L8FS86699 USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................4 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 11 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com 1.2 Allgemeine Sicherheit • • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Überschreiten Sie nicht die maximale Beladungsmenge von 9 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • • • • • • • • • verriegeln und dadurch interne Schäden zu vermeiden. Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk. Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. Halten Sie sich an die mitgelieferte Montageanleitung. Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist.
www.aeg.com Substanzen verschmutzt sind. Die Gummiteile der Waschmaschine könnten beschädigt werden. Waschen Sie solche Textilien mit der Hand vor, bevor Sie sie in die Waschmaschine geben. • Berühren Sie während des Ablaufs eines Programms nicht die Glastür. Das Glas kann sehr heiß werden. 2.5 Innenbeleuchtung WARNUNG! Verletzungsgefahr. • Sichtbare LED-Abstrahlung; vermeiden Sie es, direkt in den Lichtstrahl zu blicken. • Die LED-Lampe dient ausschließlich zur Trommelbeleuchtung.
DEUTSCH 7 1 2 4. Öffnen Sie die Tür und entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel. 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. 8. Reinigen Sie die Unterseite des Geräts und trocknen Sie sie ab. VORSICHT! Verwenden Sie keinen Alkohol, keine Lösungsmittel und keine Chemikalien. 9. Sortieren Sie die verschiedenen Teile des Schallschutzes nach Größe und Position.
www.aeg.com 12. Orientieren Sie sich an der Abbildung. Vergewissern Sie sich, dass die Schallschutzteile fest angebracht sind. x4 15. Lösen Sie die drei Schrauben mit dem mitgelieferten Schraubenschlüssel. A B Bringen Sie die Schallschutzteile bei Raumtemperatur an. 13. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 14. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. 16. Ziehen Sie die KunststoffAbstandshalter heraus. 17.
DEUTSCH 9 WARNUNG! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 45 20 x4 Das Gerät muss einen waagerechten und festen Stand haben. Durch eine korrekte waagrechte Ausrichtung des Geräts werden Vibrationen, Geräusche und ein Wandern des Geräts während des Betriebs vermieden. O O Vergewissern Sie sich, dass sich der Zulaufschlauch nicht in der vertikalen Position befindet. 3. Lösen Sie ggf.
www.aeg.com durch natürliche Alterung auftreten können. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an. A Tritt dieser Fall ein, drehen Sie den Wasserhahn zu und wenden Sie sich an den autorisierten Kundendienst, um den Schlauch zu erneuern. 3.5 Ablassen des Wassers Der Ablaufschlauch muss in einer Höhe nicht unter 60 cm und nicht über 100 cm angebracht werden.
DEUTSCH 11 Stellen Sie sicher, dass der Ablaufschlauch einen Bogen beschreibt, damit keine Partikel aus dem Becken in das Gerät gelangen können. 6. Stecken Sie den Schlauch direkt in ein Abflussrohr in der Zimmerwand und befestigen Sie ihn mit einer Schlauchschelle. 5. Ohne Kunststoffschlauchführung: Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Orientieren Sie sich an der Abbildung. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
www.aeg.com 4.2 Geräteübersicht 1 2 3 10 9 11 4 5 6 12 13 7 8 1 2 3 4 5 6 7 Arbeitsplatte Waschmittelschublade Bedienfeld Türgriff Innenbeleuchtung Typenschild Filter der Ablaufpumpe 8 9 10 11 12 13 Füße für die Ausrichtung des Geräts Ablaufschlauch Anschluss des Zulaufschlauchs Netzkabel Transportschrauben Schlauchhalter 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 Programme Baumwolle Pflegeleicht Feinwäsche Wolle/Seide Dampf ÖKOPower Anti-Allergie 20 min.
