DE Benutzerinformation Wasch-Trockner L 99699 HWD
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.................................................................................. 4 2. SICHERHEITSANWEISUNGEN...................................................................................... 7 3. GERÄTEBESCHREIBUNG...............................................................................................9 4. BEDIENFELD................................................................................................................. 10 5.
DEUTSCH Änderungen vorbehalten.
1. www.aeg.com SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Sicherheit von Kindern und schutzbedürftigen Personen WARNUNG! Erstickungs- und Verletzungsgefahr sowie Gefahr einer dauerhaften Behinderung.
DEUTSCH • • • • • • • • • • 5 Das Gerät kann freistehend oder unter einer Küchenarbeitsplatte in einer Nische mit den entsprechenden Abmessungen montiert werden. Das Gerät darf nicht hinter einer verschließbaren Tür, einer Schiebetür oder einer Tür mit einem Scharnier, das dem des Gerätes gegenüber liegt und eine vollständige Öffnung der Gerätetür verhindert, aufgestellt werden. Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose.
www.aeg.com • • • • • • • • • • • • Wischen Sie die um das Gerät ggf. angesammelten Flusen weg. Benutzen Sie das Gerät nie ohne Filter. Reinigen Sie den Flusenfilter vor oder nach jedem Gebrauch. Wäschestücke, die mit Speiseöl verschmutzt sind oder die mit Aceton, Alkohol, Kerosin, Fleckentfernern, Terpentin und Wachsentfernern behandelt worden sind, müssen vor dem Trocknen im Wasch-Trockner in heißem Wasser und zusätzlichem Waschmittel gewaschen werden.
DEUTSCH • 7 Reinigungsschwämmchen, Lösungsmittel oder Metallgegenstände. Schalten Sie das Gerät immer aus und ziehen Sie den Netzstecker aus der Steckdose, bevor Reinigungsarbeiten durchgeführt werden. 2. SICHERHEITSANWEISUNGEN 2.1 Montage • Halten Sie sich an die mitgelieferte Montageanleitung. • Das Gerät darf nicht an einem Ort aufgestellt oder verwendet werden, an dem die Temperatur unter 5 °C absinken oder auf über 35 °C steigen kann.
www.aeg.com 2.4 Gebrauch WARNUNG! Verletzungs-, Stromschlag-, Brand-, Verbrennungsgefahr sowie Risiko von Schäden am Gerät. • Das Gerät ist ausschließlich für die Verwendung im Haushalt vorgesehen. • Nehmen Sie keine technischen Änderungen am Gerät vor. • Platzieren Sie keine entflammbaren Produkte oder Gegenstände, die mit entflammbaren Produkten benetzt sind, im Gerät, auf dem Gerät oder in der Nähe des Geräts. • Berühren Sie während des Betriebs nicht das Türglas. Das Glas kann sehr heiß sein.
DEUTSCH 3. GERÄTEBESCHREIBUNG 3.1 Geräteübersicht 1 2 3 10 4 11 12 5 6 13 7 9 8 1 2 3 4 5 6 7 8 Arbeitsplatte Waschmittelschublade Luftfilter Bedienfeld Türgriff Typenschild Filter der Ablaufpumpe Schraubfüße zum Ausrichten des Geräts 14 9 10 11 12 13 14 Luftschlitze Wasserablaufschlauch Wassereinlassventil Netzkabel Transportschrauben Schraubfüße zum Ausrichten des Geräts 3.
www.aeg.com 3.3 Zubehör 1 2 5 4 1 Schraubenschlüssel Zum Lösen der Transportschrauben. 2 Kunststoffkappen Zum Verschließen der Öffnungen auf der Rückseite des Geräts nach dem Entfernen der Transportschrauben. 3 Schallschutzteile Zur Minderung der Geräuschbelastung während des Gerätebetriebs. 4 Kunststoff-Schlauchführung Zum Einhängen des Ablaufschlauchs an einer Waschbeckenkante. 5 Aqua-Safe-Zulaufschlauch Zur Verhinderung von eventuellen Wasserlecks. 3 4. BEDIENFELD 4.
