L9FEC96S USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................4 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 11 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com 1.2 Allgemeine Sicherheit • • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Überschreiten Sie nicht die maximale Beladungsmenge von 9 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • • • • • • • • • verriegeln und dadurch interne Schäden zu vermeiden. Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk. Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. Halten Sie sich an die mitgelieferte Montageanleitung. Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist.
www.aeg.com Substanzen verschmutzt sind. Die Gummiteile der Waschmaschine könnten beschädigt werden. Waschen Sie solche Textilien mit der Hand vor, bevor Sie sie in die Waschmaschine geben. • Berühren Sie während des Ablaufs eines Programms nicht die Glastür. Das Glas kann sehr heiß werden. 2.5 Service • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung.
DEUTSCH 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 1 2 8. Reinigen Sie die Unterseite des Geräts und trocknen Sie sie ab. 7 VORSICHT! Verwenden Sie keinen Alkohol, keine Lösungsmittel und keine Chemikalien. 9. Sortieren Sie die verschiedenen Teile des Schallschutzes nach Größe und Position.
www.aeg.com x4 A B Bringen Sie die Schallschutzteile bei Raumtemperatur an. 13. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 14. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. 16. Ziehen Sie die KunststoffAbstandshalter heraus. 17. Setzen Sie die Kunststoffkappen, die sich im Beutel mit der Bedienungsanleitung befinden, in die Löcher ein. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren. 3.
DEUTSCH 9 WARNUNG! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 45 20 x4 Das Gerät muss einen waagerechten und festen Stand haben. Durch eine korrekte waagrechte Ausrichtung des Geräts werden Vibrationen, Geräusche und ein Wandern des Geräts während des Betriebs vermieden. 3.3 Wasserzulaufschlauch 1. Schließen Sie den Wasserzulaufschlauch an der Rückseite der Maschine an. 2.
www.aeg.com verhindert Wasserlecks am Schlauch, die durch natürliche Alterung auftreten können. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an. Stellen Sie sicher, dass die Kunststoffführung beim Abpumpen nicht herausrutschen kann. A Tritt dieser Fall ein, drehen Sie den Wasserhahn zu und wenden Sie sich an den autorisierten Kundendienst, um den Schlauch zu erneuern. 3.5 Ablassen des Wassers Der Ablaufschlauch muss in einer Höhe nicht unter 60 cm und nicht über 100 cm angebracht werden.
DEUTSCH 11 Stellen Sie sicher, dass der Ablaufschlauch einen Bogen beschreibt, damit keine Partikel aus dem Becken in das Gerät gelangen können. 6. Stecken Sie den Schlauch direkt in ein Abflussrohr in der Zimmerwand und befestigen Sie ihn mit einer Schlauchschelle. 5. Ohne Kunststoffführung in einen Siphon - Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Orientieren Sie sich an der Abbildung. 4. GERÄTEBESCHREIBUNG 4.
www.aeg.com Wäsche verteilt, sodass er die Fasern durchdringt und für perfekte Weichheit sorgt. 4.2 Geräteübersicht 1 2 9 8 3 10 4 5 11 12 6 7 4.3 Waschmittelschublade und Salzfach Halten Sie sich immer an die Anweisungen auf der Waschmittelverpackung. Wir empfehlen Ihnen die Höchstmarke ( ) der einzelnen Fächer nicht zu überschreiten.
DEUTSCH Fach für die Hauptwäsche: Waschpulver, Fleckentferner. Maximaler Füllstand für Waschmittel/Pflegemittel Falls Sie Flüssigwaschmittel verwenden, achten Sie darauf, dass der Behälter für Flüssigwaschmittel eingesetzt ist. Siehe „Einfüllen von Wasch- und Pflegemitteln“ im Kapitel „Täglicher Gebrauch“. Salt 13 Falls Sie einen Vorwaschgang gewählt haben, geben Sie das Wasch-/Pflegemittel in eine Dosierkugel und legen Sie diese in die Trommel.
www.aeg.com 2. Warten Sie etwa 10 Sekunden, bis das Gerät die interne Kontrolle abgeschlossen hat. 3. Berühren Sie die Tasten Vlekken/ Voorwas - Taches/Prélavage (Flecken/Vorwäsche) und Plus Dampf einige Sekunden lang gleichzeitig (gleichzeitiges Berühren der Tasten wie in der folgenden Abbildung), bis das Display die voreingestellte Stufe C04 anzeigt und die Anzeige aufleuchtet. Dies bedeutet, dass der Wasserenthärter nur während des Waschgangs eingeschaltet ist.
