extérieur similaires. La charge de linge recommandée est de 2.5 kg. Textiles imperméables et respirants.
www.aeg.com Programme Température par défaut Plage de températures Vitesse d'essorage maximale Plage de vitesses d'essorage Synthétiques 40 °C 60 °C - Froid 1200 tr/min 1200 tr/min 400 tr/min 4 kg Délicats 40 °C 40 °C - Froid 1200 tr/min 1200 tr/min 400 tr/min 4 kg Laine/Soie 40 °C 40 °C - Froid 1200 tr/min 1200 tr/min 400 tr/min 2 kg - - 1.
FRANÇAIS 21 ÖKOPower Anti-Allergie ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Taches1) ■ ■ ■ ■ ■ Prélavage ■ ■ ■ ■ ■ Rinçage Plus ■ ■ ■ ■ ■ Éco 2) ■ ■ ■ Gain de Temps 3) ■ ■ ■ Rinçage ■ ■ ■ ■ ■ ■ ■ ■ ■ Essorage ■ ■ ■ ■ ■ ■ ■ ■ ■ Vidange ■ ■ ■ ■ ■ ■ ■ ■ ■ Départ Différé ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Vapeur Plus 1) Douceur Plus ■ ■ Jeans Laine/Soie ■ Outdoor Délicats ■ 20 min.
www.aeg.com 7.2 Woolmark Apparel Care Vert le lavage des vêtements en laine portant une étiquette « lavage à la main », sous réserve que les vêtements soient lavés conformément aux instructions du fabricant de ce lave-linge. Consultez l'étiquette d'entretien du vêtement pour plus d'instructions sur le séchage et le lavage. M1361 Au Royaume-Uni, en Irlande, à Hong Kong ainsi qu'en Inde, le symbole Woolmark est une marque de certification.
FRANÇAIS Pour désactiver/activer les signaux sonores, appuyez simultanément sur les touches Rinçage Plus et Départ Différé pendant 6 secondes. Si vous désactivez les signaux sonores, ils continueront à retentir si l'appareil présente une anomalie. Cette option ajoute deux rinçages et s'affiche. 9.4 Douceur Plus Sélectionnez l'option Douceur Plus pour optimiser la distribution d'assouplissant et rendre le linge plus doux. Il est recommandé lorsque vous utilisez de l'assouplissant. 9.
www.aeg.com 10.3 Ajout du produit de lavage et des additifs 1 2 3. Pour utiliser de la lessive en poudre, tournez le volet vers le haut. Compartiment pour la phase de prélavage et le programme de trempage. Compartiment pour la phase de lavage. Compartiment réservé aux additifs liquides (assouplissant, amidon). Niveau maximal pour la quantité d'additifs liquides. Compartiment réservé au détachant. Volet pour produit de lavage en poudre ou liquide.
FRANÇAIS Avec le volet en position BASSE : • N'utilisez pas de lessives liquides gélatineuses ou épaisses. • Ne versez pas de lessive liquide audelà du niveau maximal indiqué sur le volet. • Ne sélectionnez pas de phase de prélavage. • Ne sélectionnez pas la fonction Départ différé. 5. Dosez le produit de lavage et l'assouplissant. 6. Fermez soigneusement le distributeur de produit de lavage. 25 3. Si nécessaire, sélectionnez une ou plusieurs options en appuyant sur les touches correspondantes.
www.aeg.com 2. Appuyez à plusieurs reprises sur la touche Départ Différé jusqu'à ce que s'affiche. 3. Appuyez de nouveau sur la touche Départ/Pause pour lancer le programme immédiatement. Modification du départ différé au cours du décompte Pour modifier le départ différé : 1. Appuyez sur la touche Départ/Pause pour mettre l'appareil en pause. Le voyant correspondant clignote. 2. Appuyez à plusieurs reprises sur la touche Départ Différé jusqu'à ce que le départ différé souhaité s'affiche. 3.
FRANÇAIS programme (les flèches clignotent en alternance). Si vous sélectionnez Vapeur Plus, les voyants de la phase à la vapeur s'allument. La phase à la vapeur est en cours : . La phase anti-froissage est en cours : . 10.10 Interruption d'un programme et modification des options Lorsque le programme est en cours, vous ne pouvez changer que quelques options : 1. Appuyez sur la touche Départ/Pause. Le voyant correspondant clignote. 2. Modifiez les options.
www.aeg.com formation de moisissures et l'apparition de mauvaises odeurs. 5. Fermez le robinet d'eau. 10.14 Vidange de l'eau après la fin du cycle Si vous avez sélectionné un programme ou une option qui ne vidange pas l'eau du dernier rinçage, le programme se termine, mais : • L'indicateur , le voyant d'option et le voyant Hublot fermé ou s'affichent. Le voyant de la phase en clignote. cours • Le tambour tourne toujours à intervalles réguliers pour éviter que le linge ne se froisse.
