L8FS76499 USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................4 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 10 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com 1.2 Allgemeine Sicherheit • • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Überschreiten Sie nicht die maximale Beladungsmenge von 9 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • • • • • • • • • verriegeln und dadurch interne Schäden zu vermeiden. Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk. Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. Halten Sie sich an die mitgelieferte Montageanleitung. Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist.
www.aeg.com Substanzen verschmutzt sind. Die Gummiteile der Waschmaschine könnten beschädigt werden. Waschen Sie solche Textilien mit der Hand vor, bevor Sie sie in die Waschmaschine geben. • Berühren Sie während des Ablaufs eines Programms nicht die Glastür. Das Glas kann sehr heiß werden. 2.5 Service • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung.
DEUTSCH 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. Aus dem Ablaufschlauch könnte Wasser austreten. Dies ist auf den Gerätetest mit Wasser im Werk zurückzuführen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 10.
www.aeg.com Das Gerät muss einen waagerechten und festen Stand haben. Durch eine korrekte waagrechte Ausrichtung des Geräts werden Vibrationen, Geräusche und ein Wandern des Geräts während des Betriebs vermieden. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren. 3.2 Aufstellen und Ausrichten 1. Stellen Sie das Gerät auf einen ebenen, festen Boden. Stellen Sie sicher, dass die Luftzirkulation unter dem Gerät nicht durch Teppiche beeinträchtigt wird.
DEUTSCH 1. Formen Sie den Ablaufschlauch zu einem U und verlegen Sie ihn in der Kunststoffführung. VORSICHT! Achten Sie darauf, dass die Anschlüsse dicht sind. Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist. Wenden Sie sich an den Kundendienst, um einen anderen Zulaufschlauch zu erhalten. 2. Am Rande eines Beckens Befestigen Sie die Führung am Wasserhahn oder an der Wand. Stellen Sie sicher, dass die Kunststoffführung beim Abpumpen nicht herausrutschen kann. 3.
www.aeg.com den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Orientieren Sie sich an der Abbildung. Das Ende des Ablaufschlauchs muss stets belüftet sein, d. h. der Innendurchmesser des Ablaufrohrs (min. 38 mm min. 1,5") muss größer sein als der Außendurchmesser des Ablaufschlauchs. 4. Sieht das Ende des Ablaufschlauchs wie in der Abbildung gezeigt aus, können Sie es direkt in das Standrohr drücken. 5.
DEUTSCH und beseitigen Falten in trockenen Kleidungsstücken, sodass sie nur leicht gebügelt werden müssen. Die Option Plus Dampf beendet jedes Programm mit sanftem Dampf, um die Fasern aufzulockern und Falten zu verringern. So wird das Bügeln einfacher! • Die Option Flecken behandelt hartnäckige Flecken vor und optimiert die Wirksamkeit des Fleckentferners.
www.aeg.com 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 4 5 12 1 Programmwahlschalter 2 Display 3 Sensortaste Eco (Eco) 4 Sensortaste Zeit Sparen (Zeit Sparen) 5 Sensortaste Spülen (Spülen) • Option Extra Spülen (Extra Spülen) • Waschprogramm überspringen Option Nur Spülen (Nur Spülen) 6 Sensortaste Start/Pause (Start/Pause) 7 Sensortaste Flecken/Vorwäsche (Flecken/Vorw.
DEUTSCH 13 5.2 Display MIX Anzeige der max. Beladung. Die Anzeige blinkt während der Messung der Wäschemenge (siehe Abschnitt ProSense Beladungserkennung). Anzeige des max. zulässigen Wäschegewichts. Sie blinkt, wenn die Beladung das für das eingestellte Programm angegebene Gewicht überschreitet. Türverriegelungsanzeige. Zeitvorwahlanzeige. Die Digitalanzeige zeigt Folgendes an: • Programmdauer (z. B. • Zeitvorwahl (z. B. ). oder ). • Programmende ( ). • Fehlercode (z. B. ). Hauptwaschganganzeige.
www.aeg.com Energiesparanzeigen. Die Anzeige erscheint, wenn ein Baumwollprogramm mit 40 °C oder 60 °C gewählt wird. Zeitsparanzeige. Schleuderdrehzahlanzeige. Spülstoppanzeige. Anzeige Leise. Temperaturanzeige. Die Anzeige mit kaltem Wasser gewählt wurde. erscheint, wenn ein Waschgang 6. PROGRAMMWAHLSCHALTER UND TASTEN 6.1 Ein/Aus 6.3 Temp. Halten Sie diese Taste einige Sekunden lang gedrückt, um das Gerät ein- oder auszuschalten. Beim Ein- und Ausschalten ertönen zwei verschiedene Melodien.