DEUTSCH Grad 15 Wasserhärtebereich C01 ≤5 ≤3 ≤4 ≤0.5 C02 6 - 13 4-7 5-9 0.6 - 1.3 C03 14 - 21 8 - 11 10 -15 1.4 - 2.1 C041) 22 - 29 12 - 16 16 - 20 2.2 - 2.9 C05 30 - 37 17 - 20 21 - 26 3.0 - 3.7 C06 38 - 45 21 -25 27 - 32 3.8 - 4.5 C07 ≥46 ≥26 ≥33 ≥4.6 1) Werkseinstellung. Diese Einstellung ist für die meisten Anwendungen ausreichend. 5.3 Einfüllen von Salz 3. Füllen Sie das Spezialsalz ein.
www.aeg.com WARNUNG! Füllen Sie das Salz nur in das Salt Fach . WARNUNG! Salt Befüllen Sie das Fach ausschließlich mit Salz. Werden versehentlich Waschmittel oder Zusatzstoffe in dieses Fach gefüllt, siehe „Entfernen von Waschmittel oder anderen Zusätzen aus dem Salzfach“ im Kapitel „Fehlersuche“. Das Gerät arbeitet auch ohne Salz normal, jedoch ohne sein Potenzial voll auszuschöpfen.
DEUTSCH 17 7. BEDIENFELD 7.1 Bedienfeldbeschreibung 3 2 1 P r o g ra m m a / P r o g ra m m e Katoen Blanc/Couleurs Sy nth etic a Syn thétiq u es Eco C o l o u r P ro 4 Tijd Besparen Gain de temps Fijne Was Délicats Wol/Zijde Laine/Soie Stoom Vapeur 5 ÖKOPower Anti-Allergie Anti-Allergies 2 0 m i n . - 3 kg O u td o o r Temp. °C Vlek./Voorw. Taches/Prélav.
www.aeg.com 7.2 Display MIX Anzeige der max. Beladung. Das Symbol blinkt während der Messung der Wäschemenge (siehe Abschnitt „PROSENSE Beladungserkennung“). Anzeige des max. zulässigen Wäschegewichts. Blinkt, wenn das Wäschegewicht die maximal zulässige Füllmenge für das ausgewählte Programm überschreitet. Salt Salznachfüllanzeige. Es muss Salz in das Fach Fach ist leer oder enthält nicht genügend Salz. gefüllt werden. Das Zeitvorwahlanzeige. Türverriegelungsanzeige.
DEUTSCH 19 Dampfphasenanzeige. Knitterschutzphasenanzeige. Kindersicherungsanzeige. Zeitsparanzeige. Temperaturanzeige. Die Anzeige kaltem Wasser gewählt wurde. erscheint, wenn ein Waschgang mit Schleuderdrehzahlanzeige. Spülstoppanzeige. Anzeige Extra Leise. Vorwäscheanzeige. Fleckenanzeige. Anzeige Extra Spülen 8. PROGRAMMWAHLSCHALTER UND TASTEN 8.1 Aan /Uit - Marche/Arrêt Halten Sie diese Taste einige Sekunden lang gedrückt, um das Gerät ein- oder auszuschalten.
www.aeg.com Wenn das Display die Symbole und anzeigt, heizt das Gerät das Wasser nicht auf. 8.4 TPM Wenn Sie ein Programm auswählen, stellt das Gerät automatisch die höchste Schleuderdrehzahl ein. Drücken Sie diese Taste wiederholt, um • die Schleuderdrehzahl zu reduzieren. Das Display zeigt nur die Schleuderdrehzahlen an, die für das eingestellte Programm verfügbar sind. • Die Option Spülstopp einzuschalten.
