L 98699 FL2 EN WASHING MACHINE USER MANUAL
www.aeg.com CONTENTS 4 5 6 7 8 13 17 17 18 22 23 25 30 33 SAFETY INFORMATION TECHNICAL INFORMATION PRODUCT DESCRIPTION INTERIOR ACCESSORIES CONTROL PANEL WASHING PROGRAMMES CONSUMPTION VALUES BEFORE FIRST USE USING THE APPLIANCE AT THE END OF PROGRAMME HELPFUL HINTS AND TIPS CARE AND CLEANING TROUBLESHOOTING INSTALLATION ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it.
ENGLISH 3 FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG webshop, you’ll find everything you need to keep all your AEG appliances looking spotless and working perfectly.
www.aeg.com SAFETY INFORMATION Before the installation and use, read this manual carefully: • For your safety and the safety of your property • To help the environment • For the correct operation of the appliance. Always keep these instructions with the appliance also if you move or give it to a different person. The manufacturer is not responsible if an incorrect installation and use causes damage.
ENGLISH To replace the internal lamp, contact the service centre. Disconnect the mains plug from the mains socket before the replacement of the internal lamp. INSTALLATION • The appliance is heavy, be careful when you move it. • Do not transport your appliance without the transit bolts, you can damage internal components and cause leakages or malfunctions. • Do not install and connect a damaged appliance. • Make sure to remove all packaging and transport bolts.
www.aeg.com Level of protection against ingress of solid particles and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture Water supply pressure IPX4 Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Water supply 1) Cold water Maximum load Cotton 9 kg Spin speed Maximum 1600 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread.
ENGLISH 7 INTERIOR ACCESSORIES 1 1 Spanner 2 To remove the transit bolts. 2 Plastic caps 5 4 3 To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Sound barrier To decrease the noise while the appliance operates. 4 Plastic hose guide To connect the drain hose on the edge of a sink. 5 Anti-flood inlet hose To prevent possible leakage.
www.aeg.com CONTROL PANEL 1 2 3 Ontkreuk Katoen Opfrissen Extra Stil Eco Super Eco Fijne Was Wol/ Zijde Dekbed Outdoor Auto Off Anti-Allergie 4 Geheugen 1 Strijkvrij 20 Min. - 3 kg Spoelen Centrifugeren/ Pompen Stoom Synthetica Geheugen 2 Temp.°C TPM 12 11 Vlekken/ Extra Tijd Voorw.
ENGLISH 9 DISPLAY 3 A J A I B H G C D F E The text bar: • Guides you in the use of the appliance. • Shows the programme status and phase. • Shows alarm messages. Refer to 'Troubleshooting' . The symbols appear on the display when the related phase or function is set. B Child lock C Door locked You cannot open the door when the symbol is on. You can open the door only when the symbol goes off. If the symbol stays on but the programme is completed: • There is water in the drum.
www.aeg.com • The time of delay – When you set the delayed start the time of the programme end increases by steps of 30 minutes till 10 hours and by steps of one hour till 20 hours. • The end of the programme The display shows a zero. This part comes on only if the door is open - Refer to 'Loading the laundry'. The programme maximum load The weight of the laundry E The indicator bar fills accordingly to the laundry weight. The indicator fully fills when you put the maximum load.
ENGLISH 11 Rinse hold 1) Only available for Spin/Drain programme. The default temperature of the programme. J Cold wash STOOM BUTTON 4 TIJD BESPAREN BUTTON 8 Touch button 4 to set the steam level. This is possible only with programmes where the steam function is available. The duration of the steam phase changes accordingly to your selection. Touch button 8 to decrease the programme time. You can select: SHORTENED DURATION To wash items with daily soil.
www.aeg.com The appliance soaks the laundry at 30°C for about half an hour before to wash. SPIN BUTTON 11 Touch button 11 to: • Decrease the maximum speed of the spin phase of the programme. The display shows only the spin speeds available with the set programme. • Deactivate the spin phase (' No Spin ' function). • Activate the ' Rinse Hold ' function. Set this function to prevent fabric creases. The appliance does not drain the water when the programme is completed.
ENGLISH 13 WASHING PROGRAMMES Programme Temperature Type of load Weight of load Programme description Functions Katoen 95° - Cold White and coloured cotton with heavy level of soil. Maximum load 9 kg Wash Rinses Long spin SPIN REDUCTION SPOELSTOP VLEKKEN1) VOORWAS2) INWEKEN EXTRA SPOELEN TIJD BESPAREN3) Extra Stil 95° - Cold White and coloured cotton with normal level of soil.
www.aeg.com Programme Temperature Type of load Weight of load Programme description Functions Fijne Was 40° - Cold Rinses Short spin Delicate fabrics as acrylics, viscose, polyester items with normal soil.
