LAVAMAT BELLA 3251 Waschautomat Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf. Geben Sie diese Benutzerinformation an eventuelle Nachbesitzer des Gerätes weiter. 1 3 2 2 Folgende Symbole werden im Text verwendet: Sicherheitshinweise Warnung! Hinweise, die Ihrer persönlichen Sicherheit dienen. Achtung! Hinweise, die zur Vermeidung von Schäden am Gerät dienen.
Inhalt Gebrauchsanweisung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Sicherheit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Gerätebeschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Bedienblende . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Programmübersicht . . . . . . . . . . . . . . . . . . . . .
Aufstell- und Anschlussanweisung . . . . . . . . . . . . . . . . . . . . . . . 26 Sicherheitshinweise für die Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Aufstellung des Gerätes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gerät transportieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transportsicherung entfernen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gebrauchsanweisung 1 Sicherheit Vor der ersten Inbetriebnahme • Beachten Sie die „Aufstell- und Anschlussanweisung“. • Bei Geräteanlieferung in Wintermonaten mit Minustemperaturen: Waschautomat vor Inbetriebnahme für 24 Stunden bei Raumtemperatur lagern. Bestimmungsgemäße Verwendung • Der Waschautomat ist nur zum Waschen haushaltsüblicher Wäsche im Haushalt bestimmt. • Umbauten oder Veränderungen am Waschautomaten sind nicht zulässig.
Allgemeine Sicherheit • Reparaturen am Waschautomaten dürfen nur von Fachkräften durchgeführt werden. • Den Waschautomaten niemals in Betrieb nehmen, wenn das Netzkabel beschädigt ist oder Bedienblende, Arbeitsplatte oder Sockelbereich so beschädigt sind, dass das Geräteinnere offen zugänglich ist. • Vor Reinigung, Pflege und Wartungsarbeiten den Waschautomaten ausschalten. Zusätzlich Netzstecker aus der Steckdose ziehen oder – bei Festanschluss – LS-Schalter im Sicherungskasten ausschalten bzw.
Gerätebeschreibung Bedienblende Waschmittelschublade Typschild (hinter Einfülltür) Sockelklappe/ Laugenpumpe Schraubfüße (höhenverstellbar) Bedienblende Taste Schleudern/SPÜLSTOPP Multidisplay Taste ZEITVORWAHL Programmzusatz-Tasten Taste START/PAUSE Programmablauf-Anzeige Anzeige TÜR Programmwähler Anzeige ÜBERDOSIERT 7
Programmübersicht 6kg • PFLEGELEICHT 60, 50, 40, 30 3kg • LEICHTBÜGELN 40 1kg FEINWÄSCHE 40, 30 3kg WOLLE/SEIDE H (Handwäsche) 40, 30, KALT FEINSPÜLEN • • • • • • • • • •4) • • • • • • • • • • • • • • • • •4) • • • • • • • • • • • • • • • • • • • • 2kg • • • • 3kg • • • • • • • • • • KURZ SPÜLSTOPP 40-60 MIX 500 • 700 6kg 1000 KOCH-/BUNTWÄSCHE 95, 60, 40, 30 1200 • SENSITIV 6kg FLECKEN EXTRA SPÜLEN ENERGIESPAREN 2) Pro
Anwendung/Eigenschaften Energiesparprogramm bei 60 °C für leicht bis normal verschmutzte Koch-/Buntwäsche aus Baumwolle/Leinen. Programm für normal bis stark verschmutzte Koch-/Buntwäsche aus Baumwolle/ Leinen. Programm für Koch-/Buntwäsche, welche für unterschiedliche Waschtemperaturen gekennzeichnet ist. Teile, die laut Pflegekennzeichen üblicherweise bei 40 °C oder bei 60 °C getrennt gewaschen werden, können in diesem Programm zusammen gewaschen werden.
Vor dem ersten Waschen 1. Waschmittelschublade öffnen. 2. Etwa 1 Liter Wasser durch die Waschmittelschublade in den Waschautomaten gießen. Beim nächsten Programmstart wird dadurch der Laugenbehälter geschlossen und die ÖKO-Schleuse kann ordnungsgemäß funktionieren. 3. Um eventuelle fertigungsbedingte Rückstände aus Trommel und Laugenbehälter zu entfernen, den ersten Waschgang ohne Wäsche durchführen. Programm: KOCHWÄSCHE/BUNTWÄSCHE 60, Taste KURZ drücken, ca. 1/4 Messbecher Waschpulver zugeben.