DEUTSCH Geben Sie das Waschmittel für die Vorwäsche in eine Dosierkugel und legen Sie diese in die Trommel. Mit dieser Option kann sich die Programmdauer verlängern. Diese beiden Optionen können nicht zusammen gewählt werden. 8.6 Spoelen+ - Rinçage+ Mit dieser Option können Sie je nach ausgewähltem Waschprogramm bis zu 3 Spülgänge hinzufügen. Die Option empfiehlt sich für Menschen, die unter Waschmittelallergien leiden, oder eine empfindliche Haut besitzen. Die Anzeige zeigt die Anzahl der Spülgänge an.
www.aeg.com • Berühren Sie die Taste bei geringerer Beladung zweimal, um ein besonders kurzes Programm einzustellen. Auf dem Display erscheint die Anzeige . Diese Option kann auch zur Verkürzung des Opfrissen Rafraîchir-Programms verwendet werden. 8.10 Taste Überspringen (Extra) Durch Berühren dieser Taste können Sie folgende Einstellungen vornehmen: • Nur Spülen bei einmaliger Berührung. Das Waschprogramm lässt die Waschphase aus und startet mit dem Spülgang.
DEUTSCH Programm Katoen - Blanc/Couleurs 23 Programmbeschreibung Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte. Das Programm Katoen - Blanc/ Couleurs bei 60 °C und das Programm Katoen - Blanc/ Couleurs bei 40 °C mit der Option sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“.
www.aeg.com Programm Programmbeschreibung ÖKOPower Baumwolle und farbechte pflegeleichte Gewebe. Waschprogramm, das in nur 59 Minuten normal verschmutzte Wäsche intensiv reinigt und eine gute Waschleistung in kurzer Zeit bietet. Anti-Allergie - Anti-Allergies 20 min.-3 kg Outdoor Weiße Baumwollwäsche. Dieses Programm beseitigt Mikroorganismen durch einen Waschgang, bei dem die Temperatur für einige Minuten auf über 60 °C gehalten wird.
DEUTSCH Programmtemperatur, maximale Schleuderdrehzahl und maximale Beladung Programm Standardtemperatur Maximale Schleuder- Maximale BelaTemperaturbereich drehzahl dung Schleuderdrehzahlbereich 40 °C 95 °C – kalt 1600 U/min 1600 U/min – 400 U/min 9 kg 40 °C Synthetica - Synthéti- 60 °C – kalt ques 1200 U/min 1200 U/min – 400 U/min 4 kg ColourPro 30 °C 30 °C – kalt 1200 U/min 1200 U/min – 400 U/min 9 kg Fijne Was - Délicats 40 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 4 kg 40 °C 40 °
www.aeg.com Fijne Was - Délicats Wol/Zijde - Laine/Soie Anti-Allergie - Anti-Allergies 20 min.
DEUTSCH 9.2 Woolmark Apparel Care Grün Das Waschprogramm Wolle dieser Maschine wurde von der Firma 27 Woolmark auf das Waschen von Wolltextilien mit der Pflegekennzeichnung „Handwäsche“ getestet und zugelassen, vorausgesetzt, dass die Wäsche gemäß der Anleitung auf dem Kleidungsetikett und gemäß den Angaben des Maschinenherstellers gewaschen wird. Beachten Sie die Trocken- und Waschanleitung auf dem Kleidungsetikett.
www.aeg.com optimieren und die Weichheit der Wäsche zu verbessern. Sie wird bei Verwendung eines Weichspülers empfohlen. Berühren Sie zum Ein-/Ausschalten dieser Option die Tasten Temp.°C und TPM gleichzeitig, bis das Symbol über der Anzeige leuchtet/erlischt. Mit dieser Option verlängert sich die Programmdauer leicht. 11. TÄGLICHER GEBRAUCH WARNUNG! Siehe Kapitel Sicherheitshinweise. 11.1 Einschalten des Geräts 1. Stecken Sie den Netzstecker in die Netzsteckdose. 2. Öffnen Sie den Wasserhahn. 3.
DEUTSCH 29 Max ▼ Max ▼ M ax ▼ ax ▼ Sa lt Sa lt M ax ▼ M ax ▼ M 2. Geben Sie das Waschpulver in das Fach . Wenn Sie Flüssigwaschmittel verwenden, siehe „Einfüllen von Flüssigwaschmittel“. Einfüllen von Flüssigwaschmittel 1. Setzen Sie den Behälter für Flüssigwaschmittel ein. Max ▼ ax ▼ ▼ M ax Max Sa lt M ▼ ax ▼ Sa lt M ax ▼ M 3. Füllen Sie bei Bedarf den Weichspüler in das Fach . 2. Geben Sie das Flüssigwaschmittel in .
www.aeg.com Die Kontrolllampe der Taste Start/Pauze - Départ Pause blinkt. Das Display zeigt die maximal zulässige Füllmenge für das Programm, die Standardtemperatur, die maximale Schleuderdrehzahl, die Programmphasen (falls verfügbar) und die voraussichtliche Programmdauer an. 2. Berühren Sie die entsprechenden Tasten, um die Temperatur und/oder Schleuderdrehzahl zu ändern. 3. Schalten Sie bei Bedarf eine oder mehrere Optionen durch Berühren der entsprechenden Tasten ein.