ENGLISH 15 Programme Temperature Type of load Weight of load Programme description Functions Outdoor 40° - Cold Waterproof, sports and outdoor clothing. Do not use any fabric softener! Maximum load 2,5 kg Wash Rinses Short spin SPIN REDUCTION SPOELSTOP EXTRA SPOELEN 20 Min. - 3 kg 40° or 30° Quick wash of sport items or cotton and synthetic items, lightly soiled or worn once. Maximum load 3 kg Wash Rinses Short spin SPIN REDUCTION Super Eco 0° Mixed fabrics (cotton and synthetic items)8).
www.aeg.com 10) Set this programme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended. STEAM PROGRAMMES Programme1) Type of load Load Stoom Opfrissen2) This cycle removes odour from the laundry. Cotton and synthetic items. up to 1.5 Kg Cotton and synthetic items. up to 1.5 Kg Steam does not remove animal odours. Stoom Ontkreuk2) This programme helps to dewrinkle odour from the laundry.
ENGLISH 17 CONSUMPTION VALUES The data of this table are approximate. Different causes can change the data: the quantity and type of laundry, the water and ambient temperature. Programmes Load (Kg) Energy consumption (kWh) Water conApproxiRemaining sumption (li- mate promoisture tre) gramme du(%)1) ration (minutes) Cottons 60 °C 9 1.60 69 168 43 Cottons 40 °C 9 1.00 69 164 43 Synthetics 40 °C 4 0.60 48 105 35 Delicates 40 °C 4 0.70 58 86 35 Wool/Hand wash 30 °C 2 0.
www.aeg.com CLOCK SETTING After you set the language, the display tells to set the clock: • The hour digits flash. • Turn the programme knob to change the hour. • Touch button 6 to confirm the selection. • The minute digits flash. • Turn the programme knob to change the minutes. • Touch button 6 to confirm the selection. 2. 3. The hour digits flash. Turn the programme knob to change the hour. 4. Touch button 6 to confirm the selection. 5. The minute digits flash. 6.
ENGLISH If you put more laundry than the maximum load, the display tells that you put more than the maximum load. You can wash your laundry but the energy and water consumption increase. To have the best consumption and washing performance remove some items. The overload indication is available only for programmes with a maximum load lower than the appliance maximum load. 5. 19 Close the door. The text bar on the display tells the percentage of detergent to use.
www.aeg.com This is the maximum level for the quantity of liquid additives. The compartment for the stain remover. Put the product in the compartment and set the stain function before you start the programme. Flap for powder or liquid detergent Turn it (up or down) in the correct position to use powder or liquid detergent. Always obey the instructions that you find on the packaging of the detergent products. Check the position of the flap 1. Pull out the detergent dispenser until it stops. 2.
ENGLISH 5. 6. 21 Measure out the detergent and the fabric conditioner. Carefully close the detergent dispenser. Make sure that the flap does not cause a blockage when you close the drawer. SET THE DELAY START 1. Touch button 7 again and again to set the desired delayed start. The display shows the expected end of the programme 2. Touch button 6 , the appliance starts the countdown of the delay start. When the countdown is completed, the programme starts automatically.
www.aeg.com If the temperature and the level of the water is too high, the door lock symbol stays on. You cannot open the door. If necessary, do the following procedure to open the door: 1. Deactivate the appliance. 2. Wait for some minutes. 3. Make sure that no water is in the drum. If you deactivate the appliance, it is necessary to set the programme again. AT THE END OF PROGRAMME 1. 2. The appliance stops automatically. The acoustic signals operate, if it is active. 3.
ENGLISH 23 HELPFUL HINTS AND TIPS THE LAUNDRY LOAD DETERGENTS AND ADDITIVES • Divide the laundry in: white, coloured, synthetics, delicates and wool. • Obey the washing instructions that are on the laundry care labels. • Do not wash together white and coloured items. • Some coloured items can discolour with the first wash. We recommend that you wash them separately for the first times. • Button up pillowcases, close zippers, hooks and poppers. Tie up belts. • Empty the pockets and unfold the items.
www.aeg.com Level Type 2 Water hardness °dH °T.H. mmol/l Clarke medium 8-14 16-25 1.6-2.5 10-16 3 hard 15-21 26-37 2.6-3.7 17-25 4 very hard > 21 > 37 >3.