DEUTSCH 13 1 Programmwahlschalter 2 Display 3 Sensortaste Energie Sparen (Eco) 7 Sensortaste Extra Spülen (Extra Spülen) 8 Sensortaste Zeitvorwahl (Zeitvorwahl) 4 Sensortaste Zeit Sparen (Zeit Sparen) 9 Sensortaste Plus Dampf (Plus Dampf) 5 Sensortaste Überspringen (Option) 10 Sensortaste Flecken und Vorwäsche (Flecken/Vorw.) 11 Sensortaste Drehzahlreduzierung (U./ Min.
www.aeg.com Die Digitalanzeige zeigt Folgendes an: ). • Programmdauer (z. B. • Zeitvorwahl (z. B. oder ). • Programmende ( ). • Fehlercode (z. B. ). Energiesparanzeigen. Die Anzeige erscheint, wenn ein Baumwollprogramm mit 40 °C oder 60 °C gewählt wird. Hauptwaschgangsanzeige: Blinkt während der Vorwäsche und Hauptwaschphase. Spülphasenanzeige: Blinkt während der Spülphase. Die Anzeige erscheint, wenn die Option Soft Plus eingeschaltet ist. Schleuder- und Abpumpphasenanzeige.
DEUTSCH Da die Standby-Funktion das Gerät automatisch ausschaltet, um in einigen Fällen den Stromverbrauch zu verringern, müssen Sie es möglicherweise erneut einschalten. Siehe Abschnitt Standby im Kapitel „Täglicher Gebrauch“. 6.2 Einführung Die Optionen/Funktionen lassen sich nicht zusammen mit allen Waschprogrammen auswählen. Prüfen Sie die Kompatibilität der Optionen/Funktionen mit den Waschprogrammen in der „Programmübersicht“. Eine Option/Funktion kann eine andere ausschließen.
www.aeg.com • Flecken Wählen Sie diese Option zur Vorbehandlung stark verschmutzter oder stark fleckiger Wäsche mit einem Fleckentferner. Geben Sie den Fleckentferner in das Fach . Der Fleckentferner wird vorgemischt und mit dem Waschmittel erwärmt, um die Wirksamkeit zu verbessern. Mit dieser Option kann sich die Programmdauer verlängern. Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C.
DEUTSCH Wenn Sie ein Baumwollprogramm mit 40 °C oder 60 °C wählen, erscheint im Display die . Das sind Anzeige die standardmäßigen Baumwollprogramme, die hinsichtlich des Energie- und Wasserverbrauchs am effizientesten sind. Alle eingestellten Optionen (mit Ausnahme von Extra Spülen) werden automatisch abgewählt. • Nur Schleudern bei zweimaliger Berührung. Das Gerät lässt die Wasch- und Spülphase aus. • Nur Abpumpen bei dreimaliger Berührung. Das Gerät pumpt nur das Wasser ab.
www.aeg.com Programm Programmbeschreibung Baumwolle Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte. Das Programm Baumwolle bei 60 °C und das Programm Baumwolle bei 40 °C mit der Option sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“.
DEUTSCH Programm Anti-Allergie 20 Min. - 3 kg Outdoor 19 Programmbeschreibung Weiße Baumwollwäsche. Dieses Programm beseitigt Mikroorganismen durch einen Waschgang, bei dem die Temperatur für einige Minuten auf über 60 °C gehalten wird. So werden Keime, Bakterien, Mikroorganismen und Partikel entfernt. Ein zusätzlicher Spülgang sorgt dafür, dass Waschmittelrückstände und Pollen/Allergene beseitigt werden. Auf diese Weise wird die Reinigung effektiver.
www.aeg.com Programmtemperatur, maximale Schleuderdrehzahl und maximale Beladung Programm Standardtemperatur Maximale Schleuder- Maximale BelaTemperaturbereich drehzahl dung Schleuderdrehzahlbereich Baumwolle 40 °C 95 °C – kalt 1600 U/min 1600 U/min – 400 U/min 9 kg Pflegeleicht 40 °C 60 °C – kalt 1200 U/min 1200 U/min – 400 U/min 4 kg Feinwäsche 40 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 4 kg Wolle/Seide 40 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 2 kg - - 1.