DEUTSCH 2. Am Ende der Beladungskennung und der Zeiterlischt die Anzeige Doppelpunkt hört auf zu blinken. Die Programmdauer wird entsprechend angepasst und kann sich verlängern oder verkürzen. Nach weiteren 30 Sekunden beginnt das Wasser einzulaufen. Falls am Ende der Beladungserkennung die Trommel überladen ist, blinkt die Anzeige im Display: In diesem Fall können Sie innerhalb von 30 Sekunden das Gerät anhalten und die überzähligen Wäschestücke entnehmen.
www.aeg.com Wurde die ProSense-Phase bereits beendet und läuft Wasser in das Gerät ein, startet das neue Programm ohne die ProSense-Phase zu wiederholen. Um Wasser und Waschmittel nicht zu verschwenden, wird das Wasser nicht abgepumpt. Das Display zeigt die maximale Programmdauer an, die etwa 20 Minuten nach dem Start des neuen Programms aktualisiert wird. 11.
DEUTSCH • Wenn Sie gewählt haben, pumpt das Gerät nur das Wasser ab. Die Optionsanzeige oder erlischt, blinkt und dann während die Anzeige erlischt. 3. Wenn das Programm beendet ist und die Türverriegelungsanzeige erlischt, können Sie die Tür öffnen. 4. Halten Sie die Taste Aan /Uit Marche/Arrêt einige Sekunden lang gedrückt, um das Gerät auszuschalten. In jedem Fall pumpt das Gerät das Wasser nach etwa 18 Stunden automatisch ab. 11.
www.aeg.com a. unterbrechen Sie das Programm und öffnen Sie die Tür (siehe „Öffnen der Tür nach erfolgtem Programmstart oder während der Zeitvorwahl“). b. verteilen Sie die Wäsche mit der Hand neu, so dass die Wäschestücke gleichmäßig verteilt sind. c. Drücken Sie die Taste Start/ Pauze - Départ Pause. Die Schleuderphase wird fortgesetzt. 12.2 Hartnäckige Flecken Für manche Flecken sind Wasser und Waschmittel nicht ausreichend.
DEUTSCH Prüfen Sie die Trommel regelmäßig auf Kalkablagerungen. Herkömmliche Waschmittel enthalten Wasserenthärtungsmittel, wir empfehlen dennoch gelegentlich ein Programm mit leerer Trommel und einem Entkalker durchzuführen. Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts. 13.
www.aeg.com ▼ Max M ax Sa lt M ax ▼ ▼ 5. Stellen Sie sicher, dass alle Waschmittelreste an der Ober- und Unterseite der Aufnahme entfernt wurden. Reinigen Sie die Schubladenaufnahme mit einer kleinen Bürste. Max ▼ ax VORSICHT! Beschädigen Sie nicht die Gummibürsten, die das Auslaufen von Waschmittel verhindern. ▼ Sa lt M ax ▼ M Max ▼ ax ▼ ax ▼ M Sa lt M 3. Reinigen Sie die Schublade und alle Einsätze unter fließendem Wasser. 6.
DEUTSCH Reinigen Sie die Ablaufpumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht. • Das Gerät macht ein ungewöhnliches Geräusch, weil die Ablaufpumpe blockiert ist. 37 4. Lassen Sie das Wasser ablaufen. • Im Display wird der Alarmcode angezeigt. WARNUNG! • Entfernen Sie das Sieb nicht, während das Gerät in Betrieb ist. • Reinigen Sie die Ablaufpumpe nicht, wenn das Wasser im Gerät heiß ist. Warten Sie, bis das Wasser abkühlt. 5.
www.aeg.com 2 1 10. Reinigen Sie das Sieb unter fließendem Wasser. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: a. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. b. Starten Sie das Programm zum Abpumpen des Wassers. 13.8 Reinigen des Siebs des Zulaufschlauchs und Ventils 11. Setzen Sie das Sieb wieder in die dafür vorgesehenen Führungen ein und drehen Sie es im Uhrzeigersinn.
