LB3681 USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................4 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 10 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com • • • • • • • • • Überschreiten Sie nicht die maximale Beladungsmenge von 8 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • Halten Sie sich an die mitgelieferte Montageanleitung. • Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist. • Der Boden, auf dem das Gerät aufgestellt werden soll, muss eben, stabil, hitzebeständig und sauber sein. • Stellen Sie sicher, dass die Luft zwischen dem Gerät und dem Boden zirkulieren kann.
www.aeg.com • Verwenden Sie ausschließlich Originalersatzteile. 2.6 Entsorgung WARNUNG! Verletzungs- und Erstickungsgefahr. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in der Trommel einschließen. • Entsorgen Sie das Gerät nach den lokalen Vorschriften zur Rücknahme und Entsorgung von Elektroaltgeräten (WEEE). • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung. • Schneiden Sie das Netzkabel in der Nähe des Geräts ab, und entsorgen Sie es. 3.
DEUTSCH 7 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 10. Lösen Sie die drei Schrauben mit dem mitgelieferten Schraubenschlüssel. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 1 2 8. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. Aus dem Ablaufschlauch könnte Wasser austreten.
www.aeg.com Stellen Sie sicher, dass die Luftzirkulation unter dem Gerät nicht durch Teppiche beeinträchtigt wird. Vergewissern Sie sich, dass das Gerät weder die Wand noch andere Geräte berührt. 2. Schrauben Sie die Füße zum Ausrichten des Geräts weiter heraus oder hinein. 3.3 Wasserzulaufschlauch 1. Schließen Sie den Wasserzulaufschlauch an der Rückseite der Maschine an. 2. Drehen Sie ihn nach links oder rechts, je nach Position des Wasserhahns.
DEUTSCH Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist. Wenden Sie sich an den Kundendienst, um einen anderen Zulaufschlauch zu erhalten. 9 Stellen Sie sicher, dass die Kunststoffführung beim Abpumpen nicht herausrutschen kann. 3.4 Aquastop-Vorrichtung Der Zulaufschlauch verfügt über eine Aquastop-Vorrichtung. Diese Vorrichtung verhindert Wasserlecks am Schlauch, die durch natürliche Alterung auftreten können. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an.
www.aeg.com Stellen Sie sicher, dass der Ablaufschlauch einen Bogen beschreibt, damit keine Partikel aus dem Becken in das Gerät gelangen können. 6. Stecken Sie den Schlauch direkt in ein Abflussrohr in der Zimmerwand und befestigen Sie ihn mit einer Schlauchschelle. 5. Ohne Kunststoffschlauchführung: Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Orientieren Sie sich an der Abbildung. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
DEUTSCH 11 4.2 Geräteübersicht 1 2 9 8 3 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Arbeitsplatte Waschmittelschublade Bedienfeld Türgriff Typenschild Filter der Ablaufpumpe Füße für die Ausrichtung des Geräts 8 9 10 11 12 Ablaufschlauch Anschluss des Zulaufschlauchs Netzkabel Transportschrauben Schlauchhalter 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 P r o g ra m m e Eco Baumwolle Pflegeleicht Fe i n w ä s c h e Wolle/S eide Dampf Anti-Allergie 2 0 m i n .
www.aeg.
DEUTSCH 13 Die Digitalanzeige zeigt Folgendes an: ). • Programmdauer (z.B. • Zeitvorwahl (z.B. oder ). • Programmende ( ). • Fehlercode (z. B. ). Kontrolllampe Hauptspülgang. Blinkt während der Vorwasch- und Hauptwaschphase. Kontrolllampe Spülphase. Blinkt während der Spülphase. Wenn die Option Soft Plus eingeschaltet ist, erscheint die Anzeige . Schleuder- und Abpumpphasenanzeige. Blinkt während der Schleuderund Abpumpphase. Dampfphasenanzeige. Knitterschutzphasenanzeige. Kindersicherungsanzeige.
www.aeg.com 6. DREHSCHALTER UND TASTEN 6.1 Ein/Aus Halten Sie diese Taste einige Sekunden lang gedrückt, um das Gerät ein- oder auszuschalten. Beim Ein- und Ausschalten ertönen zwei verschiedene Melodien. Da die Standby-Funktion das Gerät automatisch ausschaltet, um in einigen Fällen den Stromverbrauch zu verringern, müssen Sie es möglicherweise erneut einschalten. Siehe Abschnitt Standby im Kapitel „Täglicher Gebrauch“. 6.
