L 98699 FL2 EN User manual
www.aeg.com CONTENTS 1. 2. 3. 5. 7. 8. 9. 15. 16. 17. 18. 19. 20. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use, read this manual carefully: • For your safety and the safety of your property • To help the environment • For the correct operation of the appliance. Always keep these instructions with the appliance also if you move or give it to a different person. The manufacturer is not responsible if an incorrect installation and use causes damage. 1.
www.aeg.com To replace the internal lamp, contact the service centre. Disconnect the mains plug from the mains socket before the replacement of the internal lamp. 1.6 Installation • The appliance is heavy, be careful when you move it. • Do not transport your appliance without the transit bolts, you can damage internal components and cause leakages or malfunctions. • Do not install and connect a damaged appliance. • Make sure to remove all packaging and transport bolts.
ENGLISH Electrical connection: Voltage Overall power Fuse Frequency 230 V 2200 W 10 A 50 Hz Level of protection against ingress of solid particles and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture Water supply pressure 5 IPX4 Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Cold water Water supply 1) Maximum load Cotton 9 kg Spin speed Maximum 1600 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread.
www.aeg.com 4. INTERIOR ACCESSORIES 1 1 Spanner 2 To remove the transit bolts. 2 Plastic caps 5 4 To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Sound barrier To decrease the noise while the appliance operates. 4 Plastic hose guide To connect the drain hose on the edge of a sink. 5 Anti-flood inlet hose To prevent possible leakage. 3 5. CONTROL PANEL 1 2 Damp Krøludglatning Damp Genopfriskning Energispare Super Eco 20 Min.
ENGLISH 6.1 TOUCH SCREEN Do not wear gloves when you touch the buttons. Make sure the touch screen and buttons are always clean and dry. 6.2 AUTO Off button 1 Press this button to activate or deactivate the appliance. A tune sounds when the appliance is activated. The AUTO OFF function automatically deactivates the appliance to stop the energy consumption when: • You do not use the appliance for 5 minutes before you press button 6 . – All settings are cancelled.
www.aeg.com • The time of the day When you activate the appliance the display shows the time of the day for some seconds. To adjust the clock, refer to "Clock setting". • The programme duration When the washing programme starts, the programme time decreases every minute. Programme duration symbol The symbol comes on when the digits shows the programme duration. D • The end time of the washing programme . Programme end symbol The symbol comes on when the digits shows the programme end time.
ENGLISH 9 Extra rinsing G The indicator bar fills accordingly the numbers of rinses. Stains Prewash H Soak The indicator bar fills accordingly to the set functions. The default spin speed of the programme. I ___ No spin 1) Rinse hold 1) Only available for Spin/Drain programme. The default temperature of the programme. J Cold wash 6.5 BUTTON DAMP 4 2. Touch button 4 to set the steam level. This is possible only with programmes where the steam function is available.
www.aeg.com Some programmes accept only one of these functions. 6.10 BUTTON EKSTRA SKYLL 9 Set this function to prevent fabric creases. The appliance does not drain the water when the programme is completed. 6.13 TEMPERATURE BUTTON Touch button 9 to add rinsing phases to a programme. Use this function for persons allergic to detergents and in areas where the water is soft. 6.
ENGLISH • To activate the function touch button 8 and button 7 at the same time until the display shows the symbol . 11 • To deactivate the function touch button 8 and button 7 at the same time until the symbol goes off. 7. WASHING PROGRAMMES Programme Temperature Type of load Weight of load Programme description Functions Koke-/Kulørt 95° - Cold White and coloured cotton with heavy level of soil.
www.aeg.com Programme Temperature Type of load Weight of load Ull/Silke 40° - Cold Rinses Short spin Machine washa- Wash ble wool as well Rinses as for hand wash- Short spin able woollens and delicate fabrics with «hand washing» care symbol. Maximum load 2 kg Spin Reduction Skillestop Sengeteppe 60° - 30° Rinses Short spin Special proWash gramme for one Rinses synthetic blanket, Short spin duvet, bedspread and so on. Maximum load 3 kg Spin Reduction Antiallergi 60° White cotton items.
