DE Benutzerinformation Wasch-Trockner L 99699 HWD
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.................................................................................. 4 2. SICHERHEITSANWEISUNGEN...................................................................................... 7 3. GERÄTEBESCHREIBUNG...............................................................................................9 4. BEDIENFELD................................................................................................................. 10 5.
DEUTSCH Änderungen vorbehalten.
1. www.aeg.com SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Sicherheit von Kindern und schutzbedürftigen Personen WARNUNG! Erstickungs- und Verletzungsgefahr sowie Gefahr einer dauerhaften Behinderung.
DEUTSCH • • • • • • • • • • 5 Das Gerät kann freistehend oder unter einer Küchenarbeitsplatte in einer Nische mit den entsprechenden Abmessungen montiert werden. Das Gerät darf nicht hinter einer verschließbaren Tür, einer Schiebetür oder einer Tür mit einem Scharnier, das dem des Gerätes gegenüber liegt und eine vollständige Öffnung der Gerätetür verhindert, aufgestellt werden. Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose.
www.aeg.com • • • • • • • • • • • • Wischen Sie die um das Gerät ggf. angesammelten Flusen weg. Benutzen Sie das Gerät nie ohne Filter. Reinigen Sie den Flusenfilter vor oder nach jedem Gebrauch. Wäschestücke, die mit Speiseöl verschmutzt sind oder die mit Aceton, Alkohol, Kerosin, Fleckentfernern, Terpentin und Wachsentfernern behandelt worden sind, müssen vor dem Trocknen im Wasch-Trockner in heißem Wasser und zusätzlichem Waschmittel gewaschen werden.
DEUTSCH • 7 Reinigungsschwämmchen, Lösungsmittel oder Metallgegenstände. Schalten Sie das Gerät immer aus und ziehen Sie den Netzstecker aus der Steckdose, bevor Reinigungsarbeiten durchgeführt werden. 2. SICHERHEITSANWEISUNGEN 2.1 Montage • Entfernen Sie die Verpackungsmaterialien und die Transportschrauben. • Bewahren Sie die Transportschrauben auf. Wenn Sie das Gerät umsetzen, müssen Sie die Trommel blockieren. • Seien Sie beim Umsetzen des Geräts vorsichtig, denn es ist schwer.
www.aeg.com 2.4 Gebrauch WARNUNG! Verletzungs-, Stromschlag-, Brand-, Verbrennungsgefahr sowie Risiko von Schäden am Gerät. • Das Gerät ist ausschließlich für die Verwendung im Haushalt vorgesehen. • Nehmen Sie keine technischen Änderungen am Gerät vor. • Platzieren Sie keine entflammbaren Produkte oder Gegenstände, die mit entflammbaren Produkten benetzt sind, im Gerät, auf dem Gerät oder in der Nähe des Geräts. • Berühren Sie während des Betriebs nicht das Türglas. Das Glas kann sehr heiß sein.
DEUTSCH 3. GERÄTEBESCHREIBUNG 3.1 Geräteübersicht 1 2 3 10 4 11 12 5 6 13 7 9 8 1 2 3 4 5 6 7 8 Arbeitsplatte Waschmittelschublade Luftfilter Bedienfeld Türgriff Typenschild Filter der Ablaufpumpe Schraubfüße zum Ausrichten des Geräts 14 9 10 11 12 13 14 Luftschlitze Wasserablaufschlauch Wassereinlassventil Netzkabel Transportschrauben Schraubfüße zum Ausrichten des Geräts 3.
www.aeg.com 3.3 Zubehör 1 • Schraubenschlüssel: zum Lösen der Transportschrauben. • Kunststoffkappen: zum Verschließen der Öffnungen auf der Rückseite des Geräts nach dem Entfernen der Transportschrauben. • Schallschutzteile: zur Minderung der Geräuschbelastung während des Gerätebetriebs. • Kunststoff-Schlauchführung: zum Einhängen des Ablaufschlauchs an einer Waschbeckenkante. • Aqua-Safe-Zulaufschlauch: zur Verhinderung von eventuellen Wasserlecks. 2 5 4 3 4. BEDIENFELD 4.