Waschgang durchführen Einfülltür öffnen/Wäsche einfüllen 1. Einfülltür öffnen: am Griff der Einfülltür ziehen. Die Anzeigen TÜR und START/PAUSE zeigen bei eingeschaltetem Gerät an, ob die Einfülltür geöffnet werden kann: Anzeige TÜR Anzeige START/PAUSE Tür öffnen möglich? leuchtet grün blinkt rot oder ist aus ja leuchtet grün leuchtet rot ja, nach Drücken der Taste START/PAUSE leuchtet rot oder ist aus blinkt rot oder leuchtet rot nein, zu hoher Wasserstand bzw. zu hohe Temperatur 2.
1. Waschmittelschublade bis zum Anschlag herausziehen 2. Wasch-/Pflegemittel einfüllen. 3. Waschmittelschublade ganz hineinschieben. Waschpulver/Tabs für die Hauptwäsche Weichspüler/ Formspüler/ Stärke Fleckensalz/-tabs Waschpulver/Tabs für die Vorwäsche oder Wasserenthärter Waschpulver/Tabs für die Hauptwäsche Wenn Sie Wasserenthärter benutzen und das rechte Fach für Vorwaschmittel benötigen, den Wasserenthärter auf das Hauptwaschmittel in das linke Fach geben.
Schleuderdrehzahl ändern/Spülstopp wählen 3 Der Waschautomat schlägt die maximal zulässige Drehzahl vor, die für das gewählte Programm geeignet ist. Diese Drehzahl können Sie verringern: Dazu Taste Schleudern/SPÜLSTOPP so oft drücken, bis die gewünschte Anzeige leuchtet. Die Drehzahl für das Endschleudern kann während des Programms noch geändert werden. Dazu: 1. Taste START/PAUSE drücken. 2. Drehzahl ändern. 3. Taste START/PAUSE erneut drücken.
Programmzusätze wählen 3 Falls gewünscht, ProgrammzusatzTaste(n) drücken. Die zugehörige Anzeige leuchtet. Wenn „Err“ im Multidisplay blinkt, ist der gewählte Programmzusatz mit dem eingestellten Waschprogramm nicht kombinierbar. EXTRASPÜLEN Bei den Programmen ENERGIESPAREN, KOCH-/BUNTWÄSCHE, FEINWÄSCHE, PFLEGELEICHT und LEICHTBÜGELN werden zwei zusätzliche Spülgänge ausgeführt (z. B. bei Übersensibilität der Haut). KURZ Verkürztes Waschprogramm für leichter verschmutzte Wäsche.
Zeitvorwahl einstellen 3 3 Mit der Taste ZEITVORWAHL können Sie den Start eines Programms um 30 Minuten (30') bis max. 23 Stunden (23h) aufschieben. 1. Programm wählen. 2. Taste ZEITVORWAHL so oft drücken, bis der gewünschte Startaufschub im Multidisplay erscheint, z. B. 12h, wenn das Programm in 12 Stunden starten soll. Die Anzeige ZEITVORWAHL leuchtet. Wird 23h angezeigt und Sie drücken ein weiteres Mal, ist die Zeitvorwahl wieder aufgehoben.
Programm unterbrechen/Wäsche nachlegen Programm unterbrechen • Durch Drücken der Taste START/PAUSE kann ein Programm jederzeit unterbrochen und durch erneuten Tastendruck auf START/PAUSE wieder fortgesetzt werden. • Zum vorzeitigen Abbruch eines Programms den Programmwähler auf AUS drehen. Achtung! Wasser im Gerät beachten! Wäsche nachlegen Wäsche nachlegen ist möglich, solange die Anzeige TÜR grün leuchtet. 1. Taste START/PAUSE drücken. Einfülltür lässt sich öffnen. 2.
Kindersicherung Bei eingestellter Kindersicherung kann die Einfülltür nicht mehr geschlossen werden. Kindersicherung einstellen: Drehknopf (an der Innenseite der Einfülltür) mit einer Münze im Uhrzeigersinn bis zum Anschlag drehen. 1 Warnung! Der Drehknopf darf sich nach dem Einstellen nicht in versenkter Position befinden, sonst ist die Kindersicherung nicht aktiv! Der Drehknopf muss gemäß Abbildung herausstehen. Kindersicherung aufheben: Drehknopf entgegen dem Uhrzeigersinn bis zum Anschlag drehen.
Waschmittelschublade Die Waschmittelschublade sollte regelmäßig gereinigt werden. 1. Waschmittelschublade mit kräftigem Ruck entnehmen. 2. Weichspülereinsatz aus dem mittleren Fach herausnehmen. 3. Alle Teile mit Wasser reinigen. 4. Weichspülereinsatz bis zum Anschlag aufstecken, so dass er fest sitzt. 5. Gesamten Einspülbereich des Waschautomaten, besonders auch die Düsen an der Oberseite der Einspülkammer, mit einer Bürste reinigen. 6. Waschmittelschublade in Führungsschienen einsetzen und einschieben.