ENGLISH Programme Temperature 13 Type of load Weight of load Programme description Functions 20 Min. - 3 kg 40° or 30° Quick wash of sport items or cotton and synthetic items, lightly soiled or worn once. Maximum load 3 kg Wash Rinses Short spin Spin Reduction Super Eco 0° Mixed fabrics (cotton and synthetic items)8). Maximum load 3 kg Wash Rinses Long spin Spin Reduction Skillestop Ekstra skylling Energisparing 60° or 40° White and fast coloured cotton with the normal soil10).
www.aeg.com Cotton and synthetic items. Damp Oppfriskning2) This cycle removes odour from the laundry. up to 1.5 Kg Steam does not remove animal odours. Cotton and synthetic items. Damp Antikrøll2) This programme helps to dewrinkle the laundry. up to 1.5 Kg Steam can be used for dried, washed or worn once laundry. These programmes can reduce creases and odours and make your laundry more smooth. Do not use any detergent. If necessary, remove stains by washing or using localized stain removal.
ENGLISH Programmes Load (Kg) Energy con- Water consumption sumption (li(kWh) tre) 15 Approximate programme duration (minutes) Remaining moisture (%)1) Cottons 60 °C 9 1.60 69 168 43 Cottons 40 °C 9 1.00 69 164 43 Synthetics 40 °C 4 0.60 48 105 35 Delicates 40 °C 4 0.70 58 86 35 Wool/Hand wash 30 °C 2 0.35 57 56 30 Standard cotton programmes Standard 60 °C cotton 9 0.90 65 233 43 Standard 60 °C cotton 4.5 0.58 40 198 43 Standard 40 °C cotton 4.5 0.
www.aeg.com 8.2 Clock setting After you set the language, the display tells to set the clock: • The hour digits flash. • Turn the programme knob to change the hour. • Touch button 6 to confirm the selection. • The minute digits flash. • Turn the programme knob to change the minutes. • Touch button 6 to confirm the selection. 2. 3. The hour digits flash. Turn the programme knob to change the hour. 4. Touch button 6 to confirm the selection. 5. The minute digits flash. 6.
ENGLISH 17 11. LOADING THE LAUNDRY Open the appliance door. The display (E) shows the maximum programme load for the programme (MAX ) and the weight of the laundry (KG). The text bar on the display tells to add the laundry. 3. Put the laundry in the drum, one item at a time. Shake the items before you put them in the appliance. 4. On the display the weight of the laundry updates by step of kg 0.5. The weight is indicative and changes with the type of the laundry. 1. 2. 5. Close the door.
www.aeg.com 12. FILLING THE DETERGENT AND ADDITIVES The detergent compartment for the prewash phase and the soak programme. Add the detergent for prewash and soak before the start of the programme. The detergent compartment for the washing phase. If you use a liquid detergent, put it immediately before you start the programme. Liquid additives compartment (fabric conditioner, starch). Put the product in the compartment before you start the programme.
ENGLISH 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down. 19 With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6. Measure out the detergent and the fabric conditioner. Carefully close the detergent dispenser.
www.aeg.com The appliance adjust automatically the cycle time to the laundry you have put in the drum to have perfect washing results in the minimum necessary time. After approximately 15 minutes from the start of the programme, the display shows the new time value. 2. 3. Change the function set. Touch button 6 again. The washing programme continues. 14.4 Open the door While a programme or the delay start operates, the appliance door is locked. To open the appliance door: 1. 14.
ENGLISH The washing programme is completed, but there is water in the drum: – The drum turns regularly to prevent the creases in the laundry. – The door stays locked. – You must drain the water to open the door. To drain the water: 1. If necessary, decrease the spin speed. 21 2. Touch button 6 . The appliance drains the water and spins. 3. When the programme is completed and the door lock symbol goes off, you can open the door 4. Press button 1 to deactivate the appliance.
www.aeg.com chines. In areas where the water hardness is soft it is not necessary to use a water softener. To know the water hardness in your area, contact your local water authority. Obey the instructions that you find on the packaging of the products. Equivalent scales measure the water hardness: • German degrees (°dH). • French degrees (°TH). • mmol/l (millimol for each litre - international unit for the hardness of water). • Clarke degrees. Water hardness table Level Type Water hardness °dH °T.
