L8WS86609 USER MANUAL DE Benutzerinformation Wasch-Trockner
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................6 3. MONTAGE................................................................................................................... 8 4. GERÄTEBESCHREIBUNG......................................................................................... 13 5.
DEUTSCH 3 Änderungen vorbehalten. 1. SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com • • • Halten Sie Kinder und Haustiere vom geöffneten Gerät fern. Falls Ihr Gerät mit einer Kindersicherung ausgestattet ist, empfehlen wir, diese einzuschalten. Kinder dürfen keine Reinigung und Wartung ohne Beaufsichtigung durchführen. 1.2 Allgemeine Sicherheit • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Dieses Gerät ist für die Verwendung im Haushalt und ähnliche Zwecke vorgesehen, wie z. B.
DEUTSCH • • • • • • • • • • • • 5 Der Raum, in dem das Gerät aufgestellt wird, muss gut belüftet sein, damit keine Gase in den Raum zurückströmen, die von offenem Feuer oder von anderen Geräten stammen, die mit Brennstoffen arbeiten. Die Abluft darf nicht über denselben Abzug abgeleitet werden, über den der Dunstabzug von mit Gas oder sonstigen Brennstoffen betriebenen Geräten erfolgt.
www.aeg.com • • • • • • • gummibeschichtete Wäschestücke sowie Kleider oder Kissen mit Schaumgummipolstern dürfen nicht im Waschtrockner getrocknet werden. Weichspüler oder ähnliche Produkte dürfen nur entsprechend den Herstelleranweisungen benutzt werden. Entfernen Sie alle Gegenstände aus der Wäsche, die eine Entzündungsquelle darstellen könnten, z. B. Feuerzeuge oder Streichhölzer.
DEUTSCH • Bewahren Sie die Transportschrauben an einem sicheren Ort auf. Wenn das Gerät in Zukunft umgesetzt werden soll, müssen sie wieder angebracht werden, um die Trommel zu verriegeln und dadurch interne Schäden zu vermeiden. • Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk. • Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht.
www.aeg.com WARNUNG! Verletzungsgefahr sowie Risiko von Schäden am Gerät. • Setzen oder stellen Sie sich niemals auf die geöffnete Gerätetür. • Trocknen Sie keine tropfnassen Wäschestücke im Gerät. 2.5 Service • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. 2.6 Entsorgung • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung. • Schneiden Sie das Netzkabel in der Nähe des Geräts ab, und entsorgen Sie es.
DEUTSCH 5. Legen Sie das Gerät vorsichtig auf seine Rückseite. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 9 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. Aus dem Ablaufschlauch könnte Wasser austreten. Dies ist auf den Gerätetest mit Wasser im Werk zurückzuführen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 10.
www.aeg.com Das Gerät muss einen waagerechten und festen Stand haben. Durch eine korrekte waagrechte Ausrichtung des Geräts werden Vibrationen, Geräusche und ein Wandern des Geräts während des Betriebs vermieden. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren. 3.2 Aufstellen und Ausrichten 1. Stellen Sie das Gerät auf einen ebenen, festen Boden. Stellen Sie sicher, dass die Luftzirkulation unter dem Gerät nicht durch Teppiche beeinträchtigt wird.
DEUTSCH Vergewissern Sie sich, dass sich der Zulaufschlauch nicht in der vertikalen Position befindet. 3. Lösen Sie ggf. die Ringmutter, um ihn in die gewünschte Position zu bringen. 4. Schließen Sie den Wasserzulaufschlauch an einen Kaltwasserhahn mit einem 3/4"Außengewinde an. 11 den autorisierten Kundendienst, um den Schlauch zu erneuern. 3.5 Ablassen des Wassers Der Ablaufschlauch muss in einer Höhe nicht unter 60 cm und nicht über 100 cm vom Boden angebracht werden.
www.aeg.com Achten Sie darauf, dass sich das Ende des Ablaufschlauchs nicht im Wasser befindet. Anderenfalls könnte Schmutzwasser in das Gerät zurückfließen. 3. In ein Standrohr mit Belüftungsöffnung - Stecken Sie den Ablaufschlauch direkt in das Ablaufrohr. Orientieren Sie sich an der Abbildung. Das Ende des Ablaufschlauchs muss stets belüftet sein, d. h. der Innendurchmesser des Ablaufrohrs (min. 38 mm min. 1,5") muss größer sein als der Außendurchmesser des Ablaufschlauchs. 4.