Was tun, wenn... Kleine Störungen selbst beheben Falls während des Betriebs einer der folgenden Fehlercodes im Multidisplay angezeigt wird: – E10 (Probleme mit Wasserzulauf), – E20 (Probleme mit Wasserablauf), – E40 (Einfülltür offen), sehen Sie bitte in nachfolgender Tabelle nach. Nachdem der Fehler behoben ist, Taste START/PAUSE drücken. Bei anderen Fehlern (E und Zahl oder Buchstabe): Gerät aus- und wieder einschalten. Programm neu einstellen. Taste START/PAUSE drücken.
Problem Waschautomat vibriert während des Betriebs oder steht unruhig. Wäsche ist nicht geschleudert. Mögliche Ursache Abhilfe Transportsicherung nicht entfernt. Transportsicherung entfernen. Schraubfüße nicht korrekt eingestellt. Füße laut Aufstell- und Anschlussanweisung justieren. Trommel immer möglichst Nur wenige, große Wäschevoll beladen. Große und kleistücke in der Trommel. ne Teile mischen. Verschraubung am Zulaufschlauch undicht. Zulaufschlauch festschrauben. Ablaufschlauch undicht.
Problem Mögliche Ursache Einfülltür verriegelt. Einfülltür lässt sich bei eingeschaltetem Gerät nicht öffnen. Wäsche stark verknittert. Abhilfe Warten, bis Anzeige TÜR grün leuchtet. Programm läuft weiter, wenn Stromausfall vorüber ist. Stromausfall! (Alle Anzeigen sind aus.) Einfülltür bleibt ca. 4 bis 10 Minuten verriegelt. Zum Wäsche entnehmen: Ist Wasser im Gerät zu sehen, vor Öffnen der Einfülltür erst das Wasser ablassen (siehe Abschnitt „Notentleerung durchführen“).
Notentleerung durchführen 1 Warnung! Waschautomat vor Notentleerung ausschalten und den Netzstecker aus der Steckdose ziehen! Warnung! Die Waschlauge, die aus dem Notentleerungsschlauch ausläuft, kann heiß sein. Verbrühungsgefahr! Vor einer Notentleerung Waschlauge abkühlen lassen! 1. Sockelklappe aufklappen und abziehen. 2. Notentleerungsschlauch herausnehmen. 3. Flaches Auffanggefäß unterstellen. Anschließend Verschlussstopfen durch Drehen gegen den Uhrzeigersinn lösen und herausziehen. 4.
Laugenpumpe 1 Die Laugenpumpe ist wartungsfrei. Das Öffnen des Pumpendeckels ist nur im Störungsfall erforderlich, wenn kein Wasser mehr abgepumpt wird, z. B. bei blockiertem Pumpenrad. Bitte vor dem Einfüllen der Wäsche immer sicherstellen, dass sich keine Fremdkörper in den Taschen oder zwischen der Wäsche befinden. Büroklammern, Nägel etc., die eventuell mit der Wäsche in den Waschautomaten gelangt sind, bleiben im Pumpengehäuse (Fremdkörperfalle, die das Pumpenrad schützt) liegen.
Entsorgung 2 2 3 1 24 Verpackungsmaterial Die Verpackungsmaterialien sind umweltverträglich und wiederverwertbar. Die Kunststoffteile sind gekennzeichnet, z. B. >PE<, >PS< etc. Entsorgen Sie die Verpackungsmaterialien entsprechend ihrer Kennzeichnung bei den kommunalen Entsorgungsstellen in den dafür vorgesehenen Sammelbehältern.
Technische Daten 5 Dieses Gerät entspricht den folgenden EG-Richtlinien: – 73/23/EWG vom 19.02.1973 Niederspannungs-Richtlinie – 89/336/EWG vom 03.05.1989 EMV-Richtlinie einschließlich Änderungs-Richtlinie 92/31/EWG – 93/68/EWG vom 22.07.1993 CE-Kennzeichnungs-Richtlinie Höhe x Breite x Tiefe 850 x 598 x 640mm Tiefe bei geöffneter Einfülltür 1017 mm Höhenverstellbarkeit ca. +10/-5mm Füllmenge (programmabhängig) max.
Aufstell- und Anschlussanweisung 1 Sicherheitshinweise für die Installation • Dieser Waschautomat ist nicht unterbaufähig. • Vor Inbetriebnahme das Gerät auf Transportschäden überprüfen. Ein beschädigtes Gerät auf keinen Fall anschließen. Wenden Sie sich im Schadensfall an Ihren Lieferanten. • Vor Inbetriebnahme müssen alle Teile der Transportsicherung entfernt sein. Andernfalls kann es beim Schleudern zu Schäden am Gerät oder an benachbarten Möbeln kommen.
