L8WED164C USER MANUAL FR Notice d'utilisation Lavante-séchante
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ.................................................................................3 2. CONSIGNES DE SÉCURITÉ........................................................................................6 3. INSTALLATION............................................................................................................8 4. DESCRIPTION DE L'APPAREIL.................................................................................12 5.
FRANÇAIS 3 Sous réserve de modifications. 1. INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • Les enfants ne doivent pas nettoyer ni entreprendre une opération de maintenance sur l'appareil sans surveillance. 1.2 Sécurité générale • • • • • • • • • Ne modifiez pas les caractéristiques de cet appareil.
FRANÇAIS • • • • • • • • • • 5 des appareils brûlant du gaz ou d'autres combustibles. La pression de l'eau en service au niveau du point d'entrée en provenance de l'arrivée d'eau doit être comprise entre 0,5 bar (0,05 MPa) et 8 bar (0,8 MPa). Respectez la charge maximale de 10 kg (reportez-vous au chapitre « Tableau des programmes »). L'appareil doit être raccordé à l'arrivée d'eau à l'aide des tuyaux neufs fournis, ou d'autres tuyaux neufs fournis par le service après-vente agréé.
www.aeg.com • • • • • • • Les assouplissants ou autres produits similaires doivent être utilisés conformément aux instructions de leur fabricant. Retirez des vêtements tous les objets pouvant provoquer un incendie comme les briquets ou les allumettes. N'arrêtez jamais la lavante-séchante avant la fin du cycle de séchage à moins de sortir immédiatement tout le linge et de le déplier séparément pour dissiper la chaleur résiduelle.
FRANÇAIS • N'installez pas l'appareil dans un endroit où il ne pourrait pas être complètement ouvert. • Réglez les pieds pour laisser un espace suffisant entre l'appareil et le sol. • Une fois l'appareil installé à son emplacement permanent, vérifiez qu'il est bien de niveau à l'aide d'un niveau à bulle. S'il n'est pas de niveau, réglez les pieds jusqu'à ce qu'il le soit. 2.2 Branchement électrique AVERTISSEMENT! Risque d'incendie ou d'électrocution. • L'appareil doit être relié à la terre.
www.aeg.com 2.6 Mise au rebut • Débranchez l'appareil de l'alimentation électrique et de l'arrivée d'eau. • Coupez le câble d'alimentation au ras de l'appareil et mettez-le au rebut. • Retirez le dispositif de verrouillage du hublot pour empêcher les enfants et les animaux de s'enfermer dans le tambour. • Jetez l'appareil en vous conformant aux exigences locales relatives à la mise au rebut des Déchets d'équipements électriques et électroniques (DEEE). 3.
FRANÇAIS 7. Retirez la protection en polystyrène en bas de l'appareil. 9 10. Dévissez les trois boulons à l'aide de la clé fournie avec l'appareil. 1 2 8. Remettez l'appareil en position verticale. 9. Retirez le câble d'alimentation électrique et le tuyau de vidange de leurs supports. Il est possible de voir de l'eau s'écouler du tuyau d'évacuation. Cette eau provient des tests effectués sur l'appareil en usine. 11. Retirez les entretoises en plastique. 12.
www.aeg.com Assurez-vous que la circulation de l'air sous l'appareil ne soit pas entravée par des tapis. Veillez à ce que l'appareil ne touche pas le mur ni d'autres éléments. 2. Desserrez ou serrez les pieds jusqu'à ce que l'appareil soit de niveau. AVERTISSEMENT! Ne placez ni carton, ni bois, ni autre matériau sous les pieds de l'appareil pour le mettre de niveau. 3.3 Tuyau d'arrivée d'eau 1. Raccordez le tuyau d'arrivée d'eau à l'arrière de l'appareil. 2.
FRANÇAIS 11 ATTENTION! Assurez-vous que les raccords ne fuient pas. N'utilisez pas de rallonge si le tuyau d'alimentation est trop court. Contactez le service après-vente pour remplacer le tuyau d'alimentation. 3.4 Dispositif d'arrêt de l'eau Le tuyau d'arrivée d'eau est équipé d'un dispositif de protection contre les dégâts des eaux. Si le tuyau devait se détériorer à cause d'une usure naturelle, ce dispositif bloquerait l'arrivée d'eau à l'appareil. 2.
www.aeg.com L'extrémité du tuyau de vidange doit être ventilée en permanence, c'est-à-dire que le diamètre interne du conduit d’évacuation (minimum 38 mm - min. 1,5 po) doit être supérieur au diamètre externe du tuyau de vidange. 4. Si l'extrémité du tuyau de vidange ressemble à l'image, vous pouvez l'insérer directement dans la conduite fixe. Veillez à ce que le tuyau de vidange fasse une boucle afin d'éviter que des particules passent de l'évier à l'appareil. 6.
