LB3681 USER MANUAL FR Notice d'utilisation Lave-linge
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ.............................................................................. 3 2. CONSIGNES DE SÉCURITÉ..................................................................................... 4 3. INSTALLATION......................................................................................................... 6 4. DESCRIPTION DE L'APPAREIL.............................................................................. 10 5. BANDEAU DE COMMANDE..
FRANÇAIS 1. 3 INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • Les orifices d'aération situés à la base (si présents) ne doivent pas être obstrués par de la moquette, un tapis, ou tout type de revêtement de sol. L'appareil doit être raccordé à l'arrivée d'eau à l'aide des tuyaux neufs fournis, ou d'autres tuyaux neufs fournis par le service après-vente agréé. N'utilisez pas de tuyaux provenant d'anciens appareils.
FRANÇAIS • Utilisez toujours une prise de courant de sécurité correctement installée. • Vérifiez que les données électriques figurant sur la plaque signalétique correspondent à celles de votre réseau. Si ce n'est pas le cas, contactez un électricien. • N'utilisez pas d'adaptateurs multiprises ni de rallonges. • Veillez à ne pas endommager la fiche secteur ni le câble d'alimentation. Le remplacement du cordon d'alimentation de l'appareil doit être effectué par notre service après-vente agréé.
www.aeg.com 3. INSTALLATION AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 3.1 Déballage AVERTISSEMENT! Retirez l'intégralité de l'emballage et les boulons de transport avant d'installer l'appareil. AVERTISSEMENT! Servez-vous de gants. 4. Ouvrez le hublot et retirez la cale en polystyrène du joint du hublot, ainsi que tous les articles présents dans le tambour. 1. Retirez le film externe. Si nécessaire, utilisez un cutter. 2.
FRANÇAIS 7 1 2 8. Remettez l'appareil en position verticale. 9. Retirez le câble d'alimentation électrique et le tuyau de vidange de leurs supports. Il est possible de voir de l'eau s'écouler du tuyau d'évacuation. Cette eau provient des tests effectués sur l'appareil en usine. 11. Retirez les entretoises en plastique. 12. Placez les caches en plastique, fournis dans le sachet du manuel d'utilisation, dans les trous.
www.aeg.com 45 20 O O x4 L'appareil doit être de niveau et stable. Une mise de niveau correcte évite les vibrations, le bruit ou des déplacements de l'appareil au cours de son fonctionnement. Assurez-vous que le tuyau d'arrivée d'eau n'est pas en position verticale. 3. Si nécessaire, desserrez la bague de serrage pour bien le positionner. 4. Raccordez le tuyau d'arrivée d'eau à un robinet d'eau froide fileté (3/4 pouce). 3.3 Tuyau d'arrivée d'eau 1.
FRANÇAIS La partie rouge dans la fenêtre « A » témoigne de ce dysfonctionnement. 9 Vérifiez que l'extrémité du tuyau de vidange n'est pas plongée dans l'eau. Il pourrait y avoir un reflux d'eau sale dans l'appareil. 3. À une conduite fixe dotée d'une ventilation spéciale : insérez directement le tuyau dans la conduite d'évacuation. Reportezvous à l'illustration. A Dans ce cas, fermez le robinet d'arrivée d'eau et contactez le service après-vente agréé pour faire remplacer le tuyau. 3.
www.aeg.com Veillez à ce que le tuyau de vidange fasse une boucle afin d'éviter que des particules passent de l'évier à l'appareil. 6. Placez le tuyau directement dans une conduite de vidange murale intégrée et serrez-le avec une attache. La longueur maximale du tuyau de vidange est de 400 cm. Contactez le service après-vente agréé pour obtenir d'autres longueurs de tuyaux de vidange et des rallonges. 4. DESCRIPTION DE L'APPAREIL 4.
FRANÇAIS 11 4.2 Vue d'ensemble de l'appareil 1 2 3 9 8 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Plan de travail Distributeur de produit de lavage Bandeau de commande Poignée d'ouverture du hublot Plaque signalétique Filtre de la pompe de vidange Pieds pour la mise de niveau de l'appareil 8 9 10 11 12 Tuyau de vidange Raccord du tuyau d'arrivée d'eau Câble d'alimentation électrique Boulons de transport Support du tuyau 5. BANDEAU DE COMMANDE 5.
www.aeg.