DEUTSCH 21 Feinwäsche ÖKOPower Anti-Allergie 20 Min. - 3 kg Outdoor Daunen ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Flecken1) ■ ■ ■ ■ Vorwäsche ■ ■ ■ ■ Extra Spülen ■ ■ ■ Eco 2) ■ ■ ■ Zeit Sparen 3) ■ ■ ■ Nur Spülen ■ ■ ■ ■ ■ ■ ■ ■ ■ Nur Schleudern ■ ■ ■ ■ ■ ■ ■ ■ ■ Nur Abpumpen ■ ■ ■ ■ ■ ■ ■ ■ ■ Zeitvorwahl ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Plus Dampf 1) Soft Plus Dampf Pflegeleicht ■ U./Min.
www.aeg.com 7.2 Woolmark Apparel Care Grün Das Waschprogramm Wolle dieser Maschine wurde von der Firma Woolmark auf das Waschen von Wolltextilien mit der Pflegekennzeichnung „Handwäsche“ getestet und zugelassen, vorausgesetzt, dass die Wäsche gemäß der Anleitung auf dem Kleidungsetikett und gemäß den Angaben des Maschinenherstellers gewaschen wird. Beachten Sie die Trocken- und Waschanleitung auf dem Kleidungsetikett.
DEUTSCH Sind die akustischen Signale ausgeschaltet, ertönen sie nur noch dann, wenn eine Störung vorliegt. 9.3 Extra Spülen dauerhaft einschalten Wenn Sie diese Option wählen, ist bei Auswahl eines kompatiblen Programms die Funktion Extra Spülen stets eingeschaltet. • Berühren Sie zum Ein-/Ausschalten dieser Option die Tasten Extra Spülen und Option gleichzeitig, bis die zugehörige Anzeige aufleuchtet/ erlischt. Diese Option fügt dem Programm zwei Spülgänge hinzu und das Display zeigt 23 9.
www.aeg.com Optionen hinzuzufügen und/oder die Zeitvorwahl einzustellen. Im Display erscheint das Symbol der eingestellten Option und/oder die Ziffernanzeige zeigt die Zeitvorwahl an. 10.4 Einfüllen der Wäsche 1. Öffnen Sie die Tür des Geräts. Im Display erscheint . 2. Schütteln Sie jedes Wäschestück leicht aus, bevor Sie es in die Trommel füllen. Geben Sie jedes Wäschestück einzeln in die Trommel.
DEUTSCH Fach für den Fleckentferner. Klappe für Waschpulver oder Flüssigwaschmittel. Halten Sie sich immer an die Anweisungen auf der Verpackung der Waschmittel. Wir empfehlen Ihnen aber, die Höchstmenge ( ) nicht zu überschreiten. Diese Menge garantiert die besten Waschergebnisse. 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. Entfernen Sie nach dem Waschgang bei Bedarf Waschmittelreste aus der Waschmittelschublade. 10.6 Überprüfen Sie die Position der Klappe 1.
www.aeg.com Abbrechen der Zeitvorwahl nach dem Start des Countdowns Abbrechen der Zeitvorwahl: Achten Sie darauf, dass die Klappe beim Schließen der Waschmittelschublade nicht blockiert. 10.7 Starten eines Programms Berühren Sie die Taste Start/Pause, um das Programm zu starten. Die zugehörige Anzeige hört auf zu blinken und leuchtet konstant. Im Display blinkt die Anzeige der Programmphase und die Waschmittelprozent-Anzeige erlischt. Das Programm startet, die Tür ist verriegelt.
DEUTSCH Die ProSense Erkennung wird nur bei vollständigen Waschprogrammen ausgeführt (wenn keine Phase übersprungen wird). 27 2. Ändern Sie die Optionen. Die im Display angezeigten Informationen ändern sich entsprechend. 3. Berühren Sie die Taste Start/Pause erneut. Das Waschprogramm wird fortgesetzt. 10.10 Programmphasenanzeigen 10.12 Abbrechen eines laufenden Programms Beim Programmstart blinkt die Anzeige der laufenden Phase und die anderen Phasenanzeigen leuchten konstant. 1.
www.aeg.com Es ertönt ein Signalton (falls er aktiviert ist). • Sie müssen das Wasser abpumpen, um die Tür öffnen zu können: Im Display leuchten alle Waschphasenanzeigen konstant und im 1. Berühren Sie bei Bedarf die Taste U./ Min., um die vom Gerät vorgeschlagene Schleuderdrehzahl zu verringern. 2. Berühren Sie die Taste Start/Pause: Zeitbereich erscheint . Die Kontrolllampe der Taste Start/Pause erlischt. Die Tür wird entriegelt und die Anzeige erlischt. 1.