DEUTSCH 12 Sensortaste Drehzahlreduzierung (U./ Min.) 11 13 Sensortaste Temperatur (Temp.) 4.2 Display A K J B I H G C F D E Im Display wird folgendes angezeigt: A Die Textzeile: • Hilft Ihnen bei der Benutzung des Geräts. • Informiert Sie über den Programmstatus und die Programmphase. • Zeigt Fehlermeldungen an. Siehe hierzu „Fehlersuche“. Die Symbole erscheinen im Display, wenn die zugehörige Programmphase oder Funktion eingestellt ist.
www.aeg.com Zahlenbereich Uhrzeit Wenn Sie das Gerät einschalten, zeigt das Display einige Sekunden lang die Uhrzeit an. Informationen zur Änderung der Uhrzeit finden Sie unter „Einstellen der Uhrzeit“. Programmdauer Wenn Sie das Programm einstellen, wird die Programmdauer einige Sekunden lang angezeigt, danach erscheint wieder die Endzeit des Programms. Anzeige Programmdauer Die Anzeige erscheint, sobald die Ziffern die Programmdauer anzeigen.
DEUTSCH 13 Zeit sparen Die Anzeige leuchtet auf, wenn Sie die Programmdauer einstellen. F Verkürzte Programmdauer Extra Kurz G Anzeige für Luftfilter Extra Spülen H Die Zahl steht für die Gesamtzahl der Spülgänge. Der Anzeigebalken füllt sich entsprechend der Anzahl der Spülgänge. Anzeige Flecken Anzeige Vorwäsche I Anzeige Einweichen Der Anzeigebalken füllt sich entsprechend der eingestellten Funktionen.
www.aeg.com 5. PROGRAMME 5.1 Programmübersicht Programm Temperaturbereich Maximale Bela- Programmbeschreibung dung (Beladung und Verschmutzungsgrad) Maximale Schleuderdrehzahl Wasch-/Trockenprogramme1) Koch/Bunt 95 °C - Kalt Baumwolle Eco2) 60 °C - 40 °C Pflegeleicht 60 °C - Kalt Wolle/Seide 40 °C - Kalt Anti-Allergie 60 °C 9 kg 1600 U/min Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. 9 kg 1600 U/min Weiße und farbechte Baumwollwäsche. Normal verschmutzt.
DEUTSCH Programm Temperaturbereich 15 Maximale Bela- Programmbeschreibung dung (Beladung und Verschmutzungsgrad) Maximale Schleuderdrehzahl 4 kg 800 U/min Pflegeleichte Textilien, die sanft gewaschen wer- Super Eco Kalt 3 kg 1200 U/min Mischgewebe (Baumwolle und Synthetik).5) 20 Min. - 3 kg 40 °C - 30 °C 3 kg 1200 U/min Teile aus Baumwolle oder Synthetik, die leicht verschmutzt sind oder nur einmal getragen wurden. 9 kg 1600 U/min Spülen und Schleudern der Wäsche. Alle Gewebearten.
www.aeg.com Programm Temperaturbereich Maximale Bela- Programmbeschreibung dung (Beladung und Verschmutzungsgrad) Maximale Schleuderdrehzahl bis zu 1.5 kg Auffrischen 40 °C Dampfprogramm für Baumwolle und pflegeleichte Wäsche. Dieses Programm beseitigt Gerüche aus der Wäsche.9) 1) Wenn Sie ein Wasch-/Trockenprogramm einstellen, zeigt das Display an, dass das Trockenprogramm nicht eingestellt ist. Wenn Sie Ihre Wäsche trocknen möchten, wählen Sie ein Automatikprogramm oder ein Zeitprogramm.
DEUTSCH 17 Zeitvorwahl Zeit Sparen2) Extra Spülen 1) Einweichen Flecken U./Min. Vorwäsche Programm ■ ■ Anti-Allergie ■ ■ ■ ■ ■ Feinwäsche ■ ■ ■ ■ ■ ■ ■ Leichtbügeln ■ ■ ■ ■ ■ ■ ■ Super Eco ■ ■ 20 Min. - 3 kg ■ Spülen ■ Schleudern/Pumpen ■ Wolle/Seide ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) Ist die Funktion Extra Spülen eingeschaltet, führt das Gerät zusätzliche Spülgänge aus.
www.aeg.com 5.3 Programme für das zeitgesteuerte Trocknen Trockengrad Gewebetyp Beladung (kg) Extra Trocken Für Frotteewaren Baumwolle und Leinen (Bademäntel, Badetücher usw.) Schleu- Vorgeschladerdreh- gene Dauer zahl (U/ (Min.) min) 6 1600 240 - 250 3 1600 120 - 140 1 1600 50 - 60 6 1600 230 - 240 3 1600 110 - 130 1 1600 40 - 50 Schranktrocken Für Wäschestücke, die sofort in den Schrank kommen Baumwolle und Leinen (Bademäntel, Badetücher usw.