DEUTSCH beendet, aber es steht Wasser in der Trommel. Auf dem Display erscheint die Anzeige . Die Tür bleibt verriegelt und die Trommel dreht sich regelmäßig, um Knitterbildung zu reduzieren. Sie müssen das Wasser abpumpen, um die Tür entriegeln zu können. Wenn Sie die Taste Start/Pause drücken, führt das Gerät den Schleudergang aus und pumpt das Wasser ab. Das Gerät pumpt das Wasser nach etwa 18 Stunden automatisch ab. • Die Option Leise einzuschalten.
www.aeg.com Die Dampfphase vermindert die Knitterbildung und erleichtert das Bügeln. Während der Dampfphase blinkt die Anzeige im Display. Mit dieser Option kann sich die Programmdauer verlängern. Am Programmende erscheint eine Null im Display, die Anzeige leuchtet konstant und die Anzeige beginnt zu blinken. Die Trommel führt 30 Minuten lang sanfte Bewegungen aus, um die Wirkung des Dampfs aufrecht zu erhalten.
DEUTSCH 17 6.11 Start/Pause Berühren Sie die Taste Start/Pause, um das Gerät zu starten, anzuhalten oder ein laufendes Programm zu unterbrechen. 7. PROGRAMME 7.1 Programmübersicht Waschprogramme Programm Programmbeschreibung Waschprogramme Baumwolle Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte.
www.aeg.com Programm Programmbeschreibung Dampfprogramm für Baumwolle und pflegeleichte Wäsche. Dampf Dampf kann verwendet werden für getrocknete2), gewaschene oder einmal getragene Wäschestücke. Dieses Programm reduziert Falten und Gerüche3) und lockert die Fasern auf. Nehmen Sie nach Ablauf des Programms die Wäsche schnell aus der Trommel. Nach einem Dampfprogramm lässt sich die Wäsche mühelos bügeln. Verwenden Sie kein Waschmittel.
DEUTSCH Programm Outdoor 19 Programmbeschreibung Verwenden Sie keinen Weichspüler, und stellen Sie sicher, dass sich keine Weichspülerrückstände in der Waschmittelschublade befinden. Outdoorkleidung, technisches Gewebe, Sportgewebe, imprägnierte und atmungsaktive Jacken, Jacken mit herausnehmbarem Fleeceteil oder Innenwattierung. Die empfohlene Beladung beträgt 2.5 kg.
www.aeg.com Programm Standardtemperatur Temperaturbereich Maximale Schleuderdrehzahl Schleuderdrehzahlbereich Feinwäsche 40 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 4 kg Wolle/Seide 40 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 2 kg Maximale Beladung Dampfprogramm - Dampf - 1.5 kg Waschprogramme 30 °C 60 °C - 30 °C 1400 U/min 1400 U/min – 400 U/min 5 kg 60 °C 1400 U/min 1400 U/min – 400 U/min 9 kg 20 Min.
Nur Abpumpen ■ ■ ■ ■ ■ ■ ■ Nur Schleudern ■ ■ ■ ■ ■ ■ ■ Flecken 1) ■ ■ ■ ■ Vorwäsche ■ ■ ■ ■ Extra Spülen ■ ■ ■ Nur Spülen ■ ■ ■ ■ ■ ■ Zeit Sparen 3) ■ ■ ■ Zeitvorwahl ■ ■ ■ Plus Dampf1) ■ ■ Soft Plus ■ ■ 2) ■ ■ ■ ■ ■ ■ ■ Daunen Anti-Allergie ■ Outdoor ÖKOPower 20 Min.
www.aeg.com 8. EINSTELLUNGEN 8.1 Kindersicherung Diese Option verhindert, dass Kinder mit dem Bedienfeld spielen. • Berühren Sie zum Ein-/Ausschalten dieser Option die Tasten Flecken/ Vorw. und U/Min. gleichzeitig, bis die Anzeige im Display leuchtet/ erlischt. Sie können diese Option einschalten: • Nachdem Sie die Taste Start/Pause berührt haben: Alle Tasten und der Programmwahlschalter (mit Ausnahme der Taste Ein/Aus) sind ausgeschaltet.
DEUTSCH 5. Stellen Sie ein Baumwollprogramm mit der höchsten Temperatur ein und starten Sie das Programm ohne Wäsche. 23 So werden alle eventuellen Verunreinigungen aus Trommel und Bottich entfernt. 10. TÄGLICHER GEBRAUCH WARNUNG! Siehe Kapitel Sicherheitshinweise. 10.1 Einschalten des Geräts 1. Stecken Sie den Netzstecker in die Netzsteckdose. 2. Öffnen Sie den Wasserhahn. 3. Halten Sie die Taste Ein/Aus einige Sekunden lang gedrückt, um das Gerät einzuschalten.
www.aeg.com 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. Halten Sie sich immer an die Anweisungen auf der Verpackung der Waschmittel. Wir empfehlen Ihnen aber, die Höchstmenge ( ) nicht zu überschreiten. Diese Menge garantiert die besten Waschergebnisse. Entfernen Sie nach dem Waschgang bei Bedarf Waschmittelreste aus der Waschmittelschublade. 10.4 Überprüfen Sie die Position der Klappe 1. Ziehen Sie die Waschmittelschublade bis zum Anschlag heraus. 2.
