L8FS9413CM USER MANUAL FR Notice d'utilisation Lave-linge
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ.................................................................................3 2. CONSIGNES DE SÉCURITÉ........................................................................................4 3. INSTALLATION............................................................................................................6 4. DESCRIPTION DE L'APPAREIL.................................................................................10 5.
FRANÇAIS 1. 3 INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • La pression de l'eau en service au niveau du point d'entrée en provenance de l'arrivée d'eau doit être comprise entre 0,5 bar (0,05 MPa) et 8 bar (0,8 MPa). Les orifices d'aération situés à la base (si présents) ne doivent pas être obstrués par de la moquette, un tapis, ou tout type de revêtement de sol. L'appareil doit être raccordé à l'arrivée d'eau à l'aide des tuyaux neufs fournis, ou d'autres tuyaux neufs fournis par le service après-vente agréé.
FRANÇAIS service après-vente agréé pour connaître les accessoires disponibles. 2.2 Branchement électrique • L'appareil doit être relié à la terre. • Utilisez toujours une prise de courant de sécurité correctement installée. • Vérifiez que les données électriques figurant sur la plaque signalétique correspondent à celles de votre réseau. Si ce n'est pas le cas, contactez un électricien. • N'utilisez pas d'adaptateurs multiprises ni de rallonges.
www.aeg.com • Retirez le dispositif de verrouillage du hublot pour empêcher les enfants et les animaux de s'enfermer dans le tambour. • Jetez l'appareil en vous conformant aux exigences locales relatives à la mise au rebut des Déchets d'équipements électriques et électroniques (DEEE). 3. INSTALLATION AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 3.1 Déballage AVERTISSEMENT! Retirez l'intégralité de l'emballage et les boulons de transport avant d'installer l'appareil.
FRANÇAIS x4 1 7 A 2 8. Nettoyez soigneusement et séchez le bas de l'appareil. ATTENTION! N'utilisez pas d'alcool, de solvants ni de produits chimiques. 9. Veillez à identifier la taille et l'emplacement des différents isolants acoustiques. Reportez-vous à l'illustration : B Fixez les isolants acoustiques à température ambiante. 13. Remettez l'appareil en position verticale. 14. Retirez le câble d'alimentation électrique et le tuyau de vidange de leurs supports.
www.aeg.com 16. Retirez les entretoises en plastique. 17. Placez les caches en plastique, fournis dans le sachet du manuel d'utilisation, dans les trous. x4 L'appareil doit être de niveau et stable. Une mise de niveau correcte évite les vibrations, le bruit ou des déplacements de l'appareil au cours de son fonctionnement. Nous vous recommandons de conserver l'emballage et les boulons de transport en vue d'un éventuel déplacement de l'appareil. 3.2 Positionnement et mise de niveau 1.
FRANÇAIS 9 La partie rouge dans la fenêtre « A » témoigne de ce dysfonctionnement. 45 20 O O Assurez-vous que le tuyau d'arrivée d'eau n'est pas en position verticale. 3. Si nécessaire, desserrez la bague de serrage pour bien le positionner. 4. Raccordez le tuyau d'arrivée d'eau à un robinet d'eau froide fileté (3/4 pouce). ATTENTION! Assurez-vous que les raccords ne fuient pas. N'utilisez pas de rallonge si le tuyau d'alimentation est trop court.
www.aeg.com Vérifiez que l'extrémité du tuyau de vidange n'est pas plongée dans l'eau. Il pourrait y avoir un reflux d'eau sale dans l'appareil. 3. À une conduite fixe dotée d'une ventilation spéciale : insérez directement le tuyau dans la conduite d'évacuation. Reportezvous à l'illustration. L'extrémité du tuyau de vidange doit être ventilée en permanence, c'est-à-dire que le diamètre interne du conduit d’évacuation (minimum 38 mm - min.
FRANÇAIS tissus grâce aux différentes phases de pré-mélange qui dissolvent d'abord le produit de lavage puis l'assouplissant dans l'eau avant de les libérer dans le linge. Ainsi, chaque fibre est traitée et lavée. • Grâce aux capteurs de poids, l'appareil peut détecter le poids de votre charge et vous indiquer la quantité de lessive nécessaire pour obtenir les meilleurs résultats sans gaspiller.
www.aeg.com 5. BANDEAU DE COMMANDE 5.1 Description du bandeau de commande 3 2 1 Program Eco Cottons Synthetics Delicates Wool / Silk Steam OKOPower Anti-Allergy 20 min. - 3 kg Outdoor Jeans Only Rinse Only Spin 5 Only Drain Spin Temp.