DEUTSCH 12 Sensortaste Drehzahlreduzierung (U./ Min.) 11 13 Sensortaste Temperatur (Temp.) 4.2 Display A K J B I H G C F D E Im Display wird folgendes angezeigt: A Die Textzeile: • Hilft Ihnen bei der Benutzung des Geräts. • Informiert Sie über den Programmstatus und die Programmphase. • Zeigt Fehlermeldungen an. Siehe hierzu „Fehlersuche“. Die Symbole erscheinen im Display, wenn die zugehörige Programmphase oder Funktion eingestellt ist.
www.aeg.com Zahlenbereich Uhrzeit Wenn Sie das Gerät einschalten, zeigt das Display einige Sekunden lang die Uhrzeit an. Informationen zur Änderung der Uhrzeit finden Sie unter „Einstellen der Uhrzeit“. Programmdauer Wenn Sie das Programm einstellen, wird die Programmdauer einige Sekunden lang angezeigt, danach erscheint wieder die Endzeit des Programms. Anzeige Programmdauer Die Anzeige erscheint, sobald die Ziffern die Programmdauer anzeigen.
DEUTSCH 13 Zeit sparen Die Anzeige leuchtet auf, wenn Sie die Programmdauer einstellen. F Verkürzte Programmdauer Extra Kurz G Anzeige für Luftfilter Extra Spülen H Die Zahl steht für die Gesamtzahl der Spülgänge. Der Anzeigebalken füllt sich entsprechend der Anzahl der Spülgänge. Anzeige Flecken Anzeige Vorwäsche I Anzeige Einweichen Der Anzeigebalken füllt sich entsprechend der eingestellten Funktionen.
www.aeg.com 5. PROGRAMME 5.1 Programmübersicht Programm Temperaturbereich Maximale Bela- Programmbeschreibung dung (Beladung und Verschmutzungsgrad) Maximale Schleuderdrehzahl Wasch-/Trockenprogramme1) Koch/Bunt 95 °C - Kalt Baumwolle Eco2) 60 °C - 40 °C Pflegeleicht 60 °C - Kalt Wolle/Seide 40 °C - Kalt Anti-Allergie 60 °C 9 kg 1600 U/min Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. 9 kg 1600 U/min Weiße und farbechte Baumwollwäsche. Normal verschmutzt.
DEUTSCH Programm Temperaturbereich 15 Maximale Bela- Programmbeschreibung dung (Beladung und Verschmutzungsgrad) Maximale Schleuderdrehzahl 4 kg 800 U/min Pflegeleichte Textilien, die sanft gewaschen wer- Super Eco Kalt 3 kg 1200 U/min Mischgewebe (Baumwolle und Synthetik)5) 20 Min. - 3 kg 40 °C - 30 °C 3 kg 1200 U/min Teile aus Baumwolle oder Synthetik, die leicht verschmutzt sind oder nur einmal getragen wurden. 9 kg 1600 U/min Alle Gewebearten. Spülen und Schleudern der Wäsche.
www.aeg.com Programm Temperaturbereich Maximale Bela- Programmbeschreibung dung (Beladung und Verschmutzungsgrad) Maximale Schleuderdrehzahl bis zu 1.5 kg Auffrischen 40 °C Dampfprogramm für Baumwolle und pflegeleichte Wäsche. Dieses Programm beseitigt Gerüche aus der Wäsche.7) 1) Wenn Sie ein Wasch-/Trockenprogramm einstellen, zeigt das Display an, dass das Trockenprogramm nicht eingestellt ist. Wenn Sie Ihre Wäsche trocknen möchten, wählen Sie ein Automatikprogramm oder ein Zeitprogramm.