FRANÇAIS 1 2 3 4 5 6 7 Plan de travail Distributeur de produit de lavage Bandeau de commande Poignée d'ouverture du hublot Plaque signalétique (située à l'arrière) Filtre de la pompe de vidange Pieds pour la mise de niveau de l'appareil 8 9 10 11 12 13 Tuyau de vidange Raccord du tuyau d'arrivée d'eau Câble d'alimentation électrique Boulons de transport Support du tuyau 5. BANDEAU DE COMMANDE 5.
www.aeg.com 5.2 Affichage MIX Voyant de poids du linge. Le voyant clignote lors de l'estimation de la charge de linge (consultez le paragraphe « Détection de la charge PROSENSE »). Voyant de charge maximale. Il clignote lorsque la charge de linge dépasse la charge maximale prévue pour le programme sélectionné. Voyant de la quantité de produit de lavage : la valeur indique le pourcentage de lessive nécessaire. Voyant Sécurité enfants. Indicateur du temps de séchage. Voyant Hublot verrouillé.
FRANÇAIS Voyant de phase Vapeur. Voyant de phase de séchage. Indicateur Prêt à repasser. Indicateur Prêt à ranger Indicateur Séchage +. Indicateur de température. Le voyant tionnez un lavage à froid. apparaît lorsque vous sélec- Indicateur de vitesse d'essorage. Voyant Arrêt cuve pleine. Voyant Extra silence. Voyant de prélavage. Voyant Détachage. ÉCO Voyants d'économies d'énergie. Ils apparaissent lorsque vous sélectionnez le programme Coton Eco. Indicateur Départ différé. 6. MANETTES ET TOUCHES 6.
www.aeg.com 6.3 Température Lorsque vous sélectionnez un programme de lavage, l'appareil propose automatiquement une température par défaut. Appuyez à plusieurs reprises sur cette touche jusqu'à ce que la température souhaitée s'affiche. et s'affichent, l'appareil Lorsque ne chauffe pas l'eau. 6.4 Options tarifs de l'électricité sont plus bas. Certains programmes utilisent plus d'eau lors du rinçage. s'allume. L'indicateur Le hublot reste verrouillé.
FRANÇAIS Ces deux options ne peuvent pas être sélectionnées ensemble. 6.6 Départ Différé Cette option vous permet de différer le départ du programme à un moment qui vous convient mieux. 17 Cette option peut rallonger la durée du programme. En appuyant sur une touche, les mouvements anti-froissage s'arrêtent et le hublot se déverrouille. 6.9 Minuterie Appuyez à plusieurs reprises sur la touche pour sélectionner le délai souhaité.
www.aeg.com 6.12 Départ/Pause Appuyez sur la touche Départ/Pause pour démarrer l'appareil, le mettre en pause ou interrompre un programme en cours. 7. PROGRAMMES 7.1 Tableau des programmes Programme Description du programme Programmes de lavage Blanc/Couleurs Coton Eco Synthétiques Délicats Coton blanc et couleurs. Normalement, très et légèrement sales. Coton blanc et couleurs. Normalement, très et légèrement sales. Programme Coton éco.
FRANÇAIS Programme Description du programme Propre&Sec ÖKOPower Textiles mixtes (articles en coton et synthétiques). Un programme complet pour laver et sécher 5 kg de vêtements en seulement 4 heures. Le voyant 19 s'affiche également. Programme vapeur Programmes vapeur2) Vapuer La vapeur peut être utilisée sur du linge sec, lavé ou porté une seule fois. Ces programmes peuvent atténuer les plis et les odeurs et rendre votre linge plus doux. N'utilisez aucun produit de lavage.
www.aeg.