DEUTSCH 29 Haben Sie ein Programm oder eine Option gewählt, das/die mit Wasser in der Trommel endet, schaltet die Standby-Funktion das Gerät nicht aus, um Sie daran zu erinnern, dass das Wasser abgepumpt werden muss. 11. TIPPS UND HINWEISE WARNUNG! Siehe Kapitel Sicherheitshinweise. 11.1 Beladung • Teilen Sie die Wäsche auf, und zwar in: kochwäsche, buntwäsche, synthetik, feinwäsche und wolle. • Halten Sie sich an die Anweisungen auf den Pflegeetiketten.
www.aeg.com • Mischen Sie nicht verschiedene Waschmittel. • Verwenden Sie der Umwelt zuliebe nicht mehr als die empfohlene Waschmittelmenge. • Halten Sie sich an die Anweisungen auf der Verpackung der Wasch- und Pflegemittel und überschreiten Sie nicht die Höchstmenge ( ). • Verwenden Sie die empfohlenen Waschmittel für Art und Farbe des Gewebes, Programmtemperatur und Verschmutzungsgrad. 11.4 Umwelttipps • Stellen Sie zum Waschen normal verschmutzter Wäsche ein Programm ohne Vorwäsche ein.
DEUTSCH Flusenansammlungen und Bakterienbildung in der Trommel und im Bottich führen. So können unangenehme Gerüche und Schimmel entstehen. Um diese Ablagerungen zu entfernen und das Innere der Maschine zu entkeimen, führen Sie regelmäßig (mindestens einmal im Monat) einen Waschgang zur Pflege der Maschine durch. 1. Nehmen Sie die Wäsche aus der Trommel. 2. Starten Sie ein Programm für Baumwolle mit der maximalen Temperatur und einer kleinen Menge Waschpulver. 31 12.
www.aeg.com WARNUNG! • Entfernen Sie das Sieb nicht, während das Gerät in Betrieb ist. • Reinigen Sie die Ablaufpumpe nicht, wenn das Wasser im Gerät heiß ist. Warten Sie, bis das Wasser abkühlt. 4. Setzen Sie die Waschmittelschublade in die Führungsschienen ein und schließen Sie sie. Starten Sie das Spülprogramm ohne Wäsche in der Trommel. Gehen Sie zum Reinigen der Pumpe folgendermaßen vor: 1. Öffnen Sie die Pumpenabdeckung. 2 1 12.
DEUTSCH 33 10. Reinigen Sie das Sieb unter fließendem Wasser. 5. Wenn der Behälter voll ist, drehen Sie das Sieb zurück und leeren Sie den Behälter. 6. Wiederholen Sie die Schritte 4 und 5, bis kein Wasser mehr herausfließt. 7. Drehen Sie das Sieb gegen den Uhrzeigersinn, um es zu entfernen. 11. Setzen Sie das Sieb wieder in die dafür vorgesehenen Führungen ein und drehen Sie es im Uhrzeigersinn. Achten Sie darauf, dass Sie das Sieb richtig fest anziehen, um Wasserlecks zu vermeiden. 1 2 12.
www.aeg.com 12.8 Reinigen des Siebs des Zulaufschlauchs und Ventils Es wird empfohlen, das Sieb des Zulaufschlauchs und das des Ventils gelegentlich zu reinigen, um Ablagerungen zu entfernen, die sich mit der Zeit ansammeln. 4. Wenn Sie den Schlauch wieder an der Geräterückseite anbringen, drehen Sie ihn je nach Position des Wasserhahns nach rechts oder links (nicht in die vertikale Position). 1. Schrauben Sie den Zulaufschlauch vom Wasserhahn ab und reinigen Sie das Sieb. 1 45° 20° 2 12.