DEUTSCH 17 Zeitvorwahl Zeit Sparen2) Extra Spülen1) Flecken Anti-Allergie ■ ■ ■ ■ ■ Feinwäsche ■ ■ ■ ■ ■ ■ ■ Leichtbügeln ■ ■ ■ ■ ■ ■ ■ Super Eco ■ ■ 20 Min. - 3 kg ■ Spülen ■ Schleudern/Pumpen ■ U./Min. Vorwäsche Einweichen Programm ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) Ist die Funktion Extra Spülen eingeschaltet, führt das Gerät zusätzliche Spülgänge aus.
www.aeg.com 5.3 Programme für das zeitgesteuerte Trocknen Trockengrad Gewebetyp Beladung (kg) Extra Trocken Für Frotteewaren Baumwolle und Leinen (Bademäntel, Badetücher usw.) Schleu- Vorgeschladerdreh- gene Dauer zahl (U/ (Min.) min) 6 1600 240 - 250 3 1600 120 - 140 1 1600 50 - 60 6 1600 230 - 240 3 1600 110 - 130 1 1600 40 - 50 Schranktrocken Für Wäschestücke, die sofort in den Schrank kommen Baumwolle und Leinen (Bademäntel, Badetücher usw.
DEUTSCH 6. VERBRAUCHSWERTE Bei den in dieser Tabelle angegebenen Werten handelt es sich um Richtwerte. Folgende Faktoren können diese Werte verändern: Die Wäscheart und -menge, die Wasser- und Raumtemperatur. Am Programmstart zeigt das Display die Programmdauer für die maximale Beladung an. Während der Waschphase wird die Programmdauer automatisch berechnet und verringert sich möglicherweise beträchtlich, wenn die Wäsche weniger wiegt als die maximal zulässige Beladung.
www.aeg.com • Berühren Sie zum Ein-/Ausschalten dieser Funktion Temp. und U./Min. auch wenn Sie ein neues Programm einstellen. gleichzeitig, bis die Anzeige aufleuchtet/erlischt. Wenn Sie diese Funktion einschalten: • Berühren Sie zum Ein-/Ausschalten dieser Funktion Zeit Sparen und Zeitvorwahl gleichzeitig, bis die • Nachdem Sie Start/Pause berührt haben: sind alle Tasten und der Programmwahlschalter ausgeschaltet. • Bevor Sie Start/Pause berührt haben: kann das Gerät nicht starten.
DEUTSCH 21 • Berühren Sie diese Taste zur Einstellung der Dampfmenge. Diese Option ist nur bei Programmen mit vorhandener Dampffunktion möglich. Die Dauer der Dampfphase ändert sich entsprechend Ihrer Einstellung. Vorwäsche Verwenden Sie diese Funktion bei stark verschmutzter Wäsche. Das Gerät fügt vor dem Hauptwaschgang einen Vorwaschgang hinzu. Die Programmdauer verlängert sich entsprechend. • Einweichen Verwenden Sie diese Funktion bei stark verschmutzter Wäsche.
www.aeg.com 9. REINIGEN SIE VOR DEM ERSTEN GEBRAUCH 1. Geben Sie eine kleine Waschmittelmenge in das Waschmittelfach für die Hauptwäsche. 2. Stellen Sie ein Koch-/BuntwäscheProgramm mit der höchsten Temperatur ein und starten Sie das Programm mit leerer Trommel. So werden alle eventuellen Verunreinigungen aus Trommel und Bottich entfernt. 9.1 Einstellen der Uhrzeit Nach der Einstellung der Sprache werden Sie aufgefordert, die Uhrzeit einzustellen: Die Stundenziffern blinken. 1.
