L CELEB 125 FR Notice d'utilisation DE Benutzerinformation 2 36
www.aeg.com SOMMAIRE 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. CONSIGNES DE SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTRUCTIONS DE SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 CARACTERISTIQUES TECHNIQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 DESCRIPTION DE L'APPAREIL . . . . . . . . . . . . . . . . . . . . . .
FRANÇAIS 3 1. CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.1 Sécurité des enfants et des personnes vulnérables AVERTISSEMENT Risque d'asphyxie, de blessure ou d'invalidité permanente.
www.aeg.com • Ne modifiez pas les caractéristiques de cet appareil. • Respectez la charge maximale de 7 kg (reportez-vous au chapitre « Tableau des programmes »). • Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son atelier d'entretien ou un technicien qualifié afin d'éviter tout danger.
FRANÇAIS • • • • remplacement du cordon d'alimentation de l'appareil doit être effectué par notre service après-vente. Ne connectez la fiche d'alimentation à la prise de courant qu'à la fin de l'installation. Assurez-vous que la prise de courant est accessible une fois l'appareil installé. Ne tirez jamais sur le câble d'alimentation électrique pour débrancher l'appareil. Tirez toujours sur la prise. Ne touchez jamais le câble d'alimentation ou la prise avec des mains mouillées.
www.aeg.com 3.
FRANÇAIS 11 Dispositifs de protection 7 Pour désactiver ce dispositif, tournezle dans le sens inverse des aiguilles d’une montre jusqu’à ce que la rainure soit verticale. 12 Pieds pour que l'appareil soit de niveau 4.1 Sécurité enfants • Lorsque ce dispositif est activé, vous ne pouvez pas fermer le hublot. Ceci évite d'enfermer un enfant ou un animal dans l'appareil par accident. Pour activer ce dispositif, tournez-le dans le sens des aiguilles d’une montre jusqu’à ce que la rainure soit horizontale.
www.aeg.com 5 Touche Départ différé (Startuitstel - Départ Différé) 6 Touche Gain de temps (Tijd Besparen - Gain de Temps) 7 Touche Rinçage plus (Extra Spoelen - Rinçage+) 8 Touche Taches (Vlekken - Taches) 9 Touche Essorage réduit (T/min.) 10 Touche Température (Temp. ºC) 5.1 Bouton marche/arrêt 1 Appuyer sur ce bouton pour activer ou désactiver le lave-linge. Une tonalité retentit lorsque le lave-linge est activé.
FRANÇAIS 9 Vous ne pouvez pas ouvrir le hublot de l'appareil lorsque ce symbole est allumé. Vous ne pouvez ouvrir le hublot de l'appareil que lorsque ce symbole est éteint. Si le programme est terminé mais que le symbole reste allumé : • Il y a de l'eau dans le tambour. • La fonction « Arrêt cuve pleine » est activée. Départ différé D • La durée du programme Une fois que le programme a démarré, cette durée diminue par intervalles d'une minute.
www.aeg.com Utilisez cette fonction pour les personnes allergiques aux produits de lavage et dans les régions où l'eau est douce. 5.8 Touche Taches 8 Appuyez sur la touche 8 pour ajouter la phase Taches à un programme. Utilisez cette fonction pour le linge très taché. Quand vous programmez cette fonction, placez le détachant dans le comparti. ment Cette fonction allonge la durée du programme. Cette fonction n'est pas compatible avec des températures inférieures à 40 °C. 5.
FRANÇAIS 11 6. PROGRAMMES Programme Température Type de charge Charge max. Description du cycle Fonctions Katoen – Blanc/ Couleurs Blanc/Couleurs 95° - Froid Coton blanc et couleurs normalement sales. Max. 7 kg Lavage Rinçages Essorage long RÉDUCTION DE LA VITESSE D'ESSORAGE ARRÊT CUVE PLEINE TACHES RINÇAGE PLUS GAIN DE TEMPS1) Katoen + Voor- Coton blanc et couwas – Blanc/ leurs très sales. Couleurs + Pré- Max.
www.aeg.com Programme Température Type de charge Charge max. Description du cycle Fonctions Fijne Was - Délicats Délicats 40° - Froid Vêtements en textiles délicats tels que l'acrylique, la viscose ou le polyester, normalement sales. Max. 3 kg Lavage Rinçages Essorage court RÉDUCTION DE LA VITESSE D'ESSORAGE ARRÊT CUVE PLEINE TACHES3) RINÇAGE PLUS GAIN DE TEMPS1) Wol / Zijde Laine/Soie Laine/Soie Vêtements en laine Lavage lavables en machiRinçages ne.