DEUTSCH 35 WARNUNG! Stellen Sie sicher, dass die Temperatur über 0 °C liegt, bevor Sie das Gerät wieder einschalten. Der Hersteller ist nicht für Schäden verantwortlich, die auf zu niedrige Temperaturen zurückzuführen sind. 13. FEHLERSUCHE WARNUNG! Siehe Kapitel Sicherheitshinweise. 13.1 Einführung Das Gerät startet nicht oder bleibt während des Betriebs stehen. Versuchen Sie zunächst, selbst eine Lösung für das Problem zu finden (siehe Tabelle).
www.aeg.com 13.2 Mögliche Störungen Störung Das Programm startet nicht. Mögliche Abhilfe • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. • Stellen Sie sicher, dass Start/Pause berührt wurde. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab oder warten Sie, bis sie abgelaufen ist.
DEUTSCH 37 Störung Mögliche Abhilfe Es befindet sich Wasser auf dem Boden. • Vergewissern Sie sich, dass alle Wasseranschlüsse vollkommen dicht sind, sodass kein Wasser austreten kann. • Vergewissern Sie sich, dass der Wasserzulauf- und -ablaufschlauch nicht beschädigt sind. • Verwenden Sie ein geeignetes Waschmittel in der richtigen Menge. Die Tür des Geräts lässt sich nicht öffnen. • Prüfen Sie, ob das gewählte Waschprogramm mit Wasser in der Trommel endet.
www.aeg.com Störung Mögliche Abhilfe Die Trommel ist leer und im Display wird angezeigt, dass sich Wäsche darin befindet. • Schalten Sie das Gerät mit der Taste Ein/Aus aus und wieder ein, um das Leergewicht einzustellen. Die Trommel ist voll, im Display wird jedoch 0,0 kg angezeigt. • Sie haben die Wäsche eingefüllt, bevor das Gerät eingeschaltet wurde. Drücken Sie die Taste Ein/Aus, um das Gerät auszuschalten. • Leeren Sie die Trommel und führen Sie die notwendigen Schritte aus.
DEUTSCH 39 5. Nehmen Sie die Wäsche heraus und schließen Sie die Gerätetür. 6. Schließen Sie die Filterklappe. 14. VERBRAUCHSWERTE Die angegebenen Werte wurden unter Laborbedingungen gemäß den einschlägigen Normen gemessen. Folgende Faktoren können diese Werte verändern: Wäscheart und -menge sowie Raumtemperatur. Der Wasserdruck, die Versorgungsspannung und die Temperatur des einlaufenden Wassers können sich auch auf die Dauer des Waschprogramms auswirken.
www.aeg.com Programme Beladung (kg) Standardprogramm Baumwolle 60 °C Standardprogramm Baumwolle 40 °C EnergieWasserUngefähverbrauch verbrauch re Pro(kWh) (Liter) grammdauer (in Minuten) Restfeuchte (%)1) 4.5 0.37 39 191 44 4.5 0.36 40 190 44 1) Am Ende der Schleuderphase. Aus-Zustand (W) Ein-Zustand (W) 0.30 0.30 Die in der Tabelle oben enthaltenen Informationen erfüllen die Verordnung (EU) 1015/2010 der Kommission zur Durchführung der Richtlinie 2009/125/EG. 15.
DEUTSCH 41 16. ZUBEHÖR 16.1 Verfügbar bei www.aeg.com/shop oder einem autorisierten Händler Nur mit geeignetem, von AEG zugelassenem Zubehör können die Sicherheitsstandards des Geräts gewährleistet werden. Werden nicht zugelassene Teile verwendet, erlischt jeglicher Gewährleistungsanspruch. 16.2 Satz Fixierplatten Wenn Sie das Gerät auf einem Sockel aufstellen, befestigen Sie es mithilfe der Fixierplatten. Lesen Sie die mit dem Zubehör gelieferte Gebrauchsanleitung sorgfältig durch.
www.aeg.com 17. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte. Entsorgen Sie * Geräte mit diesem Symbol nicht mit dem Hausmüll. Bringen Sie das Gerät zu Ihrer örtlichen Sammelstelle oder wenden Sie sich an Ihr Gemeindeamt.
DEUTSCH 43
157004172-A-152017 www.aeg.