L9FEA9612N USER MANUAL EN User Manual Washing Machine
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................4 3. INSTALLATION............................................................................................................6 4. PRODUCT DESCRIPTION.........................................................................................10 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com areas for communal use in blocks of flats or in launderettes. Do not exceed the maximum load of 9 kg (refer to the "Programme chart" chapter). The operating water pressure at the water entry point from the outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar (0.8 MPa). The ventilation opening in the base must not be covered by a carpet, mat, or any floor covering.
ENGLISH • When the appliance is in its permanent position, check if it is levelled correctly with the aid of a spirit level. If it is not, adjust the feet accordingly. • Do not install the appliance directly above a floor drain. • Do not spray water on the appliance and do not expose it to excessive humidity. • Do not install the appliance where the appliance door cannot be fully opened. • Do not put a closed container to collect possible water leakage under the appliance.
www.aeg.com 2.6 Disposal WARNING! Risk of injury or suffocation. • Disconnect the appliance from the mains electrical and water supplies. • Cut off the mains electrical cable close to the appliance and dispose of it. • Remove the door catch to prevent children or pets from becoming trapped in the drum. • Dispose of the appliance in accordance with local requirements for the disposal of Waste Electrical and Electronic Equipment (WEEE). 3. INSTALLATION WARNING! Refer to Safety chapters. 3.
ENGLISH Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. 12. Refer to the illustration. Make sure that the barriers are securely attached. x4 1 2 8. Fully clean and dry the bottom of the appliance. CAUTION! Do not use alcohol, solvents or chemical products. 9. Make sure to identify the different sizes and the positions of the sound barriers. Refer to the illustration: 7 A B Attach the sound barriers at a room temperature. 13.
www.aeg.com 16. Pull out the plastic spacers. 17. Put the plastic caps, that you find in the user manual bag, in the holes. x4 The appliance must be level and stable. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.2 Positioning and levelling 1. Install the appliance on a flat hard floor.
ENGLISH 9 A 45 20 O O If this occurs, close the water tap and contact the authorized service centre to replace the hose. 3.5 Water drainage Make sure that the inlet hose is not in vertical position. 3. If necessary, loose the ring nut to set it in the correct position. 4. Connect the water inlet hose to the cold water tap with 3/4" thread. The drain hose should be positioned at a height of not less than 60 cm and not more than 100 cm from the floor. You can extend the drain hose to maximum 400 cm.
www.aeg.com Make sure that the drain hose end is not immersed in the water. There may be a return of dirty water into the appliance. 3. To a stand pipe with vent-hole Insert the drain hose directly into a drain pipe. Refer to the illustration. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm min. 1.5") must be larger than the external diameter of the drain hose. 4.
ENGLISH • The Oko-Mix technology has been designed to protect the fabric fibres thanks to different pre-mixing phases that dissolves first the detergent and then fabric softener in the water before they are distributed in the laundry. So every fibre is reached and cared for. • Thanks to the Weight Sensors the appliance can detect the weight of your load and advise on how much detergent you need to achieve the best results without waste.
www.aeg.com 4.3 Detergent dispenser and salt compartment Always follow the instructions that you find on the packaging of the detergent products. Anyway, we recommend not to exceed the maximum indicated level in each compartment ( ). Salt Compartment for liquid additives (fabric conditioner, starch). Compartment for salt. Read carefully 'The Water Softener technology ( Soft Water)'. Maximum level for detergent/ additives quantity.
ENGLISH The first time you turn the appliance on, the touch screen proposes different settings: one on this is water hardness level. 13 4. Scroll the list up and down to find Water Hardness. 5. Tap on the Water Hardness bar. 6. Scroll the level list right and left to chose the proper level. 5.2 How to set the water hardness level The appliance allows you to chose between 7 levels corresponding to 7 different ranges of water hardness.
www.aeg.com Water hardness levels Levels as indicated on the Levels Water hardness range tester1) °f (French degrees) °d (German degrees) °e (English degrees) mmol/l ppm 1 C01 ≤5 ≤3 ≤4 ≤0.5 ≤ 50 2 C02 6 - 13 4-7 5-9 0.6 - 1.3 60 - 130 3 C03 14 - 21 8 - 11 10 -15 1.4 - 2.1 140 - 210 42) C04 22 - 29 12 - 16 16 - 20 2.2 - 2.9 220 - 290 5 C05 30 - 37 17 - 20 21 - 26 3.0 - 3.7 300 - 370 6 C06 38 - 45 21 -25 27 - 32 3.8 - 4.5 380 - 450 7 C07 ≥46 ≥26 ≥33 ≥4.