DEUTSCH 4. GERÄTEBESCHREIBUNG 4.
www.aeg.com 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 4 5 13 12 Programmwahlschalter Display Sensortaste Trockenzeit (Trockenzeit) Sensortaste Trockengrad (Trockengrad) 5 Sensortaste Waschen und Trocknen (Waschen/Trocknen) • Washen • Trocknen Sensortaste Start und Pause (Start/ 6 Pause) 1 2 3 4 5.
DEUTSCH 15 Wäschegewichtsanzeige. Das Symbol blinkt während der Messung der Wäschemenge (siehe Abschnitt „PROSENSE Beladungserkennung“). Anzeige des max. zulässigen Wäschegewichts. Blinkt, wenn das Wäschegewicht die maximal zulässige Füllmenge für das ausgewählte Programm überschreitet. Anzeige der Waschmittelmenge: Der Wert zeigt den benötigten Prozentsatz der Waschmittelmenge an. Kindersicherungsanzeige. Trockenzeitanzeige. Türverriegelungsanzeige.
www.aeg.com Temperaturanzeige. Die Anzeige mit kaltem Wasser gewählt wurde. erscheint, wenn ein Waschgang Schleuderdrehzahlanzeige. Spülstoppanzeige. Anzeige Extra Leise. Vorwäscheanzeige. Fleckenanzeige. ECO Energiesparanzeigen. Sie erscheinen, wenn das Programm Baumwolle Eco eingestellt ist. Zeitvorwahlanzeige. 6. PROGRAMMWAHLSCHALTER UND TASTEN 6.1 Ein/Aus Halten Sie diese Taste einige Sekunden lang gedrückt, um das Gerät ein- oder auszuschalten.
DEUTSCH Wenn das Display die Symbole und anzeigt, heizt das Gerät das Wasser nicht auf. 6.4 U./Min. Wenn Sie ein Programm auswählen, stellt das Gerät automatisch die höchste Schleuderdrehzahl ein. Drücken Sie diese Taste wiederholt, um • Die Schleuderdrehzahl zu reduzieren. Das Display zeigt nur die Schleuderdrehzahlen an, die für das eingestellte Programm verfügbar sind. • Die Option Spülstopp einzuschalten.
www.aeg.com Diese beiden Optionen können nicht zusammen gewählt werden. 6.6 Zeitvorwahl Mit dieser Option kann sich die Programmdauer verlängern. Durch Berühren einer beliebigen Taste stoppt diese Knitterschutzbewegung und die Tür wird entriegelt. Mit dieser Option können Sie den Programmstart verzögern, um eine günstigere Zeit zu nutzen. 6.9 Trockenzeit Tippen Sie wiederholt auf die Taste, um die erforderliche Zeitvorwahl einzustellen.
DEUTSCH • Nur Trocknen : Die Kontrolllampe Trocknen leuchtet. 19 6.12 Start/Pause Berühren Sie die Taste Start/Pause, um das Gerät zu starten, anzuhalten oder ein laufendes Programm zu unterbrechen. 7. PROGRAMME 7.1 Programmübersicht Programm Programmbeschreibung Waschprogramme Baumwolle Baumwolle Eco Weiße und bunte Baumwollwäsche. Normal, stark und leicht verschmutzt. Weiße und bunte Baumwollwäsche. Normal, stark und leicht verschmutzt. Baumwolle-Energiesparprogramm.
www.aeg.com Programm Programmbeschreibung ÖKOPower Mischgewebe (Baumwolle und pflegeleichte Wäsche). Komplettprogramm zum Waschen und Trocknen von 5 kg Wäsche in nur 4 Stunden. Die Anzeige erscheint ebenfalls im Display. Dampfprogramm Dampfprogramme2) Dampf Dampf kann für getrocknete, gewaschene oder einmal getragene Wäsche benutzt werden. Diese Programme können Falten und Gerüche reduzieren und machen Ihre Wäsche weicher. Verwenden Sie kein Waschmittel.
DEUTSCH Programmtemperatur, maximale Schleuderdrehzahl und maximale Beladung Programm Standardtemperatur Temperaturbereich Referenzschleuderdrehzahl Schleuderdrehzahlbereich Maximale Beladung Baumwolle 40 °C 95 °C – kalt 1600 U/min 1600 U/min – 400 U/min 10 kg Baumwolle Eco 60 °C 60 °C - 40 °C 1600 U/min 1600 U/min – 400 U/min 10 kg Pflegeleicht 40 °C 60 °C – kalt 1200 U/min 1200 U/min – 400 U/min 4 kg Feinwäsche 40 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 4 kg Wolle/Handwäsche
www.aeg.com ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Schleudern/Abpumpen ÖKOPower ■ Spülen Outdoor ■ Dampf Feinwäsche Extra Leise Pflegeleicht Spülstopp Baumwolle Eco U./Min.