DEUTSCH Wenn Sie die Taste Start/Pause berühren, wird lediglich die Abpumpphase ausgeführt. Das Gerät pumpt das Wasser nach etwa 18 Stunden automatisch ab. • Die Option Nur Abpumpen (überspringt die Wasch-, Spül- und Schleuderphasen). Das Gerät führt nur den Abpumpgang des gewählten Programms aus. Das Display zeigt Anzeige (kalt), die (kein Schleudern) und an. die Anzeige • Die Option Nur Schleudern (überspringt die Wasch- und Spülphasen).
www.aeg.com Nach Berührung der Taste Start/Pause zeigt das Display die Anzeige und die gewählte Zeitvorwahl an und das Gerät startet den Countdown. Auf dem Display erscheint die Anzeige . Diese Option kann auch zur Verkürzung des DampfProgramms verwendet werden. 6.8 Spülgang Mit dieser Taste können Sie eine der folgenden Optionen einstellen: • Option Extra Spülen Diese Option fügt dem gewählten Waschprogramm einige zusätzliche Spülgänge hinzu.
DEUTSCH 17 Programm Programmbeschreibung Baumwolle Baumwolle Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte. Das Programm Baumwolle bei 60 °C und das Programm Baumwolle bei 40 °C mit der Option sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“.
www.aeg.com Programm Programmbeschreibung 20 Min.-3 kg 20 min. - 3 kg Teile aus Baumwolle oder Synthetik, die leicht verschmutzt sind oder nur einmal getragen wurden. Outdoor Outdoor Pflegeleichte Sportbekleidung. Dieses Programm eignet sich zur schonenden Wäsche moderner Sportbekleidung, wie Trainings-, Radfahr- oder Joggingkleidung und ähnlicher OutdoorBekleidung. Die empfohlene Beladung beträgt 2.5 kg.
DEUTSCH 19 Programm Programmbeschreibung Maschinenreinigung Maschinenreinigung Wartungszyklus mit Heißwasser zur Reinigung und Auffrischung der Trommel und zum Entfernen von Rückständen, die Gerüche absondern können. Schalten Sie dieses Programm einmal im Monat ein, um beste Ergebnisse zu erzielen. Nehmen Sie alle Gegenstände aus der Trommel, bevor Sie das Programm einschalten. Drehen Sie in der Waschmittelschublade die Klappe im Fach für den Hauptwaschgang nach oben.
www.aeg.com Programm Standardtemperatur Temperaturbereich Maximale Schleuderdrehzahl Schleuderdrehzahlbereich 20 Min.-3 kg 30 °C 40 °C - 30 °C 1200 U/min 1200 U/min – 400 U/min Outdoor 30 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min 40 °C 60 °C – kalt 1200 U/min 1200 U/min – 400 U/min 8 kg 60 °C 1200 U/min 1200 U/min – 400 U/min - Jeans Maschinenreinigung Maximale Beladung 3 kg 2.5 kg1) 1 kg2) 1) Waschprogramm. 2) Waschprogramm und Imprägnierphase.
Zeit Sparen 3) ■ ■ ■ Startzeitvorwahl ■ ■ ■ Plus Dampf ■ ■ ■ ■ ■ Soft Plus ■ ■ ■ ■ ■ Jeans ■ Outdoor ■ 2) 21 Maschinenreinigung 20 Min.-3 kg Anti-Allergie Feinwäsche ■ Optionen Dampf Pflegeleicht Wolle/Seide Baumwolle Programm DEUTSCH ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C. 2) Diese Option ist nicht verfügbar bei einer Temperatur unter 30 °C.
www.aeg.com Ausnahme der Taste Ein/Aus) sind ausgeschaltet. • Bevor Sie die Taste Start/Pause berühren: Das Gerät kann nicht starten. Das Gerät speichert die Auswahl dieser Option, wenn Sie es ausschalten. 8.
DEUTSCH 23 10. TÄGLICHER GEBRAUCH WARNUNG! Siehe Kapitel "Sicherheitshinweise". 10.1 Einschalten des Geräts 1. Stecken Sie den Netzstecker in die Netzsteckdose. 2. Öffnen Sie den Wasserhahn. 3. Halten Sie die Taste Ein/Aus einige Sekunden lang gedrückt, um das Gerät einzuschalten. Es ertönt eine kurze Melodie (falls eingeschaltet). Der Programmwahlschalter wird automatisch auf Baumwolle gesetzt. VORSICHT! Vergewissern Sie sich, dass keine Wäschestücke zwischen Dichtung und Tür eingeklemmt sind.
www.aeg.com Entfernen Sie nach dem Waschgang bei Bedarf Waschmittelreste aus der Waschmittelschublade. 10.4 Überprüfen Sie die Position der Klappe 1. Ziehen Sie die Waschmittelschublade bis zum Anschlag heraus. 2. Drücken Sie den Hebel nach unten und ziehen Sie die Schublade heraus. 1 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz.