DEUTSCH 10.5 Einstellen eines Programms 1. Drehen Sie den Programmwahlschalter auf das gewünschte Waschprogramm. Die entsprechende Programmanzeige leuchtet auf. Die Kontrolllampe der Taste Start/Pause blinkt. Das Display zeigt die maximal zulässige Füllmenge für das Programm, die Standardtemperatur, die maximale Schleuderdrehzahl, die Programmphasen (falls verfügbar) und die voraussichtliche Programmdauer an. 2. Berühren Sie die entsprechenden Tasten, um die Temperatur und/oder Schleuderdrehzahl zu ändern.
www.aeg.com 1. Das Gerät erkennt die Ladung innerhalb von 30 Sekunden: Die Z. B. die Wasch- oder Vorwaschphase und der ZeitAnzeige Doppelpunkt blinken, die Trommel dreht sich kurz. 2. Am Ende der Beladungskennung wird ausgeführt: erlischt die Anzeige und der ZeitDoppelpunkt hört auf zu blinken. Die Programmdauer wird entsprechend angepasst und kann sich verlängern oder verkürzen. Nach weiteren 30 Sekunden beginnt das Wasser einzulaufen.
DEUTSCH 2. Drücken Sie die Taste Ein/Aus erneut, um das Gerät einzuschalten. Anschließend können Sie ein neues Waschprogramm einstellen. Wurde die ProSense-Phase bereits beendet und läuft Wasser in das Gerät ein, startet das neue Programm ohne die ProSense-Phase zu wiederholen. Um Wasser und Waschmittel nicht zu verschwenden, wird das Wasser nicht abgepumpt. Das Display zeigt die maximale Programmdauer an, die etwa 20 Minuten nach dem Start des neuen Programms aktualisiert wird. 10.
www.aeg.com • Wenn Sie gewählt haben, pumpt das Gerät das Wasser ab und schleudert. • Wenn Sie gewählt haben, pumpt das Gerät nur das Wasser ab. Die Optionsanzeige oder erlischt, während die Anzeige blinkt und dann erlischt. 3. Wenn das Programm beendet ist und die Türverriegelungsanzeige erlischt, können Sie die Tür öffnen. 4. Halten Sie die Taste Ein/Aus einige Sekunden lang gedrückt, um das Gerät auszuschalten. In jedem Fall pumpt das Gerät das Wasser nach etwa 18 Stunden automatisch ab. 10.
DEUTSCH b. verteilen Sie die Wäsche mit der Hand neu, so dass die Wäschestücke gleichmäßig verteilt sind. c. Drücken Sie die Taste Start/ Pause. Die Schleuderphase wird fortgesetzt. 11.2 Hartnäckige Flecken Für manche Flecken sind Wasser und Waschmittel nicht ausreichend. Wir empfehlen, diese Flecken vorzubehandeln, bevor Sie die entsprechenden Textilien in das Gerät geben. Spezial-Fleckentferner sind im Handel erhältlich.
www.aeg.com VORSICHT! Verwenden Sie keinen Alkohol, keine Lösungsmittel und keine Chemikalien. VORSICHT! Reinigen Sie die Metallflächen nicht mit einem Reinigungsmittel auf Chlor-Basis. 12.2 Entkalkung Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Entkalkers für Waschmaschinen. Prüfen Sie die Trommel regelmäßig auf Kalkablagerungen.
DEUTSCH 31 1 2 2. Entfernen Sie das Oberteil des Pflegemittelfachs, um die Reinigung zu vereinfachen, und spülen Sie es mit fließendem warmen Wasser aus, um das angesammelte Waschmittel zu beseitigen. Setzen Sie nach der Reinigung das Oberteil wieder ein. 12.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. 3.
www.aeg.com 6. Wiederholen Sie die Schritte 4 und 5, bis kein Wasser mehr herausfließt. 7. Drehen Sie das Sieb gegen den Uhrzeigersinn, um es zu entfernen. 2 1 2. Stellen Sie einen geeigneten Behälter unter die Öffnung der Ablaufpumpe, um das abfließende Wasser aufzufangen. 3. Öffnen Sie den Schacht nach unten. Halten Sie beim Herausnehmen des Siebs einen Lappen bereit, um austretendes Wasser aufzuwischen. 4.
