ÖKO-LAVAMAT 85749 updatee The Environmentally-Friendly Washing Machine User Information
Dear customer, Please read this user information carefully. In particular, pay attention to the section ”Safety” on the first pages. Keep this user information in a safe place for later reference. Pass it on to any subsequent owners of the unit. 1 Points which are necessary for your safety or which are important for the unit's functional capability are highlighted by a warning triangle and/or signal words (Warning!, Caution!, Attention!). Always remember. 0 1.
Contents Instructions for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Environmental Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Unit Description . . . . . . . . . . . . .
Sequence of the programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Wash cycle ended/Remove washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Programme tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Separates Rinsing/Conditioner/Starching/Impregnation . . . . . . . . . . . . .
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Water Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Permissible Water Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water Inflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instructions for use Instructions for use 1 Safety The safety of AEG electrical appliances conforms to the recognised technical regulations and the legislation covering the safety of appliances. However, as manufacturers, we still regard it as our responsibility to inform you of the following safety information. Before Putting into Operation for the First Time • Refer to the ”Installation and Connection Instructions” later in this user information.
Instructions for use Child Safety • Packaging components (e.g. films, polystyrene) can be hazardous to children. Risk of suffocation! Keep packaging away from children. • Children often cannot recognise the hazards associated with handling electrical appliances. Therefore, ensure the necessary supervision during operation and do not allow children to play with the washing machine – there is a risk that children can get trapped inside.
Instructions for use 2 Disposal Dispose the packing material! Dispose of your washing machine's packaging correctly. All the packaging materials used are harmless to the environment and can be recycled. • Plastic parts are marked with standard international abbreviations: >PE< for polyethylene, e.g. sheet wrapping material >PS< for polystyrene, e.g. padding material (always CFC-free) >POM< for polyoxymethylene, e.g.
Instructions for use Unit Description Front View Drawer for washing powder and care agent Control panel Rating plate (behind filling door) Filling door Screw feet (height-adjustable); rear left: Automatic adjustment foot Flap in front of solution pump Drawer for Washing Powder and Care Agent In-wash stain treatment Main detergent (powder) and water-softener if required Pre-wash detergent/ soaking agent or water-softener Liquid care agent (conditioner, finisher, starch) 9
Instructions for use Control Panel Program Button Spin speed/ progress-Display RINSE HOLD Additional programmeProgramme knob Button DOOR/LIGHT Options Multi display Button START/ PAUSE Button DELAY TIMER Display OVERDOSING Programme knob The programme knob determines the type of the washing cycle (e. g. water level, drum movement, number of rinse cycles, spinspeed) depending on the type of washing to be handled, as well as the water temperature.
Instructions for use linen will be carriedout; for mostly synthetics, a programme for easycare washing. For purely easy-care loading, the amount of filling should not exceed 2.5 kg in order to prevent increased creasing build-up. STARCHING (STÄRKEN, AMIDON.) Separate rinse, separate Conditioning, separate impregnation of wet washing (1 rinse cycle, fluid conditioner from the compartment æ is rinsed in, spin). Do not pour conditioner into the compartment if a separate spin cycle is to be carried out.
Instructions for use REFRESH (AUFFRISCHEN, RAFRAICHIR) Ca. 20-minute special programme at 30 °C for short wash cycle washing of textiles, such as sports clothing that has only been worn once and is only lightly soiled. EASY IRON (LEICHTBÜGELN, FACILE A REPASSER) Wash programme at 40 °C for easy-care textiles that will only need to be lightly ironed or not at all after this programme. 2 ENERGY SAVING (ENERGIESPAREN, ECONOMIQUE) Special energy and water saving programme at ca.
Instructions for use ECO TIME (ZEIT SPAREN, ECO TIME) Shortened washing programme for less soiled washing can be selected in three levels for the programme COTTON/LINEN, EASY CARE (KOCH/ BUNT, PFLEGELEICHT, BLANC/COULEURS, TEXTILES MELANGES) and in two levels for other programmes.
Instructions for use Consumption values and time requirements The values for selected programmes in the following table were determined under normal conditions. Besides the selected settings (additional functions), the consumption values also depend on other conditions such as water temperature or the washing powder/liquid used.
Instructions for use Wash Time Display 3 The wash times for the wash programmes depend on the usual washing practice and the ambient conditions at the place of installation. The washing type and quantity, the type of washing detergent, the water temperature and the room temperature etc. can influence the duration of the wash programme. What does “UPDATE” mean? The wash programmes in your washing machine are controlled by software.