FRANÇAIS 13 L'indicateur numérique peut afficher : ). • La durée du programme (par ex. • Le départ différé (par ex. ou ). • La fin du cycle ( ). • Un code d'alarme (par ex. ). Voyant de phase de lavage. Il clignote au cours des phases de prélavage et de lavage. Voyant de phase de rinçage. Il clignote durant la phase de rinçage. Lorsque l'option Soft Plus est activée, l'indicateur apparaît. Voyant des phases d'essorage et de vidange. il clignote au cours des phases d'essorage et de vidange.
www.aeg.com 6. SÉLECTEUR ET TOUCHES 6.1 Marche/Arrêt Appuyez sur cette touche pendant quelques secondes pour allumer et éteindre l'appareil. Deux différents signaux sonores retentissent lorsque vous allumez ou éteignez l'appareil. La fonction Veille éteint automatiquement l'appareil pour réduire la consommation d'énergie. Par conséquent, dans certains cas, il se peut que vous deviez le rallumer. Pour plus de détails, reportez-vous au paragraphe « Veille » du chapitre « Utilisation quotidienne ». 6.
FRANÇAIS L'appareil effectue uniquement la phase de vidange du programme de lavage sélectionné. L'indicateur (froid), l'indicateur (sans essorage) et l'indicateur apparaissent. • Option Essorage uniquement (annulation des phases de lavage et de rinçage). L'appareil effectue uniquement la phase d'essorage du programme de lavage sélectionné. L'indicateur de phase s'affichent.
www.aeg.com Cette option permet d'ajouter quelques rinçages en fonction du programme de lavage sélectionné. Utilisez cette option pour les personnes allergiques aux résidus de produits de lavage et dans les régions où l'eau est douce. Cette option rallonge légèrement la durée du programme. • Annuler la phase de lavage - option Rinçage uniquement L'appareil effectue uniquement les phases de rinçage, d'essorage et de vidange du programme sélectionné.
FRANÇAIS Programme Description des programmes Blanc/Couleurs Baumwolle Coton blanc et couleurs. Normalement sale ou légèrement sale. Programmes standard pour les valeurs de consommation de l'étiquette énergétique.Conformément à la norme 1061/2010, le programme « Baumwolle à 60 °C et le pro- 17 gramme « Baumwolle à 40 °C avec l'option sont respectivement le « programme standard à 60 °C pour le coton » et le « programme standard à 40 °C pour le coton ».
www.aeg.com Programme Description des programmes Anti-Allergies Anti-Allergie Articles en coton blanc. Ce programme élimine les micro-organismes grâce à une phase de lavage à une température maintenue à plus de 60 °C pendant quelques minutes. Cela permet d'éliminer les germes, bactéries, micro-organismes et particules. Pour garantir une parfaite élimination des résidus de détergent et des particules de pollen ou autres allergènes sur les textiles, effectuez une phase de rinçage supplémentaire.
FRANÇAIS 19 Programme Description des programmes Nettoyage tambour Maschinenreinigung Le cycle de maintenance à l'eau chaude sert à nettoyer et rafraîchir le tambour, ainsi qu'à éliminer les résidus qui pourraient entraîner la formation de mauvaises odeurs. Pour des résultats optimaux, effectuez ce cycle une fois par mois. Avant d'effectuer ce cycle, retirez tous les articles du tambour.
www.aeg.com Programme Température par défaut Plage de températures Vitesse d'essorage maxi- Charge maximale male Plage de vitesses d'essorage 20 min.-3 kg 30 °C 40 °C - 30 °C 1200 tr/min 1200 tr/min - 400 tr/min Outdoor 30 °C 40 °C - Froid 1200 tr/min 1200 tr/min - 400 tr/min 40 °C 60 °C - Froid 1200 tr/min 1200 tr/min - 400 tr/min 8 kg 60 °C 1200 tr/min 1200 tr/min - 400 tr/min - Jeans Nettoyage tambour 3 kg 2.5 kg1) 1 kg2) 1) Programme de lavage.
■ ■ Gain de temps 3) ■ ■ ■ Départ différé ■ ■ ■ Vapeur Plus ■ ■ ■ ■ ■ Soft Plus ■ ■ ■ ■ ■ ■ ■ ■ ■ 21 Nettoyage tambour ■ 2) Jeans ■ Outdoor Laine/Soie ■ 20 min.-3 kg Délicats ■ Rinçage uniquement Anti-Allergies Synthétiques ■ Options Vapeur Blanc/Couleurs Programme FRANÇAIS ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) Cette option n'est pas disponible avec des températures de lavage inférieures à 40 °C.
www.aeg.com Vous pouvez activer cette option : 8.3 Rinçage plus permanent • Après avoir appuyé sur la touche Départ/Pause : toutes les touches et le sélecteur de programme sont désactivés (à l'exception de la touche Marche/Arrêt). • Avant d'appuyer sur la touche Départ/Pause : l'appareil ne peut pas démarrer. Après avoir éteint l'appareil, cette option reste sélectionnée. Cette fonction vous permet de maintenir la fonction Rinçage Plus en permanence lorsque vous sélectionnez un nouveau programme.