FRANÇAIS Programme Température Type de charge Charge max. Super Eco6) Froid Textiles mixtes (arti- Lavage cles en coton et Rinçages synthétiques). Essorage long Max. 3 kg RÉDUCTION DE LA VITESSE D'ESSORAGE ARRÊT CUVE PLEINE RINÇAGE PLUS Katoen Eco - Coton Eco Coton Eco Vêtements en coton Lavage blanc et couleurs Rinçages grand teint norma- Essorage long lement sales. Max.
www.aeg.com Programme1) Type de charge Charge max. La vapeur peut être utilisée sur du linge sec, lavé ou porté une seule fois. Ces programmes peuvent atténuer les plis et les odeurs et rendre votre linge plus souple. N'utilisez aucun produit de lavage. En cas de besoin, nettoyez les taches en effectuant un cycle de lavage ou à l'aide d'un produit détachant à application locale. Les programmes Vapeur n'effectuent pas de cycle de lavage hygiénique.
FRANÇAIS Programmes 15 Charge (kg) Consommation énergétique (kWh) Consommation d'eau (litres) Durée approximative du programme (minutes) Taux d'humidité restant (%)1) Coton 60 °C 7 1.1 60 180 52 Coton 40 °C 7 0.9 60 160 52 Synthétiques 40 °C 3.5 0.7 50 100 35 Textiles délicats 40 °C 3 0.5 65 80 35 Laine/Lavage à la main 30 °C 2 0.4 55 60 30 Programmes coton standard Coton 60 °C standard 7 0.91 49 207 52 Coton 60 °C standard 3.5 0.
www.aeg.com 6. Sélectionnez et lancez le programme de lavage en fonction de la charge et du degré de salissure. 9.1 Chargement du linge 1. 2. Placez les articles un à un dans le tambour en les dépliant le plus possible. Assurez-vous de ne pas surcharger le tambour. 3. Fermez la porte de l'appareil. Ouvrez la porte de l'appareil. Assurez-vous de ne pas coincer de linge entre le joint et la porte. Risque de fuite d'eau ou de détérioration du linge. 9.
FRANÇAIS 17 Languette pour lessive en poudre ou liquide Tournez-la (vers le haut ou vers le bas) en position correcte pour utiliser la lessive en poudre ou liquide. Respectez toujours les instructions figurant sur l'emballage des lessives. Vérifiez la position de la languette. 1. Tirez le panier supérieur jusqu'à la butée. 2. Poussez le levier vers le bas pour enlever le distributeur. 3. Pour utiliser de la lessive en poudre, tournez la languette vers le haut. 4.
www.aeg.com vous pouvez régler un nouveau programme de lavage. 9.3 Réglage et départ d'un programme 1. Tournez le sélecteur de programmes. Le voyant correspondant s'allume. 2. Le voyant de la touche 4 clignote en rouge. 3. L'écran affiche la température et la vitesse d'essorage par défaut. Pour modifier la température et/ou la vitesse d'essorage, appuyez sur les touches correspondantes. 4. Sélectionnez les fonctions compatibles.
FRANÇAIS Pendant le déroulement d'un programme ou du départ différé, le hublot de l'appareil est verrouillé. Pour ouvrir le hublot de l'appareil : 1. Appuyez sur la touche 4 . Le symbole de verrouillage de la porte disparaît de l'écran. 2. Ouvrez le hublot de l'appareil. 3. Fermez le hublot de l'appareil et appuyez sur la touche 4 . Le programme ou le départ différé se poursuit. 9.10 À la fin du programme • L'appareil se met à l'arrêt automatiquement. • Les signaux sonores retentissent.
www.aeg.com deaux dans un sac de lavage ou une taie d'oreiller. • Ne lavez pas dans l'appareil : – Le linge sans ourlet ou déchiré – Les soutien-gorges à armatures. – Utilisez un sac de lavage pour les articles très petits. • Un très petite charge peut provoquer des problèmes d'équilibre pendant la phase d'essorage. Si cela se produit, répartissez manuellement les articles dans la cuve et lancez à nouveau la phase d'essorage.
