ÖKO-LAVAMAT 84760 update The Environmentally-Friendly Washing Machine User Information
Dear customer, Please read this user information carefully. In particular, pay attention to the section ”Safety” on the first pages. Keep this user information in a safe place for later reference. Pass it on to any subsequent owners of the unit. 1 Points which are necessary for your safety or which are important for the unit's functional capability are highlighted by a warning triangle and/or signal words (Warning!, Caution!, Attention!). Always remember. 0 1.
Contents Instructions for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Environmental Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Unit Description . . . . . . . . . . . . .
Sequence of the programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Wash cycle ended/Remove washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Programme tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Separate Rinsing/Conditioner/Starching/Impregnation . . . . . . . . . . . . . .
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Water Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Permissible Water Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water Inflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instructions for use Instructions for use 1 Safety The safety of AEG electrical appliances conforms to the recognised technical regulations and the legislation covering the safety of appliances. However, as manufacturers, we still regard it as our responsibility to inform you of the following safety information. Before Putting into Operation for the First Time • Refer to the ”Installation and Connection Instructions” later in this user information.
Instructions for use Child Safety • Packaging components (e.g. films, polystyrene) can be hazardous to children. Risk of suffocation! Keep packaging away from children. • Children often cannot recognise the hazards associated with handling electrical appliances. Therefore, ensure the necessary supervision during operation and do not allow children to play with the washing machine – there is a risk that children can get trapped inside.
Instructions for use • Small animals can chew the power cables and water hoses. Risk of electric shock and danger of water damage! Keep small animals away from the washing machine. 2 Disposal Dispose the packing material! Dispose of your washing machine's packaging correctly. All the packaging materials used are harmless to the environment and can be recycled. • Plastic parts are marked with standard international abbreviations: >PE< for polyethylene, e.g. sheet wrapping material >PS< for polystyrene, e.
Instructions for use Unit Description Front View Drawer for washing detergent and care agent Control panel Rating plate (behind filling door) Filling door Screw feet (height-adjustable); rear left: Automatic adjustment foot Flap in front of solution pump Drawer for Washing Powder and Care Agent In-wash stain treatment Main detergent (powder) and water-softener if required Pre-wash detergent/ soaking agent or water-softener Liquid care agent (conditioner, finisher, starch) 9
Instructions for use Control Panel Program Button Spin speed/ progress-Display RINSE HOLD Additional programmeProgramme knob Button DOOR/LIGHT Options Multi display Button START/ PAUSE Button DELAY TIMER Display OVERDOSING Programme knob The programme knob determines the type of the washing cycle (e. g. water level, drum movement, number of rinse cycles, spinspeed) depending on the type of washing to be handled, as well as the water temperature.
Instructions for use COTTONS/LINEN, EASY-CARE (WITTE/BONTE WAS, BLANC/COULEURS, KREUKHERSTELLEND, DEFROISSABLE) Wash programme from 20 °C to95 °C can be used universally for cotton/linen, easy-care (e.g. cotton/polyester) and synthetics. The washing programme adapts itself to the various types of types of weaves and amount of filling. For mostly cotton/linen, the programme for cotton/ linen will be carriedout; for mostly synthetics, a programme for easycare washing.
Instructions for use SILK (ZIJDE, SOIE)/ P (handwash) Wash programme at 30 °C for hand- and machine-washable silk. 3 As silk is a very delicate textile, we recommend washing only one article of clothing, if possible, and on no account washing it together with other textiles. For extremely delicate silk textiles, it is possible to obtain an even more gentle handling by using the TIME SAVE button.
Instructions for use DELICATE (BEHOEDZAAM, SENSITIVE) Special additional programme with significantly higher rinse effect (special spin cycle) with simultaneously improved weave care (reduced drum movement). Ideal, if washing is to be carried out often, e.g. for over-sensitive skin. RINSE+ (SPOELEN+, RINCAGE+) can additionally be selected. STAINS (VLEKKEN, TACHES) For handling strongly soiled or stained washing. (Stainssalt or tabs are rinsed in a time optimized manner during the programme cycle).