DEUTSCH 6. VERBRAUCHSWERTE Bei den in dieser Tabelle angegebenen Werten handelt es sich um Richtwerte. Folgende Faktoren können diese Werte verändern: Die Wäscheart und -menge, die Wasser- und Raumtemperatur. Am Programmstart zeigt das Display die Programmdauer für die maximale Beladung an. Während der Waschphase wird die Programmdauer automatisch berechnet und verringert sich möglicherweise beträchtlich, wenn die Wäsche weniger wiegt als die maximal zulässige Beladung.
www.aeg.com • Berühren Sie zum Ein-/Ausschalten dieser Funktion Temp. und U./Min. auch wenn Sie ein neues Programm einstellen. gleichzeitig, bis die Anzeige aufleuchtet/erlischt. Wenn Sie diese Funktion einschalten: • Berühren Sie zum Ein-/Ausschalten dieser Funktion Zeit Sparen und Zeitvorwahl gleichzeitig, bis die • Nachdem Sie Start/Pause berührt haben: sind alle Tasten und der Programmwahlschalter ausgeschaltet. • Bevor Sie Start/Pause berührt haben: kann das Gerät nicht starten.
DEUTSCH 21 • Berühren Sie diese Taste zur Einstellung der Dampfmenge. Diese Option ist nur bei Programmen mit vorhandener Dampffunktion möglich. Die Dauer der Dampfphase ändert sich entsprechend Ihrer Einstellung. Vorwäsche Verwenden Sie diese Funktion bei stark verschmutzter Wäsche. Das Gerät fügt vor dem Hauptwaschgang einen Vorwaschgang hinzu. Die Programmdauer verlängert sich entsprechend. • Einweichen Verwenden Sie diese Funktion bei stark verschmutzter Wäsche.
www.aeg.com 9. REINIGEN SIE VOR DEM ERSTEN GEBRAUCH 1. Geben Sie eine kleine Waschmittelmenge in das Waschmittelfach für die Hauptwäsche. 2. Stellen Sie ein Koch-/BuntwäscheProgramm mit der höchsten Temperatur ein und starten Sie das Programm mit leerer Trommel. So werden alle eventuellen Verunreinigungen aus Trommel und Bottich entfernt. 9.1 Einstellen der Uhrzeit Nach der Einstellung der Sprache werden Sie aufgefordert, die Uhrzeit einzustellen: Die Stundenziffern blinken. 1.
DEUTSCH Die Programmkontrolllampe leuchtet auf. Die Kontrolllampe der Taste Start/Pause blinkt rot. Das Display zeigt die StandardTemperatur und -Drehzahl und bei geöffneter Tür die für das Programm maximal erlaubte Füllmenge an (diese Informationen erlöschen, sobald Sie die Tür schließen). 3. Berühren Sie, falls notwendig, die Tasten Temp. und U./Min., um die Wassertemperatur und Schleuderdrehzahl zu ändern. 4.
www.aeg.com 10.5 Flüssigwaschmittel oder Waschpulver Maximaler Füllstand für flüssige Pflegemittel. Klappe für Waschpulver oder Flüssigwaschmittel. Halten Sie sich immer an die Anweisungen auf der Verpackung der Waschmittelprodukte. 1 A 2 1. 2. B 4. 3. • Position A für Waschpulver (Werkseinstellung). • Position B für Flüssigwaschmittel. Bei Verwendung von Flüssigwaschmitteln: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz.
DEUTSCH 10.7 Verhalten des Gerätes Etwa 15 Minuten nach dem Start des Programms: • Das Gerät stellt automatisch die Programmdauer für die Menge der eingefüllten Wäsche in der Trommel ein, um perfekte Waschergebnisse in kurzer Zeit zu erzielen. • Das Display zeigt die neue Dauer an. 10.8 Starten eines Programms mit Zeitvorwahl 1. Berühren Sie zur Einstellung der gewünschten Zeitvorwahl wiederholt die Taste Zeitvorwahl. Das Display zeigt das voraussichtliche Ende des Programms an. 2.
www.aeg.com • Die Tür bleibt verriegelt. • Sie müssen das Wasser abpumpen, um die Tür öffnen zu können: 1. Reduzieren Sie, falls erforderlich, die Schleuderdrehzahl. 2. Berühren Sie Taste Start/Pause. Das Gerät pumpt das Wasser ab und schleudert. 3. Wenn das Programm beendet ist und die Anzeige der Türverriegelung erlischt, können Sie die Tür öffnen. 4. Halten Sie Ein/Aus einige Sekunden gedrückt, um das Gerät auszuschalten. Nach etwa 18 Stunden pumpt das Gerät automatisch das Wasser ab und schleudert.
