LFX 7C1613B USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE.................................................................................................3 2. SICHERHEITSANWEISUNGEN...................................................................................... 4 3. MONTAGE.......................................................................................................................6 4. GERÄTEBESCHREIBUNG..........................................................................................
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie die mitgelieferte Gebrauchsanleitung sorgfältig vor Montage und Inbetriebnahme des Geräts. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com 1.2 Allgemeine Sicherheit • • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Überschreiten Sie nicht die maximale Beladungsmenge von 10 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • • • • • • • • • verriegeln und dadurch interne Schäden zu vermeiden. Seien Sie beim Bewegen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk. Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. Halten Sie sich an die mitgelieferte Montageanleitung. Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist.
www.aeg.com • Berühren Sie während des Betriebs nicht die Glastür. Das Glas kann sehr heiß werden. 2.5 Service • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. 2.6 Entsorgung • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung. • Schneiden Sie das Netzkabel in der Nähe des Geräts ab, und entsorgen Sie es.
DEUTSCH 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. Aus dem Ablaufschlauch könnte Wasser austreten. Dies ist auf den Gerätetest mit Wasser im Werk zurückzuführen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 10.
www.aeg.com Das Gerät muss einen waagerechten und festen Stand haben. Durch eine korrekte waagrechte Ausrichtung des Geräts werden Vibrationen, Geräusche und ein Wandern des Geräts während des Betriebs vermieden. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren. 3.2 Aufstellen und Ausrichten 1. Stellen Sie das Gerät auf einen ebenen, festen Boden. Stellen Sie sicher, dass die Luftzirkulation unter dem Gerät nicht durch Teppiche beeinträchtigt wird.
DEUTSCH 1. Formen Sie den Ablaufschlauch zu einem U und verlegen Sie ihn in der Kunststoffführung. VORSICHT! Achten Sie darauf, dass die Anschlüsse dicht sind. Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist. Wenden Sie sich an den Kundendienst, um einen anderen Zulaufschlauch zu erhalten. 2. Am Rande eines Beckens Befestigen Sie die Führung am Wasserhahn oder an der Wand. Stellen Sie sicher, dass die Kunststoffführung beim Abpumpen nicht herausrutschen kann. 3.
www.aeg.com mit einer Schlauchschelle. Orientieren Sie sich an der Abbildung. Das Ende des Ablaufschlauchs muss stets belüftet sein, d. h. der Innendurchmesser des Ablaufrohrs (min. 38 mm min. 1,5) muss größer sein als der Außendurchmesser des Ablaufschlauchs. 4. Sieht das Ende des Ablaufschlauchs so aus (siehe Abbildung), können Sie es direkt in das Standrohr drücken. 5.
DEUTSCH • Dank der Option Soft Plus wird der Weichspüler gleichmäßig in der Wäsche verteilt, sodass er die Fasern durchdringt und für perfekte Weichheit sorgt. 4.
www.aeg.com 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 Programme Eco Baumwolle Pflegeleicht Feinwäsche Wolle/Seide Dampf Anti-Allergie 20 min. - 3 kg 4 Zeit Sparen Nur Spülen Nur Schleudern Nur Abpumpen Outdoor Daunen Jeans Temp. U./Min. Flecken/ Vorw.
DEUTSCH 13 5.2 Display Anzeige der max. Beladung. Das Symbol blinkt während der Messung der Wäschemenge (siehe Abschnitt „PROSENSE Beladungserkennung“). Anzeige des max. zulässigen Wäschegewichts. Blinkt, wenn das Wäschegewicht die maximal zulässige Füllmenge für das ausgewählte Programm überschreitet. Zeitvorwahlanzeige. Türverriegelungsanzeige. Die Digitalanzeige zeigt Folgendes an: • Programmdauer (z. B. • Zeitvorwahl (z. B. ). oder ). • Programmende ( ). • Fehlercode (z. B. ).
www.aeg.com Zeitsparanzeige. Temperaturanzeige. Die Anzeige kaltem Wasser gewählt wurde. erscheint, wenn ein Waschgang mit Schleuderdrehzahlanzeige. Spülstoppanzeige. Anzeige Extra Leise. Vorwaschphasenanzeige. Fleckenanzeige. Anzeige Extra Spülen 6. DREHSCHALTER UND TASTEN 6.1 Ein/Aus 6.3 Temp. Halten Sie diese Taste einige Sekunden lang gedrückt, um das Gerät ein- oder auszuschalten. Beim Ein- und Ausschalten ertönen zwei verschiedene Melodien.