DEUTSCH Die Programmkontrolllampe leuchtet auf. Die Kontrolllampe der Taste Start/Pause blinkt rot. Das Display zeigt die StandardTemperatur und -Drehzahl und bei geöffneter Tür die für das Programm maximal erlaubte Füllmenge an (diese Informationen erlöschen, sobald Sie die Tür schließen). 3. Berühren Sie, falls notwendig, die Tasten Temp. und U./Min., um die Wassertemperatur und Schleuderdrehzahl zu ändern. 4.
www.aeg.com 2. A Stellung A: für Waschpulver (Werkseinstellung). 3. B Drehen Sie die Klappe nach unten. Stellung B: für Flüssigwaschmittel. 4. Bei Verwendung von Flüssigwaschmitteln: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. • Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Obergrenze. • Stellen Sie nicht den Vorwaschgang ein. • Stellen Sie nicht die Zeitvorwahl ein. 10.
DEUTSCH Das Gerät zählt die Zeit herunter. Nach Ablauf der Zeitvorwahl startet das Programm automatisch. Sie können die Zeitvorwahl vor dem Einschalten des Geräts mit der Taste Start/ Pause jederzeit abbrechen oder ändern. 10.9 Abbrechen der Zeitvorwahl 1. Berühren Sie die Taste Start/Pause. Die zugehörige Kontrolllampe blinkt. 2. Berühren Sie die Taste Zeitvorwahl mehrmals, bis das Display meldet, dass keine Zeitvorwahl eingestellt ist. 3. Berühren Sie die Taste Start/Pause. Das Programm wird gestartet.
www.aeg.com automatisch aus, um den Energieverbrauch zu verringern: Falls Signaltöne eingeschaltet sind, ertönt ein Signalton. • Wenn Sie nicht innerhalb von 5 Minuten die Taste Start/Pause drücken. Drücken Sie die Taste Ein/Aus, um das Gerät wieder einzuschalten. • 5 Minuten nach Ende eines Waschprogramms Drücken Sie die Taste Ein/Aus, um das Gerät wieder einzuschalten. Im Display wird das Ende des zuletzt eingestellten Programms angezeigt.
DEUTSCH Zu Beginn eines Trockengangs (in den ersten 3 - 5 Min.) ist der Geräuschpegel möglicherweise etwas höher. Dies ist auf den Kompressorstart zurückzuführen und ist normal bei Geräten, die mit einem Kompressor ausgestattet sind, wie Kühlschränke, Gefriergeräte usw. 11.2 Automatiktrocknen 1. Berühren Sie Automatik Trocknen wiederholt zur Einstellung des erforderlichen Trockengrads. Die Kontrolllampen auf dem Bedienfeld leuchten je nach eingestelltem Trockengrad. a.
www.aeg.com Einige Minuten nach Ende des Programms schaltet die Energiesparfunktion das Gerät automatisch aus. 1. Nehmen Sie die Wäsche aus dem Gerät. 2. Vergewissern Sie sich, dass die Trommel leer ist. 12. TÄGLICHER GEBRAUCH - WASCHEN UND TROCKNEN WARNUNG! Siehe Kapitel Sicherheitshinweise. 12.1 NON-STOP Programm Sie können ein „Non-StopProgramm“ einstellen, um die Wäsche zu waschen und zu trocknen. Gehen Sie hierzu folgendermaßen vor: 1.
DEUTSCH Durch jeden Tastendruck erhöht sich die Trockenzeit um 5 Minuten. Die eingestellte Trockenzeit erscheint auf dem Display. 2. Drücken Sie Start/Pause, um das Programm zu starten. Das Display zeigt das Türverriegelungssymbol und das Symbol für das laufende Programm an. Abwechselnd erscheinen die Programmdauer und die Endzeit. Die Textzeile zeigt an, dass das Gerät in Betrieb ist. 12.4 Am Programmende Das Gerät wird automatisch ausgeschaltet. Falls Signaltöne aktiviert sind, ertönt ein Signalton.
www.aeg.com • Wenden Sie mehrlagige Textilien, Wolle und bedruckte Wäschestücke vor dem Waschen. • Entfernen Sie hartnäckige Flecken. • Waschen Sie stark verschmutzte Bereiche mit einem speziellen Waschmittel. • Seien Sie vorsichtig mit Gardinen. Entfernen Sie die Haken, oder stecken Sie die Gardinen in einen Beutel oder Kopfkissenbezug. • Waschen Sie keine ungesäumten Wäschestücke und Wäschestücke mit Schnitten im Stoff in der Maschine.