FRANÇAIS 23 10. UTILISATION QUOTIDIENNE AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 10.3 Ajout du produit de lavage et des additifs 10.1 Activation de l'appareil 1. Branchez l'appareil sur le secteur. 2. Ouvrez le robinet d'eau. 3. Appuyez sur la touche Marche/Arrêt pendant quelques secondes pour allumer l'appareil. Un signal court retentit (si activé). Le sélecteur de programme est automatiquement réglé sur le programme Coton.
www.aeg.com 10.4 Vérifiez la position du volet 1. Tirez le distributeur de produit de lavage jusqu'à la butée. 2. Appuyez sur le levier pour faire sortir le distributeur. 1 2 3. Pour utiliser de la lessive en poudre, tournez le volet vers le haut. 4. Pour utiliser de la lessive liquide, tournez le volet vers le bas. Avec le volet en position BASSE : • N'utilisez pas de lessives liquides gélatineuses ou épaisses. • Ne versez pas de lessive liquide audelà du niveau maximal indiqué sur le volet.
FRANÇAIS 3. Si nécessaire, sélectionnez une ou plusieurs options en appuyant sur les touches correspondantes. Les indicateurs correspondants s'affichent et les informations données changent en conséquence. Si votre sélection n'est pas possible, aucun indicateur ne s'affiche et un signal sonore retentit. 10.6 Départ d'un programme Appuyez sur la touche Départ/Pause pour lancer le programme. Le voyant correspondant cesse de clignoter et reste fixe.
www.aeg.com Dans ce cas, pendant 30 secondes, il est possible de mettre l'appareil en pause et de retirer l'excédent de vêtements. Dès que vous avez retiré l'excédent de vêtements, appuyez sur la touche Départ/Pause pour relancer le programme. La phase ProSense peut être répétée jusqu'à trois fois (voir point 1). Important ! Si vous ne réduisez pas la quantité de linge, le programme de lavage redémarre tout de même, malgré la surcharge. Dans ce cas, les résultats de lavage ne seront pas optimaux.
FRANÇAIS 10.12 Ouverture du hublot Si la température et le niveau de l'eau dans le tambour sont trop élevés et que le tambour continue de tourner, vous ne pouvez pas ouvrir le hublot. Pendant le déroulement d'un programme ou du départ différé, le hublot de l'appareil est verrouillé. 1. Appuyez sur la touche Départ/Pause. Sur l'affichage, le voyant Hublot verrouillé s'éteint. 2. Ouvrez le hublot de l'appareil. Si nécessaire, ajoutez ou retirez des articles. 3.
www.aeg.com • Vous n'utilisez pas l'appareil pendant 5 minutes avant d'appuyer sur la touche Départ/Pause. Appuyez sur la touche Marche/Arrêt pour rallumer l'appareil. • Au bout de 5 minutes après la fin du programme de lavage. Appuyez sur la touche Marche/Arrêt pour remettre l'appareil en marche. L'affichage indique la fin du dernier programme sélectionné. Tournez le sélecteur pour choisir un nouveau cycle.
FRANÇAIS – lessives en poudre pour les textiles délicats (40 °C max.) et les lainages, – lessives liquides, de préférence pour les programmes de lavage à basse température (60 °C max.) pour tous les types de textiles, ou lessives spéciales pour les lainages uniquement. • Ne mélangez pas différents types de produits de lavage. • Afin de préserver l'environnement, n'utilisez que la quantité de produit de lavage recommandée.
www.aeg.com entraîner la formation de mauvaises odeurs et de moisissures. Pour éliminer ces dépôts et assainir l'intérieur de l'appareil, effectuez régulièrement un lavage d'entretien (au moins une fois par mois) : 1. Retirez le linge du tambour. 2. Lancez le programme pour le coton à température maximale avec une petite quantité de lessive en poudre. 1. Ouvrez le distributeur. Appuyez sur le loquet vers le bas comme indiqué sur l'illustration, puis retirez le distributeur. 1 2 12.
FRANÇAIS 31 programme de rinçage sans vêtement dans le tambour. 2 1 12.7 Nettoyage de la pompe de vidange AVERTISSEMENT! Débranchez le cordon d'alimentation de l'appareil de la prise de courant. Vérifiez régulièrement le filtre de la pompe de vidange pour vérifier sa propreté. Nettoyez la pompe de vidange dans le cas où : • L'appareil ne vidange pas. • Le tambour ne tourne pas. • L'appareil fait un bruit inhabituel, car la pompe de vidange est obstruée. • L'écran affiche le code d’alarme 2.
www.aeg.com 2 1 7. Fermez la conduite de vidange et tournez le filtre dans le sens antihoraire pour le retirer. 11. Replacez le filtre dans les guides prévus en le tournant dans le sens horaire. Assurez-vous de visser correctement le filtre pour empêcher les fuites. 2 2 1 1 8. Si nécessaire, retirez les peluches et les débris de la cavité du filtre. 9. Assurez-vous que la turbine de la pompe tourne librement. Si ce n'est pas le cas, contactez votre service après-vente agréé. 12.