FRANÇAIS Voyant de poids du linge. Le voyant clignote lors de l'estimation de la charge de linge (consultez le paragraphe « Détection de la charge PROSENSE »). Voyant de charge maximale. Il clignote lorsque la charge de linge dépasse la charge maximale prévue pour le programme sélectionné. Voyant de la quantité de produit de lavage : la valeur indique le pourcentage de lessive nécessaire. Indicateur Départ différé. Voyant Hublot verrouillé.
www.aeg.com Voyant Extra silence. Voyant de prélavage. Voyant Détachage. Voyant Rinçage plus. 6. SÉLECTEUR ET TOUCHES 6.1 On/Off Appuyez sur cette touche pendant quelques secondes pour allumer et éteindre l'appareil. Deux différents signaux sonores retentissent lorsque vous allumez ou éteignez l'appareil. Appuyez à plusieurs reprises sur cette touche jusqu'à ce que la température souhaitée s'affiche. Lorsque et s'affichent, l'appareil ne chauffe pas l'eau. 6.
FRANÇAIS termine avec de l'eau dans le tambour. Cela réduit le froissage du linge. Ce programme étant très silencieux, il peut être utilisé de façon optimale la nuit, aux heures creuses, lorsque les tarifs de l'électricité sont plus bas. Certains programmes utilisent plus d'eau lors du rinçage. L'indicateur s'allume. Le hublot reste verrouillé. Le tambour tourne régulièrement pour éviter que le linge ne se froisse. Vous devez vidanger l'eau pour pouvoir ouvrir le hublot.
www.aeg.com mouvements anti-froissage s'arrêtent et le hublot se déverrouille. Une petite quantité de linge aide à obtenir de meilleurs résultats. 6.8 Eco Sélectionnez cette option pour le linge légèrement ou normalement sale, lavé à 30 °C ou plus. L'appareil diminue la température et rallonge la durée du lavage pour obtenir un lavage efficace tout en économisant de l'énergie. L'indicateur s'allume.
FRANÇAIS 17 7. PROGRAMMES 7.1 Tableau des programmes Programmes de lavage Programme Description du programme Programmes de lavage Cottons Coton blanc et couleurs. Normalement sale ou légèrement sale. Programme Éco. Ce programme à 60 °C avec une charge de 9 kg est le programme de référence pour les données de l'étiquette énergétique, conformément à la norme CEE 95/12 de la commission européenne et mesuré conformément à la norme EN 60456/2005. Synthetics Articles en textiles synthétiques ou mixtes.
www.aeg.com Programme Anti-Allergy 20 min. - 3 kg Outdoor Description du programme Articles en coton blanc. Ce programme élimine les micro-organismes grâce à une phase de lavage à une température maintenue à plus de 60 °C pendant quelques minutes. Cela permet d'éliminer les germes, bactéries, micro-organismes et particules. Pour garantir une parfaite élimination des résidus de détergent et des particules de pollen ou autres allergènes sur les textiles, effectuez une phase de rinçage supplémentaire.
FRANÇAIS 19 Température du programme, vitesse d'essorage maximale et charge maximale Programme Température par défaut Plage de températures Vitesse d'essorage maximale Plage de vitesses d'essorage Cottons 40 °C 95 °C - Froid 1400 tr/min 1400 tr/min 400 tr/min 9 kg Synthetics 40 °C 60 °C - Froid 1200 tr/min 1200 tr/min 400 tr/min 4 kg Delicates 40 °C 40 °C - Froid 1200 tr/min 1200 tr/min 400 tr/min 4 kg Wool/Silk 40 °C 40 °C - Froid 1200 tr/min 1200 tr/min 400 tr/min 2 kg - - 1.
www.aeg.com 20 min.
FRANÇAIS 7.2 Woolmark Apparel Care Vert 21 le lavage des vêtements en laine portant une étiquette « lavage à la main », sous réserve que les vêtements soient lavés conformément aux instructions mentionnées par le fabricant de ce lavelinge. Respectez les instructions de séchage figurant sur l'étiquette des vêtements et toutes les autres instructions concernant le linge. M1361 Au Royaume-Uni, en Irlande, à Hong Kong ainsi qu'en Inde, le symbole Woolmark est une marque de certification.
www.aeg.com Pour désactiver/activer les signaux sonores, appuyez simultanément sur les touches Rinse+ et Delay Start pendant 6 secondes. Si vous désactivez les signaux sonores, ils continueront à retentir si l'appareil présente une anomalie. Cette option ajoute deux rinçages et s'affiche. 9.4 Soft Plus Sélectionnez l'option Soft Plus pour optimiser la distribution d'assouplissant et rendre le linge plus doux. Il est recommandé lorsque vous utilisez de l'assouplissant. 9.