DEUTSCH • Der Wasserablaufschlauch muss richtig angeschlossen sein. Näheres siehe „Montage“. • Informationen zur Höchstbeladung für die Trockenprogramme entnehmen Sie bitte der Tabelle „Trockenprogramme“. 13.7 Wäschestücke, die nicht getrocknet werden sollen Stellen Sie kein Trockenprogramm für folgende Wäschearten ein: • Besonders empfindliche Gewebe. • Synthetikvorhänge. • Kleidungsstücke mit Metalleinsätzen. • Nylonstrümpfe. • Steppdecken. • Bettdecken. • Daunen. • Anoraks. • Schlafsäcke.
www.aeg.com der Trommel zurückbleiben. Führen Sie regelmäßig einen Waschgang zur Pflege der Maschine durch: ACHTUNG! Verwenden Sie keinen Alkohol, keine Lösungsmittel und keine Chemikalien. • Nehmen Sie die Wäsche aus der Trommel. • Starten Sie ein Programm für Koch-/ Buntwäsche mit der maximalen Temperatur und einer kleinen Menge Waschmittel. 14.2 Entkalken Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Entkalkers für Waschmaschinen. 14.
DEUTSCH 3. 33 4. 14.6 Reinigen der Luftfilter Die Luftfilter halten Flusen zurück. Die Flusen entstehen, wenn die Wäsche in einem Wasch-Trockner getrocknet wird. • Am Ende eines jeden Trockenprogramms leuchtet im Display die Anzeige , um Sie darauf hinzuweisen, dass der Hauptluftfilter gereinigt werden muss. Die Textzeile empfiehlt Ihnen, den Hauptfilter zu reinigen (siehe Abbildungen 1 bis 5). , um Sie daran zu erinnern, dass beide Luftfilter • Gelegentlich blinkt die Anzeige gereinigt werden müssen.
www.aeg.com U P L L 5. 6. 7. 8. + 10. 9. Um beste Trockenergebnisse zu erzielen, reinigen Sie die Luftfilter regelmäßig mit warmen Wasser und trocknen Sie sie mit einem Handtuch. Durch verstopfte Filter verlängert sich die Trockenzeit und erhöht sich der Energieverbrauch. WARNUNG! Die Aussparung des Hauptfilters darf nicht durch Gegenstände blockiert werden. Wenn Sie in Ihrem Wasch-Trockner ausschließlich Wäsche waschen, kann sich im Hauptluftfilter Feuchtigkeit ansammeln. 14.
DEUTSCH 1. 2. 2 1 1 2 1 3. 4. 1 5. 6. 1 7. 2 2 8.
www.aeg.com 9. 2 1 14.8 Reinigen des Zulaufschlauchfilters und Ventilfilters Die Filter müssen in folgenden Fällen gereinigt werden: • Es läuft kein Wasser in das Gerät. • Das Wasser läuft sehr lange in das Gerät ein. • Die Kontrolllampe der Taste Start/Pause blinkt und im Display wird der entsprechende Alarm angezeigt. Siehe hierzu „Fehlersuche“. So reinigen Sie die Wasserzulauffilter: • Schließen Sie den Wasserhahn. • Entfernen Sie den Wasserzulaufschlauch vom Wasserhahn.