ENGLISH Regularly check if there is enough salt. Salt The compartment can contain about 600 gr of salt that are sufficient for about 20 - 300 washing cycles (or 4 - 70 weeks) depending on the set water hardness level and whether the water softener is activated during wash phase only. If the water softener is activated also during rinse phase, the salt refilling lasts 5 - 80 washing cycles (or 1 - 18 weeks) depending on the set water hardness level. Refer to 'How to set the water hardness level'.
www.aeg.com 6. CONTROL PANEL 6.1 Control panel description 2 3 4 1 1 On/Off button 2 Programme dial 3 Touch screen 4 Start/Pause button 7. FIRST TIME START-UP Each time you turn the appliance on, the Start-up Screen appears on the touch screen. AEG 13.45 The first time you turn the appliance on, after the Start-up Screen you are guided through the initial setup procedure. 7.1 Language setup 1. Scroll the language list to find the desired language and hold the desired language pressed to set it.
ENGLISH 7.2 Time setup 17 desired programme. 1. Scroll the hour and minute bars to the right or to the left to set the current time. Info 3/4 13:45 Set Clock <12 13h 14> <44 45min 46> 2. Tap on the Set Clock bar to set the time. Info 3/4 13:45 Set Clock <12 13 h 14> <44 45min 46> 3. The following screen pops up: • tap on OK to confirm the set time. • tap on Change to change it.
www.aeg.com 4. Tap on OK to confirm or on Change to change the level. 7.5 Detergent Dosing You can set the average quantity of detergent suggested on the detergent packaging. 4. Scroll the submenu bar right or left to set the detergent dosage in ml that matches with the average dosage suggested on the detergent packaging. Info OFF Detergent Type 1 Detergent advice Advise on detergent level for best results. Set now or later? Later 50 ml <40 60> 5. Tap on the Detergent Type 1 bar.
ENGLISH After a few seconds, the programme list screen appears proposing Cottons as default programme. • The currently selected options. The shortcut allows to enter the additional option menu. 3h01min OKOPower ColourPro 40 Cottons 1200 Cottons Eco Synthetics 1h07min Max 9.0 Kg Cottons More If you don't scroll the programme list up and down, in a few seconds the programme summary screen appears. To return to the programme list screen just tap on the programme name (e.g. Cottons). 1h07min Max 9.
www.aeg.com 9. BEFORE FIRST USE During installation or before first use you may observe some water in the appliance. This is a residual water left in the appliance after a full functional test in the factory to ensure the appliance is delivered to customers in perfect working order and is no cause for concern. 1. Make sure that all transit bolts have been removed from the appliance. 2. Make sure that the electrical power is available and the water tap is open. 3.
ENGLISH Programme Programme description Delicates Delicate fabrics such as acrylics, viscose and mixed fabrics requiring gentler washing. Normal soil. Wool/Silk Machine washable wool, hand washable wool and other 21 fabrics with «hand washing» care symbol1).
www.aeg.com Programme Outdoor Programme description Do not use fabric softener and make sure that there is no softener residue in the detergent dispenser. Outdoor clothing, technical, sport fabrics, waterproof and breathable jackets, shell jackets with a removable fleece or inner insulation. The recommended laundry load is 2.5 kg. This programme can also be used as water-repellent restoring cycle, specifically tailored for treating clothes with a hydrophobic coating.
ENGLISH 23 Programme Programme description Machine Clean Maintenance cycle with hot water to clean and freshen the drum and to remove residue that may cause odour. For the best result use this cycle once a month. Before running this cycle, remove all items from the drum. Pour a cup of chlorine bleach or a washing machine cleaner in the washing phase compartment. DO NOT use both together.
www.aeg.com Programme Default temperature Maximum spin speed Maximum load Temperature range Spin speed range Outdoor 30 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 40 °C 60 °C - Cold 1200 rpm 1200 rpm - 400 rpm 9 kg 60 °C 1600 rpm 1600 rpm - 400 rpm 9 kg - 1600 rpm 1600 rpm - 400 rpm 9 kg - - 9 kg - 1600 rpm 1600 rpm - 400 rpm 9 kg 60 °C 1200 rpm 1200 rpm - 400 rpm - Jeans Anti-Allergy Rinse Drain Spin Machine Clean 2.5 kg2) 1 kg3) 1) Cotton Energy Saving Programme.
■ ■ ■ ■ Wool/Silk ■ ■ ■ 25 Steam Level Prewash ■ Anti-crease Stains3) ■ Soft Plus Eco2) ■ Plus Steam3) Extra Silent ■ Extra Rinse Rinse & Hold ■ Soak Spin Speed Delicates Time Save 1) ENGLISH ■ Steam 20min 3kg ■ Outdoor ■ ■ ■ ■ Anti-Allergy ■ ■ Rinse ■ ■ ■ Jeans ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Drain Spin ■ Machine Clean ■ 1) If you set the shortest duration, we recommend that you decrease the load size.
www.aeg.com +1 11.3 To return to the programme summary screen, tap on the programme bar.