DEUTSCH 33 1 2 3 2. Lockern Sie die Ringmutter, um den Zulaufschlauch vom Gerät zu entfernen. 12. Schließen Sie die Pumpenabdeckung. 2 1 Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: a. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. b. Starten Sie das Programm zum Abpumpen des Wassers. 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 12.
www.aeg.com 0 °C erreichen oder unter 0 °C sinken kann, entfernen Sie das im Zulaufschlauch und in der Ablaufpumpe verbliebene Wasser. 45° 20° 12.9 Notentleerung Kann das Gerät das Wasser nicht abpumpen, führen Sie den unter „Reinigen des Ablauffilters“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. 1. Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Schließen Sie den Wasserhahn. 3.
DEUTSCH Ist das Gerät überladen, nehmen Sie einige Wäschestücke aus der Trommel und/oder drücken Sie die Tür zu und berühren Sie gleichzeitig die Taste Start/Pause, bis die Anzeige aufhört zu blinken (siehe Abbildung unten). 35 • - Die Stromzufuhr ist nicht konstant. Warten Sie, bis die Netzspannung wieder konstant ist. • - Keine Kommunikation zwischen den elektronischen Bauteilen des Geräts. Schalten Sie das Gerät aus und wieder ein. • – Das Aqua-Control-System ist eingeschaltet.
www.aeg.com Störung Mögliche Abhilfe Das Wasser, das in das • Vergewissern Sie sich, dass sich der Ablaufschlauch in der Gerät einläuft, wird sofort richtigen Höhe befindet. Der Schlauch ist möglicherweise abgepumpt. zu niedrig angebracht. Siehe hierzu „Montage“. Das Gerät pumpt das Wasser nicht ab. • Stellen Sie sicher, dass der Siphon nicht verstopft ist. • Vergewissern Sie sich, dass der Ablaufschlauch nicht geknickt oder zu stark gekrümmt ist.
DEUTSCH 37 Störung Mögliche Abhilfe Das Gerät verursacht ein ungewöhnliches Geräusch und vibriert. • Stellen Sie sicher, dass das Gerät richtig ausgerichtet ist. Siehe hierzu „Montage“. • Überzeugen Sie sich, dass das Verpackungsmaterial und/ oder die Transportsicherungen entfernt wurden. Siehe hierzu „Montage“. • Füllen Sie mehr Wäsche ein. Die Beladung ist möglicherweise zu gering. Die Programmdauer erhöht oder verringert sich während der Ausführung des Programms.
www.aeg.com VORSICHT! Verletzungsgefahr! Vergewissern Sie sich, dass die Trommel sich nicht dreht. Warten Sie sonst, bis die Trommel zum Stillstand gekommen ist. 2. Ziehen Sie den Netzstecker aus der Netzsteckdose. 3. Öffnen Sie die Filterklappe. 4. Drücken Sie den Auslöser für die Notfallentriegelung nach unten und öffnen Sie gleichzeitig die Gerätetür. Stellen Sie sicher, dass der Wasserstand in der Trommel nicht zu hoch ist.
DEUTSCH Programme Beladung (kg) EnergieWasserUngefähverbrauch verbrauch re Pro(kWh) (Liter) grammdauer (in Minuten) Restfeuchte (%)1) Feinwäsche 40 °C 4 0.60 59 89 35 Wolle/Seide 30 °C 2 0.35 58 60 30 9 0.53 56 224 52 4.5 0.31 41 186 52 4.5 0.32 40 183 52 Standardprogramme Baumwolle Standardprogramm Baumwolle 60 °C Standardprogramm Baumwolle 60 °C Standardprogramm Baumwolle 40 °C 1) Am Ende der Schleuderphase. Aus-Zustand (W) Ein-Zustand (W) 0.30 0.
www.aeg.com Energieeffizienzklasse Schleuderdrehzahl A+++ Höchstwert 1400 U/min 1) Schließen Sie den Zulaufschlauch an einen Wasserhahn mit einem 3/4'' -Außengewinde an. 16. ZUBEHÖR 16.1 Verfügbar bei www.aeg.com/shop oder einem autorisierten Händler Nur mit geeignetem, von AEG zugelassenem Zubehör können die Sicherheitsstandards des Geräts gewährleistet werden. Werden nicht zugelassene Teile verwendet, erlischt jeglicher Gewährleistungsanspruch. 16.
DEUTSCH 41 Lesen Sie die mit dem Zubehör gelieferte Gebrauchsanleitung sorgfältig durch. 17. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte. Entsorgen Sie * Geräte mit diesem Symbol nicht mit dem Hausmüll. Bringen Sie das Gerät zu Ihrer örtlichen Sammelstelle oder wenden Sie sich an Ihr Gemeindeamt.
www.aeg.
DEUTSCH 43
157004162-A-152017 www.aeg.