DEUTSCH gewünschte Waschprogramm. Die entsprechende Programmanzeige leuchtet auf. Die Kontrolllampe der Taste Start/Pause blinkt. Das Display zeigt die maximal zulässige Füllmenge für das Programm, die Standardtemperatur, die maximale Schleuderdrehzahl, die Programmphasen (falls verfügbar) und die voraussichtliche Programmdauer an. 2. Berühren Sie die entsprechenden Tasten, um die Temperatur und/oder Schleuderdrehzahl zu ändern. 3.
www.aeg.com 1. Das Gerät erkennt die Ladung innerhalb von 30 Sekunden: Die Z. B. die Wasch- oder Vorwaschphase und der ZeitAnzeige Doppelpunkt blinken, die Trommel dreht sich kurz. 2. Am Ende der Beladungskennung wird ausgeführt: erlischt die Anzeige und der ZeitDoppelpunkt hört auf zu blinken. Die Programmdauer wird entsprechend angepasst und kann sich verlängern oder verkürzen. Nach weiteren 30 Sekunden beginnt das Wasser einzulaufen.
DEUTSCH Wurde die ProSense-Phase bereits beendet und läuft Wasser in das Gerät ein, startet das neue Programm ohne die ProSense-Phase zu wiederholen. Um Wasser und Waschmittel nicht zu verschwenden, wird das Wasser nicht abgepumpt. Das Display zeigt die maximale Programmdauer an, die etwa 20 Minuten nach dem Start des neuen Programms aktualisiert wird. 10.
www.aeg.com Die Optionsanzeige oder erlischt, während die Anzeige blinkt und dann erlischt. 3. Wenn das Programm beendet ist und die Türverriegelungsanzeige erlischt, können Sie die Tür öffnen. 4. Halten Sie die Taste Ein/Aus einige Sekunden lang gedrückt, um das Gerät auszuschalten. In jedem Fall pumpt das Gerät das Wasser nach etwa 18 Stunden automatisch ab. 10.
DEUTSCH 11.2 Hartnäckige Flecken Für manche Flecken sind Wasser und Waschmittel nicht ausreichend. Wir empfehlen, diese Flecken vorzubehandeln, bevor Sie die entsprechenden Textilien in das Gerät geben. Spezial-Fleckentferner sind im Handel erhältlich. Verwenden Sie einen SpezialFleckentferner, der für den jeweiligen Flecken- und Gewebetyp geeignet ist. 11.
www.aeg.com 12.2 Entkalkung Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Entkalkers für Waschmaschinen. Prüfen Sie die Trommel regelmäßig auf Kalkablagerungen. Herkömmliche Waschmittel enthalten Wasserenthärtungsmittel, wir empfehlen dennoch gelegentlich ein Programm mit leerer Trommel und einem Entkalker durchzuführen. Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts. 12.
DEUTSCH zu beseitigen. Setzen Sie nach der Reinigung das Oberteil wieder ein. 31 12.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. 3. Stellen Sie sicher, dass alle Waschmittelreste an der Ober- und Unterseite der Aufnahme entfernt wurden. Reinigen Sie die Schubladenaufnahme mit einer kleinen Bürste.
www.aeg.com 2 1 1 2 4. Lassen Sie das Wasser ablaufen. 1 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, dass sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst. 5. Wenn der Behälter voll ist, schließen Sie den Ablaufkanal und leeren Sie den Behälter. 6. Wiederholen Sie die Schritte 4 und 5, bis kein Wasser mehr herausfließt. 2 10. Reinigen Sie das Sieb unter fließendem Wasser. 1 7.