Instructions for use Preparing a Wash Load Sorting and preparing a wash load • Sort the washing according to care symbol (see “Washing Types and Care Symbols”). • Empty all pockets. • Remove metal objects (paper clips, safety pins etc.). • In order to prevent the washing tangling and being damaged: close zippers, button up duvet covers and pillow cases, and tie up loose straps such as from aprons. • Turn articles with double layered fabric inside out (sleeping bags, anoraks etc.).
Instructions for use Types of washing and care symbols The care symbols help in the selection of the correct wash programmes. The washing should be sorted according to type and care symbols. The temperature information on the care symbols are always maximum values. Cottons ç Textiles of Cotton and Linens with this care symbol are resistant to mechanical loading and high temperatures.
Instructions for use Washing Detergents and Care Agents Which washing detergent and care agent? Use only washing detergents and care agents which are suitable for use in washing machines. Always follow the manufacturer's instructions.
Instructions for use Carrying out a wash cycle Brief instructions A wash cycle is carried out in the following steps: 0 1. Setting the correct wash programme: – Set programme and temperature with the programme knob, – If necessary, select additional programme. 2. PossiblyChange spin speed, select /RINSE STOP (SPÜLSTOPP, ARR. CUVE PL.). 3. Possibly set DELAY TIMER (ZEITVORWAHL, DEPART DIFFERE). 4. Open door, put in washing, 5. Close door. 6. Washing-/Add conditioner. 7.
Instructions for use Setting the wash programme 3 For suitable programme, correct temperature and possible additional programs for the respective type of washing, see „Programme tables“. 0 1. With the programme knob, set the desired wash programme and temperature. In the multi-display the probable duration of the set programmes will be shown in minutes. 2. Possible Press additional programme button(s): The display of the selected additional programme is displayed.
Instructions for use Change Spin Speed / Select Rinse Hold 0 If necessary, change the spin speed for the final spin / select RINSE HOLD (SPÜLSTOPP, ARR. CUVE PL.): Press the button Spin speed/RINSE HOLD (SPÜLSTOPP, ARR. CUVE PL.) as often as necessary until the display for the required spin speed (or of RINSE HOLD/SPÜLSTOPP, ARR. CUVE PL.) lights up. If RINSE HOLD (SPÜLSTOPP, ARR. CUVE PL.) is selected, the washing remains in the last rinsing water and is not spun.
Instructions for use Setting the delay timer/soaking time Delay timer The DELAY TIMER (ZEITVORWAHL, DEPART DIFFERE) button makes it possible to delay the start of a wash programme by 1 to a maximum of 19 hours. 0 1. Select wash programme. 2. Press DELAY TIMER (ZEITVORWAHL, DEPART DIFFERE) button. 3. Press START/PAUSE (START/PAUSE, MARCHE /PAUSE) button. With a delay in the start, the DELAY TIMER (ZEITVORWAHL, DEPART DIFFERE) display lights up.
Instructions for use Opening and Closing the Filling Door 0 0 3 Open: Press the button DOOR/LIGHT (TÜR/LICHT, PORTE/LUMIERE). The filling door springs open. Close: Press the filling door firmly closed.
Instructions for use Add Washing Detergent/Care Agent For information on wash and care agent, see chapter „Washing powder and care agent“. 0 1. Open the washing detergent drawer: Reach into the flap at the bottom of the drawer (1), pull drawer out up to the stop (2). 2. Fill with washing detergent/care agent.
Instructions for use Starting the wash program 0 1. Checking whether the water tap is open. 2. Starting the wash programme: Press the START/PAUSE (START/PAUSE, MARCHE /PAUSE) button. The wash programme is started or starts after end of the set delay time. 3 If the DOOR/LIGHT (TÜR/LICHT, PORTE/LUMIERE) display lights up red when pressing the START/PAUSE (START/PAUSE, MARCHE /PAUSE) button, then the door is not properly closed.
Instructions for use Sequence of the programme Programme sequence - display Before the start, the programme steps to be carried out will be displayed by the Programme sequence display. During the washing cycle, the current programme step is displayed. Multi display The expected remaining wash time (in minutes) up to the programme end is displayed in the Multi display.
Instructions for use Wash cycle ended/Remove washing After the wash programme has been ended, END (ENDE, FIN) is displayed on the Programme cycle display. • If programme EASY IRON (LEICHTBÜGELN, FACILE A REPASSER) has been selected, then a crease guard programme of ca. 30 minutes is carried out after the programme end. The multi-display then additionally shows a rest time of 1 minute and the display END lights up.