FRANÇAIS 21 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT Déconnectez l'appareil de l'alimentation électrique avant de le nettoyer. 11.1 Détartrage de l’appareil L'eau du robinet contient du calcaire. Si cela s'avère nécessaire, utilisez un adoucisseur d'eau pour éliminer le tartre. Utilisez un produit spécialement conçu pour les lave-linge. Respectez les instructions inscrites sur l'emballage par le fabricant. Procédez séparément d'un lavage de linge. 11.
www.aeg.com 11.6 Distributeur de produit de lavage Pour nettoyer le distributeur : 1 1. 2. Appuyez sur le levier. Sortez le panier. 3. Retirez la partie supérieure du compartiment de l'additif liquide. Nettoyez tous les éléments sous l'eau courante. 2 4. 5. 6. 11.7 Pompe de vidange Examinez régulièrement la pompe de vidange et assurez-vous qu'elle est propre. Nettoyez la pompe si : • L'appareil ne vidange pas. • Le tambour ne tourne pas.
FRANÇAIS 23 Pour nettoyer la pompe de vidange : 1. Ouvrez le volet de la pompe. 2. Enlevez la languette en tirant dessus. 3. Insérez un récipient sous le panier de la pompe de vidange pour recueillir l'eau qui s'écoule. Appuyez sur les deux leviers et tirez la conduite de vidange vers l'avant pour évacuer l'eau. 4. 1 5. 6. 2 Lorsque le récipient est rempli, remettez la conduite de vidange en place et videz le récipient.
www.aeg.com 9. Nettoyez le filtre sous l'eau courante et remettez-le en place dans la pompe en l'insérant dans les glissières prévues spécialement à cet effet. 10. Assurez-vous de visser correctement le filtre pour empêcher les fuites. 11. Replacez la languette et fermez le volet de la pompe de vidange. 2 1 11.8 Le filtre du tuyau d'arrivée d'eau et le filtre de la soupape • Le voyant de la touche 4 clignote et l'alarme correspondante s'affiche.
FRANÇAIS 11.9 Vidange d'urgence : L'appareil ne vidange pas à cause d'une anomalie de fonctionnement. Si cela se produit, procédez aux étapes (1) à (6) du paragraphe « Pour nettoyer la pompe de vidange ». Nettoyez la pompe, si besoin. Remettez la conduite de vidange en place et fermez le volet de la pompe de vidange. Lorsque vous appliquez la procédure de vidange d'urgence, vous devez réactiver le système de vidange : 1. Versez 2 litres d'eau dans le compartiment pour le lavage principal. 2.
www.aeg.com Problème L'appareil ne vidange pas l'eau. Cause probable Solution possible Le robinet d'arrivée d'eau est obstrué ou incrusté de tartre. Nettoyez le robinet d'eau. Le tuyau d'arrivée d'eau est mal raccordé. Assurez-vous que le raccordement est correct. La pression de l'eau est trop faible. Contactez votre compagnie des eaux. L'extrémité du tuyau de vidange est placée trop bas. Vérifiez que la position du tuyau de vidange est correcte. Le tuyau d'évacuation de l'eau est endommagé.
FRANÇAIS Problème Cause probable 27 Solution possible Un fusible a grillé dans Remplacez le fusible. la boîte à fusibles de votre habitation. Il y a de l'eau sur le sol. Impossible d'ouvrir le hublot de l'appareil. Vous n'avez pas appuyé sur la touche 4 . Appuyez sur la touche 4 . Le départ différé est sélectionné. Pour démarrer immédiatement le programme, annulez le départ différé. La sécurité enfants est activée. Désactivez la sécurité enfants.
www.aeg.com Problème Cause probable Solution possible Les résultats de la- Le produit de lavage vage ne sont pas que vous utilisez n'est satisfaisants. pas suffisant ou n'est pas adéquat. Augmentez la quantité de produit de lavage ou utilisez-en un autre mieux adapté. Vous n'avez pas enlevé Utilisez des produits spéciaux les taches tenaces avant pour traiter les taches tenaces. de laver le linge. Une température incorrecte a été sélectionnée. Veillez à sélectionner la bonne température.
