EN User Manual Washer Dryer L 99695 HWD
www.aeg.com CONTENTS 1. SAFETY INFORMATION.................................................................................................3 2. SAFETY INSTRUCTIONS................................................................................................ 5 3. PRODUCT DESCRIPTION.............................................................................................. 7 4. CONTROL PANEL...........................................................................................................8 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • • • • • • • • • • • • • side, where the appliance door can not be fully opened. Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. The ventilation openings in the base (if applicable) must not be obstructed by a carpet. Ensure you have good ventilation in the installation room to avoid the back flow of gases into the room from appliances burning other fuels, including open fires.
ENGLISH • • • • • • • • 5 Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the wash dryer. Fabric softeners, or similar products, should be used as specified by the fabric softener instructions. Remove all objects from pockets such as lighters and matches.
www.aeg.com 2.2 Electrical Connection WARNING! Risk of fire and electrical shock. • The appliance must be earthed. • Always use a correctly installed shockproof socket. • Do not use multi-plug adapters and extension cables. • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • Do not touch the mains cable or the mains plug with wet hands. • Only for UK and Ireland: The appliance has a 13 amp mains plug.
ENGLISH 3. PRODUCT DESCRIPTION 3.1 Appliance overview 1 2 3 10 4 11 12 5 6 13 7 9 8 1 2 3 4 5 6 7 8 Worktop Detergent dispenser Air filter(s) Control panel Door handle Rating plate Drain pump filter Feet for the appliance level 3.2 How to activate the child safety device This device prevents children or pets to be closed in the drum. Turn the device clockwise, until the groove is horizontal. You cannot close the door.
www.aeg.com 3.3 Accessories 1 2 4 3 1 Spanner To remove the transit bolts. 2 Plastic caps To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Inlet Hose To connect the appliance to the water tap. 4 Plastic hose guide To connect the drain hose on the edge of a sink. 4. CONTROL PANEL 4.
ENGLISH 4.2 Display A K J B I H G C F D E The display shows: A The text bar: • Guides you in the use of the appliance. • Shows the programme status and phase. • Shows alarm messages. Refer to 'Troubleshooting' . The symbols appear on the display when the related phase or function is set. B Child safety lock Door locked C You cannot open the appliance door when the symbol is on. You can open the door only when the symbol goes off.
www.aeg.com Digit area Time of the day When you activate the appliance the display shows the time of the day for some seconds. To adjust the clock, refer to "Clock setting". Programme duration When you set the programme, the cycle duration is displayed for a few seconds then, the time of the programme end appears again. Programme duration indicator The indicator comes on when the digits shows the programme duration.
ENGLISH Time save The indicator comes on when you set one of the programme duration. F Shortened time Extra Quick G Indicator for air filters Extra rinsing H The value shows the total number of the rinses. The indicator bar fills accordingly the numbers of rinses. Stain indicator Prewash indicator I Soak indicator The indicator bar fills accordingly to the set functions. Spin speed of the set programme J No Spin indicator1) Rinse Hold indicator 1) Only available for SPIN/DRAIN programme.
www.aeg.com 5. PROGRAMMES 5.1 Programme Chart Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) Washing/Drying programmes1) Cottons 95°C - Cold Cottons Eco2) 60°C - 40°C Synthetics 60°C - Cold Wool/Silk 40°C - Cold Anti-Allergy 60°C 9 kg 1600 rpm White cotton and coloured cotton. Normal soil and light soil. 9 kg 1600 rpm White cotton and colour-fast cotton. Normal soil.
ENGLISH Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) Super Eco Cold 3 kg 1200 rpm Mixed fabric (cotton and synthetic items).5) 20 Min. - 3 Kg 40°C - 30°C 3 kg 1200 rpm Cottons and synthetics items with light soil level or worn only once. 9 kg 1600 rpm To rinse and spin the laundry. All fabrics. 9 kg 1600 rpm To spin the laundry and to drain the water in the drum. All fabrics.
www.aeg.com Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) up to 1.5 kg Steam programme for cotton and synthetic items. This cycle removes odours from the laundry.9) Refresh 40°C 1) When you set a Washing / Drying programme, the display tells you that the drying cycle is not set. If you want to dry your laundry, set an automatic drying or a timed drying.
ENGLISH 15 ■ Easy Iron ■ ■ ■ ■ Super Eco ■ ■ 20 Min. - 3 Kg ■ Rinse ■ Spin/Drain ■ ■ Delay Start ■ Time Save2) ■ Extra Rinse 1) ■ Soak Stains Delicates Spin Prewash Programme ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) If the Permanent Extra Rinse option is activated, the appliance adds some additional rinses. In the Rinse programme, if you set a low spin speed the appliance performs delicate rinses and a short spin.
www.aeg.com 5.