ENGLISH 25 CARE AND CLEANING WARNING! Disconnect the appliance from the mains supply before you clean it. DESCALING The water we use contains limescale. If it becomes necessary, use a water softener to remove limescales. Use a special product made for washing machines. Obey the instructions that you find on the packaging of the manufacturer. Do this separately from the laundry wash. EXTERNAL CLEANING CAUTION! Do not use alcohol, solvents or chemical products.
www.aeg.com DETERGENT DISPENSER To clean the dispenser: 1 1. 2. Press the lever. Pull the dispenser out. 3. Remove the top part of the liquid additive compartment. Clean all the parts with water. 2 4. 5. 6. DRAIN PUMP Regularly examine the drain pump and make sure that it is clean. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn. • The appliance makes an unusual noise because of the blockage of the drain pump.
ENGLISH 27 To clean the drain pump: 1. Open the drain pump door. 2. Pull the flap out to remove it. 3. Put a container below the recess of the drain pump to collect the water that flows out. Press the two levers and pull forward the drainage duct to let the water flow out. 4. 1 5. 6. When the container is full of water, put the drainage duct back again and empty the container. Do steps 4 and 5 again and again until no more water flows out from the drain pump.
www.aeg.com 9. Clean the filter under the water tap and put it back in the pump into the special guides. 10. Make sure that you tighten correctly the filter to prevent leakages. 11. Put the flap back and close the drain pump door. 2 1 THE INLET HOSE FILTER AND THE VALVE FILTER • The indicator of button 6 flashes and the display shows the related alarm. Refer to 'Troubleshooting'. WARNING! Disconnect the mains plug from the mains socket.
ENGLISH When you drain the water with the emergency drain procedure, you must activate again the drain system: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. FROST PRECAUTIONS If the appliance is installed in an area where the temperature can be less than 0 °C, remove the remaining water from the inlet hose and the drain pump. 1. Disconnect the mains plug from the mains socket. 2. Close the water tap. 3.
www.aeg.com TROUBLESHOOTING The start of the appliance does not occur or it stops during operation. Try to find a solution to the problem before you contact the service centre (refer to the table). With some problems, the acoustic signals operate and the display shows an alarm message. WARNING! Deactivate the appliance before you do the checks. Problem Possible cause Possible solution The display tells to check the tap: the appliance does not fill with water. The water tap is closed.
ENGLISH 31 PROBLEM WITHOUT ALARM MESSAGE Problem Possible cause Possible solution The appliance does not drain the water. A washing programme without the drain phase is set. Set the drain programme. The function Rinse Hold is on. Set the drain programme. The spin phase The spin phase is off. does not operate. The programme does not start. Set the spin programme. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'.
www.aeg.com Problem Possible cause Possible solution You did not remove the packaging and/or the transit bolts. Remove the packaging and/or the transit bolts. Refer to 'Installation'. The load is very small. Add more laundry in the drum. The appliance fills The end of the drain with water and hose is too low. drain immediately. Make sure that the drain hose is in the correct position. The washing reThe detergent you used sults are not satis- was not sufficient or corfactory. rect.
ENGLISH 33 INSTALLATION FIXING PLATE KIT (405517114) Available from your authorized dealer. If you install the appliance on a plinth, secure the appliance in the fixing plates. Follow the instructions supplied with the kit. UNPACKING 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film.
www.aeg.com 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. 8. Fully clean and dry the bottom of the appliance. Do not use alcohol, solvents or chemical products.
ENGLISH 9. A 35 Make sure to identify the different sizes and the positions of the sound barriers. Refer to the illustration: A (FRONT) = Front of the appliance B (BACK) = Rear of the appliance B 10. – Remove the adhesive strip from x4 A the silent barriers. – Attach the four barriers to bottom of the appliance. Refer to the illustration. – Make sure that the barriers are securely attached. Attach the sound barriers at a room temperature. B 11. Pull up the appliance in vertical posi- tion. 12.
www.aeg.com 13. Turn the three bolts with the key sup- plied with the appliance. Pull out the plastic spacers. 14. Put the plastic caps in the holes. You can find these caps in the user manual bag. WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance. POSITIONING AND LEVELLING • Install the appliance on a flat hard floor.
ENGLISH 37 • The appliance must be level and stable. CAUTION! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level. THE INLET HOSE • Connect the hose to the appliance. Turn the inlet hose only left or right. Loose the ring nut to set it in the correct position. 20 O 45 O • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings.
www.aeg.com Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault . If this occur, close the water tap and contact the service centre to replace the hose. A WATER DRAINAGE There are different procedures to connect the drain hose: With the plastic hose guide. • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains.
ENGLISH 39 Without the plastic hose guide. • To a sink spigot. Refer to the illustration. Put the drain hose in the spigot and tighten it with a clip. Make sure that the drain hose makes a loop to prevent that remaining particles go in the appliance from the sink. • Directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension.
www.aeg.