Waschautomaten Automatic Washing Machines Lave-linge Lavatrici Wasautomaat Lavadoras Aufstell- und Anschlußanweisung für Waschautomaten mit gewölbter Blende Installation and connection instructions for automatic washing machines with vaulted front cover Installation et raccordements des lave-linge à bandeau bombé Instruzioni di installazione e collegamento per lavatrici con pannello rigonfiato Opstellings- en aansluitvoorschrift voor wasautomaten met gewelfd voorpaneel Instrucciones para la instalación y la
Contents Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Appliance Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Front and Side Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Appliance Installation . . . . . . . . . . . . . . . .
1 Important Safety Information The safety of AEG appliances is in accordance with recognised technological standards and appliance safety legislation. We nevertheless feel that it is important to acquaint you with the following safety guidelines. • This appliance is heavy, care should be taken when moving it. • When moving, do not tip the washing machine onto it’s front or left hand side (viewed from the front). This is to prevent the possibility of electrical components becoming wet.
Appliance Dimensions Front and Side Views 950 592 100 10 -5 +10 850 -5 +10 598 50 575 Rear View Appliances with cold water connection only 16
Appliances with hot and cold water connections Hot water inlet Cold water inlet Appliance Installation 3 The appliance worktop must not be removed to gain a height reduction when installing under a kitchen worktop. Appliance Transit • To prevent electrical components becoming wet when moving the appliance, do not tip the washing machine onto it’s front or the left hand side (viewed from the front). • Do not transport the appliance without the transit packaging/bolts/ bar in place.
Appliance Installation Removing Transit Packaging • Ensure all transit packaging is removed prior to installation. • Retain transit packaging for future use. F G E A C C B B D H 3 0 0 0 0 0 0 0 18 The appliance is supplied with a spanner (H) and plastic caps (E) (2 pcs.) and (G) (1 pc). Remove the hose holder (A). Remove the 2 screws (B) with the spanner supplied (H). Remove the 4 screws (C). Remove the transit bar (D). Cover the holes left by screws (B) the 2 plastic caps (E).
Appliance Installation Installation-Site Preparation • The installation surface must be clean, dry and level. • Do not install on deep pile carpet. • If the appliance ist installed next to heat source (e. g. cooking appliance), a heat insulating pad (85 x 57 cm) must be placed between the washing machine and the heat source. • Do not install the appliance in locations where the temperature may fall below freezing.
Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. 1 WARNING - THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. The rating plate is located at the top of the rim of the open door.
Electrical Connection • The wire coloured green and yellow must be connected to the terminal marked with the letter “E“ or by the earth symbol or coloured green and yellow. • The wire coloured blue must be connected to the terminal “N“ or coloured black. • The wire coloured brown must be connected to the terminal marked “L“ or coloured red. • Upon completion there must be not cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath.
Water Connection 3 The washing machine is provided with safety devices preventing backcontamination of the water supply and complies with local water authority requirements. This appliance is designed to be permanently plumbed into your home’s water supply. Before connecting up the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes.
0 Connect the hose to the machine with the right angled connector. IMPORTANT: Do not overtighten the plastic nuts on the threaded connectors. Rubber Washer 0 Connect the hose end with a straight connector to the water supply tap with an 3/4" thread. Rubber Washer IMPORTANT: Do not overtighten the plastic nuts on the inlet hose threaded connectors. Fine Filter WARNING: Open the water taps slowly and check the connections are watertight before final positioning of the machine.
Water Connection Appliances with hot and cold water fill Washing machines with hot and cold fill should be connected as shown below. hot cold hot WARNING: The incoming hot water temperature must not exceed 70°C. If only a cold water supply is available, connect the two hoses to the cold water outlet by means of a “Y“ connection piece. (A “Y“ piece is available from your AEG Service Force Centre, part number 645430709).
Water Connection Water Drainage The upright standpipe should have a minimum, length of 30 cm (12’’) from the bottom of the elbow to the top of the pipe (see diagram). Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water. Longer drain hoses are available in lengths of 2.7 and 4 metres from your AEG Service Force Centre.
AEG Service Force If you wish to contact your local AEG Service Force Centre for advice or spare parts, telephone: 0990 234234 26