DEUTSCH 37 • Reinigen Sie den Filter im Ventil mit einer harten Bürste oder einem Handtuch. • Bringen Sie den Zulaufschlauch wieder an. Vergewissern Sie sich, dass alle Anschlüsse vollkommen dicht sind, damit kein Wasser austreten kann. • Öffnen Sie den Wasserhahn. 45° 20° 14.9 Notentleerung 14.10 Frostschutzmaßnahmen Das Gerät kann aufgrund einer Funktionsstörung das Wasser nicht abpumpen.
www.aeg.com 15. FEHLERSUCHE WARNUNG! Siehe Kapitel Sicherheitshinweise. 15.1 Einleitung Das Gerät startet nicht oder stoppt während des Betriebs. Versuchen Sie zunächst selbst eine Lösung für das Problem zu finden (siehe Tabelle). Wenn Sie keine Lösung finden, wenden Sie sich an den autorisierten Kundendienst. Bei einigen Problemen ertönt ein Signalton und das Display zeigt eine Fehlermeldung an: ACHTUNG! Schalten Sie das Gerät aus, bevor Sie die Überprüfungen vornehmen. 15.
DEUTSCH Meldung 39 Mögliche Abhilfe Vergewissern Sie sich, dass der Wasserablaufschlauch ordnungsgemäß angebracht ist. Im Display erscheint die Auf- Vergewissern Sie sich, dass die Gerätetür nicht offen steht forderung, die Tür zu überund ordnungsgemäß geschlossen ist. prüfen. Das Display meldet einen Wasseralarm. Das Wasserauslauf-Schutzsystem wurde ausgelöst: • Schalten Sie das Gerät aus. • Schließen Sie den Wasserhahn. • Wenden Sie sich an den Kundendienst.
www.aeg.com Problem Mögliche Abhilfe Das Wasser, das in das Gerät Vergewissern Sie sich, dass sich der Ablaufschlauch in der einläuft, wird sofort abgerichtigen Höhe befindet. Der Schlauch ist möglicherweise pumpt. zu niedrig positioniert. Das Gerät schleudert nicht oder das Waschprogramm dauert länger als gewöhnlich. Vergewissern Sie sich, dass die Schleuderphase nicht ausgeschaltet ist. Vergewissern Sie sich, dass der Ablauffilter nicht verstopft ist. Reinigen Sie ggf. den Filter.
DEUTSCH Problem Mögliche Abhilfe Die Waschergebnisse sind nicht zufriedenstellend. Erhöhen Sie die Waschmittelmenge oder benutzen Sie ein anderes Waschmittel. 41 Entfernen Sie vor dem Waschgang hartnäckige Flecken mit einem Spezialprodukt. Achten Sie darauf, die richtige Temperatur einzustellen. Verringern Sie die Beladung. Das Waschprogramm ist kürzer als die angezeigte Zeit. Das Gerät berechnet eine neue Programmdauer entsprechend der Beladung. Das Waschprogramm ist länger als die angezeigte Zeit.
www.aeg.com Schalten Sie das Gerät nach der Überprüfung wieder ein. Das Programm wird an der Stelle fortgesetzt, an der es unterbrochen wurde. Tritt das Problem erneut auf, wenden Sie sich an den autorisierten Kundendienst. Wenn im Display andere Alarmcodes angezeigt werden. Schalten Sie das Gerät aus und wieder ein. Tritt das Problem weiterhin auf, wenden Sie sich an den autorisierten Kundendienst. 15.
DEUTSCH 43 16.1 Auspacken WARNUNG! Da Sie das Gerät auf seiner Rückseite ablegen werden, müssen Sie anschließend etwa 6 Stunden warten, bevor Sie es benutzen. Diese Zeit ist notwendig, damit der Kompressor richtig arbeiten kann. WARNUNG! Entfernen Sie vor der Montage des Geräts alle Verpackungsmaterialien und Transportschrauben. Tragen Sie Handschuhe. • Entfernen Sie die äußere Folie. Benutzen Sie, falls erforderlich, einen Cutter. • Nehmen Sie die Karton-Abdeckung ab.
www.aeg.com • Öffnen Sie die Tür. • Entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel. • Legen Sie eines der Styroporverpackungsteile hinter dem Gerät auf den Boden. • Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. • Achten Sie darauf, die Schläuche nicht zu beschädigen. • Entfernen Sie den Styroporschutz von der Geräteunterseite. 1 2 • Reinigen Sie die Unterseite des Geräts und trocknen Sie sie ab.