DEUTSCH 39 „Reinigen des Ablauffilters“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 1. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. 2. Starten Sie das Programm zum Abpumpen des Wassers. 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 4.
www.aeg.com 14. FEHLERSUCHE WARNUNG! Siehe Kapitel Sicherheitshinweise. 14.1 Einführung Das Gerät startet nicht oder bleibt während des Betriebs stehen. Versuchen Sie zunächst, selbst eine Lösung für das Problem zu finden (siehe Tabelle). Tritt das Problem weiterhin auf, wenden Sie sich an den autorisierten Kundendienst.
DEUTSCH 41 14.2 Mögliche Störungen Störung Das Programm startet nicht. Mögliche Abhilfe • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. • Stellen Sie sicher, dass Start/Pauze - Départ Pause berührt wurde. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab oder warten Sie, bis sie abgelaufen ist.
www.aeg.com Störung Mögliche Abhilfe Das Gerät schleudert nicht oder das Waschprogramm dauert länger als gewöhnlich. • Stellen Sie das Schleuderprogramm ein. • Vergewissern Sie sich, dass das Ablaufsieb nicht verstopft ist. Reinigen Sie ggf. das Sieb. Siehe „Reinigung und Pflege“. • Verteilen Sie die Wäschestücke mit der Hand neu und starten Sie die Schleuderphase erneut. Das Problem kann durch eine Unwucht verursacht worden sein. Es befindet sich Wasser auf dem Boden.
DEUTSCH Störung Die Waschergebnisse sind nicht zufriedenstellend. 43 Mögliche Abhilfe • Erhöhen Sie die Waschmittelmenge oder benutzen Sie ein anderes Waschmittel. • Entfernen Sie vor dem Waschgang hartnäckige Flecken mit einem Spezialprodukt. • Achten Sie darauf, die richtige Temperatur einzustellen. • Verringern Sie die Beladung. • Vergewissern Sie sich, dass kein anderer Waschmitteltyp in Salt gefüllt wurde.
www.aeg.com VORSICHT! Verletzungsgefahr! Vergewissern Sie sich, dass die Trommel sich nicht dreht. Warten Sie sonst, bis die Trommel zum Stillstand gekommen ist. 14.4 Entfernen von Waschmittel oder anderen Pflegemitteln aus dem Salzfach Salt Werden versehentlich Waschmittel oder Salt Pflegemittel in das Fach gefüllt, müssen sie vollständig entfernt werden. Gehen Sie in diesem Fall folgendermaßen vor: 1. Ziehen Sie die Schublade heraus.
DEUTSCH 45 15. VERBRAUCHSWERTE Die angegebenen Werte wurden unter Laborbedingungen gemäß den einschlägigen Normen gemessen. Folgende Faktoren können diese Werte verändern: Wäscheart und -menge sowie Raumtemperatur. Der Wasserdruck, die Versorgungsspannung und die Temperatur des einlaufenden Wassers können sich auch auf die Dauer des Waschprogramms auswirken. Die technischen Daten des Produkts können auf Grund von Verbesserungen ohne vorherige Ankündigung geändert werden.
www.aeg.com Aus-Zustand (W) Ein-Zustand (W) 0.30 0.30 Die in der Tabelle oben enthaltenen Informationen erfüllen die Verordnung (EU) 1015/2010 der Kommission zur Durchführung der Richtlinie 2009/125/EG. 16.
DEUTSCH 17.3 Bausatz Wasch-TrockenSäule 47 WARNUNG! Stellen Sie den Wäschetrockner nicht unter die Waschmaschine. 17.4 Sockel mit Schublade Der Wäschetrockner kann nur mit dem von AEG hergestellten und genehmigten Bausatz Wasch-TrockenSäule auf der Waschmaschine montiert werden. Messen Sie die Tiefe Ihrer Geräte, um sich zu vergewissern, dass der Bausatz mit Ihren Geräten kompatibel ist. So steht Ihr Gerät höher und die Be- und Entladung wird einfacher.
157006651-A-132017 www.aeg.