DEUTSCH Das Waschprogramm endet mit Wasser in der Trommel und der letzte Schleudergang wird nicht durchgeführt. Auf dem Display erscheint die Anzeige . Die Trommel dreht sich regelmäßig, um Knitterfalten in der Wäsche zu vermeiden. Die Tür bleibt verriegelt. Die Trommel dreht sich regelmäßig, um Knitterfalten in der Wäsche zu vermeiden. Sie müssen das Wasser abpumpen, um die Tür entriegeln zu können. Berühren Sie die Taste Start/Pause. Das Gerät führt den Schleudergang aus und pumpt das Wasser ab.
www.aeg.com Wenn Extra Spülen als standardmäßige Option eingestellt ist und Sie ein kompatibles Waschprogramm wählen, Wenn Sie ein Baumwollprogramm mit 40 °C oder 60 °C wählen, erscheint im Display die . Das sind Anzeige die standardmäßigen Baumwollprogramme, die hinsichtlich des Energie- und Wasserverbrauchs am effizientesten sind. an. In zeigt das Display diesem Fall kann durch Drücken der Taste Extra Spülen nur ein Spülgang hinzugefügt werden. 6.7 Plus Dampf 6.
DEUTSCH Bei viermaliger Berührung zeigt das Gerät wieder die Standardeinstellungen des Waschprogramms an. 6.11 Zeitvorwahl 17 Schritten von 30 Minuten bis 90 Minuten und in Schritten von 2 Stunden bis zu 20 Stunden. Nach Berührung der Taste Start/Pause zeigt das Display die Anzeige und die gewähte Zeitvorwahl an und das Gerät startet den Countdown. Mit dieser Option können Sie den Programmstart verzögern, um eine günstigere Zeit zu nutzen. 6.
www.aeg.com Programm Programmbeschreibung Dampf Dampfprogramm für Baumwolle und pflegeleichte Wäsche.Dampf kann für getrocknete Wäsche verwendet werden2), gewaschene oder einmal getragene Wäschestücke verwendert werden. Dieses Programm reduziert Falten und Gerüche3) und lockert die Fasern auf. Nehmen Sie nach Ablauf des Programms die Wäsche schnell aus der Trommel. Nach einem Dampfprogramm lässt sich die Wäsche mühelos bügeln. Verwenden Sie kein Waschmittel.
DEUTSCH Programm Outdoor 19 Programmbeschreibung Synthetische Sportbekleidung. Dieses Programm eignet sich zur schonenden und schnellen Wäsche von moderner Sportbekleidung, wie Trainings-, Radfahr- oder Joggingkleidung und ähnliche Outdoor-Bekleidung. Die empfohlene Beladung beträgt 2.5 kg. Verwenden Sie, um bessere Ergebnisse zu erzielen, keinen Weichspüler und stellen Sie sicher, dass sich keine Weichspülerrückstände in der Waschmittelschublade befinden. Wasserdichtes, atmungsaktives Gewebe.
www.aeg.com Programmtemperatur, maximale Schleuderdrehzahl und maximale Beladung Programm Standardtemperatur Maximale Schleuder- Maximale BelaTemperaturbereich drehzahl dung Schleuderdrehzahlbereich Baumwolle 40 °C 95 °C - kalt 1600 U/min 1600 U/min – 400 U/min 10 kg Pflegeleicht 40 °C 60 °C - kalt 1200 U/min 1200 U/min – 400 U/min 4 kg Feinwäsche 40 °C 40 °C - kalt 1200 U/min 1200 U/min – 400 U/min 4 kg Wolle/Seide 40 °C 40 °C - kalt 1200 U/min 1200 U/min – 400 U/min 1.5 kg - - 1.