ENGLISH 1. Tap on the Temperature bar to enter the submenu. 2. Scroll the submenu bar to set the desired temperature. Cold= Cold wash. When you return to programme summary screen, the set temperature will be shown. 11.6 The drum turns regularly to reduce creasing. You must drain the water to unlock the door. Touch the 启动/暂停 button: the appliance performs the draining phase only. The appliance empties the water out automatically after approximately 18 hours.
www.aeg.com containing sand, dust , mud and other solid particles. Tap on the Plus Steam bar to activate the option (ON status). Put the detergent for prewash in a dosing ball inside the drum. This option can increase the programme duration. This option can increase the programme duration. • Soak Use this function for heavy soiled garments. The appliance soaks the laundry at 30°C for about half an hour before washing. When you return to programme summary screen, the shortcut on. 11.
ENGLISH • Maximum This is available with the Steam programme only. 11.14 Memory With this option it is possible to save the two most used washing programmes. 29 1h07min Settings Cottons Cottons 40 M1 Cottons Eco Synthetics 1200 More To save your favourite programmes: To change a saved programme: 1. First set the washing programme and the desired options. 2. Tap on the Memory bar to enter the submenu. 3. Tap on the Memory 1 or Memory 2 to save the set programme.
www.aeg.com 12.4 Stand-by function The Stand-by function automatically deactivates the appliance to decrease the energy consumption when: • You do not use the appliance for 5 minutes before pressing the 启动/暂 停 button and turning the appliance on. Press the 开/关 button to activate the appliance again. • After 5 minutes from the end of the washing programme. Press the 开/关 button to activate the appliance again. The display shows the end of the last set programme.
ENGLISH If you put in the drum more laundry than the maximum load, the display tells that the suggested load has been exceeded. You can wash your laundry anyway, but the water and energy consumption increase. To have the best consumption and washing performance remove the excess items. The overload indication is shown only in programmes with a maximum load lower than the appliance maximum load. 4. Close the door. Make sure that no laundry stays between the seal and the door.
www.aeg.com Max ▼ Li qu id M ax ▼ Max ▼ ax ▼ M ▼ ax Sa lt Sa lt M ax ▼ M ax ▼ M 4. Close the detergent dispenser. 3. Close the detergent dispenser. 12.8 Starting a programme Max ▼ ax ▼ Sa lt M ax ▼ M Filling the liquid detergent 1. Insert the proper container for liquid detergent. Max ▼ ax ▼ M 1. Touch the 启动/暂停 button to start the programme. The related led stops flashing and stays on. The door is locked.
ENGLISH The shortcut shows up. Keep pressed for about three seconds to deactivate the Child Lock. Starting a programme with delay start 1. Touch the 启动/暂停 button to start the programme. The related led stops flashing and stays on. The door is locked. The appliance starts the countdown and the door is locked. Cottons 40 Starts in 1h29min Reset Finished at 15:36 2. Tap on Reset to cancel the delay start and then touch the 启动/暂停 button or wait until the countdown is completed.
www.aeg.com If is on: the water temperature and level are not high and it is still possible to open the door and add clothes. While a programme or the delay start operates, the appliance door is locked. 1. Touch the 启动/暂停 button . In the display the related door lock indicator goes off. 2. Open the appliance door. If necessary, add or remove the items. 3. Close the door and touch the 启动/ 暂停 button. The programme or the delay start continues. 12.
ENGLISH 13.4 35 Display Brightness Spin Machine Clean You can regulate the display brightness through 5 brightness levels. Settings To change the display brightness: OKOPower ColourPro 1. Tap on the Display Brightness bar. 2. Scroll the brightness level bar right or left to find the desired level. 3. Tap on the shortcut to enter the setting menu. 4. Scroll the setting list up or down to find the setting you want to change.
www.aeg.com 2. Scroll right or left to set the proper water level. Info 3. Tap on the Water Hardness bar to return to the machine setting list or tap on the Programmes bar to return to the programme summary screen. 13.
ENGLISH 13.10 13.12 Water Softener 37 Shortcuts This setting allows to bring the shortcuts shown in the next drawing visible on the summary screen. Read the "The Water Softener (SoftWater Technology)" chapter carefully. To activate the shortcuts: With this setting you can decide when the water softener function should operate: 1. Tap on the Shortcuts bar to open the list of the available shortcuts. Shortcuts
www.aeg.com To return to the factory settings: 1. Tap on the Factory Reset bar. The following window pops up. 2. Tap on OK to return to factory settings or on Cancel to keep the current settings. Do you want to clear all your programmed settings? Cancel OK 14. HINTS AND TIPS WARNING! Refer to Safety chapters. 14.1 The laundry load • Divide the laundry into: white, coloured, synthetics, delicates and wool. • Follow the washing instructions on the laundry care labels.