Trockengrad 23 Schleudern/Abpumpen Spülen Dampf ÖKOPower Outdoor Wolle/Handwäsche ■4) Feinwäsche ■ Pflegeleicht Baumwolle Eco Optionen Baumwolle Programm DEUTSCH 1) Stellen Sie die Option Kein Schleudern ein, wird lediglich das Wasser aus dem Gerät gepumpt. 2) Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C. 3) Wenn Sie die kürzeste Programmdauer einstellen, empfehlen wir Ihnen, die Wäschemenge zu verringern.
www.aeg.com Trockengrad Schranktrocken1) Für Wäsche, die in den Schrank gelegt werden soll Bügeltrocken Bügeltrocken Gewebetyp Beladung Baumwolle und Leinen (Bademäntel, Badetücher usw.
DEUTSCH Trockengrad Gewebetyp Beladung (kg) Schranktrocken Baumwolle und Leinen Für Wäsche, die (Bademäntel, Badetücher usw.) in den Schrank gelegt werden soll Pflegeleichte Wäsche und Mischgewebe (Pullover, Blusen, Unterwäsche, Haushalts- und Bettwäsche) Bügeltrocken Bügeltrocken 25 Schle Vorgeschlauderd gene Dauer reh(Min.
www.aeg.com starten Sie das Programm ohne Wäsche. So werden alle eventuellen Verunreinigungen aus Trommel und Bottich entfernt. 9. EINSTELLUNGEN 9.1 Kindersicherung Diese Option verhindert, dass Kinder mit dem Bedienfeld spielen. • Berühren Sie zum Ein-/Ausschalten dieser Option die Tasten Flecken/ Vorw. und Zeitvorwahl gleichzeitig, bis im Display leuchtet/ die Anzeige erlischt.
DEUTSCH 10.1 Verwendung der Gewichtssensoren Für eine korrekte Verwendung des Gewichtssensors muss die Trommel beim Einschalten leer sein. Stellen Sie das Programm ein, BEVOR Sie Wäsche in die Trommel geben. 10.2 Vor dem Einschalten des Geräts 1. Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. 2. Stellen Sie sicher, dass der Wasserzulaufhahn geöffnet ist. 10.3 Einschalten des Geräts und Einstellen eines Programms 1.
www.aeg.com Maximaler Füllstand für flüssige Pflegemittel. Klappe für Waschpulver oder Flüssigwaschmittel. 4. Auf dem Display wird der benötigte Prozentsatz der Waschmittelmenge . angezeigt Dies ist ein Richtwert und bezieht sich auf die Waschmitteldosierung, die auf der Waschmittelverpackung für eine maximale Beladung empfohlen wird.
DEUTSCH 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. 29 Achten Sie darauf, dass die Klappe beim Schließen der Waschmittelschublade nicht blockiert. 10.7 Starten eines Programms Berühren Sie die Taste Start/Pause, um das Programm zu starten. Die zugehörige Anzeige hört auf zu blinken und leuchtet konstant. Im Display blinkt die Anzeige der Programmphase und die Waschmittelprozent-Anzeige erlischt. Das Programm startet, die Tür ist verriegelt.
www.aeg.com Abbrechen der Zeitvorwahl nach dem Start des Countdowns Abbrechen der Zeitvorwahl: 1. Berühren Sie die Taste Start/Pause, um das Gerät in den Pausenmodus zu schalten. Die zugehörige Anzeige blinkt. 2. Berühren Sie die Taste Zeitvorwahl wiederholt, bis im Display erscheint. 3. Berühren Sie die Taste Start/Pause erneut, um das Programm sofort zu starten. Ändern der Zeitvorwahl nach dem Start des Countdowns Ändern der Zeitvorwahl: 1.
DEUTSCH 10.12 Abbrechen eines laufenden Programms 1. Drücken Sie die Taste Ein/Aus, um das Programm abzubrechen und das Gerät auszuschalten. 2. Drücken Sie die Taste Ein/Aus erneut, um das Gerät einzuschalten. Anschließend können Sie ein neues Waschprogramm einstellen. Wurde die ProSense-Phase bereits beendet und läuft Wasser in das Gerät ein, startet das neue Programm ohne die ProSense-Phase zu wiederholen. Um Wasser und Waschmittel nicht zu verschwenden, wird das Wasser nicht abgepumpt. 10.
www.aeg.com • Die Trommel dreht sich regelmäßig weiter, um Knitterfalten in der Wäsche zu vermeiden. • Die Tür bleibt verriegelt. • Sie müssen das Wasser abpumpen, um die Tür öffnen zu können: 1. Berühren Sie bei Bedarf die Taste U./ Min., um die vom Gerät vorgeschlagene Schleuderdrehzahl zu verringern. 2. Berühren Sie die Taste Start/Pause: gewählt haben, • Wenn Sie pumpt das Gerät das Wasser ab und schleudert. • Wenn Sie gewählt haben, pumpt das Gerät nur das Wasser ab.