FRANÇAIS 29 4. Tirez le dispositif de déverrouillage d'urgence vers le bas tout en ouvrant le hublot de l'appareil. 5. Retirez le linge. 6. Fermez le volet du filtre. 14. INSTALLATION 14.1 Kit de plaques de fixation (4055171146) Disponible auprès de votre magasin vendeur. Si vous installez l'appareil sur un socle, stabilisez l'appareil à l'aide des plaques de fixation. Suivez les instructions fournies avec le kit. 14.2 Déballage 1. Servez-vous de gants. Retirez le film externe.
www.aeg.com 4. Retirez le film interne. 5. Ouvrez le hublot. Retirez la cale en polystyrène du joint du hublot et tous les articles présents dans le tambour. 6. Placez l'une des cales en polystyrène au sol derrière l'appareil. Couchez avec soin l'appareil sur le dos. Assurez-vous de ne pas endommager les tuyaux. 7. Retirez la base en polystyrène en bas de l'appareil. Remettez l'appareil en position verticale. 8.
FRANÇAIS 9. 31 Retirez le câble d'alimentation électrique et le tuyau de vidange de leurs supports. 10. Desserrez les trois boulons. Utilisez la clé fournie avec l'appareil. 11. Retirez les entretoises en plastique. 12. Mettez les bouchons en plastique dans les orifices. Ces bouchons se trouvent dans le même sachet que la notice d'utilisation. AVERTISSEMENT Retirez toutes les attaches de transport et les dispositifs de sécurité avant d'installer l'appareil.
www.aeg.com 14.3 Positionnement et mise à niveau • Placez l'appareil sur un sol plat et dur. • Assurez-vous que la circulation de l'air sous l'appareil ne soit pas entravée par des tapis. • Veillez à ce que l'appareil ne touche pas le mur ou les autres meubles. • Desserrez ou serrez les pieds jusqu'à ce que l'appareil soit de niveau. Une mise à niveau correcte évite les vibrations, le bruit ou des déplacements de l'appareil au cours de son fonctionnement. x4 • L'appareil doit être de niveau et stable.
FRANÇAIS 33 • Raccordez le tuyau d'arrivée d'eau à un robinet fileté (3/4 po). ATTENTION Assurez-vous que les raccords ne fuient pas. N'utilisez pas de rallonge si le tuyau d'alimentation est trop court. Contactez le service aprèsvente pour remplacer le tuyau d'alimentation. Dispositif d'arrêt de l'eau A 14.5 Vidange de l'eau Il existe différentes procédures pour raccorder le tuyau de vidange : Avec le guide de tuyau en plastique.
www.aeg.com • Sur le bord d'un évier. • Veillez à ce que le guide de tuyau en plastique ne puisse pas se déplacer quand l'appareil se vidange. Fixez le guide au robinet d'arrivée d'eau ou au mur. • À une conduite fixe dotée d'une ventilation spéciale. Reportez-vous à l'illustration. Directement dans une conduite d'évacuation murale, à une hauteur du sol comprise entre 60 et 100 cm.
FRANÇAIS 35 15. EN MATIÈRE DE PROTECTION DE L'ENVIRONNEMENT Recyclez les matériaux portant le symbole . Déposez les emballages dans les conteneurs prévus à cet effet. Contribuez à la protection de l'environnement et à votre sécurité, recyclez vos produits électriques et électroniques. Ne jetez pas les appareils portant le symbole avec les ordures ménagères. Emmenez un tel produit dans votre centre local de recyclage ou contactez vos services municipaux.
www.aeg.com INHALT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. SICHERHEITSINFORMATIONEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SICHERHEITSHINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TECHNISCHE DATEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GERÄTEBESCHREIBUNG . . . . . . . . . . . . . . . . . . . . . . . . . .