ENGLISH 17 6. CONSUMPTION VALUES The data of this table are approximate. Different causes can change the data: the quantity and type of laundry, the water and ambient temperature. At programme start the display shows the duration programme for the maximum load capacity. During the washing phase the programme duration is automatically calculated and can be greatly reduced if the laundry load is lower than the maximum load capacity (e.g.
www.aeg.com the same time until the indicator comes on/goes off. You can activate this function: • After you touch Start/Pause : all the buttons and the programme knob are deactivated. • Before you touch Start/Pause : the appliance cannot start. • To activate/deactivate this function touch Time Save and Delay Start at the same time until the display show the indicator off. comes on/goes 7.
ENGLISH 8.7 Start/Pause • Soak Use this function for heavy soil. The appliance soaks the laundry at 30°C for about half an hour before to wash. • Stains Use this function for laundry with hard stains to remove. When you set this function, put the stain remover into Touch button Start/Pause to start or interrupt a programme. 8.8 Delay Start Touch button Delay Start to delay the start of a programme from 30 minutes to 20 hours. 8.9 Time Save Touch button Time Save to decrease the programme time.
www.aeg.com The minute digits flash. 3. Turn the programme knob to change the minutes. 4. Touch Start/Pause button to confirm the selection. 9.2 Change the time of the day after the first activation 1. Touch the button Extra Rinse and the button Time Save at the same time for some seconds. The hour digits flash. 2. Turn the programme knob to change the hour. 3. Touch Start/Pause button to confirm the selection. The minute digits flash. 4. Turn the programme knob to change the minutes. 5.
ENGLISH 21 Compartment for prewash phase, soak programme or stain remover. Compartment for washing phase. Compartment for liquid additives (fabric conditioner, starch). Maximum level for quantity of liquid additives. Flap for powder or liquid detergent. Always obey the instructions that you find on the packaging of the detergent products. CAUTION! Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. 10.
www.aeg.com B 4. 3. • Position A for powder detergent (factory setting). • Position B for liquid detergent. When you use the liquid detergent: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid then the maximum level. • Do not set the prewash phase. • Do not set the delay start. 10.6 Starting a programme without the delay start 10.8 Starting a programme with the delay start Touch button Start/Pause to start the programme.
ENGLISH 10.10 Interrupting a programme and changing the options You can change only some options before they operate: 1. Touch button Start/Pause. The related indicator flashes. 2. Change the options. 3. Touch button Start/Pause again. The washing programme continues. 10.11 Cancelling a running programme 1. Press button On/Off to cancel the programme and to deactivate the appliance. 2. Press button On/Off again to activate the appliance. Now, you can set a new washing programme.
www.aeg.com 11. END OF THE PROGRAMME When the programme has finished, the appliance stops automatically. The acoustic signal operates (if it is active). In the display comes on and a message tells you that the programme is completed. The indicator of Start/Pause button goes off. 1. Press the button On/Off to deactivate the appliance. After five minutes from the end of the programme, the energy saving function automatically deactivates the appliance.
ENGLISH The display shows 15 minutes for cottons and synthetics programmes while starts from 13 minutes for wool programme. Each time you touch this button the time value increases by 5 minutes. The display shows the set time value. 2. Touch Start/Pause to start the programme. The text bar tells that the appliance is drying. On the display appear the door locked and the programme in progress indicators. The display shows alternatively, the drying cycle duration and the time of the cycle end.
www.aeg.com indicator and, alternatively, the drying time and the time of the cycle end. The text bar tells that the appliance is operating. The display shows regularly a new time value. 13.3 Washing and Timed Drying 1. Touch button Time Dry repeatedly to set the time value (see the «Drying Programme» table). The display shows 15 minutes for cottons and synthetics programmes while starts from 13 minutes for wool programme. Each time you press this button the time value increases by 5 minutes.
ENGLISH • Remove hard stains. • Wash with a special detergent heavy soil stains. • Be careful with the curtains. Remove the hooks or put the curtains in a washing bag or pillowcase. • Do not wash in the appliance laundry without hems or with cuts. Use a washing bag to wash small and/or delicate items (e.g. underwired bras, belts, tights, etc. ). • A very small load can cause balance problems with the spin phase. If this occurs, adjust manually the items in the tub and start the spin phase again.
www.aeg.com • Fabrics with residue of hair sprays, nail solvents or similar. • Garments with foam-rubber or materials similar to foam-rubber. 14.8 Garment labels When you dry the laundry, obey the indications on the labels of the manufacturers: • = The item can be tumble dried • = The drying cycle is at high temperature • = The drying cycle is at reduced temperature • = The item can not be tumble dried. 14.
ENGLISH • Set the cotton programme with the highest temperature with a small quantity of detergent. Regularly examine the seal and remove all objects from the inner part. 15.4 Door seal 15.5 Cleaning the detergent dispenser 1. 2. 1 2 3. 29 4.
www.aeg.com 15.6 Cleaning the air filters The air filters collect the fluff. The fluff normally occurs when the clothes are dried in a washer-dryer. • At the end of each drying cycle in the display the indicator the primary air filter. The text bar says to clean the primary filter (see pict. 1-5). is on to tell you to clean may flash to remind you that both air filters should be • Occasionally the indicator cleaned.