Instructions for use Consumption values and time requirements The values for selected programmes in the following table were determined under normal conditions. Besides the selected settings (additional functions), the consumption values also depend on other conditions such as water temperature or the washing powder/liquid used.
Instructions for use Wash Time Display 3 The wash times for the wash programmes depend on the usual washing practice and the ambient conditions at the place of installation. The washing type and quantity, the type of washing detergent, the water temperature and the room temperature etc. can influence the duration of the wash programme.
Instructions for use What does “UPDATE” mean? The wash programmes in your washing machine are controlled by software. New types of fabric or new detergents may require new wash programmes in the future. In most cases, the software can be adapted to this. For further information on a possible “update” please contact customer service. Water Protection Aqua Control + Aqua Alarm In the event of damage to the supply hose, the system blocks the further supply of water to the unit directly st the water tap.
Instructions for use Before the first wash 0 Carry out a wash cycle without washing; Programme COTTON/LINEN (WITTE/BONTE WAS, BLANC/COULEURS) 95, with half the washing powder/liquidquantity. In this way, manufacturing remains in the drum and water container will be removed. Preparing a Wash Load Sorting and preparing a wash load • Sort the washing according to care symbol (see “Washing Types and Care Symbols”). • Empty all pockets. • Remove metal objects (paper clips, safety pins etc.).
Instructions for use Types of washing and care symbols The care symbols help in the selection of the correct wash programmes. The washing should be sorted according to type and care symbols. The temperature information on the care symbols are always maximum values. Cottons ç Textiles of Cotton and Linens with this care symbol are resistant to mechanical loading and high temperatures.
Instructions for use Washing Detergents and Care Agents Which washing detergent and care agent? Use only washing detergents and care agents which are suitable for use in washing machines. Always follow the manufacturer's instructions.
Instructions for use Carrying out a wash cycle Brief instructions A wash cycle is carried out in the following steps: 0 1. Setting the correct wash programme: – Set programme and temperature with the programme knob, – If necessary, select additional programme. 2. PossiblyChange spin speed, select /RINSE STOP (GEEN CENTR., SANS ESSOR.). 3. Possibly set DELAY TIMER (STARTTIJDKEUZE, DEPART DIFFERE). 4. Open door, put in washing, 5. Close door. 6. Washing-/Add conditioner. 7.
Instructions for use Setting the wash programme 3 For suitable programme, correct temperature and possible additional programs for the respective type of washing, see „Programme tables“. 0 1. With the programme knob, set the desired wash programme and temperature. In the multi-display the probable duration of the set programmes will be shown in minutes. 2. Possible Press additional programme button(s): The display of the selected additional programme is displayed.
Instructions for use Change Spin Speed / Select Rinse Hold 0 If necessary, change the spin speed for the final spin / select RINSE HOLD (GEEN CENTR., SANS ESSOR.): Press the button Spin speed/RINSE HOLD (GEEN CENTR., SANS ESSOR.) as often as necessary until the display for the required spin speed (or of RINSE HOLD/GEEN CENTR., SANS ESSOR.) lights up. If RINSE HOLD (GEEN CENTR., SANS ESSOR.) is selected, the washing remains in the last rinsing water and is not spun.
Instructions for use Setting the delay timer/soaking time Delay timer The DELAY TIMER (STARTTIJDKEUZE, DEPART DIFFERE) button makes it possible to delay the start of a wash programme by 1 to a maximum of 19 hours. 0 1. Select wash programme. 2. Press DELAY TIMER (STARTTIJDKEUZE, DEPART DIFFERE) button. 3. Press START/PAUSE (START/PAUZE, MARCHE /PAUSE) button. With a delay in the start, the DELAY TIMER (STARTTIJDKEUZE, DEPART DIFFERE) display lights up.
Instructions for use Opening and Closing the Filling Door 0 0 3 Open: Press the button DOOR/LIGHT (DEUR/ LICHT, PORTE/ECLAIR.). The filling door springs open. Close: Press the filling door firmly closed. When the unit is switched on, the display DOOR/LIGHT (DEUR/LICHT, PORTE/ECLAIR.