DEUTSCH 21 Pflegeleicht Feinwäsche Wolle/Seide Anti-Allergie 20 min. - 3 kg Outdoor Daunen Jeans U./Min.
www.aeg.com 7.2 Woolmark Apparel Care Blau Das Waschprogramm Wolle dieser Maschine wurde von der Firma Woolmark auf das Waschen von Wolltextilien mit der Pflegekennzeichnung „Handwäsche“ getestet und zugelassen, vorausgesetzt, dass die Wäsche gemäß der Anleitung auf dem Kleidungsetikett und gemäß den Angaben des Maschinenherstellers gewaschen wird. Beachten Sie die Trocken- und Waschanleitung auf dem Kleidungsetikett.
DEUTSCH Sind die akustischen Signale ausgeschaltet, ertönen sie nur noch dann, wenn eine Störung vorliegt. 9.3 Extra Spülen dauerhaft einschalten Wenn Sie diese Option wählen, ist bei jeder neuen Programmauswahl die Funktion Extra Spülen eingeschaltet. • Berühren Sie zum Ein-/Ausschalten dieser Option die Tasten Extra Spülen und Option gleichzeitig, bis die zugehörige Anzeige aufleuchtet/ erlischt. Diese Option fügt dem Programm zwei Spülgänge hinzu und das Display zeigt 9.
www.aeg.com 10.3 Einfüllen von Wasch- und Pflegemitteln 1 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. Fach für Vorwäsche und Einweichprogramm. Fach für die Hauptwäsche. Fach für flüssige Pflegemittel (Weichspüler, Stärke). Maximaler Füllstand für flüssige Pflegemittel. Fach für den Fleckentferner. Klappe für Waschpulver oder Flüssigwaschmittel. Halten Sie sich immer an die Anweisungen auf der Verpackung der Waschmittel.
DEUTSCH Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. • Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. • Stellen Sie nicht den Vorwaschgang ein. • Stellen Sie nicht die Zeitvorwahl ein. 5. Messen Sie Waschmittel und Weichspüler ab. 6. Schließen Sie die Waschmittelschublade vorsichtig. 25 3. Schalten Sie bei Bedarf eine oder mehrere Optionen durch Berühren der entsprechenden Tasten ein.
www.aeg.com 2. Berühren Sie die Taste Zeitvorwahl wiederholt, bis im Display erscheint. 3. Berühren Sie die Taste Start/Pause erneut, um das Programm sofort zu starten. Ändern der Zeitvorwahl nach dem Start des Countdowns Ändern der Zeitvorwahl: 1. Berühren Sie die Taste Start/Pause, um das Gerät in den Pausenmodus zu schalten. Die zugehörige Anzeige blinkt. 2. Berühren Sie die Taste Zeitvorwahl wiederholt, bis das Display die gewünschte Zeitvorwahl anzeigt. 3.
DEUTSCH Die Knitterschutzphase wird ausgeführt: . 10.10 Unterbrechen eines Programms und Ändern der Optionen Wenn das Programm bereits gestartet wurde, können Sie nur einige der Optionen ändern: 1. Berühren Sie die Taste Start/Pause. Die zugehörige Kontrolllampe blinkt. 2. Ändern Sie die Optionen. Die im Display angezeigten Informationen ändern sich entsprechend. 3. Berühren Sie die Taste Start/Pause erneut. Das Waschprogramm wird fortgesetzt. 10.11 Abbrechen eines laufenden Programms 1.
www.aeg.com 4. Lassen Sie die Tür und die Waschmittelschublade einen Spaltbreit geöffnet, damit sich kein Schimmel und keine unangenehmen Gerüche bilden. 5. Schließen Sie den Wasserhahn. 10.14 Abpumpen des Wassers nach dem Programmende Wenn Sie ein Programm oder eine Option gewählt haben, nach dem/der die Textilien im Wasser liegen bleiben, ist das Programm beendet, aber: • Im Display erscheint die Anzeige , die Optionsanzeige oder und das Türverriegelungssymbol .
