L98609 FL2 EN User manual
www.aeg.com CONTENTS 1. 2. 4. 5. 6. 8. 9. 10. 11. 18. 19. 20. 21. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 INTERIOR ACCESSORIES . . . . . . . . . . . . . . . . .
ENGLISH 3 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. 2.
ENGLISH Water connection 5 2.3 Care and Cleaning • Make sure not to cause damage to the water hoses. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. 2.
www.aeg.com Level of protection against ingress of solid particles and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture Water supply pressure IPX4 Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Cold water Water supply 1) Maximum load Cotton 10 kg Spin speed Maximum 1600 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 4.
ENGLISH 7 5. INTERIOR ACCESSORIES 1 1 Spanner 2 To remove the transit bolts. 2 Plastic caps 5 4 To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Sound barrier To decrease the noise while the appliance operates. 4 Plastic hose guide To connect the drain hose on the edge of a sink. 5 Anti-flood inlet hose To prevent possible leakage. 3 6.
www.aeg.com 7.1 TOUCH SCREEN Do not wear gloves when you touch the buttons. Make sure the touch screen and buttons are always clean and dry. 7.2 AUTO Off button 1 Press this button to activate or deactivate the appliance. A tune sounds when the appliance is activated. The AUTO OFF function automatically deactivates the appliance to stop the energy consumption when: • You do not use the appliance for 5 minutes before you press button 6 . – All settings are cancelled.
ENGLISH 9 • The time of the day When you activate the appliance the display shows the time of the day for some seconds. To adjust the clock, refer to "Clock setting". • The programme duration When the washing programme starts, the programme time decreases every minute. Programme duration symbol The symbol comes on when the digits shows the programme duration. D • The end time of the washing programme . Programme end symbol The symbol comes on when the digits shows the programme end time.
www.aeg.com Extra rinsing G The indicator bar fills accordingly the numbers of rinses. Stains Prewash H Soak The indicator bar fills accordingly to the set functions. The default spin speed of the programme. I ___ No spin 1) Rinse hold 1) Only available for Spin/Drain programme. The default temperature of the programme. J Cold wash 7.5 STEAM BUTTON 4 Touch button 4 to set the steam level. This is possible only with programmes where the steam function is available.
ENGLISH 7.10 EXTRA RINSE BUTTON 9 Touch button 9 to add rinsing phases to a programme. Use this function for persons allergic to detergents and in areas where the water is soft. 7.11 STAIN, PREWASH AND SOAK BUTTON 10 Touch button 10 to set one of the these functions: STAIN Use this function for laundry with hard stains to remove. When you set this function, put the stain . remover into compartment The programme duration increases. This function is not available with a temperature lower than 40° C.
www.aeg.com • To deactivate the function touch button 8 and button 7 at the same time until the symbol goes off. 8. PROGRAMMES Programme Temperature Type of load Weight of load Programme description Functions Koch/Bunt- 95° - Cold White and coloured cotton with heavy level of soil. Maximum load 10 kg Wash Rinses Long spin Spin Reduction Spülstopp Flecken1) Vorwäsche2) Einweichen Extra Spülen Zeit Sparen3) Extra Leise 95° - Cold White and coloured cotton with normal level of soil.
ENGLISH Programme Temperature Type of load Weight of load 40° - Cold Rinses Short spin Machine washa- Wash ble wool as well Rinses as for hand wash- Short spin able woollens and delicate fabrics with «hand washing» care symbol. Maximum load 2 kg Spin Reduction Spülstopp Daunen 60° - 30° Rinses Short spin Special proWash gramme for one Rinses synthetic blanket, Short spin duvet, bedspread and so on. Maximum load 3 kg Spin Reduction Anti-Allergie 60° White cotton items.
www.aeg.com Programme Temperature Type of load Weight of load Programme description Functions Super Eco 0° Mixed fabrics (cotton and synthetic items)8). Maximum load 3 kg Wash Rinses Long spin Spin Reduction Spülstopp Extra Spülen 60° or 40° White and fast coloured cotton with the normal soil10). Maximum load 10 kg Wash Rinses Short spin Spin Reduction Spülstopp Flecken Vorwäsche2) Einweichen Extra Spülen Zeit Sparen3) Baumwolle Eco 9) 1) Not available with temperature lower than 40°C.
ENGLISH Cotton and synthetic items. Dampf Glätten2) This programme helps to dewrinkle the laundry. 15 up to 1.5 Kg Steam can be used for dried, washed or worn once laundry. These programmes can reduce creases and odours and make your laundry more smooth. Do not use any detergent. If necessary, remove stains by washing or using localized stain removal. Steam programmes do not perform any hygienic cycle.
www.aeg.com Programmes Load (Kg) Energy con- Water consumption sumption (li(kWh) tre) Approximate programme duration (minutes) Remaining moisture (%)1) Cottons 60 °C 10 1.80 82 185 43 Cottons 40 °C 10 1.10 82 185 43 Synthetics 40 °C 4 0.60 55 100 35 Delicates 40 °C 4 0.70 62 86 35 Wool/Hand wash 30 °C 2 0.50 59 60 30 Standard cotton programmes Standard 60 °C cotton 10 1.14 69 249 43 Standard 60 °C cotton 5 0.77 45 167 43 Standard 40 °C cotton 5 0.