Instructions for use Add Washing Detergent/Care Agent For information on wash and care agent, see chapter „Washing powder and care agent“. 0 1. Open the washing detergent drawer: Reach into the flap at the bottom of the drawer (1), pull drawer out up to the stop (2). 2. Fill with washing detergent/care agent.
Instructions for use Starting the wash program 0 1. Checking whether the water tap is open. 2. Starting the wash programme: Press the START/PAUSE (START/PAUZE, MARCHE /PAUSE) button. The wash programme is started or starts after end of the set delay time. 3 If the DOOR/LIGHT (DEUR/LICHT, PORTE/ECLAIR.) display lights up red when pressing the START/PAUSE (START/PAUZE, MARCHE /PAUSE) button, then the door is not properly closed.
Instructions for use Sequence of the programme Programme sequence - display Before the start, the programme steps to be carried out will be displayed by the Programme sequence display. During the washing cycle, the current programme step is displayed. Multi display The expected The remaining wash time (in minutes) up to the programme end is displayed in the Multi display.
Instructions for use Wash cycle ended/Remove washing After the wash programme has been ended, END (EINDE, FIN) is displayed on the Programme cycle display. • If programme EASY IRON (STRIJKVRIJ, SANS REPASSAGE) has been selected, then a crease guard programme of ca. 30 minutes is carried out after the programme end. The multi-display then additionally shows a rest time of 1 minute and the display END (EINDE, FIN) lights up.
Instructions for use 3 If the display OVER DOSING (OVERDOS., SURDOSAGE) lights up, too much washing detergent was used in the washing program just ended. During the next wash, pay attention to the dosing information of the washing detergent manufacturer and pay attention to the filling quantity! Attention! If the washing machine is not used for a long time: Close the water tap and disconnect the washing machine from the electricity mains.
Instructions for use Programme tables Wash In the following, there are shown, not all the possible, but only the commonly used and best settings. Type of washing, Cleaning symbol Cotton/linen3) èç Cotton/Linen ëèç 30 max. Filling quantity1) (dryweight)2) Programme knob temperature [in °C] possible Additional programmes 6kg ENERGY SAVING 60 (ENERGIEBESPAREN, ECONOMIQUE) PRE WASH (VOORWAS, PRELAV.
Instructions for use Type of washing, Cleaning symbol max. Filling quantity1) (dryweight)2) Programme knob temperature [in °C] COTTON/LINEN, EASY-CARE (WITTE/BONTE WAS, BLANC/COULEURS, KREUKHERSTELLEND, DEFROISSABLE) 20 to 60 PRE WASH (VOORWAS, PRELAV.) DELICATE (BEHOEDZAAM, SENSITIVE) STAINS (VLEKKEN, TACHES) TIME SAVE 1kg EASY IRON (STRIJKVRIJ, SANS REPASSAGE)4) 40 PRE WASH (VOORWAS, PRELAV.) STAINS (VLEKKEN, TACHES) TIME SAVE 3kg REFRESH (OPFRISSEN, RAFRAICHIR) 30 3kg (or.
Instructions for use Separate Rinsing/Conditioner/Starching/Impregnation Max. Filling quantity (dry weight) Programme knob Cotton-/Linen 6kg RINSING (SPOELEN, RINCAGE) Wool/Hand wash programme 2kg RINSE (SPOELEN, RINCAGE) + button TIME SAVE Type of washing Separate Spinning Type of washing 32 Max. Filling quantity (dry weight) Cotton-/Linen 6kg Easy-care 3kg Delicates 3kg Wool/Hand wash programme 2kg Silk 1kg Programme knob SPIN (CENTRIFUG., ESSORAGE) SHORT SPIN (KORT CENTRIFUG.