FRANÇAIS 23 Le symbole de l'option choisie s'affiche et le chiffre indique la durée du départ différé. 10.4 Chargement du linge 1. Ouvrez le hublot de l'appareil. L'affichage indique . 2. Mettez le linge dans le tambour, un article à la fois. Dépliez les articles le plus possible. Sur l'affichage, le poids du linge est mis à jour par paliers de 0,5 kg et la durée du programme est adaptée en fonction. Le poids est indicatif et change selon le type de linge.
www.aeg.com Compartiment réservé au détachant. Volet pour produit de lavage en poudre ou liquide. Suivez toujours les instructions imprimées sur l'emballage des produits de lavage, mais nous vous recommandons de ne pas dépasser le niveau maximal indiqué ( ). Cette quantité vous garantira les meilleurs résultats de lavage. 4. Pour utiliser de la lessive liquide, tournez le volet vers le bas. Après un cycle de lavage, si nécessaire, éliminez les résidus de lessive du distributeur de produit de lavage.
FRANÇAIS 25 Annulation du départ différé au cours du décompte Pour annuler le départ différé : Assurez-vous que le volet ne bloque pas la fermeture du tiroir. 10.7 Départ d'un programme Appuyez sur la touche Start/Pause pour lancer le programme. Le voyant correspondant cesse de clignoter et reste fixe. Sur l'affichage, le voyant de la phase en cours commence à clignoter et l'indicateur du pourcentage de détergent s'éteint. Le programme démarre et le hublot est verrouillé. L'indicateur s'allume.
www.aeg.com Le voyant correspondant clignote. 2. Modifiez les options. Les informations données sur l'affichage changent en conséquence. 3. Appuyez à nouveau sur la touche Start/Pause. Le programme de lavage se poursuit. La détection ProSense est uniquement effectuée pour les programmes de lavage complets (sans aucune phase supprimée). 10.10 Voyants de phase du programme Lorsque le programme démarre, le voyant de la phase en cours clignote et les autres voyants de phase sont fixes. Par ex.
FRANÇAIS 10.14 Fin du programme Lorsque le programme est terminé, l'appareil s'éteint automatiquement. Les signaux sonores retentissent (s'ils sont activés). Sur l'affichage, tous les voyants de la phase de lavage sont fixes et l'affichage du temps indique . Le voyant de la touche Start/Pause s'éteint. Le hublot se déverrouille et le voyant s'éteint. 1. Appuyez sur la touche On/Off pour éteindre l'appareil.
www.aeg.com 11. CONSEILS AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 11.1 Chargement du linge • Séparez le linge en fonction des articles : blancs, de couleurs, synthétiques, délicats et en laine. • Respectez les instructions de lavage qui figurent sur les étiquettes des vêtements. • Ne lavez pas les articles blancs et de couleur ensemble. • Certains articles de couleurs peuvent déteindre lors des premiers lavages. Il est recommandé de les laver séparément les premières fois.
FRANÇAIS • Commencez toujours un programme de lavage avec une charge de linge maximale. • Pour prétraiter les taches, vous pouvez utiliser un détachant si vous sélectionnez un programme à basse température. • Pour utiliser la bonne quantité de produit de lavage, vérifiez la dureté de l'eau de votre système domestique. Reportez-vous au chapitre « Dureté de l'eau ». 29 recommandé d'utiliser un adoucisseur d'eau pour lave-linge.
www.aeg.com 12.4 Joint du hublot 1 2 Examinez régulièrement le joint et enlevez tous les objets situés à l'intérieur. 12.5 Nettoyage du tambour Examinez régulièrement le tambour pour éviter le dépôt de particules de rouille. Pour un nettoyage complet : 1. Nettoyez le tambour à l'aide d'un produit spécial pour l'acier inoxydable. 2.