DEUTSCH 3. Drehen Sie den Programmwahlschalter auf das geeignete Trockenprogramm. Die Textzeile im Display zeigt das gewählte Programm an. Wenn Sie große Wäschemengen trocknen, achten Sie darauf, dass die Wäschestücke nicht eingerollt und gleichmäßig in der Trommel verteilt sind, um ein gutes Trockenergebnis zu erzielen. Zu Beginn eines Trockengangs (in den ersten 3 - 5 Min.) ist der Geräuschpegel möglicherweise etwas höher.
www.aeg.com • Die Kontrolllampe der Taste Start/ Pause erlischt. Das Türverriegelungssymbol erlischt. • Halten Sie die Ein/Aus-Taste einige Sekunden lang gedrückt, um das Gerät auszuschalten. 1. Nehmen Sie die Wäsche aus dem Gerät. 2. Vergewissern Sie sich, dass die Trommel leer ist. Einige Minuten nach Ende des Programms schaltet die Energiesparfunktion das Gerät automatisch aus. 13. TÄGLICHER GEBRAUCH - WASCHEN UND TROCKNEN WARNUNG! Siehe Kapitel Sicherheitshinweise. 13.
DEUTSCH 13.3 Waschen und zeitgesteuertes Trocknen 1. Berühren Sie die Taste Zeit Trocknen wiederholt, um die Trockenzeit einzustellen (siehe Tabelle „Trockenprogramme“). Das Display zeigt 15 Minuten bei Programmen für Baumwolle und Pflegeleichtes an und startet bei 13 Minuten für Wollprogramme. Durch jeden Tastendruck erhöht sich die Trockenzeit um 5 Minuten. Die eingestellte Trockenzeit erscheint auf dem Display. 2. Drücken Sie Start/Pause, um das Programm zu starten.
www.aeg.com • Wenden Sie mehrlagige Textilien, Wolle und bedruckte Wäschestücke vor dem Waschen. • Entfernen Sie hartnäckige Flecken. • Waschen Sie stark verschmutzte Bereiche mit einem speziellen Waschmittel. • Seien Sie vorsichtig mit Gardinen. Entfernen Sie die Haken, oder stecken Sie die Gardinen in einen Beutel oder Kopfkissenbezug. • Waschen Sie keine ungesäumten Wäschestücke und Wäschestücke mit Schnitten im Stoff in der Maschine.
DEUTSCH Sie bitte der Tabelle „Trockenprogramme“. 14.7 Wäschestücke, die nicht getrocknet werden sollen Stellen Sie kein Trockenprogramm für folgende Wäschearten ein: • Besonders empfindliche Gewebe. • Synthetikvorhänge. • Kleidungsstücke mit Metalleinsätzen. • Nylonstrümpfe. • Steppdecken. • Bettdecken. • Daunen. • Anoraks. • Schlafsäcke. • Gewebe mit Resten von Haarsprays, Nagellackentferner oder ähnlichen Lösungsmitteln. • Kleidungsstücke aus Schaumgummi oder ähnlichen schwammartigen Materialien. 14.
www.aeg.com • Nehmen Sie die Wäsche aus der Trommel. • Starten Sie ein Programm für Koch-/ Buntwäsche mit der maximalen Temperatur und einer kleinen Menge Waschmittel. empfehlen wir die Verwendung eines Entkalkers für Waschmaschinen. Überprüfen Sie regelmäßig, dass sich kein Kalk und keine Rostpartikel in der Trommel absetzen. Verwenden Sie zur Entfernung von Rost nur Spezialprodukte für Waschmaschinen. Führen Sie die Entkalkung nicht gleichzeitig mit einer Wäsche durch. 15.