Instructions for use Cleaning and Care Control Panel 0 Attention! For cleaning panels and control parts, do not use furniture polish or any aggressive cleaning agents. Wipe off control panels with a damp cloth. Use warm water to do this. Washing Detergent Drawer The washing detergent drawer should be cleaned from time to time. 0 1. Pull out the washing detergent drawer as far as it will go. 2. Remove the washing detergent drawer with a firm pull. 3.
Instructions for use 7. Use a brush to clean the entire rinsing-in part of the washing machine, especially the nozzles on the top side of the rinsing-in chamber. 8. Insert the washing detergent drawer into the guide rails and push it in. Washing Drum 0 The washing drum is made of high-quality stainless steel. Rust deposits on the drum can occur due to foreign bodies in the washing which can cause rust.
Instructions for use What to do if ... Remedying Faults In the event of a fault, try to solve the problem yourself with the aid of the information provided here. If you call Customer Service to deal with one of the faults listed here or to remedy an operating fault, the customer service technician's visit will not be free of charge, even during the warranty period. • It the fault code C1 or C2 appears in the multi display, you may be able to remedy the fault yourself (see the fault table below).
Instructions for use Problem Possible cause Water tap is switched Off Water is not entering. Error code (1 appears. Remedy Open water tap. Close water tap. Disconnect Filter in the socket of the inhose from water tap, remove flow hose connection is filterand clean under blocked. running water. Water tap is full of lime or defective. Check water tap, if necessary have it repaired. Transport safeguard has not been removed. Remove transport safeguard according to setting up and connection instructions.
Instructions for use Problem Water leaks out of the washing machine. Possible cause Remedy Connection to the inflow hose is leaking. Tighten inflow hose connection. Drainage hose is leaking. Check drainage hose and, if necessary, replace. Cover of the water pump is not properly closed. Close cover properly. Washing is jammed in the door. Abort programme, remove washing from door. Start programme again. Emergency emptying hose is not properly closed off or is leaking.
Instructions for use Problem Possible cause Remedy There is a kink n the drainage Remove kink. hose. Maximum pump height (emptying height 1m from Washing is not spun. base surface of the appliRemaining water is vis- ance) is exceeded. iblein the drum. Error code (2 appears. Water pump is blocked. Refer to the customer service. For pumping heights over 1m, they have a supplementary set as special spares available. Switch off appliance and pull out electric plug. Clean water pump.
Instructions for use If the washing result is not satisfactory If the washing is grey and limescale forms in the drum • Not enough washing detergent added. • The right washing detergent was not used. • Special types of stain were not pretreated. • Program or temperature incorrectly set. • If binary wahing detergents were used, the individual components were not added in the correct ratio.
Instructions for use Carry Out an Emergency Emptying Operation • When the washing machine no longer pumps off the washing solution, an emergency emptying operation must be carried out. • When the washing machine is in a room where there is a frost risk, an emergency emptying operation must be carried out when there is a frost risk. Also: Unscrew the intake hose from the water tap and lay it on the floor. Empty the drainage hose.
Instructions for use When all the washing solution has drained off: 6. Firmly push the plug into the emergency emptying hose and turn it tight clockwise. 7. Put the emergency emptying hose back into the holder. 8. Insert the flap into the base panel and close. Drain pump The drain pump is maintenance free. The cover of the drain pump must only opened in the event of a malfunction when no more water is being pumped out, e.g. if the pump is blocked.
Instructions for use 5. Replace the pump cover. Laterally insert the webs on the cover into the guide slots and screw on the cover in a clockwise direction. 6. Close the emergency emptying hose and place it in the holder. 7. Close the flap. Emergency Unlocking of the Filling Door When the filling door can no longer be opened, it can be opened with the aid of the emergency unlocking facility.
Instructions for use Additional rinse cycle (RINCAGE+) The washing machine is set to very economical water consumption. However for people who suffer from an allergy, it can be helpfulto rinse with more water. 3 When this function is set, an additional rinse takes place for the programmes COTTON/LINEN , EASY-CARE (WITTE/BONTE WAS, BLANC/ COULEURS, KREUKHERSTELLEND, DEFROISSABLE) as well as EASY IRON (STRIJKVRIJ, SANS REPASSAGE) and DELICATES (FIJNE WAS, LINGE DELICAT).