DEUTSCH 37 1. SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Sicherheit von Kindern und schutzbedürftigen Personen WARNUNG! Es besteht Erstickungsgefahr, Risiko von Verletzungen oder permanenten Behinderungen.
www.aeg.com • Nehmen Sie keine technischen Änderungen am Gerät vor. • Beachten Sie die maximale Beladungsmenge von 7 kg (siehe Kapitel „Programmtabelle“). • Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, einem autorisierten Kundendienst oder einer gleichermaßen qualifizierten Person ersetzt werden, um Gefahrenquellen zu vermeiden. • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen.
DEUTSCH • • • • • • • chen. Wenden Sie sich andernfalls an eine Elektrofachkraft. Das Gerät darf ausschließlich an eine ordnungsgemäß installierte Schutzkontaktsteckdose angeschlossen werden. Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie dies durch unseren Kundendienst durchführen.
www.aeg.com 3. TECHNISCHE DATEN Abmessungen Breite / Höhe / Tiefe Elektrischer Anschluss: 600 / 850 / 605 mm Gesamttiefe 640 mm Spannung Gesamtleistung Sicherung Frequenz 230 V 2200 W 10 A 50 Hz Die Schutzklasse gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt Wasserdruck IPX4 Min. 0,5 bar (0,05 MPa) Max.
DEUTSCH 7 Schraubfüße zum Ausrichten des Geräts 8 Wasserablaufschlauch 9 Wassereinlassventil 10 Netzkabel 11 Transportschrauben 12 Schraubfüße zum Ausrichten des 41 mel eingeschlossen werden können. Zum Aktivieren der Kindersicherung drehen Sie den Schalter im Uhrzeigersinn, bis die Einkerbung horizontal ist. Zum Deaktivieren der Kindersicherung drehen Sie den Schalter gegen den Uhrzeigersinn, bis die Einkerbung vertikal ist. Geräts 4.
www.aeg.com 5. BEDIENFELD 1 2 3 Katoen Eco Coton Eco 10 1 Ein-/Aus-Taste (Aan/Uit - Marche/Ar- rêt) 2 Programmwahlschalter 3 Display 4 Start/Pause-Taste (Start/Pauze - Dé- part/Pause) 5 Zeitvorwahl-Taste (Startuitstel - Dé- part Différé) 6 Zeitsparen-Taste (Tijd Besparen - Gain de Temps) 7 Extra Spülen-Taste (Extra Spoelen - Rinçage+) 8 Flecken-Taste (Vlekken - Taches) 9 Drehzahlreduzierungstaste (T/min.
DEUTSCH 43 Im Display erscheint: A • Die maximale Temperatur des Programms B • Die Standard-Schleuderdrehzahl des Programms • Die Symbole „Kein Schleudergang“1) und „Spülstopp“ C • Die Display-Symbole2) Symbol Beschreibung Hauptwaschgang Spülgänge Schleudergang Kindersicherung Sie können die Tür des Geräts nicht öffnen, solange dieses Symbol erscheint. Sie können die Tür erst öffnen, wenn das Symbol erlischt.
www.aeg.com 5.4 Start-/Pause-Taste 4 Drücken Sie die Taste 4 , um ein Programm zu starten oder zu unterbrechen. 5.5 Zeitvorwahl-Taste 5 Drücken Sie die Taste 5 , um den Start eines Programms um 30 Minuten bis 20 Stunden zu verzögern. 5.6 Zeitspar-Taste 6 Drücken Sie die Taste 6 , um die Programmdauer zu verkürzen. • Drücken Sie die Taste einmal, um die Programmdauer für normal verschmutzte Wäsche zu verkürzen.
DEUTSCH • Drücken Sie zum Aktivieren der Funktion die Tasten 10 und 9 gleichzeitig so lange, bis im Display das Symbol erscheint. • Drücken Sie zum Deaktivieren der Funktion die Tasten 10 und 9 gleichzeitig so lange, bis das Symbol im Display erlischt. Wenn Sie die Funktion aktiveren • Bevor Sie die Start/Pause-Taste 4 drücken, kann das Gerät nicht starten. • Nachdem Sie die Start/Pause-Taste drücken 4 , sind alle Tasten und der Programmwahlschalter deaktiviert.
www.aeg.com Programm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Synthetica Synthétiques Pflegeleicht 60 °C - Kalt Synthetik- oder Mischgewebe, normal verschmutzt. Max. 3.5 kg Hauptwaschgang Spülgänge Kurzer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP FLECKEN EXTRA SPÜLEN ZEITSPAREN1) Strijkvrij - Repassage Facile Leichtbügeln2) 60 °C - Kalt Synthetikfasern, Hauptwaschgang normal verschmutzt. Spülgänge Max. 3.