DEUTSCH 15.6 Reinigen der Luftfilter Die Luftfilter halten Flusen zurück. Die Flusen entstehen, wenn die Wäsche in einem Wasch-Trockner getrocknet wird. • Am Ende eines jeden Trockenprogramms leuchtet im Display die Anzeige , um Sie darauf hinzuweisen, dass der Hauptluftfilter gereinigt werden muss. Die Textzeile zeigt an, dass der Hauptfilter gereinigt werden muss (siehe Abb. 1-5). , um Sie daran zu erinnern, dass beide Luftfilter • Gelegentlich blinkt die Anzeige gereinigt werden müssen.
www.aeg.com + 10. 9. Um beste Trockenergebnisse zu erzielen, reinigen Sie die Luftfilter regelmäßig mit warmen Wasser und trocknen Sie sie mit einem Handtuch. Durch verstopfte Filter verlängert sich die Trockenzeit. WARNUNG! Die Aussparung des Hauptfilters darf nicht durch Gegenstände blockiert werden. Wenn Sie in Ihrem Wasch-Trockner ausschließlich Wäsche waschen, kann sich im Hauptluftfilter Feuchtigkeit ansammeln. 15.
DEUTSCH 3. 4. 1 5. 2 6. 1 2 7. 8. 1 2 9.
www.aeg.com 15.8 Reinigen des Zulaufschlauchfilters und Ventilfilters Die Filter müssen in folgenden Fällen gereinigt werden: • Es läuft kein Wasser in das Gerät. • Das Wasser läuft sehr lange in das Gerät ein. • Die Kontrolllampe der Taste Start/Pause blinkt und im Display wird der entsprechende Alarm angezeigt. Siehe hierzu „Fehlersuche“. So reinigen Sie die Wasserzulauffilter: • Schließen Sie den Wasserhahn. • Entfernen Sie den Wasserzulaufschlauch vom Wasserhahn.
DEUTSCH 15.9 Notentleerung Das Gerät kann aufgrund einer Funktionsstörung das Wasser nicht abpumpen. In diesem Fall führen Sie die Schritte (1) bis (9) unter „Reinigen des Ablauffilters“ durch. Reinigen Sie bei Bedarf die Pumpe. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 1. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. 2.
www.aeg.com Meldung Mögliche Abhilfe Vergewissern Sie sich, dass der Wasserdruck der Wasserversorgung nicht zu niedrig ist. Diese Information erhalten Sie von Ihrem Wasserversorger. Vergewissern Sie sich, dass der Wasserhahn nicht verstopft und nicht mit Kalk zugesetzt ist. Überzeugen Sie sich, dass der Filter des Zulaufschlauchs und der Filter des Ventils nicht verstopft sind. Siehe „Reinigung und Pflege“. Vergewissern Sie sich, dass der Zulaufschlauch nicht beschädigt ist.
DEUTSCH 39 Probleme ohne Fehlermeldungen Problem Mögliche Abhilfe Das Programm startet nicht. Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. Vergewissern Sie sich, dass Sie Start/Pause berührt haben. Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab oder warten Sie, bis sie abgelaufen ist. Schalten Sie die Kindersicherung aus, falls sie eingeschaltet ist.
www.aeg.com Problem Mögliche Abhilfe Stellen Sie das Abpump- oder Schleuderprogramm ein, wenn sich noch Wasser in der Trommel befindet. Stellen Sie sicher, dass das Gerät mit Spannung versorgt wird. Das Problem kann durch eine Gerätestörung verursacht worden sein. Wenden Sie sich an den autorisierten Kundendienst. Wenn Sie die Tür öffnen müssen, lesen Sie sorgfältig „Öffnen der Tür im Notfall“. Das Gerät macht ungewöhnliche Geräusche. Stellen Sie sicher, dass das Gerät richtig ausgerichtet ist.
DEUTSCH Problem 41 Mögliche Abhilfe Vergewissern Sie sich, dass Sie das richtige Programm eingestellt haben. Stellen Sie gegebenenfalls erneut eine kurze Trockenzeit ein. Das Trockenprogramm dauert zu lang. Vergewissern Sie sich, dass die Luftfilter sauber sind. Achten Sie darauf, dass die Beladung nicht das für das eingestellte Programm angegebene Gewicht überschreitet. Vergewissern Sie sich, dass sich die Raumtemperatur im angegebenen Bereich befindet.
www.aeg.com Öffnen Sie die Tür folgendermaßen: 1. Schalten Sie das Gerät durch Drücken der Taste Ein/Aus aus. 2. Ziehen Sie den Netzstecker aus der Netzsteckdose. 3. Öffnen Sie die Filterklappe. 4. Drücken Sie den Auslöser für die Notfallentriegelung nach unten und öffnen Sie gleichzeitig die Gerätetür. 5. Nehmen Sie die Wäsche heraus und schließen Sie die Gerätetür. 6. Schließen Sie die Filterklappe. 17. MONTAGE WARNUNG! Siehe Kapitel Sicherheitshinweise. 17.