Instructions for use Cancel additional rinse cycle 0 1. Turn programme knob to SHORT SPIN (KORT CENTRIFUG., ESSORAGE DELICAT). 2. Keep button DELICATES (BEHOEDZAAM, SENSITIVE) depressed for at least 5 seconds. Immediately on pressing the button, RINSE+ (SPOELEN+, RINCAGE+) blinks on the programme cycle display. After 5 seconds RINSE+ (SPOELEN+, RINCAGE+) will stop blinking and lights up constantly for a further 5 seconds. 3.
Instructions for use 4. if you want to check whether the water cooling is set: – Turn the programme knob to SHORT SPIN (KORT CENTRIFUG., ESSORAGE DELICAT). – Press the PRE WASH (VOORWAS, PRELAV.) button briefly. If the MAIN WASH (HOOFDWAS, LAVAGE) blinks on the programme cycle display, then the water cooling is set. Cancel water cooling: 0 1. Turn programme knob to SHORT SPIN (KORT CENTRIFUG., ESSORAGE DELICAT). 2. Keep the PRE WASH (VOORWAS, PRELAV.) button depressed for at least 5 seconds.
Instructions for use Variomatic-loose spinning Adjustable spin integrated into the end spin. The washing adheres less to the drum wall and can be removed easier. Can be selected to COTTON/LINEN, EASY-CARE (WITTE/BONTE WAS, BLANC/ COULEURS, KREUKHERSTELLEND, DEFROISSABLE). Set loose spin: 0 1. Turn programme knob to SHORT SPIN (KORT CENTRIFUG., ESSORAGE DELICAT). 2. Keep button STAINS (VLEKKEN, TACHES) depressed for at least 5 seconds.
Instructions for use Programme security In order to secure a programme from undesirable changes (e. g. Overrotating programme knob, additional pressing of buttons, etc.), it is possible to set the programme security. This will prevent damage to your washing. 3 Setting and releasing the Programme security is possible at any time during a programme. Setting programme security: 0 1. Set the desired washing programme. 2. Press the START/PAUSE (START/PAUZE, MARCHE/PAUSE) button to start the programme. 3.
Instructions for use Child Safety Feature When the child safety feature is used, the filling door can no longer be closed and no more washing programs can be started. 0 1 0 48 Setting the Child Safety Feature: Use a coin to turn the rotary knob (on the inside of the filling door) clockwise as far as it will go. Warning! The rotary knob must not be pressed in following adjustment, otherwise the child safety feature is not active. The rotary knob must project as shown in the diagram.
Setting up and connection instructions Setting up and connection instructions Safety Instructions for Installation • Do not tilt the washing machine onto its front or onto its right side (looking from the front). Electrical components could get wet! • Check the washing machine for transport damage. Never connect a damaged unit. Consult your supplier in the event of damage.
Setting up and connection instructions Setting Up the Unit 3 Washing machines with curved panels are not suitable for substructures. Transporting the Unit • Do not place the washing machine on its front side or on its right side (looking from the front). Otherwise the electrical components can get wet. • Never transport the unit without using the transport safeguard. Do not remove the transport safeguard until you reach the installation site.
Setting up and connection instructions 2. Firmly pull both hose holders off the unit. 3 The special button A and the plug caps B (2 ea.) and C (1 ea.) are supplied with the unit. 3. Remove the screw D, including the compression spring with the special button A. 4. Close off the hole with the plug cap C. Attention! Push in the plug cap so firmly that it engages in the rear panel (this protects the inside of the unit against splash water). 5. Unscrew the two screws E using the special button A. 6.
Setting up and connection instructions Prepare the Installation Location • The installation surface must be clean, dry and free of floor wax residue and other lubricating coatings so that the unit does not slide away. Do not use any lubricants as sliding aids. • It is not recommended to set up the washing machine on deep-pile carpets or on floor coverings with soft foam underlays, as this would mean that the stability of the unit would not be guaranteed.
