L8FS86499 USER MANUAL EN User Manual Washing Machine
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................4 3. INSTALLATION............................................................................................................6 4. PRODUCT DESCRIPTION.........................................................................................11 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com by clients in hotels, motels, bed & breakfast and other residential type environments; – areas for communal use in blocks of flats or in launderettes. Do not exceed the maximum load of 9 kg (refer to the "Programme chart" chapter). The operating water pressure at the water entry point from the outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar (0.8 MPa). The ventilation opening in the base must not be covered by a carpet, mat, or any floor covering.
ENGLISH • The floor area on which the appliance is to be installed must be flat, stable, heat resistant and clean. • Make sure that there is air circulation between the appliance and the floor. • When the appliance is in its permanent position, check if it is levelled correctly with the aid of a spirit level. If it is not, adjust the feet accordingly. • Do not install the appliance directly above a floor drain. • Do not spray water on the appliance and do not expose it to excessive humidity.
www.aeg.com • Visible LED radiation, do not look directly into the beam. • The LED lamp is dedicated to drum lighting. This lamp cannot be reused for other lighting purposes. • To replace the internal lighting, contact the Authorised Service Centre. 2.6 Service • To repair the appliance contact an Authorised Service Centre. • Use original spare parts only. • Disconnect the appliance from the mains electrical and water supplies.
ENGLISH 5. Carefully put the appliance down on its rear side. 6. Put the front polystyrene packaging element on the floor under the appliance. 7 CAUTION! Do not use alcohol, solvents or chemical products. 9. Make sure to identify the different sizes and the positions of the sound barriers. Refer to the illustration: A Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. 1 2 B • A (FRONT) = Front of the appliance • B (BACK) = Rear of the appliance 10.
www.aeg.com Attach the sound barriers at a room temperature. 13. Pull up the appliance in vertical position. We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 14. Remove the power supply cable and the drain hose from the hose holders. 3.2 Positioning and levelling 1. Install the appliance on a flat hard floor. Make sure that the appliance does not touch the wall or other units. 2. Loosen or tighten the feet to adjust the level.
ENGLISH A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. When the machine is installed on a plinth or if a washer dryer is stacked on the washing machine, use the accessories described in chapter 'Accessories'. Read carefully the instructions supplied with the appliance and with the accessory. 9 4. Connect the water inlet hose to the cold water tap with 3/4" thread.
www.aeg.com You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. It is possible to connect the drain hose in different ways: 1. Make a U shape with the drain hose and put it around the plastic hose guide. 2. On the edge of a sink - Fasten the guide to the water tap or to the wall. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm min. 1.
ENGLISH 11 6. Position the hose directly to a builtin drain pipe in the room wall and tighten it with a clamp. 4. PRODUCT DESCRIPTION 4.1 Special features Your new washing machine meets all modern requirements for an effective treatment of laundry with low water, energy and detergent consumption and proper care of fabric.
www.aeg.com 4.2 Appliance overview 1 2 3 10 9 11 4 5 6 12 13 7 8 1 2 3 4 5 6 7 Worktop Detergent dispenser Control panel Door handle Internal light Rating plate Drain pump filter 8 9 10 11 12 13 Feet for levelling the appliance Drain hose Inlet hose connection Mains cable Transit bolts Hose support 5. CONTROL PANEL 5.1 Control panel description 3 2 1 Programme Baumwolle Pflegeleicht Feinwäsche Wolle/Seide Dampf ÖKOPower Anti-Allergie 20 min.
ENGLISH 13 1 Programme dial 2 Display 3 Energy saving touch button (Eco) 7 Extra rinse touch button (Extra Spülen) 8 Delay start touch button (Zeitvorwahl) 4 Time saving touch button (Zeit Sparen) 5 Skipping phase touch button (Option) • Wash phase skipping (Nur Spülen) 9 Super steam touch button (Plus Dampf) Anti-stain and prewash touch button 10 (Flecken/Vorw.) 11 Spin reduction touch button (U./Min.
www.aeg.com The digital indicator can show: ). • Programme duration (e. g. • Delay time (e. g. or ). • Cycle end ( ). • Warning code (e.g. ). Energy saving indicators. The indicator appears by selecting a programme for cotton at 40 °C or 60 °C. Washing phase indicator: it flashes during prewash and wash phase. Rinsing phase indicator: it flashes during rinse phase. The indicator appears when the Soft Plus option is activated. Spin and drain phase indicator.
ENGLISH For more details, refer to Stand-by paragraph in Daily Use chapter. 6.2 Introduction The options/functions are not selectable with all washing programmes. Check the compatibility between options/functions and washing programmes in the "Programme Chart". An option/function can exclude another one, in this case the appliance doesn't allow you to set the incompatible options/functions together. Make sure the screen and touch buttons are always clean and dry. 6.3 Temp.
www.aeg.com Use this option to add a prewash phase at 30 °C before the washing phase. This option is recommended for heavily soiled laundry, especially if containing sand, dust , mud and other solid particles. This option can increase the programme duration. 6.6 Extra Spülen With this option you can add up to 3 rinses accordingly to the selected washing programmes. Useful for people allergic to detergents and in areas where the water is soft. indicator shows the selected The number of rinses.