ENGLISH other treatments without exceeding the indicated maximum level ( ). • Use the recommended detergents for the type and colour of the fabric, the programme temperature and the level of soil. 14.4 Ecological hints • Set a programme without the prewash phase to wash laundry with normal soil. 39 • Always start a washing programme with the maximum load of laundry allowed. • If you pre-treat the stains, you can use a stain remover when you set a programme with a low temperature.
www.aeg.com M ax 15.4 Door seal Max ▼ ax ▼ Sa lt M ax ▼ M Regularly examine the seal and remove all objects from the inner part. 2. Remove the insert for the softener and, if inserted, the container for liquid detergent. 15.5 Cleaning the drum Regularly examine the drum to prevent rust forming. ▼ ax Max M ▼ Sa lt M ax ▼ For a complete cleaning: 1. Clean the drum with special products for stainless steel. Max ▼ M 1. Open the drawer.
ENGLISH 4. Make sure that all detergent residue is removed from the detergent conveyor. Use a cloth. 41 Regularly check the drain pump filter and make sure that it is clean. Clean the drain pump if: • The appliance does not drain the water. • The drum does not turn. • The appliance makes an unusual noise because of the blockage of the drain pump. • The message Check that the drain filter is not clogged pops up. 5.
www.aeg.com rotate, contact the Authorised Service Centre. 4. Turn the filter 180 degrees in anticlockwise direction to open it, without removing. Let the water flow out. 10. Clean the filter under the water tap. 11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 5. When the bowl is full of water, turn the filter back and empty the container. 6. Repeat the steps 4 and 5 until the water stops to flow out. 7.
ENGLISH 43 2 1 When you drain the water with the emergency drain procedure, you must activate the drain system again: a. Put 2 litres of water in the main wash compartment of the detergent dispenser. b. Start the programme to drain the water. 3. Clean the valve filter on the back of the appliance with a toothbrush. 15.8 Cleaning the inlet hose and the valve filter It is recommended to clean both the filters of the inlet hose and valve occasionally to remove any deposit, collected over the time: 1.
www.aeg.com 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. 15.10 Frost precautions If the appliance is installed in an area where the temperature can reach the values around 0° C or drop below, remove the remaining water from the inlet hose and the drain pump. 1. Disconnect the mains plug from the mains socket. 2. Close the water tap. 3.
ENGLISH popping up during next uses until it is run. 45 If the cleaning programme is postponed, the message keeps on popping up during next uses until it is run. 16.2 Possible failures Problem Possible solution The programme does not start. • Make sure that the mains plug is connected to the mains socket. • Make sure that the appliance door is closed. • Make sure that there is no damaged fuse in the fuse box. • Make sure that the 启动/暂停 has been touched.
www.aeg.com Problem Possible solution There is water on the floor. • Make sure that the couplings of the water hoses are tight and there is not water leakages. • Make sure that the water inlet hose and the drain hose have no damages. • Make sure you use the correct detergent and the correct quantity of it. You cannot open the appliance door. • Make sure that a washing programme that ends with water in tub, has been selected. • Make sure that the washing programme is finished.
ENGLISH Problem 47 Possible solution The drum is empty and • Press the 开/关 button to deactivate the appliance and actithe display shows there is vate it again to set a tare. some weight in. The drum is full but the display shows 0.0 kg. • You loaded the laundry before activating the appliance. Press the 开/关 button to deactivate the appliance. • Empty the drum and follow the necessary steps. (Refer to "Loading the laundry") After the check, activate the appliance.
www.aeg.com 2. Eliminate any trace of detergent or additive and clean the compartment thoroughly. 3. Insert the drawer back and pour salt M ax 48 Salt Max ▼ ax ▼ Sa lt M ax ▼ M in the compartment . 4. Close the drawer. 5. Run a cotton or synthetic cycle, without reducing time, to restore the water softener function. 17.
ENGLISH 18.3 Stacking kit 49 WARNING! Do not put the tumble dryer under the washing machine. 18.4 Pedestal with the drawer The tumble dryer can be stacked on the top of the washing machine only by using the correct stacking kit manufactured and approved by AEG. Verify the compatible stacking kit by checking the depth of your appliances. The stacking kit can be used only with the appliances specified in the leaflet provided with the accessory.
* X X X X X Motor (including belt) Hydraulics (inlet and drain hoses, pressure switch, pumps, including electrovalves) Control panel (including sensors, electronic boards - user interface, main board, motor control bard) Door (including hinge) Wirings and power cord Hg Cd Cr6+ Hazardous substances PBBs PBDEs 1. This table is compiled according to SJ/T11364-2014. means this kind of hazard substance content in all the homogenous material of this part is under the limitation regulated 2.
ENGLISH 51
157017771-A-172018 www.aeg.