Instructions for use washing program just ended. During the next wash, pay attention to the dosing information of the washing detergent manufacturer and pay attention to the filling quantity! Attention! If the washing machine is not used for a long time: Close the water tap and disconnect the washing machine from the electricity mains. (Aqua Control water protection with Aqua Alarm does not operate if the power supply is interrupted.
Instructions for use Programme tables Wash In the following, there are shown, not all the possible, but only the commonly used and best settings. Type of washing, Cleaning symbol Cotton/linen1) èç max. Filling quantity (dryweight)1) Programme knob temperature [in °C] possible Additional programmes PRE WASH (VORWÄSCHE, PRELAV.
Instructions for use Type of washing, Cleaning symbol max. Filling quantity (dryweight)1) 2,5kg Easy-care2) î íê Delicates ì Programme knob temperature [in °C] PRE WASH (VORWÄSCHE, COTTON/LINEN, EASY-CARE PRELAV.) SENSITIVE (KOCH/BUNT, (SENSITIV, SENSITIVE) PFLEGELEICHT, STAINS BLANC/COULEURS, (FLECKEN, TACHES) TEXTILES MELANGES) ECO TIME 20 to 60 (ZEIT SPAREN, ECO TIME) 1kg EASY IRON (LEICHTBÜGELN, FACILE A REPASSER)2) 40 2.5kg REFRESH (AUFFRISCHEN, RAFRAICHIR)30 2.5kg (or.
Instructions for use Separates Rinsing/Conditioner/Starching/Impregnation Max. Filling quantity (dry weight) Programme knob Cotton-/Linen 5kg STARCHING (STÄRKEN, AMIDON.) Wool/Hand wash programme 2kg STARCHING (STÄRKEN, AMIDON.) + button ECO TIME (ZEIT SPAREN, ECO TIME) Type of washing Separates Spinning Type of washing Cotton-/Linen Max. Filling quantity (dry weight) 5kg Easy-care 2.5kg Delicates 2.
Instructions for use Cleaning and Care Control Panel 0 Attention! For cleaning panels and control parts, do not use furniture polish or any aggressive cleaning agents. Wipe off control panels with a damp cloth. Use warm water to do this. Washing Detergent Drawer The washing detergent drawer should be cleaned from time to time. 0 1. Pull out the washing detergent drawer as far as it will go. 2. Remove the washing detergent drawer with a firm pull. 3.
Instructions for use 7. Use a brush to clean the entire rinsing-in part of the washing machine, especially the nozzles on the top side of the rinsing-in chamber. 8. Insert the washing detergent drawer into the guide rails and push it in. Washing Drum 0 The washing drum is made of high-quality stainless steel. Rust deposits on the drum can occur due to foreign bodies in the washing which can cause rust.
Instructions for use Cleaning the drain pump Paper clips, nails and so on can sometimes get into the washing machine with the washing and remain in the drain pump casing. Fluff and strands of fabric can gather on these items and block the drain pump. Therefore the drain pump should be cleaned at least once a year. Warning! Switch off the washing machine and pull out the mains plug before cleaning the drain pump! 0 1. First carry out an emergency emptying (see section ”Carry Out Emergency Emptying”). 2.
Instructions for use What to do if ... Remedying Faults In the event of a fault, try to solve the problem yourself with the aid of the information provided here. If you call Customer Service to deal with one of the faults listed here or to remedy an operating fault, the customer service technician's visit will not be free of charge, even during the warranty period. • It the fault code C1 or C2 appears in the multi display, you may be able to remedy the fault yourself (see the fault table below).
Instructions for use Problem Possible cause Remedy Transport safeguard has not been removed. Remove transport safeguard according to setting up and connection instructions. The height adjustable threaded feet are not correctly adjusted. Align feet according to setting up and connection instructions. Washing machine viThere is very little washing in brates during operation the drum (e.g. only a dressing Function is not affected by this. or is unsteady. gown).
Instructions for use Problem Conditioner has not rinsed, compartment æ for care agent is filled with water. Washing is badly creased. Possible cause Remedy Conditioner insert in the compartment for care agent is not properly placed on or is blocked. Clean detergent drawer, seat conditioner insert properly. Probably too much washing has been put in. Note maximum filling quantity (see programme tables). For easy-care textiles select the EASY IRON (LEICHTBÜGELN, FACILE A REPASSER) programme.
Instructions for use Problem Possible cause Remedy When pressing an additional programme but- The selected additionalproton, the gramme cannot be combined Make another selection. correspondingdisplay with the set programme. does not light up. Programme cycledisplay blinks constantly. Programme security is switched On; during the wash cycle the programme knob has been moved. Turn programme knob back to its original position (see „Programme security“).