Aufstellung des Gerätes Gerät transportieren 1 Warnung! Der Waschautomat hat ein hohes Gewicht. Verletzungsgefahr! Vorsicht beim Anheben. • Das Gerät nicht auf die Vorderfront und nicht auf die rechte Seite (von vorne gesehen) legen. Elektrische Bauteile können nass werden. • Gerät niemals ohne Transportsicherung transportieren. Transportsicherung erst am Aufstellort entfernen! Transport ohne Transportsicherung kann zu Schäden am Gerät führen.
Transportsicherung entfernen Achtung! Vor Inbetriebnahme unbedingt alle Teile der Transportsicherung entfernen! Transportsicherung für einen möglichen späteren Transport (Umzug) aufbewahren. 1. An der Geräterückseite beide Schlauchhalter öffnen und Schläuche sowie Netzkabel herausnehmen. 2. Beide Schlauchhalter mit kräftigem Ruck vom Gerät abziehen. 3. Beide Kunststoffkappen seitlich abziehen. 3 Spezialschlüssel A und Verschlusskappen B (2 Stück) und C (1 Stück) liegen dem Gerät bei. 4. Schraube D inkl.
7. Zwei Schrauben E mit Spezialschlüssel A herausschrauben. 8. Vier Schrauben F mit Spezialschlüssel A herausschrauben. 9. Transportschiene G abnehmen. 10. Die vier Schrauben F wieder einschrauben. 11. Die zwei großen Löcher mit Verschlusskappen B verschließen. Achtung! Alle Verschlusskappen B (2 Stück) und C (1 Stück) so kräftig eindrücken, dass sie in die Rückwand einrasten (Spritzwasserschutz!). Aufstellort Achtung! Das Gerät darf nicht in einem frostgefährdeten Raum betrieben werden. Frostschäden bzw.
Gerät ausrichten Die vier Füße des Gerätes sind voreingestellt. Grobe Unebenheiten können durch individuelles Einstellen der höhenverstellbaren Schraubfüße ausgeglichen werden. Dazu den beiliegenden Spezialschlüssel verwenden. Achtung! Unebenheiten des Bodens nicht durch Unterlegen von Holz, Pappe oder ähnlichem ausgleichen, sondern durch Einstellen der höhenverstellbaren Schraubfüße.
Wasserzulauf 3 Mitgeliefert wird ein Druckschlauch von 1,5m Länge. Wird ein längerer Zulaufschlauch benötigt, sind ausschließlich Originalschläuche zu verwenden. Der Kundendienst hält Schlauchsätze in verschiedenen Längen bereit. Dichtringe sind entweder in den Muttern der Schlauchverschraubung eingelegt oder im Beipack enthalten. Keine anderen Dichtungen verwenden! Achtung! Alle Schlauchverschraubungen nur von Hand anziehen. 1. Schlauch mit dem abgewinkelten Anschluss an der Maschine anschließen.
Wasserablauf Der Höhenunterschied zwischen Standfläche und Wasserabfluss darf höchstens 1 Meter betragen. Zur Verlängerung dürfen nur Originalschläuche verwendet werden. (Max. 3 m auf dem Fußboden verlegt und dann bis 80 cm hoch). Der Kundendienst führt Ablaufschläuche in verschiedenen Längen. Wasserablauf in einen Siphon Die Verbindungsstelle Tülle/Siphon mit einer Schlauchschelle (im Fachhandel erhältlich) sichern. 1 Wasserablauf in ein Waschbecken/Badewanne Achtung! – Kleine Becken sind nicht geeignet.
Kundendienststellen Servicestellen 5506 Mägenwil/Zürich Industriestrasse 10 9000 St.
Service Bei technischen Störungen prüfen Sie bitte zunächst, ob Sie mit Hilfe der Gebrauchsanweisung (Kapitel „Was tun, wenn...“) das Problem selbst beheben können. Wenn Sie das Problem nicht beheben konnten, wenden Sie sich bitte an den Kundendienst oder einen unserer Service-Partner. Um Ihnen schnell helfen zu können, benötigen wir folgende Angaben: – Modellbezeichnung – Produkt-Nummer (PNC) – Serien-Nummer (S-No.
From the Electrolux Group. The world´s No.1 choice. Die Electrolux-Gruppe ist der weltweit größte Hersteller von gas- und strombetriebenen Geräten für die Küche, zum Reinigen und für Forst und Garten. Jedes Jahr verkauft die Electrolux-Gruppe in über 150 Ländern der Erde über 55 Millionen Produkte (Kühlschränke, Herde, Waschmaschinen, Staubsauger, Motorsägen und Rasenmäher) mit einem Wert von rund 14 Mrd. USD. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg-electrolux.