FRANÇAIS 21 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Essorage/Vidange ■ Rinçage ■ Vapuer Propre&Sec ÖKOPower Laine/Lavage à la main Outdoor Extra Silence Délicats Arrêt cuve pleine Synthétiques Options Coton Eco Options Blanc/Couleurs Programme Compatibilité des options avec les programmes ■ ■ ■ ■1) Sans essorage Rinçage Plus Prélavage Tache2) Départ Différé Gain de temps3) Antifroissage Minuterie ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Niveau séchage Essorage/Vidange Rinçage Vapuer Propre&Sec ÖKOPower Outdoor Laine/Lavage à la main ■4) Délicats ■ Synthétiques Coton Eco Options Blanc/Couleurs www.aeg.com Programme 22 1) Si vous sélectionnez l'option Sans essorage, l'appareil vidange uniquement l'eau. 2) Cette option n'est pas disponible avec des températures de lavage inférieures à 40 °C. 3) Si vous sélectionnez la durée la plus courte, nous vous recommandons de réduire la charge de linge.
FRANÇAIS Degré de séchage Prêt à Ranger1) Pour les articles à ranger directement Type de textile Charge Coton et lin (peignoirs, serviettes de bain, etc.
www.aeg.com Degré de séchage Type de textile Charge (kg) Prêt à Ranger Pour les articles à ranger directement Coton et lin (peignoirs, serviettes de bain, etc.
FRANÇAIS 25 9. RÉGLAGES 9.1 Sécurité enfants Avec cette option, vous pouvez empêcher les enfants de jouer avec le bandeau de commande. • Pour activer/désactiver cette option, appuyez simultanément sur les touches Tache/Prélavage et Départ • L'appareil présente une anomalie de fonctionnement (suite de signaux courts pendant environ 5 minutes).
www.aeg.com 10.2 Avant la mise en marche de l'appareil 1. Assurez-vous que la fiche du câble d'alimentation est bien insérée dans la prise de courant. 2. Assurez-vous que le robinet d'eau est ouvert. 10.3 Mise en fonctionnement de l'appareil et sélection d'un programme 1. Appuyez sur la touche Marche/Arrêt pendant quelques secondes pour allumer l'appareil. Le sélecteur de programme est automatiquement positionné sur le programme Coton, et seul le voyant Lavage est allumé.
FRANÇAIS Si vous modifiez le programme de lavage après avoir fermé le hublot, il est possible que s'affiche pour indiquer une possible surcharge : ouvrez le hublot et sortez quelques articles. 10.5 Ajout du produit de lavage et des additifs 27 Après un cycle de lavage, si nécessaire, éliminez les résidus de lessive du distributeur de produit de lavage. 10.6 Vérifiez la position du volet 1. Tirez le distributeur de produit de lavage jusqu'à la butée. 2.
www.aeg.com Le voyant correspondant cesse de clignoter et reste fixe. Sur l'affichage, le voyant de la phase en cours commence à clignoter et l'indicateur du pourcentage de détergent s'éteint. Le programme démarre et le hublot est verrouillé. L'indicateur s'allume. La pompe de vidange peut momentanément se mettre en route lorsque l'appareil se remplit d'eau. Avec le volet en position BASSE : • N'utilisez pas de lessives liquides gélatineuses ou épaisses.
FRANÇAIS 2. Appuyez à plusieurs reprises sur la touche Départ Différé jusqu'à ce que le départ différé souhaité s'affiche. 3. Appuyez de nouveau sur la touche Départ/Pause pour lancer le nouveau décompte. 10.9 Détection de la charge ProSense Par ex., la phase de rinçage est en cours : . Durant le cycle de lavage, l'appareil mélange le détergent, le détachant pour le traitement des tissus et/ou l'assouplissant avec de l'eau avant de les libérer dans le tambour.
www.aeg.com 10.13 Ouverture de la porte Ajout de vêtements Pendant le déroulement d'un programme ou du départ différé, le hublot de l'appareil est verrouillé. Si la température et le niveau de l'eau dans le tambour sont trop élevés et que le tambour continue de tourner, vous ne pouvez pas ouvrir le hublot. 1. Appuyez sur la touche Départ/Pause. Sur l'affichage, le voyant Hublot verrouillé s'éteint. 2. Ouvrez le hublot de l'appareil. Si nécessaire, ajoutez ou retirez du linge. 3.