ENGLISH • Nur Spülen at first touch. The washing programme starts from the rinsing phase by skipping the wash phase. All set options (except permanent extra rinse) are deselected automatically. • Nur Schleudern at second touch. The appliance skips wash and rinse phase. • Nur Abpumpen at third touch. The appliance performs only the drain phase. At firth touch the appliance proposes the default setting of the washing programme again. 17 Touch the button repeatedly to set the required delay.
www.aeg.com Programme Programme description Machine washable wool, hand washable wool and other Wolle/Seide fabrics with «hand washing» care symbol1). Steam programme Steam programme for cotton and synthetic items. Steam Dampf can be used for dried2), washed or worn once laundry. This programme reduce creases and odours3) and relaxes the fibres. When the programme is completed, quickly remove the laundry from the drum. After a steam programme, ironing becomes effortless. Do not use any detergent.
ENGLISH Programme 19 Programme description Do not use fabric softener and make sure that there is no softener residue in the detergent dispenser. Outdoor Outdoor clothing, technical, sport fabrics, waterproof and breathable jackets, shell jackets with a removable fleece or inner insulation. The recommended laundry load is 2.5 kg. This programme can also be used as water-repellent restoring cycle, specifically tailored for treating clothes with a hydrophobic coating.
www.aeg.com Programme Default temperature Reference spin Temperature range speed Spin speed range Maximum load - - 1.5 kg 30 °C 60 °C - 30 °C 1400 rpm 1400 rpm - 400 rpm 5 kg 60 °C 1400 rpm 1400 rpm - 400 rpm 9 kg 20 Min. - 3 kg 30 °C 40 °C - 30 °C 1200 rpm 1200 rpm - 400 rpm 3 kg Outdoor 30 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm Daunen 40 °C 60 °C - 30 °C 800 rpm 800 rpm - 400 rpm Dampf ÖKOPower Anti-Allergie 2.5 kg1) 1 kg2) 3 kg 1) Washing programme.
Feinwäsche ÖKOPower Anti-Allergie 20 Min. - 3 kg Outdoor Daunen Nur Spülen ■ ■ ■ ■ ■ ■ ■ ■ ■ Nur Schleudern ■ ■ ■ ■ ■ ■ ■ ■ ■ Nur Abpumpen ■ ■ ■ ■ ■ ■ ■ ■ ■ Zeitvorwahl ■ ■ ■ ■ ■ ■ ■ ■ ■ Plus Dampf1) ■ ■ Soft Plus ■ ■ Dampf Wolle/Seide Pflegeleicht 21 Baumwolle ENGLISH ■ ■ ■ ■ ■ ■ 1) This option is not available with temperature lower than 40 °C. 2) This option is not available with a temperature lower than 30 °C.
www.aeg.com 5. Set and start a programme for cotton at the highest temperature without any laundry in the drum. This removes all possible dirt from the drum and the tub. 9. SETTINGS 9.1 Child Lock With this option you can prevent that the children play with the control panel. • To activate/deactivate this option, touch the Flecken/Vorw. and the Extra Spülen buttons simultaneously until the indicator comes on/goes off on the display.
ENGLISH 10.1 Using weight sensors For a correct use of the weight sensor, the drum must be empty when activating the appliance. Set the programme BEFORE you put the laundry in the drum. 10.2 Before activating the appliance 1. Make sure that the mains plug is connected to the mains socket. 2. Make sure that the water tap is open. 10.3 Activating the appliance and setting a programme 1. Press button Ein /Aus for a few seconds to activate the appliance. A short tune sounds (if activated).
www.aeg.com 10.5 Filling the detergent and additives 1 2 3. To use powder detergent, turn the flap up. Compartment for prewash phase an soak programme. Compartment for washing phase. Compartment for liquid additives (fabric conditioner, starch). Maximum level for quantity of liquid additives. Compartment for stain remover. Flap for powder or liquid detergent.
ENGLISH With the flap in the position DOWN: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid detergent than the limit shown on the flap. • Do not set the prewash phase. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser. 25 the desired delay time. The indicator comes on. 2. Touch the Start/Pause button. The appliance starts the countdown of the delay start.
www.aeg.com the minimum possible time. The programme duration could increase or decrease. The ProSense detection is carried out with complete washing programmes only (no skipping phase selected). 10.12 Cancelling a running programme 10.10 Programme phase indicators When the programme starts the indicator of the running phase flashes and the other phase indicators are steady on. E.g. the washing or pre wash phase is .
ENGLISH 10.14 End of the programme When the programme has finished, the appliance stops automatically. The acoustic signals operate (if they are active). In the display all washing phase indicators become steady and the time 27 • The door stays locked. • You must drain the water to open the door: 1. If necessary, touch the U./Min. button to decrease the spin speed proposed by the appliance. 2. Touch the Start/Pause button: area shows . • If you have set , the appliance drains the water and spins.
www.aeg.com 11. HINTS AND TIPS WARNING! Refer to Safety chapters. 11.1 The laundry load • Divide the laundry into: white, coloured, synthetics, delicates and wool. • Follow the washing instructions on the laundry care labels. • Do not wash white and coloured items together. • Some coloured items can discolour with the first wash. We recommend that you wash them separately for the first couple of times. • Button up pillowcases, close zippers, hooks and poppers. Tie up belts. • Empty pockets and unfold.