FRANÇAIS • Traitez au préalable les taches tenaces. • Lavez les taches incrustées avec un produit spécial. • Traitez les rideaux avec précautions. Retirez les crochets et placez les rideaux dans un sac de lavage ou une taie d'oreiller. • Ne lavez pas d'articles sans ourlet ou déchirés. Utilisez un sac de lavage pour les articles très petits et/ou délicats (par exemple les soutiensgorge à armatures, les ceintures, les bas, etc.).
www.aeg.com 12. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 12.1 Nettoyage extérieur Nettoyez uniquement l'appareil à l'eau chaude avec un savon doux. Séchez complètement toutes les surfaces. ATTENTION! N'utilisez pas d'alcool, de solvants ni de produits chimiques. Pour éliminer ces dépôts et assainir l'intérieur de l'appareil, effectuez régulièrement un lavage d'entretien (au moins une fois par mois) : 1. Retirez le linge du tambour. 2.
FRANÇAIS 1. Ouvrez le distributeur. Appuyez sur le loquet vers le bas comme indiqué sur l'illustration, puis retirez le distributeur. 31 programme de rinçage sans vêtement dans le tambour. 1 2 2. Retirez la partie supérieure du compartiment réservé à l'additif pour faciliter le lavage, et passez-le sous l'eau courante chaude pour éliminer toute trace d'accumulation de lessive. Après le nettoyage, remettez la partie supérieure en place. 12.
www.aeg.com 2 1 2 1 2. Placez un récipient adéquat audessous de l'accès à la pompe de vidange pour recueillir l'eau s'écoulant. 3. Serrez les deux leviers et tirez la conduite de vidange vers l'avant pour l'ouvrir. 1 7. Fermez la conduite de vidange et tournez le filtre dans le sens antihoraire pour le retirer. 2 1 1 2 4. Laissez l'eau s'écouler. 5. Lorsque le récipient est rempli d'eau, refermez la conduite de vidange et videz le récipient. 6.
FRANÇAIS 33 12.8 Nettoyage du tuyau d'arrivée d'eau et du filtre de la vanne Il est recommandé de nettoyer occasionnellement les deux filtres du tuyau d'arrivée d'eau et la valve pour éliminer les dépôts accumulés avec le temps : 1. Retirez le tuyau d'arrivée d'eau du robinet et nettoyez le filtre. 11. Replacez le filtre dans les guides prévus en le tournant dans le sens horaire. Assurez-vous de visser correctement le filtre pour empêcher les fuites. 1 2 2 3 1 2.
www.aeg.com 4. Lorsque vous rebranchez le tuyau à l'arrière de l'appareil, tournez-le vers la gauche ou la droite (et non en position verticale) en fonction de la position du robinet. 2. Démarrez le programme pour vidanger l'eau. 12.10 Précautions contre le gel Si l'appareil est installé dans un local où la température peut être négative, évacuez toute l'eau restant dans le tuyau d'alimentation et la pompe de vidange. 45° 20° 12.
FRANÇAIS • - L'alimentation électrique est instable. Attendez que l'alimentation électrique se stabilise. 35 • - Il n'y a aucune communication entre les composants électroniques de l'appareil. Éteignez puis rallumez l'appareil. • - Le système de sécurité antidébordement s'est déclenché. Débranchez l'appareil et fermez le robinet d'arrivée d'eau. Contactez le service après-vente agréé. AVERTISSEMENT! Éteignez l'appareil avant de procéder à la vérification. 13.
www.aeg.com Problème Solution possible L'appareil ne vidange pas l'eau. • Assurez-vous que le siphon de l'évier n'est pas obstrué. • Assurez-vous que le tuyau de vidange n'est pas tordu ni plié. • Assurez-vous que le filtre de vidange n'est pas obstrué. Nettoyez le filtre si nécessaire. Reportez-vous au chapitre « Entretien et nettoyage ». • Vérifiez que le raccordement du tuyau de vidange est correct. • Sélectionnez le programme de vidange si vous avez choisi un programme sans phase de vidange.
FRANÇAIS 37 Problème Solution possible Les résultats de lavage ne sont pas satisfaisants. • Augmentez la quantité de produit de lavage ou utilisez-en un autre. • Utilisez des produits spéciaux pour enlever les taches tenaces avant de laver le linge. • Veillez à sélectionner la bonne température. • Réduisez la charge de linge. Il y a trop de mousse • Réduisez la quantité de produit de lavage. dans le tambour au cours du cycle de lavage.
www.aeg.com 5. Sortez le linge et refermez le hublot. 6. Fermez le volet du filtre. 14. VALEURS DE CONSOMMATION Les données de ce tableau sont approximatives. Les données peuvent varier pour différentes raisons : la quantité et le type de linge, la température ambiante ou de l'eau. Au cours du programme de lavage, la technologie Prosense peut faire varier la durée du lavage et les valeurs de consommation.
FRANÇAIS Mode « Éteint » (W) Mode « Veille » (W) 0.30 0.30 39 Les informations fournies dans le tableau ci-dessus sont conformes à la directive d'application 1015/2010 de la réglementation 2009/125/CE de la commission européenne. 15.
www.aeg.com 16.3 Kit de superposition AVERTISSEMENT! N'installez pas le sèche-linge sous le lave-linge. 16.4 Socle à tiroir Le sèche-linge ne peut-être superposé au-dessus du lave-linge qu'en utilisant le kit de superposition adapté, fabriqué et agréé par AEG. Pour surélever votre appareil et faciliter le chargement et le déchargement du linge. Assurez-vous de la compatibilité du kit de superposition en vérifiant la profondeur de vos appareils.
FRANÇAIS 41
www.aeg.
FRANÇAIS 43
157008690-A-022017 www.aeg.