DEUTSCH 47 Programm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen 20 Min. - 3 kg 30° Teile aus Baumwolle oder Synthetik, die leicht verschmutzt sind oder nur einmal getragen wurden. Hauptwaschgang Spülgänge Kurzer Schleudergang DREHZAHLREDUZIERUNG Super Eco6) Kalt Mischfasern (Baumwolle und Synthetik). Max.
www.aeg.com DAMPFPROGRAMME Programm1) Beladung Max. Beladung Opfrissen - Rafraîchir Dampf Auffrischen Dieses Programm beseitigt Gerüche aus der Wäsche. Baumwolle und pflegeleichte Wäschestücke. bis zu 1.5 kg Baumwolle und pflegeleichte Wäschestücke. bis zu 1.5 kg Dampf beseitigt keine Tiergerüche. Ontkreuk - Défroissage Dampf Glätten Dieses Programm hilft bei der Beseitigung von Falten in der Wäsche. Dampf kann für getrocknete, gewaschene oder einmal getragene Wäsche benutzt werden.
DEUTSCH 49 7. VERBRAUCHSWERTE Am Programmstart zeigt das Display die Programmdauer für die maximale Beladung an. Während der Waschphase wird die Programmdauer automatisch berechnet und verringert sich möglicherweise beträchtlich, wenn die Wäsche weniger wiegt als die maximal zulässige Beladung. Zum Beispiel beträgt die maximale Beladung bei Baumwolle 60 °C 7 kg und die Programmdauer überschreitet 2 Stunden. Wiegt die tatsächliche Beladung 1 kg, verringert sich die Programmdauer auf unter 1 Stunde.
www.aeg.com Aus-Zustand (W) Ein-Zustand (W) Die in den Tabellen oben enthaltenen Informationen erfüllen die Verordnung 1015/2010 der EU-Kommission zur Durchführung der Richtlinie 2009/125/EC. 8. VOR DER ERSTEN INBETRIEBNAHME 1. Zum Aktivieren des Ablaufsystems füllen Sie 2 Liter Wasser in das Hauptfach der Waschmittelschublade. 2. Geben Sie eine kleine Waschmittelmenge in das Hauptfach der Waschmittelschublade.
DEUTSCH 51 9.2 Verwendung von Wasch- und Pflegemitteln Waschmittelfach für die Vorwaschphase und das Einweichprogramm. Füllen Sie das Waschmittel für den Vorwaschgang und das Einweichen vor dem Start des Programms ein. Waschmittelfach für die Waschphase. Wenn Sie Flüssigwaschmittel verwenden, muss dieses direkt vor dem Start des Programms eingefüllt werden. Fach für flüssige Pflegemittel (Weichspüler, Stärke). Füllen Sie das Pflegemittel in das Fach ein, bevor Sie das Programm starten.
www.aeg.com 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. Klappe in der Position „Unten“: – Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. – Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. – Stellen Sie nicht den Vorwaschgang ein. – Stellen Sie nicht die Zeitvorwahl ein. 5. 6. Messen Sie Waschmittel und Weichspüler ab.
DEUTSCH 53 9.4 Unterbrechen eines Programms 9.8 Abbrechen der Zeitvorwahl 1. Drücken Sie die Taste 4 . Die Kontrolllampe blinkt. 1. Drücken Sie die Taste 4 . Die zugehörige Kontrolllampe blinkt. 2. Drücken Sie die Taste 4 erneut. Das Waschprogramm wird fortgesetzt. 2. Drücken Sie die Taste 5 wiederholt, bis das Display 0’ anzeigt. 3. Drücken Sie die Taste 4 . Das Programm startet. 9.5 Abbrechen eines Programms 1.
www.aeg.com • Lassen Sie die Tür offen, damit sich kein Schimmel und keine unangenehmen Gerüche bilden. • Schließen Sie den Wasserhahn. Das Waschprogramm ist beendet, aber es steht Wasser in der Trommel: – Die Trommel dreht sich regelmäßig, um Knitterfalten in der Wäsche zu vermeiden. – Die Tür bleibt verriegelt. – Sie müssen das Wasser abpumpen, um die Tür zu öffnen. 2. Drücken Sie die Start/Pause-Taste 4 . Das Gerät pumpt das Wasser ab und schleudert. 3.