ENGLISH Change the language after the first activation 1. Touch button 11 and button 10 at the same time for some seconds. 2. When display shows the language set, turn the programme knob to set the new language. 3. Touch button 6 to confirm the selection. 10.2 Clock setting After you set the language, the display tells to set the clock: • The hour digits flash. • Turn the programme knob to change the hour. • Touch button 6 to confirm the selection. • The minute digits flash.
www.aeg.com 13. LOADING THE LAUNDRY Open the appliance door. The display (E) shows the maximum programme load for the programme (MAX ) and the weight of the laundry (KG). The text bar on the display tells to add the laundry. 3. Put the laundry in the drum, one item at a time. Shake the items before you put them in the appliance. 4. On the display the weight of the laundry updates by step of kg 0.5. The weight is indicative and changes with the type of the laundry. 1. 2. 5. Close the door.
ENGLISH 19 14. FILLING THE DETERGENT AND ADDITIVES The detergent compartment for the prewash phase and the soak programme. Add the detergent for prewash and soak before the start of the programme. The detergent compartment for the washing phase. If you use a liquid detergent, put it immediately before you start the programme. Liquid additives compartment (fabric conditioner, starch). Put the product in the compartment before you start the programme.
www.aeg.com 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6. Measure out the detergent and the fabric conditioner. Carefully close the detergent dispenser.
ENGLISH The appliance adjust automatically the cycle time to the laundry you have put in the drum to have perfect washing results in the minimum necessary time. After approximately 15 minutes from the start of the programme, the display shows the new time value. 2. 3. 21 Change the function set. Touch button 6 again. The washing programme continues. 16.4 Open the door While a programme or the delay start operates, the appliance door is locked. To open the appliance door: 1. 16.
www.aeg.com The washing programme is completed, but there is water in the drum: – The drum turns regularly to prevent the creases in the laundry. – The door stays locked. – You must drain the water to open the door. To drain the water: 1. If necessary, decrease the spin speed. 2. Touch button 6 . The appliance drains the water and spins. 3. When the programme is completed and the door lock symbol goes off, you can open the door 4. Press button 1 to deactivate the appliance.
ENGLISH chines. In areas where the water hardness is soft it is not necessary to use a water softener. To know the water hardness in your area, contact your local water authority. Obey the instructions that you find on the packaging of the products. Equivalent scales measure the water hardness: 23 • German degrees (°dH). • French degrees (°TH). • mmol/l (millimol for each litre - international unit for the hardness of water). • Clarke degrees. Water hardness table Level Type Water hardness °dH °T.H.
www.aeg.com 19.4 Door seal Regularly examine the seal and remove all objects from the inner part. 19.5 Drum Regularly examine the drum to prevent limescale and rust particles. Only use special products to remove rust particles from the drum. To do this: • Clean the drum with special product for stainless steel. • Start a short programme for cotton at the maximum temperature with a small quantity of detergent. 19.6 Detergent dispenser To clean the dispenser: 1 1. 2. Press the lever.
ENGLISH 19.7 Drain pump Regularly examine the drain pump and make sure that it is clean. 25 • The display shows an alarm code because of the problem with water drain. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates. Do not clean the drain pump if the water in the appliance is hot. The water must be cold before you clean the drain pump. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn.
www.aeg.com 2 1 19.8 The inlet hose filter and the valve filter 7. Remove fluff and objects from the pump. 8. Make sure that the impeller of the pump can turn. If this does not occur, contact the service centre. 9. Clean the filter under the water tap and put it back in the pump into the special guides. 10. Make sure that you tighten correctly the filter to prevent leakages. 11. Put the flap back and close the drain pump door.
ENGLISH 4. 5. 6. 7. 20° 27 Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 45° 19.9 Emergency drain Because of a malfunction, the appliance cannot drain the water. If this occurs, do steps (1) through (6) of 'To clean the drain pump'. If necessary, clean the pump. Put the drainage duct back and close the drain pump flap.
www.aeg.com Problem Possible cause The display tells The water tap is closed. to check the tap: the appliance does not fill with water. Possible solution Open the water tap. The water inlet hose is damaged. Make sure that the water inlet hose has no damages. The filters in the water inlet hose is blocked . Clean the filters. Refer to 'Care and cleaning'. The connection of the water inlet hose is not correct. Make sure that the connection is correct. The water pressure is too low.
ENGLISH 29 Problem Possible cause Possible solution The spin phase does not operate. The spin phase is off. Set the spin programme. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again. The mains plug is not connected in the mains socket. Put in the mains plug. Blow out fuse in the household fuse box. Replace the fuse.
www.aeg.com Problem Possible cause The washing results are not satisfactory. The detergent you used Increase the detergent quantity was not sufficient or cor- or use a different one. rect. Possible solution You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains. You set a not correct temperature. Make sure that you set the correct temperature. Too much laundry load. Decrease the laundry load. The internal lamp The lamp is burned.
ENGLISH 31 21.2 Unpacking 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum.
www.aeg.com 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. 8. Fully clean and dry the bottom of the appliance. Do not use alcohol, solvents or chemical products. 9. Make sure to identify the different sizes and the positions of the sound barriers.
ENGLISH 33 10. – Remove the adhesive strip from x4 A the silent barriers. – Attach the four barriers to bottom of the appliance. Refer to the illustration. – Make sure that the barriers are securely attached. Attach the sound barriers at a room temperature. B 11. Pull up the appliance in vertical po- sition. 12. Remove the power supply cable and the drain hose from the hose holders. 13. Turn the three bolts with the key supplied with the appliance. Pull out the plastic spacers.
www.aeg.com 14. Put the plastic caps in the holes. You can find these caps in the user manual bag. WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance. 21.3 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance.
ENGLISH 35 21.4 The inlet hose • Connect the hose to the appliance. Turn the inlet hose only left or right. Loose the ring nut to set it in the correct position. 20 O 45 O • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device.
www.aeg.com With the plastic hose guide. • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose.
ENGLISH You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension. 22. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste.
www.aeg.
ENGLISH 39
132918850-A-392012 www.aeg.