FRANÇAIS Dans tous les cas, l'appareil vidange l'eau automatiquement au bout d'environ 18 heures. 10.16 Option de mise en veille 31 Appuyez sur la touche Marche/Arrêt pour remettre l'appareil en marche. L'affichage indique la fin du dernier programme sélectionné. Tournez le sélecteur pour choisir un nouveau cycle. Si vous sélectionnez un programme ou une option se terminant avec de l'eau dans le tambour, la fonction Veille n'éteint pas l'appareil pour vous rappeler qu'il faut vidanger l'eau.
www.aeg.com indique également la charge maximale recommandée pour un programme de lavage et de séchage (par ex. 6 kg pour le coton). 5. Ouvrez le hublot et chargez le linge, un article à la fois. Sur l'affichage, le poids du linge est mis à jour par paliers de 0,5 kg et la durée du programme est adaptée en fonction. 6. Fermez le hublot. 7. Versez le produit de lavage et les additifs dans le compartiment approprié.
FRANÇAIS 33 12. UTILISATION QUOTIDIENNE - SÉCHAGE UNIQUEMENT AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. Cet appareil est un sèchelinge automatique. 12.1 Préparation au séchage 1. Appuyez sur la touche Marche/Arrêt pendant quelques secondes pour mettre en fonctionnement l'appareil. Si vous sélectionnez un programme de séchage uniquement, l'affichage n'indique pas le poids du linge, et l'estimation PROSENSE est désactivée. 2. Chargez le linge dans le tambour, un article à la fois.
www.aeg.com • Le symbole s'affiche. • Le voyant de la touche Départ/Pause s'éteint. Le voyant de verrouillage du 1. Sortez le linge de l'appareil. 2. Vérifiez que le tambour est vide. Après la phase de séchage, nettoyez le tambour, le joint et l'intérieur du hublot avec un chiffon humide. hublot s'éteint. • Appuyez sur la touche Marche/Arrêt pendant quelques secondes pour éteindre l'appareil.
FRANÇAIS • Boutonnez les taies d'oreiller, fermez les fermetures à glissière et à pression et les crochets. Attachez les ceintures. • Videz les poches et retournez-les. • Retournez les tissus multi-couches, en laine et les articles portant des illustrations imprimées vers l'intérieur. • Traitez au préalable les taches tenaces. • Lavez les taches incrustées avec un produit spécial. • Traitez les rideaux avec précautions.
www.aeg.com Utilisez la bonne quantité d'adoucisseur d'eau. Respectez les instructions qui se trouvent sur les emballages du produit. 14.6 Préparation du cycle de séchage • Ouvrez le robinet d'eau. • Vérifiez que le tuyau d'évacuation est bien raccordé. Pour plus d'informations, reportez-vous au chapitre « Installation ». • Reportez-vous au tableau des programmes de séchage pour connaître les charges de linge maximales des programmes de séchage. 14.
FRANÇAIS 15.1 Nettoyage extérieur Nettoyez uniquement l'appareil à l'eau chaude avec un savon doux. Séchez complètement toutes les surfaces. 37 2. Lancez le programme pour le coton à température maximale avec une petite quantité de lessive en poudre. 15.4 Joint du hublot ATTENTION! N'utilisez pas d'alcool, de solvants ni de produits chimiques. ATTENTION! Ne nettoyez pas les surfaces métalliques avec un détergent à base de chlore. 15.
www.aeg.com 1 2 2. Retirez la partie supérieure du compartiment réservé à l'additif pour faciliter le lavage, et passez-le sous l'eau courante chaude pour éliminer toute trace d'accumulation de lessive. Après le nettoyage, remettez la partie supérieure en place. 15.7 Nettoyage de la pompe de vidange AVERTISSEMENT! Débranchez la fiche d'alimentation de la prise secteur. Vérifiez régulièrement le filtre de la pompe de vidange et assurez-vous qu'il est propre.
FRANÇAIS 39 7. Tournez le filtre vers la fauche pour le retirer. 2 1 2. Placez un récipient sous le logement de la pompe de vidange pour recueillir l'eau qui s'écoule. 3. Ouvrez la goulotte vers le bas. Gardez toujours un chiffon à portée de main pour essuyer l'eau qui peut s'écouler lorsque vous retirez le filtre. 4. Tournez le filtre à 180 degrés vers la gauche pour l'ouvrir, sans le retirer. Laissez l'eau s'écouler. 1 2 8. Si nécessaire, retirez les peluches et objets du logement du filtre. 9.
www.aeg.com 2 1 2 1 3 12. Fermez le couvercle de la pompe. 2. Retirez le tuyau d'arrivée de l'appareil en desserrant la bague de serrage. 2 1 Lorsque vous vidangez l'eau avec la vidange d'urgence, vous devez réactiver le système de vidange : a. Versez 2 litres d'eau dans le distributeur de produit de lavage pour le lavage principal. b. Démarrez le programme pour vidanger l'eau. 3. Utilisez une brosse à dents pour nettoyer le filtre de la valve situé à l'arrière de l'appareil. 15.