DEUTSCH • Verwenden Sie die korrekten Produkte für Art und Farbe des Gewebes, Programmtemperatur und Verschmutzungsgrad. • Stellen Sie keine Vorwäsche ein, wenn Sie Flüssigwaschmittel verwenden. • Ist Ihr Gerät nicht mit einer Klappe in der Waschmittelschublade ausgerüstet, geben Sie das Flüssigwaschmittel in eine Dosierkugel. 10.4 Wasserhärte Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Enthärters für 55 Waschmaschinen.
www.aeg.com • Stellen Sie das heißeste Waschprogramm für Koch-/Buntwäsche ein. • Verwenden Sie die korrekte Menge eines Waschpulvers mit biologischen Reinigungseigenschaften. Lassen Sie die Tür nach jedem Waschprogramm einige Zeit offen stehen, um einer Schimmelbildung vorzubeugen und unangenehme Gerüche entweichen zu lassen. 11.4 Türdichtung Überprüfen Sie regelmäßig die Türdichtung und nehmen Sie alle Einzelteile aus dem Inneren heraus. 11.
DEUTSCH 5. 6. 57 Reinigen Sie das leere Einschubfach mit einer Bürste. Schieben Sie die Waschmittelschublade wieder in das Einschubfach ein. WARNUNG! 1. Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Entfernen Sie den Filter nicht, während das Gerät in Betrieb ist. Reinigen Sie die Ablaufpumpe nicht, wenn das Wasser im Gerät heiß ist. Das Wasser muss abgekühlt sein, bevor Sie die Ablaufpumpe reinigen. 11.
www.aeg.com 5. 1 6. 2 2 1 11.8 Zulaufschlauchfilter und Ventilfilter Die Filter müssen in folgenden Fällen gereinigt werden: • Es läuft kein Wasser in das Gerät. • Das Wasser läuft sehr lange in das Gerät ein. Wenn der Behälter mit Wasser voll ist, stecken Sie den Ablaufkanal wieder ein und leeren Sie den Behälter aus. Wiederholen Sie die Schritte 4 und 5, bis kein Wasser mehr aus der Ablaufpumpe ausläuft.
DEUTSCH 59 So reinigen Sie die Wasserzulauffilter: Schließen Sie den Wasserhahn. Entfernen Sie den Wasserzulaufschlauch vom Wasserhahn. 3. Reinigen Sie den Filter im Zulaufschlauch mit einer harten Bürste. 1. 2. 4. 5. 6. 20° 45° 7. Entfernen Sie den Zulaufschlauch von der Geräterückseite. Reinigen Sie den Filter im Ventil mit einer harten Bürste oder einem Handtuch. Bringen Sie den Zulaufschlauch wieder an.
www.aeg.com WARNUNG! Vergewissern Sie sich vor einer erneuten Benutzung des Geräts, dass die Temperatur mehr als 0 °C beträgt. Der Hersteller ist nicht verantwortlich für Schäden, die durch niedrige Temperaturen entstanden sind. 12. FEHLERSUCHE Das Gerät startet nicht oder stoppt während des Betriebs. Versuchen Sie zunächst eine Lösung für das Problem zu finden (siehe Tabelle). Wenn Sie keine Lösung finden, wenden Sie sich an den Kundendienst. • - Das Gerät pumpt das Wasser nicht ab.
DEUTSCH 61 Problem Mögliche Ursache Mögliche Abhilfe Das Gerät pumpt das Wasser nicht ab. Der Wasserablaufschlauch ist beschädigt. Vergewissern Sie sich, dass der Wasserablaufschlauch keine Beschädigungen aufweist. Der Filter der Ablaufpumpe ist verstopft. Reinigen Sie den Filter der Ablaufpumpe. Siehe „Reinigung und Pflege“. Der Wasserablaufschlauch ist nicht richtig angeschlossen. Vergewissern Sie sich, dass die Schlauchverbindung in Ordnung ist.
www.aeg.com Problem Mögliche Ursache Mögliche Abhilfe Es befindet sich Wasser auf dem Boden. An den Schlauchanschlüssen tritt Wasser aus. Vergewissern Sie sich, dass die Schlauchanschlüsse fest angeschlossen sind. An der Ablaufpumpe tritt Wasser aus. Vergewissern Sie sich, dass der Ablaufpumpenfilter fest sitzt. Der Wasserablaufschlauch ist beschädigt. Vergewissern Sie sich, dass der Wasserzulaufschlauch nicht beschädigt ist. Die Tür des GeKein Strom. räts lässt sich nicht öffnen.