Instructions for use Carry Out an Emergency Emptying Operation • When the washing machine no longer pumps off the washing solution, an emergency emptying operation must be carried out. • When the washing machine is in a room where there is a frost risk, an emergency emptying operation must be carried out when there is a frost risk. Also: Unscrew the intake hose from the water tap and lay it on the floor. Empty the drainage hose.
Instructions for use When all the washing solution has drained off: 6. Firmly push the plug into the emergency emptying hose and turn it tight clockwise. 7. Put the emergency emptying hose back into the holder. 8. Insert the flap into the base panel and close. Emergency Unlocking of the Filling Door When the filling door can no longer be opened, it can be opened with the aid of the emergency unlocking facility.
Instructions for use Additional rinse cycle (RINSE+/ SPÜLEN+, RINCAGE+) The washing machine is set to very economical water consumption. However for people who suffer from an allergy, it can be helpfulto rinse with more water. 3 When this function is set, an additional rinse takes place for the programmes COTTON/LINEN , EASY-CARE (KOCH/BUNT, PFLEGELEICHT, BLANC/COULEURS, TEXTILES MELANGES) as well as EASY IRON (LEICHTBÜGELN, FACILE A REPASSER) and DELICATES (FEINWÄSCHE, DELICAT).
Instructions for use Cancel additional rinse cycle 0 1. Turn programme knob to SHORT SPIN (SCHONSCHLEUDERN, ESSORAGE DELICAT). 2. Keep button DELICATES (FEINWÄSCHE, DELICAT) depressed for at least 5 seconds. Immediately on pressing the button, RINSE+ (SPÜLEN+, RINCAGE+) blinks on the programme cycle display. After 5 seconds RINSE+ (SPÜLEN+, RINCAGE+) will stop blinking and lights up constantly for a further 5 seconds. 3.
Instructions for use Water cooling It may be necessary to cool the wash water before pumping out in order to prevent damage to plastics draining pipes. 3 The wash water is cooled before pumping out at the end of the main wash cycle (by the addition of cold water). (This setting is only effective for the programme COTTON/LINEN, EASY-CARE (KOCH/BUNT, PFLEGELEICHT, BLANC/COULEURS, TEXTILES MELANGES) with a temperature over 40 °C.
Instructions for use Cancel water cooling: 0 1. Turn programme knob to SHORT SPIN (SCHONSCHLEUDERN, ESSORAGE DELICAT). 2. Keep the PRE WASH (VORWÄSCHE, PRELAV.) button depressed for at least 5 seconds. Immediately after the button is pressed, MAIN WASH (HAUPTWÄSCHE, LAVAGE) will blink on the programme cycle display. After 5 seconds MAIN WASH (HAUPTWÄSCHE, LAVAGE) will stop blinking and will remain lit constantly for 5 seconds. 3.
Instructions for use Variomatic-loose spinning Adjustable spin integrated into the end spin. The washing adheres less to the drum wall and can be removed easier. Can be selected to COTTON/LINEN, EASY-CARE (KOCH/BUNT, PFLEGELEICHT, BLANC/COULEURS, TEXTILES MELANGES). Set loose spin: 0 1. Turn programme knob to SHORT SPIN (SCHONSCHLEUDERN, ESSORAGE DELICAT). 2. Keep button STAINS (FLECKEN, TACHES) depressed for at least 5 seconds.
Instructions for use Programme security In order to secure a programme from undesirable changes (e. g. Overrotating programme knob, additional pressing of buttons, etc.), it is possible to set the programme security. This will prevent damage to your washing. 3 Setting and releasing the Programme security is possible at any time during a programme. Setting programme security: 0 1. Set the desired washing programme. 2. Press the START/PAUSE (START/PAUSE, MARCHE/PAUSE) button to start the programme. 3.
Instructions for use Child Safety Feature When the child safety feature is used, the filling door can no longer be closed and no more washing programs can be started. 0 1 0 Setting the Child Safety Feature: Use a coin to turn the rotary knob (on the inside of the filling door) clockwise as far as it will go. Warning! The rotary knob must not be pressed in following adjustment, otherwise the child safety feature is not active. The rotary knob must project as shown in the diagram.
Setting up and connection instructions Setting up and connection instructions Safety Instructions for Installation • Do not tilt the washing machine onto its front or onto its right side (looking from the front). Electrical components could get wet! • Check the washing machine for transport damage. Never connect a damaged unit. Consult your supplier in the event of damage.