FRANÇAIS 41 évacuez toute l'eau restant dans le tuyau d'alimentation et la pompe de vidange. 45° 20° 15.9 Vidange d'urgence 1. Débranchez la fiche d'alimentation de la prise secteur. 2. Fermez le robinet d'eau. 3. Placez les deux extrémités du tuyau d'alimentation dans un récipient et laissez l'eau s'écouler du tuyau. 4. Videz la pompe de vidange. Reportez-vous à la procédure de vidange d'urgence. 5. Une fois que la pompe de vidange est vide, réinstallez le tuyau d'alimentation.
www.aeg.com Si l'appareil est trop chargé, retirez des vêtements du tambour et/ou poussez sur le hublot tout en appuyant sur la touche Départ/ Pause jusqu'à ce que le • - L'alimentation électrique est instable. Attendez que l'alimentation électrique se stabilise. • - Il n'y a aucune communication entre les composants électroniques de l'appareil. Éteignez puis rallumez l'appareil. Le programme ne s'est pas terminé correctement, ou l'appareil s'est arrêté trop tôt.
FRANÇAIS 43 Problème Solution possible L'appareil se remplit d'eau et se vidange immédiatement. • Vérifiez que la position du tuyau de vidange est correcte. Le tuyau est peut-être positionné trop bas. Reportez-vous au chapitre « Instructions d'installation ». L'appareil ne vidange pas l'eau. • Assurez-vous que le siphon de l'évier n'est pas obstrué. • Assurez-vous que le tuyau de vidange n'est pas tordu ni plié. • Assurez-vous que le filtre de vidange n'est pas obstrué.
www.aeg.com Problème Solution possible La durée du programme augmente ou diminue durant l'exécution du programme. • La fonction ProSense est capable d'ajuster la durée du programme en fonction du type et de la quantité de linge. Reportez-vous au paragraphe « Fonction ProSense » dans le chapitre « Utilisation quotidienne ». Les résultats de lavage ne sont pas satisfaisants. • Augmentez la quantité de produit de lavage ou utilisez-en un autre.
FRANÇAIS 16.3 Ouverture d'urgence du hublot En cas de panne d'alimentation ou d'anomalie de l'appareil, le hublot reste verrouillé. Le programme de lavage continue dès que l'alimentation est rétablie. Si le hublot reste verrouillé en cas d'anomalie, il est possible de l'ouvrir à l'aide du dispositif de déverrouillage d'urgence. Avant d'ouvrir le hublot : 45 Pour ouvrir le hublot, procédez comme suit : 1. Appuyez sur la touche Marche/Arrêt pour éteindre l'appareil. 2.
www.aeg.com Au cours du programme de lavage, la technologie ProSense peut faire varier la durée du lavage et les valeurs de consommation. Pour plus de détails, consultez le paragraphe« La détection de charge Prosense » du chapitre « Utilisation quotidienne ». Programmes Charge Consom- Consomma(kg) mation tion d'eau énergéti- (litres) que (kWh) Durée approximative du programme (minutes) Coton 60 °C 10 1.70 90 230 Coton Eco Programme Coton Éco à 10 0.86 61 265 Coton 40 °C 10 1.
FRANÇAIS Charge de séchage maximale Coton Synthétiques 6 kg 4 kg Vitesse d'essorage Vitesse d'essorage maximale 1550 tr/min 47 1) Raccordez le tuyau d'arrivée d'eau à un robinet fileté 3/4'' . 19. ACCESSOIRES 19.1 Disponible sur www.aeg.com/shop ou chez un revendeur agréé 19.3 Socle à tiroir Seuls les accessoires appropriés et agréés par AEG peuvent répondre aux normes de sécurité de l'appareil. Si les pièces ne sont pas agréées, toute réclamation sera refusée. 19.
www.aeg.
FRANÇAIS 49
www.aeg.
FRANÇAIS 51
157024280-A-402018 www.aeg.