DEUTSCH 33 1 2 1 2 3 2. Lockern Sie die Ringmutter, um den Zulaufschlauch vom Gerät zu entfernen. 12. Schließen Sie die Pumpenabdeckung. 2 1 Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: a. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. b. Starten Sie das Programm zum Abpumpen des Wassers. 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 12.
www.aeg.com 0 °C erreichen oder unter 0 °C sinken kann, entfernen Sie das im Zulaufschlauch und in der Ablaufpumpe verbliebene Wasser. 45° 20° 12.9 Notentleerung Kann das Gerät das Wasser nicht abpumpen, führen Sie den unter „Reinigen des Ablauffilters“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. 1. Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Schließen Sie den Wasserhahn. 3.
DEUTSCH Ist das Gerät überladen, nehmen Sie einige Wäschestücke aus der Trommel und/oder drücken Sie die Tür zu und berühren Sie gleichzeitig die Taste Start/Pause, bis die Anzeige aufhört zu blinken (siehe Abbildung unten). 35 • - Die Stromzufuhr ist nicht konstant. Warten Sie, bis die Netzspannung wieder konstant ist. • - Keine Kommunikation zwischen den elektronischen Bauteilen des Geräts. Schalten Sie das Gerät aus und wieder ein. • – Das Aqua-Control-System ist eingeschaltet.
www.aeg.com Störung Mögliche Abhilfe Überzeugen Sie sich, dass das Sieb des Zulaufschlauchs und das Sieb des Ventils nicht verstopft sind. Siehe „Reinigung und Pflege“. Vergewissern Sie sich, dass der Wasserzulaufschlauch nicht geknickt, beschädigt oder gekrümmt ist. Vergewissern Sie sich, dass der Wasserzulaufschlauch ordnungsgemäß angebracht ist. Das Wasser, das in das Vergewissern Sie sich, dass sich der Ablaufschlauch in der richGerät einläuft, wird sofort tigen Höhe befindet.
DEUTSCH Störung 37 Mögliche Abhilfe Vergewissern Sie sich, dass das Waschprogramm beendet ist. Stellen Sie das Abpump- oder Schleuderprogramm ein, wenn sich noch Wasser in der Trommel befindet. Stellen Sie sicher, dass das Gerät mit Spannung versorgt wird. Das Problem kann durch eine Gerätestörung verursacht worden sein. Wenden Sie sich an den autorisierten Kundendienst. Wenn Sie die Tür öffnen müssen, lesen Sie sorgfältig „Öffnen der Tür im Notfall“.
www.aeg.com Schalten Sie das Gerät nach der Überprüfung wieder ein. Das Programm wird an der Stelle fortgesetzt, an der es unterbrochen wurde. Tritt das Problem erneut auf, wenden Sie sich an den autorisierten Kundendienst. Wenn im Display andere Alarmcodes angezeigt werden. Schalten Sie das Gerät aus und wieder ein. Tritt das Problem weiterhin auf, wenden Sie sich an den autorisierten Kundendienst. 13.
DEUTSCH Während des Waschprogramms können durch die ProSense-Technologie die Programmdauer und die Verbrauchswerte variieren. Siehe „ProSense-Beladungserkennung“ im Kapitel „Täglicher Gebrauch“. Programme Beladung (kg) EnergieWasserUngefähverbrauch verbrauch re Pro(kWh) (Liter) grammdauer (in Minuten) Restfeuchte (%)1) Baumwolle60°C 8 1.65 80 200 44 Baumwolle40°C 8 1.25 80 200 44 Pflegeleicht40°C 3.5 0.78 55 130 35 Feinwäsche40°C 3.5 0.60 63 91 35 Wolle/Seide30°C 1.5 0.
www.aeg.com Die Schutzverkleidung gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt.
DEUTSCH 41 mitgelieferten Broschüre aufgeführten Geräten verwendet werden. So steht Ihr Gerät höher und die Be- und Entladung wird einfacher. Lesen Sie die dem Gerät und dem Zubehör beiliegenden Anleitungen sorgfältig durch. Die Schublade kann zur Aufbewahrung von Wäsche benutzt werden, z. B. für Handtücher, Reinigungsprodukte usw. Lesen Sie die mit dem Zubehör gelieferte Gebrauchsanleitung sorgfältig durch. WARNUNG! Stellen Sie den Wäschetrockner nicht unter die Waschmaschine. 16.
www.aeg.com Garantie Für jedes Produkt gewähren wir ab Verkauf bzw. Lieferdatum an den Endverbraucher eine Garantie von 2 Jahren. (Ausweis durch Garantieschein, Faktura oder Verkaufsbeleg). Die Garantieleistung umfasst die Kosten für Material, Arbeits- und Reisezeit.
DEUTSCH 43
157006131-A-462016 www.aeg.