DEUTSCH 45 Sortieren Sie die verschiedenen Teile des Schallschutzes nach Größe und Position. Orientieren Sie sich an der Abbildung: • A (VORDERSEITE) = Vorderseite des Geräts • B (RÜCKSEITE) = Rückseite des Geräts A B x4 • Entfernen Sie den Klebestreifen von den Schallschutzteilen. • Bringen Sie die vier Schallschutzteile auf der Geräteunterseite an. • Orientieren Sie sich an der Abbildung. Vergewissern Sie sich, dass die Schallschutzteile fest angebracht sind.
www.aeg.com • Lösen Sie die drei Schrauben. • Verwenden Sie dazu den mitgelieferten Schraubenschlüssel. • Ziehen Sie die KunststoffAbstandshalter heraus. • Setzen Sie die Kunststoffkappen in die Öffnungen. • Diese Kappen finden Sie im Beutel mit der Gebrauchsanleitung. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren. 16.2 Satz Fixierplatten (4055171146) Sie erhalten den Bausatz bei Ihrem autorisierten Händler.
DEUTSCH 47 16.3 Montage unter einer Arbeitsplatte Das Gerät kann freistehend oder unter einer Küchenarbeitsplatte in einer Nische mit den entsprechenden Abmessungen montiert werden (siehe Abbildung). 600 mm ≥ 870 mm ACHTUNG! Montieren Sie das Gerät nicht in einer abgedichteten Hohlkonstruktion. Stellen Sie sicher, dass die Luft unter dem Boden des Möbels zirkulieren kann.
www.aeg.com 16.5 Wasserzulaufschlauch • Schließen Sie den Schlauch an der Rückseite des Geräts an. Drehen Sie den Wasserzulaufschlauch nur nach links oder rechts. • Lösen Sie die Ringmutter, um ihn in die gewünschte Position zu bewegen. 45 20 O O • Schließen Sie den Wasserzulaufschlauch an einen Kaltwasserhahn mit einem 3/4"Außengewinde an. ACHTUNG! Achten Sie darauf, dass die Anschlüsse dicht sind. Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist.
DEUTSCH 49 • Den Ablaufschlauch U-förmig biegen. Über eine Waschbeckenkante • Stellen Sie sicher, dass die KunststoffFührung beim Abpumpen nicht herausrutschen kann. Befestigen Sie deswegen die Führung am Wasserhahn oder an der Wand. An ein Standrohr mit Entlüftungsöffnung • Direkte Einleitung in ein Abflussrohr bei einer Höhe von mindestens 60 cm (23,6") und höchstens 100 cm (39,3"). Orientieren Sie sich an der Abbildung. • Das Ende des Ablaufschlauchs muss stets belüftet sein, d. h.
www.aeg.com An einen Siphon • Orientieren Sie sich an der Abbildung. Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. • Stellen Sie sicher, dass der Schlauch einen Bogen beschreibt, damit kein Schmutz aus dem Siphon in das Gerät gelangen kann. An ein Wandrohr • Direkte Einleitung in ein Abflussrohr in der Zimmerwand. Mit einer Schlauchschelle befestigen. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
DEUTSCH Max. Trockenladung Schleuderdrehzahl Baumwolle 6 Pflegeleicht 4 Wolle 1 Höchstwert 1600 U/min 51 Das Gerät enthält 120 g fluoriertes HFC - R134a/GWP1430 Gas, das hermetisch verschlossen ist. 1) Schließen Sie den Zulaufschlauch an einen Wasserhahn mit einem 3/4"-Außengewinde an. 18. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern.
132911713-A-092015 www.aeg.