FRANÇAIS 12.8 Nettoyage du tuyau d'arrivée d'eau et du filtre de la vanne Il est recommandé de nettoyer occasionnellement les deux filtres du tuyau d'arrivée d'eau et la valve pour éliminer les dépôts accumulés avec le temps : 33 4. Lorsque vous rebranchez le tuyau à l'arrière de l'appareil, tournez-le vers la gauche ou la droite (et non en position verticale) en fonction de la position du robinet. 1. Retirez le tuyau d'arrivée d'eau du robinet et nettoyez le filtre. 1 45° 20° 2 12.
www.aeg.com AVERTISSEMENT! Assurez-vous que la température est supérieure à 0 °C avant d'utiliser à nouveau l'appareil. Le fabricant ne pourra être tenu pour responsable en cas de dommages dus aux basses températures. 13. EN CAS D'ANOMALIE DE FONCTIONNEMENT AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 13.1 Introduction L'appareil ne démarre pas ou s'arrête en cours de programme. Dans un premier temps, essayez de trouver une solution au problème (reportez-vous au tableau).
FRANÇAIS 35 13.2 Pannes possibles Problème Solution possible Le programme ne démarre pas. Assurez-vous que la fiche du câble d'alimentation est bien insérée dans la prise de courant. Vérifiez que le hublot de l'appareil est fermé. Assurez-vous qu'aucun fusible n'est grillé dans la boîte à fusibles. Vérifiez que vous avez bien appuyé sur la touche Départ/ Pause. Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte.
www.aeg.com Problème Solution possible Sélectionnez le programme de vidange si vous avez choisi une option se terminant avec de l'eau dans la cuve. La phase d'essorage n'a Sélectionnez le programme d'essorage. pas lieu ou le cycle de lavage dure plus longtemps que d'habitude. Assurez-vous que le filtre de vidange n'est pas obstrué. Nettoyez le filtre si nécessaire. Reportez-vous au chapitre « Entretien et nettoyage ».
FRANÇAIS Problème 37 Solution possible Utilisez des produits spéciaux pour enlever les taches tenaces avant de laver le linge. Veillez à sélectionner la bonne température. Réduisez la charge de linge. Il y a trop de mousse Réduisez la quantité de produit de lavage. dans le tambour au cours du cycle de lavage. À la fin du cycle de lavage, il y a des résidus de produit de lavage dans le distributeur de produit de lavage.
www.aeg.com 5. Sortez le linge et refermez le hublot. 6. Fermez le volet du filtre. 14. VALEURS DE CONSOMMATION Les données de ce tableau sont approximatives. Les données peuvent varier pour différentes raisons : la quantité et le type de linge, la température ambiante ou de l'eau. Au cours du programme de lavage, la technologie Prosense peut faire varier la durée du lavage et les valeurs de consommation.
FRANÇAIS Mode « Éteint » (W) Mode « Veille » (W) 0.30 0.30 39 Les informations fournies dans le tableau ci-dessus sont conformes à la directive d'application 1015/2010 de la réglementation 2009/125/EC de la commission européenne. 15.
www.aeg.com Lisez attentivement la notice fournie avec l'accessoire. Lisez attentivement les notices fournies avec l'appareil et avec l'accessoire. AVERTISSEMENT! N'installez pas le sèche-linge sous le lave-linge. 16.4 Kit de superposition 16.5 Socle à tiroir Le sèche-linge ne peut-être superposé au-dessus du lave-linge qu'en utilisant le kit de superposition adapté, fabriqué et agréé par AEG. Assurez-vous de la compatibilité du kit de superposition en vérifiant la profondeur de vos appareils.
FRANÇAIS 41 Points de Service Morgenstrasse 131 3018 Bern Zürcherstrasse 204E 9000 St. Gallen Seetalstrasse 11 6020 Emmenbrücke St. Jakob-Turm Birsstrasse 320B 4052 Basel Comercialstrasse 19 7000 Chur Points de vente de rechange Industriestrasse 10, 5506 Mägenwil,Tel. 0848 848 111 Conseil technique/Vente Badenerstrasse 587, 8048 Zürich, Tel.
www.aeg.
FRANÇAIS 43
157006140-A-362016 www.aeg.