ENGLISH 23 17.4 Door seal Regularly examine the seal and remove all objects from the inner part. 17.5 Drum Regularly examine the drum to prevent limescale and rust particles. Only use special products to remove rust particles from the drum. To do this: • Clean the drum with special product for stainless steel. • Start a short programme for cotton at the maximum temperature with a small quantity of detergent. 17.6 Detergent dispenser To clean the dispenser: 1 1. 2. Press the lever.
www.aeg.com 17.7 Drain pump Regularly examine the drain pump and make sure that it is clean. • The display shows an alarm code because of the problem with water drain. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates. Do not clean the drain pump if the water in the appliance is hot. The water must be cold before you clean the drain pump. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn.
ENGLISH 2 1 17.8 The inlet hose filter and the valve filter 7. Remove fluff and objects from the pump. 8. Make sure that the impeller of the pump can turn. If this does not occur, contact the service centre. 25 9. Clean the filter under the water tap and put it back in the pump into the special guides. 10. Make sure that you tighten correctly the filter to prevent leakages. 11. Put the flap back and close the drain pump door.
www.aeg.com 4. 5. 6. 7. 20° Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 45° 17.9 Emergency drain Because of a malfunction, the appliance cannot drain the water. If this occurs, do steps (1) through (6) of 'To clean the drain pump'. If necessary, clean the pump. Put the drainage duct back and close the drain pump flap.
ENGLISH Problem Possible cause The display tells The water tap is closed. to check the tap: the appliance does not fill with water. 27 Possible solution Open the water tap. The water inlet hose is damaged. Make sure that the water inlet hose has no damages. The filters in the water inlet hose is blocked . Clean the filters. Refer to 'Care and cleaning'. The connection of the water inlet hose is not correct. Make sure that the connection is correct. The water pressure is too low.
www.aeg.com Problem Possible cause Possible solution The spin phase does not operate. The spin phase is off. Set the spin programme. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again. The mains plug is not connected in the mains socket. Put in the mains plug. Blow out fuse in the household fuse box. Replace the fuse.
ENGLISH 29 Problem Possible cause The washing results are not satisfactory. The detergent you used Increase the detergent quantity was not sufficient or cor- or use a different one. rect. Possible solution You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains. You set a not correct temperature. Make sure that you set the correct temperature. Too much laundry load. Decrease the laundry load. The internal lamp The lamp is burned.
www.aeg.com 19.2 Unpacking 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum.
ENGLISH 31 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. 8. Fully clean and dry the bottom of the appliance. Do not use alcohol, solvents or chemical products. 9. Make sure to identify the different sizes and the positions of the sound barriers.
www.aeg.com 10. – Remove the adhesive strip from x4 A the silent barriers. – Attach the four barriers to bottom of the appliance. Refer to the illustration. – Make sure that the barriers are securely attached. Attach the sound barriers at a room temperature. B 11. Pull up the appliance in vertical po- sition. 12. Remove the power supply cable and the drain hose from the hose holders. 13. Turn the three bolts with the key supplied with the appliance. Pull out the plastic spacers.
ENGLISH 33 14. Put the plastic caps in the holes. You can find these caps in the user manual bag. WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance. 19.3 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance.
www.aeg.com 19.4 The inlet hose • Connect the hose to the appliance. Turn the inlet hose only left or right. Loose the ring nut to set it in the correct position. 20 O 45 O • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device.
ENGLISH 35 With the plastic hose guide. • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose.
www.aeg.com You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension. 20. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste.
ENGLISH 37
www.aeg.
ENGLISH 39
132924740-A-162012 www.aeg.