Setting up and connection instructions Compensate for Floor Unevenness Automatic Adjustment Foot: Your washing machine's rear left foot is of a spring leg design. This guarantees good stability of the unit, even at high spinning speeds. If the washing machine still does not stand firmly enough during spinning, proceed as follows: 0 1. Adjust the three adjustment feet to the setpoint 10mm. To do this, use the supplied special button to remove the transport safeguard.
Setting up and connection instructions Electrical Connection Refer to the rating plate for details of the mains voltage, current type and the necessary fuses. The rating plate is located at the top behind the filling door.
Setting up and connection instructions Water Inflow A pressure hose 1.5m in length is supplied. If a longer inflow hose is required, only a VDE-approved, complete set of hoses with fitted hose screw connections offered by our Customer Service is permissible. – Sets of hoses in lengths of 2.2m, 3.5m and 5m are available for washing machines without Aqua-Control. – Sets of hoses in lengths of 2.0m, 2.9m and 3.9m are available for washing machines with Aqua-Control.
Setting up and connection instructions Water Drainage The drainage hose can either be connected to a siphon or hung in a wash basin or bath tub. Only original hoses may be used for extension purposes (max. 3m on the floor and then up to 80cm high). The Customer Service stocks hoses in lengths of 2.7 and 4m. Attention! It is absolutely essential to install the drainage hose free of pinches. 0 Water Drainage into a Siphon The grommet on the end of the hose fits all commonly used siphon types.
Setting up and connection instructions Delivery Heads over 1m To pump off the washing / rinsing agent, every washing machine has a pump which transports liquids via the drainage hose up to a height of 1m, calculated from the machine's floor. For delivery heads over 1m, consult the Customer Service.
Technical Data Height adjustment Filling quantity (program-dependent) Use Drum speed, spin Water pressure Dimensions (Measurements in mm) 58 Approx. +10/-5mm max. 6kg Domestic see rating plate 1-10bar (=10–100N/cm2 = 0.1–1.
Guarantee conditions Guarantee conditions Belgium DECLARATION OF GUARANTEE TERMS. Our appliances are produced with the greatest of care. However, a defect may still occur. Our consumer services department will repair this upon request, either during or after the guarantee period. The service life of the appliance will not, however, be reduced as a result. This declaration of guarantee terms is based on European Union Directive 99/44/EC and the provisions of the Civil Code.
Guarantee conditions 12. If, during the guarantee period, repairing the same defect repeatedly is not conclusive, or if the repair costs are considered disproportionate, in agreement with the consumer, the defective appliance may be replaced with another appliance of the same value. In this event, we reserve the right to ask for a financial contribution calculated according to the length of time it has been used. 13.
Customer services Customer services Belgium Tel.: Electrolux Home Products Belgium ELECTROLUX SERVICE Bergensesteenweg 719 1502 Lembeek Province de Liège: S.D.E. Rue Gaucet 26 4020 Liege Fax.: Consumer services 02/363.04.44 02/363.04.00 02/363.04.60 04/343.11.60 04/343.47.
Index Index A Aborting the programme . . . . . . . . . . . . . . Additional programme - buttons . . . .12, Aqua Control . . . . . . . . . . . . . . . . . 16, 29, Automatic adjustment foot . . . . . . . . . . 9, O 27 30 37 53 C Care agent . . . . . . . . . . . . . . . . . . . . 9, 19, Child safety feature . . . . . . . . . . . . . . .35, Conditioner . . . . . . . . . . . . . . . . 9, 11, 20, Correcting the programme . . . . . . . . . . . . Cottons . . . . . . . . . . . . . . . . . . . . . .
Service Service In the section ”What to do if ...” there is a list of some faults which you can remedy yourself. Look there first if a fault occurs. If you find no information there, please consult your Customer Service Centre. Always prepare in advance for the discussion. By doing so you will simplify the diagnosis and the decision on whether customer service is necessary. Note the PNC-number and the S-number. Both can be found on the rating plate on the inside of the door on your washing machine. PNC ...
From the Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.