DEUTSCH Problem Mögliche Ursache Mögliche Abhilfe Es wurde eine falsche Temperatur eingestellt. Achten Sie darauf, die richtige Temperatur einzustellen. 63 Es befindet sich zu viel Verringern Sie die Beladung. Wäsche in der Trommel. Schalten Sie das Gerät nach der Überprüfung wieder ein. Das Programm wird an der Stelle fortgesetzt, an der es unterbrochen wurde. Tritt das Problem erneut auf, wenden Sie sich an den Kundendienst.
www.aeg.com 6. Schließen Sie die Filterklappe. 14. MONTAGE 14.1 Satz Fixierplatten (4055171146) Sie erhalten den Bausatz bei Ihrem Vertragshändler. Wenn Sie das Gerät auf einem Sockel aufstellen, befestigen Sie es mithilfe der Fixierplatten. Lesen Sie aufmerksam die dem Bausatz beiliegende Anleitung. 14.2 Auspacken 1. Verwenden Sie Handschuhe. Entfernen Sie die äußere Folie. Benutzen Sie, falls erforderlich, ein Teppichmesser. 2. Nehmen Sie die Karton-Abdeckung ab.
DEUTSCH 65 5. Öffnen Sie die Tür. Entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel. 6. Legen Sie eines der Styroporverpackungsteile hinter dem Gerät auf den Boden. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 8. 1 2 9.
www.aeg.com 10. Lösen Sie die drei Schrauben. Ver- wenden Sie dazu den mitgelieferten Schraubenschlüssel. 11. Ziehen Sie die Kunststoff-Abstandshalter heraus. 12. Setzen Sie die Kunststoffkappen in die Öffnungen. Diese Kappen finden Sie im Beutel mit der Gebrauchsanleitung. WARNUNG! Entfernen Sie vor der Montage des Geräts alle Verpackungsmaterialien und Transportschrauben. Wir empfehlen, Verpackungsmaterial und Transportschrauben für einen späteren Transport aufzubewahren. 14.
DEUTSCH 67 • Das Gerät muss einen waagerechten und festen Stand haben. VORSICHT! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 14.4 Wasserzulaufschlauch • Schließen Sie den Schlauch am Gerät an. Drehen Sie den Wasserzulaufschlauch nur nach links oder rechts. Lösen Sie die Ringmutter, um ihn in die gewünschte Position zu bewegen. 20 O 45 O • Schließen Sie den Wasserzulaufschlauch an einen Kaltwasserhahn mit einem 3/4"-Außengewinde an.
www.aeg.com Aquastopp-Einrichtung A Der Zulaufschlauch verfügt über eine Wasserstopp-Vorrichtung. Damit werden Wasserlecks am Schlauch, die durch natürliche Alterung auftreten könnten, verhindert. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an. Tritt dieser Fall ein, drehen Sie den Wasserhahn zu und wenden Sie sich an den Kundendienst, um den Schlauch zu erneuern. 14.5 Wasserablauf Es gibt mehrere Möglichkeiten, den Ablaufschlauch anzuschließen: Mit der Kunststoff-Schlauchführung.
DEUTSCH 69 Ohne Kunststoff-Schlauchführung. • An einen Siphon. Orientieren Sie sich an der Abbildung. Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Stellen Sie sicher, dass der Schlauch einen Bogen beschreibt, damit kein Schmutz aus dem Siphon in das Gerät gelangen kann. • Direkte Einleitung in ein Abflussrohr in der Zimmerwand. Mit einer Schlauchschelle befestigen. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
www.aeg.
DEUTSCH 71
132909000-A-372013 www.aeg.