Setting up and connection instructions Setting Up the Unit 3 Washing machines with curved panels are not suitable for substructures. Transporting the Unit • Do not place the washing machine on its front side or on its right side (looking from the front). Otherwise the electrical components can get wet. • Never transport the unit without using the transport safeguard. Do not remove the transport safeguard until you reach the installation site.
Setting up and connection instructions 2. Firmly pull both hose holders off the unit. 3 50 The special button E and the plug caps D (2 ea.) and G (1 ea.) are supplied with the unit. 3. Unscrew the two screws A using the special button E. 4. Unscrew the four screws B using the special button E. 5. Remove the transport rail C. 6. Screw the four screws B back in. 7. Close off the two large holes with the plug caps D.
Setting up and connection instructions Prepare the Installation Location • The installation surface must be clean, dry and free of floor wax residue and other lubricating coatings so that the unit does not slide away. Do not use any lubricants as sliding aids. • It is not recommended to set up the washing machine on deep-pile carpets or on floor coverings with soft foam underlays, as this would mean that the stability of the unit would not be guaranteed.
Setting up and connection instructions Compensate for Floor Unevenness Automatic Adjustment Foot: Your washing machine's rear left foot is of a spring leg design. This guarantees good stability of the unit, even at high spinning speeds. If the washing machine still does not stand firmly enough during spinning, proceed as follows: 0 1. Adjust the three adjustment feet to the setpoint 10mm. To do this, use the supplied special button to remove the transport safeguard.
Setting up and connection instructions Electrical Connection Refer to the rating plate for details of the mains voltage, current type and the necessary fuses. The rating plate is located at the top behind the filling door.
Setting up and connection instructions Water Inflow A pressure hose 1.5m in length is supplied. If a longer inflow hose is required, only a VDE-approved, complete set of hoses with fitted hose screw connections offered by our Customer Service is permissible. – Sets of hoses in lengths of 2.2m, 3.5m and 5m are available for washing machines without Aqua-Control. – Sets of hoses in lengths of 2.0m, 2.9m and 3.9m are available for washing machines with Aqua-Control.
Setting up and connection instructions Water Drainage The drainage hose can either be connected to a siphon or hung in a wash basin or bath tub. Only original hoses may be used for extension purposes (max. 3m on the floor and then up to 80cm high). The Customer Service stocks hoses in lengths of 2.7 and 4m. Attention! It is absolutely essential to install the drainage hose free of pinches. 0 Water Drainage into a Siphon The grommet on the end of the hose fits all commonly used siphon types.
Setting up and connection instructions Delivery Heads over 1m To pump off the washing / rinsing agent, every washing machine has a pump which transports liquids via the drainage hose up to a height of 1m, calculated from the machine's floor. For delivery heads over 1m, consult the Customer Service. Technical Data Height adjustment Filling quantity (program-dependent) Use Drum speed, spin Water pressure Dimensions (Measurements in mm) 56 Approx. +10/-5mm max.
Customer Services Customer Services Schweiz - Suisse - Svizzera A + T Hausgeräte AG Kundendienst AEG Industriestraße 10 5506 Mägenwil Service Eine Tel.-Nr. für die ganze Schweiz ServicePhon 0848 848 348 Fax 062/889 95 85 Ersatzteildienst Ersatzteilverkauf ganze Schweiz Telefon 0848 848 028 Fax 062/889 94 90 Regionalbüro Westschweiz: 1028 Préverenges Le Trési 6, Verkauf Tel. 021/803 24 15 Fax 021/803 25 24 Regionalbüro Tessin: 6616 Losone Centro Montana Verkauf Tel.
Index Index A Aborting the programme . . . . . . . . . . . . . . Additional programme - buttons . . . .12, Aqua Control . . . . . . . . . . . . . . . . . 15, 28, Automatic adjustment foot . . . . . . . . . . 9, Multidisplay . . . . . . . . . . . . . . . . . . . . . . . . .59 26 29 36 52 C Care agent . . . . . . . . . . . . . . . . . . . . 9, 18, Child safety feature . . . . . . . . . . . . . . .35, Conditioner . . . . . . . . . . . . . . . . 9, 11, 19, Correcting the programme . . . . . . . . . . . .
Service Service In the section ”What to do if ...” there is a list of some faults which you can remedy yourself. Look there first if a fault occurs. If you find no information there, please consult your Customer Service Centre. Always prepare in advance for the discussion. By doing so you will simplify the diagnosis and the decision on whether customer service is necessary. Note the PNC-number and the S-number. Both can be found on the rating plate on the inside of the door on your washing machine. PNC ...
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.