FRANÇAIS 31 2 1 12.7 Nettoyage de la pompe de vidange AVERTISSEMENT! Débranchez le cordon d'alimentation de l'appareil de la prise de courant. Vérifiez régulièrement le filtre de la pompe de vidange pour vérifier sa propreté. Nettoyez la pompe de vidange dans le cas où : • L'appareil ne vidange pas. • Le tambour ne tourne pas. • L'appareil fait un bruit inhabituel, car la pompe de vidange est obstruée. • L'écran affiche le code d’alarme 2.
www.aeg.com 2 1 7. Fermez la conduite de vidange et tournez le filtre dans le sens antihoraire pour le retirer. 11. Replacez le filtre dans les guides prévus en le tournant dans le sens horaire. Assurez-vous de visser correctement le filtre pour empêcher les fuites. 2 2 1 1 8. Si nécessaire, retirez les peluches et les débris de la cavité du filtre. 9. Assurez-vous que la turbine de la pompe tourne librement. Si ce n'est pas le cas, contactez votre service après-vente agréé. 12.
FRANÇAIS 12.8 Nettoyage du tuyau d'arrivée d'eau et du filtre de la vanne Il est recommandé de nettoyer occasionnellement les deux filtres du tuyau d'arrivée d'eau et la valve pour éliminer les dépôts accumulés avec le temps : 33 4. Lorsque vous rebranchez le tuyau à l'arrière de l'appareil, tournez-le vers la gauche ou la droite (et non en position verticale) en fonction de la position du robinet. 1. Retirez le tuyau d'arrivée d'eau du robinet et nettoyez le filtre. 1 45° 20° 2 12.
www.aeg.com AVERTISSEMENT! Assurez-vous que la température est supérieure à 0 °C avant d'utiliser à nouveau l'appareil. Le fabricant ne pourra être tenu pour responsable en cas de dommages dus aux basses températures. 13. EN CAS D'ANOMALIE DE FONCTIONNEMENT AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 13.1 Introduction L'appareil ne démarre pas ou s'arrête en cours de programme. Dans un premier temps, essayez de trouver une solution au problème (reportez-vous au tableau).
FRANÇAIS 35 13.2 Pannes possibles Problème Solution possible Le programme ne démarre pas. Assurez-vous que la fiche du câble d'alimentation est bien insérée dans la prise de courant. Vérifiez que le hublot de l'appareil est fermé. Assurez-vous qu'aucun fusible n'est grillé dans la boîte à fusibles. Vérifiez que vous avez bien appuyé sur la touche Start/Pause. Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte.
www.aeg.com Problème Solution possible Sélectionnez le programme de vidange si vous avez choisi une option se terminant avec de l'eau dans la cuve. La phase d'essorage n'a Sélectionnez le programme d'essorage. pas lieu ou le cycle de lavage dure plus longtemps que d'habitude. Assurez-vous que le filtre de vidange n'est pas obstrué. Nettoyez le filtre si nécessaire. Reportez-vous au chapitre « Entretien et nettoyage ».
FRANÇAIS Problème 37 Solution possible Utilisez des produits spéciaux pour enlever les taches tenaces avant de laver le linge. Veillez à sélectionner la bonne température. Réduisez la charge de linge. Il y a trop de mousse Réduisez la quantité de produit de lavage. dans le tambour au cours du cycle de lavage. À la fin du cycle de lavage, il y a des résidus de produit de lavage dans le distributeur de produit de lavage.
www.aeg.com 4. Maintenez le dispositif de déverrouillage d'urgence en le tirant vers le bas et ouvrez le hublot simultanément. Assurez-vous que le niveau de l'eau à l'intérieur du tambour n'est pas trop élevé. Effectuez une vidange d'urgence si nécessaire (reportez-vous à la section « Vidange d'urgence » au chapitre « Entretien et nettoyage »). Pour ouvrir le hublot, procédez comme suit : 1. Appuyez sur la touche On/Off pour éteindre l'appareil. 2.
FRANÇAIS Mode « Éteint » (W) Mode « Veille » (W) 0,30 0,30 39 Les informations fournies dans le tableau ci-dessus sont conformes à la directive d'application 1015/2010 de la réglementation 2009/125/CE de la commission européenne. 15.
www.aeg.com Lisez attentivement la notice fournie avec l'accessoire. Lisez attentivement les notices fournies avec l'appareil et avec l'accessoire. AVERTISSEMENT! N'installez pas le sèche-linge sous le lave-linge. 16.4 Kit de superposition 16.5 Socle à tiroir Le sèche-linge ne peut-être superposé au-dessus du lave-linge qu'en utilisant le kit de superposition adapté, fabriqué et agréé par AEG. Pour surélever votre appareil et faciliter le chargement et le déchargement du linge.
FRANÇAIS 41
www.aeg.
FRANÇAIS 43
157007830-A-452016 www.aeg.