DEUTSCH 33 Nicht automatische Waschund Trockenprogramme 11.2 Waschen und Trocknen – Automatikstufen In einigen Waschprogrammen können Sie die Modi Washen und Trocknen kombinieren, um ein komplettes Waschund Trockenprogramm auszuführen. 1. Tippen Sie wiederholt auf die Taste Trockengrad, bis im Display der gewünschte Trockengrad angezeigt wird. Die Anzeigen im Display leuchten entsprechend: Gehen Sie hierzu folgendermaßen vor: 1.
www.aeg.com neu eingestellte Trockenzeit erscheint auf dem Display. 2. Berühren Sie Start/Pause, um das Programm zu starten. Die PROSENSE Erkennung startet. Im Display erscheint die Türverriegelungsanzeige , und die Anzeige der Programmphase blinkt. Das Display zeigt auch die Restlaufzeit an. 11.4 Am Ende des Trockenprogramms • Halten Sie die Ein/Aus-Taste einige Sekunden lang gedrückt, um das Gerät auszuschalten.
DEUTSCH b. Schranktrocken: für Baumwolle und pflegeleichte Textilien c. Extra Trocken: für Baumwollwäsche Im Display wird die Dauer des Trockenprogramms angezeigt. Um ein gutes Trockenergebnis bei einem geringeren Energieverbrauch und in einer kürzeren Zeit zu erzielen, können Sie für die zu waschende und trocknende Wäsche keine zu niedrige Schleuderdrehzahl einstellen. 2. Berühren Sie die Taste Start/Pause, um das Programm zu starten.
www.aeg.com • Reinigen Sie nach der Trockenphase die leere Trommel, die Dichtung und die Tür gründlich mit einem feuchten Tuch. Starten Sie ein spezielles Programm, um die Flusen aus der Trommel zu entfernen: • Leeren Sie die Trommel. • Reinigen Sie die Trommel, die Dichtung und die Tür gründlich mit einem feuchten Tuch. • Wählen Sie das Programm „Spülen“. • Drücken Sie gleichzeitig die Tasten Flecken/Vorw. und Knitterschutz, bis im Display CLE erscheint, um die Reinigungsfunktion einzuschalten.
DEUTSCH – Flüssigwaschmittel, vorzugsweise für Programme mit niedrigen Temperaturen (max. 60 °C) für alle Gewebearten oder Wollwaschmittel. • Mischen Sie nicht verschiedene Waschmittel. • Verwenden Sie der Umwelt zuliebe nicht mehr als die empfohlene Waschmittelmenge. • Halten Sie sich an die Anweisungen auf der Verpackung der Wasch- und Pflegemittel und überschreiten Sie ).
www.aeg.com 14.10 Zusätzlicher Trockengang Ist die Wäsche am Ende eines Trockenprogramms noch zu feucht, wählen Sie noch einen kurzen Trockengang. WARNUNG! Trocknen Sie die Wäsche nicht zu lang, um Knitterbildung und ein Einlaufen der Wäschestücke zu vermeiden. Mit der Erfahrung wird die Einstellung der Trockenzeiten leichter. Merken Sie sich die Dauer bereits durchgeführter Trockengänge. Zur Vermeidung elektrostatischer Aufladung nach dem Trocknen: 1. Verwenden Sie beim Waschen einen Weichspüler. 2.
DEUTSCH Temperatur und einer kleinen Menge Waschpulver. 39 1 15.4 Türdichtung 2 Überprüfen Sie die Türdichtung regelmäßig und entfernen Sie ggf. darin verfangene Gegenstände. 2. Entfernen Sie das Oberteil des Pflegemittelfachs, um die Reinigung zu vereinfachen, und spülen Sie es mit fließendem warmen Wasser aus, um das angesammelte Waschmittel zu beseitigen. Setzen Sie nach der Reinigung das Oberteil wieder ein. 15.
www.aeg.com 2 1 15.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Stellen Sie einen geeigneten Behälter unter die Öffnung der Ablaufpumpe, um das abfließende Wasser aufzufangen. 3. Öffnen Sie den Schacht nach unten. Halten Sie beim Herausnehmen des Siebs einen Lappen bereit, um austretendes Wasser aufzuwischen. Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist.