DEUTSCH 43 • Nehmen Sie die Karton-Abdeckung ab. • Entfernen Sie die StyroporVerpackungsteile. • Entfernen Sie die innere Folie. • Öffnen Sie die Tür. • Entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel. • Legen Sie eines der Styroporverpackungsteile hinter dem Gerät auf den Boden. • Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. • Achten Sie darauf, die Schläuche nicht zu beschädigen. • Entfernen Sie den Styroporschutz von der Geräteunterseite.
www.aeg.com • Reinigen Sie die Unterseite des Geräts und trocknen Sie sie ab. • Verwenden Sie keinen Alkohol, keine Lösungsmittel und keine Chemikalien. Sortieren Sie die verschiedenen Teile des Schallschutzes nach Größe und Position. Orientieren Sie sich an der Abbildung: • A (VORDERSEITE) = Vorderseite des Geräts • B (RÜCKSEITE) = Rückseite des Geräts A B x4 • Entfernen Sie den Klebestreifen von den Schallschutzteilen. • Bringen Sie die vier Schallschutzteile auf der Geräteunterseite an.
DEUTSCH 45 • Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. Aus dem Ablaufschlauch könnte Wasser austreten. Dies ist auf den Test mit Wasser im Werk zurückzuführen. • Lösen Sie die drei Schrauben. • Verwenden Sie dazu den mitgelieferten Schraubenschlüssel. • Ziehen Sie die KunststoffAbstandshalter heraus. • Setzen Sie die Kunststoffkappen in die Öffnungen. • Diese Kappen finden Sie im Beutel mit der Gebrauchsanleitung.
www.aeg.com 17.3 Montage als Einbaugerät Das Gerät kann freistehend oder unter einer Küchenarbeitsplatte in einer Nische mit den entsprechenden Abmessungen montiert werden (siehe Abbildung). 600 mm ≥ 870 mm ACHTUNG! Um eine ungehinderte Luftzirkulation unter dem Gerät zu gewährleisten, bringen Sie keine Schallschutzteile an (falls verfügbar). 600 mm 17.4 Aufstellen und Ausrichten x4 • Stellen Sie das Gerät auf einen ebenen, festen Boden.
DEUTSCH 47 17.5 Wasserzulaufschlauch • Schließen Sie den Schlauch an der Rückseite des Geräts an. Drehen Sie den Wasserzulaufschlauch nur nach links oder rechts. • Lösen Sie die Ringmutter, um ihn in die gewünschte Position zu bewegen. 45 20 O O • Schließen Sie den Wasserzulaufschlauch an einen Kaltwasserhahn mit einem 3/4"Außengewinde an. ACHTUNG! Achten Sie darauf, dass die Anschlüsse dicht sind. Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist.
www.aeg.com • Den Ablaufschlauch U-förmig biegen. Über eine Waschbeckenkante • Stellen Sie sicher, dass die KunststoffFührung beim Abpumpen nicht herausrutschen kann. Befestigen Sie deswegen die Führung am Wasserhahn oder an der Wand. An ein Standrohr mit Entlüftungsöffnung • Direkte Einleitung in ein Abflussrohr bei einer Höhe von mindestens 60 cm (23,6") und höchstens 100 cm (39,3"). Orientieren Sie sich an der Abbildung. • Das Ende des Ablaufschlauchs muss stets belüftet sein, d. h.
DEUTSCH 49 An einen Siphon • Orientieren Sie sich an der Abbildung. Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. • Stellen Sie sicher, dass der Schlauch einen Bogen beschreibt, damit kein Schmutz aus dem Siphon in das Gerät gelangen kann. An ein Wandrohr • Direkte Einleitung in ein Abflussrohr in der Zimmerwand. Mit einer Schlauchschelle befestigen. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
www.aeg.com Max. Trockenladung Schleuderdrehzahl Baumwolle 6 Pflegeleicht 4 Wolle 1 Höchstens 1600 U/min 1) Schließen Sie den Zulaufschlauch an einen Wasserhahn mit einem 3/4"-Außengewinde an. 19. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte. Entsorgen Sie * Geräte mit diesem Symbol nicht mit dem Hausmüll.
DEUTSCH 51
132911712-A-472014 www.aeg.