ENGLISH 11.5 Water hardness If the water hardness in your area is high or moderate, we recommend that you use a water softener for washing machines. In areas where the water hardness is soft it is not necessary to use a water softener. 29 To find out the water hardness in your area, contact your local water authority. Use the correct quantity of water softener. Follow the instructions that you find on the packaging of the product. 12. CARE AND CLEANING WARNING! Refer to Safety chapters. 12.
www.aeg.com Always follow the instructions that you find on the packaging of the product. Do not clean the drum with acidic descaling products, scouring products containing chlorine or iron or steel. cleaning, replace the top part in its position. For a thorough clean: 1. Clean the drum with special products for stainless steel. Always follow the instructions that you find on the packaging of the product. 2.
ENGLISH 31 Regularly check the drain pump filter and make sure that it is clean. Clean the drain pump if: • The appliance does not drain the water. • The drum does not turn. • The appliance makes an unusual noise because of the blockage of the drain pump. • The display shows the alarm code . WARNING! • Do not remove the filter while the appliance operates. • Do not clean the pump if the water in the appliance is hot. Wait until the water cools down 4.
www.aeg.com rotate, contact the Authorised Service Centre. 2 1 10. Clean the filter under the water tap. When you drain the water with the emergency drain procedure, you must activate the drain system again: a. Put 2 litres of water in the main wash compartment of the detergent dispenser. b. Start the programme to drain the water. 12.8 Cleaning the inlet hose and the valve filter 11. Put the filter back into the special guides by turning it clockwise.
ENGLISH 33 12.9 Emergency drain If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain pump' paragraph. If necessary, clean the pump. When you drain the water with the emergency drain procedure, you must activate the drain system again: 3. Clean the valve filter on the back of the appliance with a toothbrush. 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. 12.
www.aeg.com • - The appliance does not fill with water properly. Start the appliance again by pressing Start/Pause button. After 5 seconds the door will be unlocked. • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. Please check the door! If the appliance is overloaded, remove some items from the drum and/or keep pressed the door while touching the Start/Pause button until the indicator stops flashing (see the picture below).
ENGLISH Problem The appliance does not fill with water properly. 35 Possible solution • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the inlet hose has no kinks, damages or bends. • Make sure that the connection of the water inlet hose is correct.
www.aeg.com Problem Possible solution The appliance makes an unusual noise and vibrates. • Make sure the levelling of the appliance is correct. Refer to "Installation instruction". • Make sure that the packaging and/or the transit bolts are removed. Refer to "Installation instruction". • Add more laundry in the drum. The load may be too small.
ENGLISH 37 1. Press the Ein /Aus button to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4. Pull the emergency unlock trigger downward once. Pull it downward once again, keep it tensed and, in the meanwhile, open the appliance door. CAUTION! Risk of burns! Make sure that the water temperature is not too high and the laundry is not hot. If necessary, wait until they cool down. CAUTION! Risk of injury! Make sure that the drum is not rotating.
www.aeg.com Programmes Load (kg) Energy Water Approxi- Remainconsump- consump- mate pro- ing moistion (kWh) tion (litre) gramme ture (%)1) duration (minutes) Pflegeleicht 40°C 4 0.72 55 155 35 Feinwäsche 40°C 4 0.60 59 89 35 Wolle/Seide 30°C 2 0.35 58 60 30 Standard 60°C cotton 9 0.53 56 224 52 Standard 60°C cotton 4.5 0.32 41 186 52 Standard 40°C cotton 4.5 0.32 40 183 52 Standard cotton programmes 1) At the end of spin phase. Off Mode (W) 0.
ENGLISH Spin Speed Maximum spin speed 39 1351 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 16. ACCESSORIES 16.1 Available in www.aeg.com/shop or from authorised dealer Only appropriate accessories approved by AEG ensure the safety standards of the appliance. If unapproved parts are used, any claims will be invalidated. 16.2 Fixing plate kit If you install the appliance on a plinth, secure the appliance with the fixing plates.
www.aeg.com 17. PRODUCT INFORMATION SHEET IN REFERENCE TO E.U. REGULATION 1369/2017 Product Information Sheet Trade Mark Model Rated capacity in kg Energy efficiency class AEG L8FS86499, PNC 914550623 9 A+++ Energy consumption in kWh per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partial load, and the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used.
ENGLISH Programme time of the "standard 40°C cotton programme at partial load in minutes 41 183 Duration of the left on mode in minutes 5 Airborne acoustical noise emission in db(A) washing 47 Airborne acoustical noise emission in db(A) spinning 73 Built in appliance Y/N No The information given in the chart above is compliant with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC . 18. ENVIRONMENTAL CONCERNS Recycle materials with the symbol .
www.aeg.
ENGLISH 43
157005163-A-362018 www.aeg.