DEUTSCH 6. Wiederholen Sie die Schritte 4 und 5, bis kein Wasser mehr herausfließt. 7. Drehen Sie das Sieb gegen den Uhrzeigersinn, um es zu entfernen. 41 2 1 1 2 12. Schließen Sie die Pumpenabdeckung. 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, ob sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst.
www.aeg.com 1 2 45° 3 20° 2. Lockern Sie die Ringmutter, um den Zulaufschlauch vom Gerät zu entfernen. 15.9 Notentleerung Kann das Gerät das Wasser nicht abpumpen, führen Sie den unter „Reinigen der Ablaufpumpe“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 1.
DEUTSCH 43 WARNUNG! Stellen Sie sicher, dass die Temperatur über 0 °C liegt, bevor Sie das Gerät wieder einschalten. Der Hersteller ist nicht für Schäden verantwortlich, die auf zu niedrige Temperaturen zurückzuführen sind. 16. FEHLERSUCHE Ist das Gerät überladen, nehmen Sie einige Wäschestücke aus der Trommel und/oder drücken Sie die Tür zu und berühren Sie gleichzeitig die Taste Start/Pause, bis die WARNUNG! Siehe Kapitel Sicherheitshinweise. 16.
www.aeg.com zu. Wenden Sie sich an einen autorisierten Kundendienst. WARNUNG! Schalten Sie das Gerät vor der Überprüfung aus. 16.2 Mögliche Störungen Problem Das Programm startet nicht. Mögliche Abhilfe • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. • Stellen Sie sicher, dass Start/Pause berührt wurde.
DEUTSCH 45 Problem Mögliche Abhilfe Das Gerät schleudert nicht oder das Waschprogramm dauert länger als gewöhnlich. • Stellen Sie das Schleuderprogramm ein. • Vergewissern Sie sich, dass das Ablaufsieb nicht verstopft ist. Reinigen Sie ggf. das Sieb. Siehe „Reinigung und Pflege“. • Verteilen Sie die Wäschestücke mit der Hand neu und starten Sie die Schleuderphase erneut. Das Problem kann durch eine Unwucht verursacht worden sein. Es befindet sich Wasser auf dem Boden.
www.aeg.com Problem Mögliche Abhilfe Zu viel Schaum in der Trommel während des Waschprogramms. • Reduzieren Sie die Waschmittelmenge. Nach dem Waschgang befinden sich Waschmittelrückstände in der Waschmittelschublade. Die Trommel ist leer und im Display wird angezeigt, dass sich Wäsche darin befindet. • Stellen Sie sicher, dass sich die Klappe in der richtigen Position befindet (OBEN für Waschpulver - UNTEN für Flüssigwaschmittel).
DEUTSCH VORSICHT! Verbrennungsgefahr! Achten Sie darauf, dass die Wassertemperatur nicht zu hoch und die Wäsche nicht heiß ist. Warten Sie sonst, bis Wasser und Wäsche sich abgekühlt haben. VORSICHT! Verletzungsgefahr! Vergewissern Sie sich, dass die Trommel sich nicht dreht. Warten Sie sonst, bis die Trommel zum Stillstand gekommen ist. Stellen Sie sicher, dass der Wasserstand in der Trommel nicht zu hoch ist.
www.aeg.com Programme Beladung (kg) Baumwolle Eco Das Baumwolle-Energie- EnergieWasserververbrauch brauch (Li(kWh) ter) Ungefähre Programmdauer (in Minuten) 10 0.86 61 265 Baumwolle 40 °C 10 1.10 90 220 Pflegeleicht 40 °C 4 0.72 55 155 Feinwäsche 40 °C 4 0.60 59 89 Wolle/Handwäsche 30 °C 2 0.
DEUTSCH 49 19. ZUBEHÖR 19.1 Verfügbar im www.aeg.com/shop oder beim Vertragshändler 19.3 Sockel mit Schublade Nur mit geeignetem, von AEG zugelassenem Zubehör können die Sicherheitsstandards des Geräts gewährleistet werden. Werden nicht zugelassene Teile verwendet, erlischt jeglicher Gewährleistungsanspruch. 19.2 Satz Fixierplatten Wenn Sie das Gerät auf einem Sockel aufstellen, befestigen Sie es mithilfe der Fixierplatten. Lesen Sie die mit dem Zubehör gelieferte Gebrauchsanleitung sorgfältig durch.
www.aeg.
DEUTSCH 51
157023640-A-372018 www.aeg.