ENGLISH + 10. 9. To have best drying performances clean regularly the air filters with warm water and afterwards dry them with a towel. Clogged filter increases the drying time. WARNING! The primary filter recess must not be blocked by any object. If you only wash the laundry with your washer-dryer, it is normal to find some humidity in the primary air filter. 15.7 Cleaning the drain filter WARNING! Do not clean the drain filter if the water in the appliance is hot. 1. 2.
www.aeg.com 3. 4. 1 5. 2 6. 1 2 7. 8. 1 2 9.
ENGLISH 33 15.8 Cleaning the inlet hose filter and the valve filter It could be necessary to clean the filters when: • The appliance does not fill with water. • The appliance fills with the water for a long time. • The indicator of button Start/Pause flashes and the display shows the related alarm. Refer to 'Troubleshooting'. To clean the water inlet filters: • Close the water tap. • Remove the water inlet hose from the water tap. • Clean the filter in the inlet hose with a stiff brush.
www.aeg.com 15.9 Emergency drain Because of a malfunction, the appliance cannot drain the water. If this occurs, do steps (1) through (9) of 'Cleaning the drain filter'. If necessary, clean the pump. When you drain the water with the emergency drain procedure, you must activate again the drain system: 1. When you drain the water with the emergency drain procedure, you must activate again the drain system: Put 2 litres of water in the main wash compartment of the detergent dispenser. 2.
ENGLISH Message 35 Possible solution Make sure that the water tap is not clogged or is furred with lime-scale. Make sure that the filter of the inlet hose and the filter of the valve are not clogged. Refer to “Care and cleaning”. Make sure that the inlet hose is not damaged. Make sure that the connection of the water inlet hose is correct. The display tells to check the Make sure that the drain hose is not damaged. drain filter: the appliance does not drain the water.
www.aeg.com Problem Possible solution If the delay start is set, cancel the setting or wait for the end of countdown. Deactivate the Child Lock function if it is on. The appliance does not drain Make sure that you have not set a programme without the water. drain phase. Make sure that you have not set an option which ends with water in the tub. The appliance fills with water Make sure that the drain hose is in the correct position. and drains immediately. The hose may be too low.
ENGLISH Problem Possible solution The washing results are not satisfactory. Increase the detergent quantity or use a different detergent. 37 Use special products to remove the stubborn stains before you wash the laundry. Make sure that you set the correct temperature. Decrease the laundry load. The washing cycle is shorter than the time displayed. The appliance calculates a new time according to the laundry load. The washing cycle is longer than the time displayed.
www.aeg.com 16.3 Emergency door opening To open the door, proceed as follows: In case of power failure or appliance failure the appliance door remains locked. The washing programme continues, when the power is restored. If the door remains locked in case of failure, it is possible to open it using the emergency unlock feature. 1. Press the button On/Off to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4.
ENGLISH 39 Use the gloves. • Remove the external film. If necessary, use a cutter • Remove the cardboard top. • Remove the polystyrene packaging materials. • Remove the internal film. • Open the door. • Remove the polystyrene piece from the door seal and all the items from the drum. • Put one of the polystyrene packaging elements on the floor behind the appliance. • Carefully put down the appliance with the rear side on it. • Make sure not to damage the hoses.
www.aeg.com • Remove the polystyrene protection from the bottom. 1 2 • Pull up the appliance in vertical position. • Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliances in factory. • Remove the three bolts. • Use the key supplied with the appliance. • Pull out the plastic spacers.
ENGLISH 41 • Put the plastic caps in the holes. • You can find these caps in the user manual bag. We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 17.2 Fixing plate kit (4055171146) Available from your authorized dealer. If you install the appliance on a plinth, secure the appliance in the fixing plates. Read carefully the instructions supplied with the accessory.
www.aeg.com 17.5 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units. • Loosen or tighten the feet to adjust the level. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. x4 • The appliance must be level and stable.
ENGLISH 43 • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. 17.7 Water drainage There are different procedures to connect the drain hose: With the plastic hose guide: • Making an U form with the drain hose.
www.aeg.com Drain hose end • If the end of the drain hose looks like this (see the picture), you can push it directly into the stand pipe. Without the plastic hose guide. To a sink spigot • Refer to the illustration. Put the drain hose in the spigot and tighten it with a clip. • Make sure that the drain hose makes a loop to prevent that remaining particles go in the appliance from the sink. To a wall-pipe • Directly to a built-in drain pipe in the room wall and tighten it with a clip.
ENGLISH 2) Water supply pressure Minimum Maximum 0,5 bar (0,05 MPa) 8 bar (0,8 MPa) Ambient temperature Minimum 5 °C Maximum 35 °C Cotton 9 Synthetics 4 Wool 1.5 Cotton 6 Synthetics 4 Wool 1 Maximum 1600 rpm Maximum wash load Maximum dry load Spin Speed 45 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 2) The appliance works correctly if the water pressure is not less than 0.05 MPa (0.5 bar).
www.aeg.
ENGLISH 47
132908863-A-062015 www.aeg.