DEUTSCH • • • • • • • und Druckknöpfe. Schließen Sie Gürtel. Leeren Sie die Taschen und stülpen Sie sie nach außen. Wenden Sie mehrlagige Textilien, Wolle und bedruckte Wäschestücke vor dem Waschen. Führen Sie eine Vorbehandlung hartnäckiger Flecken durch. Waschen Sie stark verschmutzte Bereiche mit einem speziellen Waschmittel. Seien Sie vorsichtig mit Gardinen. Entfernen Sie die Haken, oder stecken Sie die Gardinen in ein Wäschenetz oder Kopfkissenbezug.
www.aeg.com Wenden Sie sich an Ihr örtliches Wasserversorgungsunternehmen, um die Wasserhärte in Ihrem Gebiet zu erfahren. Anweisungen auf der Verpackung des Produkts. Verwenden Sie die richtige Menge Wasserenthärter. Halten Sie sich an die 12. REINIGUNG UND PFLEGE WARNUNG! Siehe Kapitel "Sicherheitshinweise". 12.1 Reinigen der Außenseiten Reinigen Sie das Gerät nur mit warmem Wasser und etwas milder Seife. Reiben Sie alle Oberflächen sorgfältig trocken.
DEUTSCH 31 Für eine komplette Reinigung: 1. Reinigen Sie die Trommel mit einem Spezialreiniger für Edelstahl. Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts. 2. Starten Sie ein kurzes Programm für Baumwolle mit hoher Temperatur, leerer Trommel und etwas Waschpulver, um Rückstände auszuspülen. 12.
www.aeg.com 12.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. 1 1 Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. Reinigen Sie die Ablaufpumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht. • Das Gerät macht ein ungewöhnliches Geräusch, weil die Ablaufpumpe blockiert ist. 2 4. Lassen Sie das Wasser ablaufen. • Im Display wird der Alarmcode angezeigt.
DEUTSCH 33 2 2 1 1 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, dass sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst. 12. Schließen Sie die Pumpenabdeckung. 2 1 10. Reinigen Sie das Sieb unter fließendem Wasser. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: a.
www.aeg.com 1 2 45° 3 20° 2. Lockern Sie die Ringmutter, um den Zulaufschlauch vom Gerät zu entfernen. 12.9 Notentleerung Kann das Gerät das Wasser nicht abpumpen, führen Sie den unter „Reinigen des Ablauffilters“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 1.
DEUTSCH 35 WARNUNG! Stellen Sie sicher, dass die Temperatur über 0 °C liegt, bevor Sie das Gerät wieder einschalten. Der Hersteller ist nicht für Schäden verantwortlich, die auf zu niedrige Temperaturen zurückzuführen sind. 13. FEHLERSUCHE WARNUNG! Siehe Kapitel "Sicherheitshinweise". 13.1 Einführung Das Gerät startet nicht oder bleibt während des Betriebs stehen. Versuchen Sie zunächst, selbst eine Lösung für das Problem zu finden (siehe Tabelle).
www.aeg.com 13.2 Mögliche Störungen Störung Mögliche Abhilfe Das Programm startet nicht. Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. Achten Sie darauf, dass die Gerätetür geschlossen ist. Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. Stellen Sie sicher, dass Start/Pause berührt wurde. Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab oder warten Sie, bis sie abgelaufen ist.
DEUTSCH Störung 37 Mögliche Abhilfe Haben Sie ein Programm mit Spülstopp gewählt, stellen Sie das Abpumpprogramm ein. Das Gerät schleudert nicht oder das Waschprogramm dauert länger als gewöhnlich. Stellen Sie das Schleuderprogramm ein. Vergewissern Sie sich, dass das Ablaufsieb nicht verstopft ist. Reinigen Sie ggf. das Sieb. Siehe „Reinigung und Pflege“. Verteilen Sie die Wäschestücke mit der Hand neu und starten Sie die Schleuderphase erneut.
www.aeg.com Störung Mögliche Abhilfe Die Waschergebnisse sind nicht zufriedenstellend. Erhöhen Sie die Waschmittelmenge oder benutzen Sie ein anderes Waschmittel. Entfernen Sie vor dem Waschgang hartnäckige Flecken mit einem Spezialprodukt. Achten Sie darauf, die richtige Temperatur einzustellen. Verringern Sie die Beladung. Zu viel Schaum in der Trommel während des Waschprogramms. Reduzieren Sie die Waschmittelmenge.
DEUTSCH 4. Drücken Sie den Auslöser für die Notfallentriegelung nach unten und öffnen Sie gleichzeitig die Gerätetür. 5. Nehmen Sie die Wäsche heraus und schließen Sie die Gerätetür. 6. Schließen Sie die Filterklappe. 14. VERBRAUCHSWERTE Bei den in dieser Tabelle angegebenen Werten handelt es sich um Richtwerte. Folgende Variablen können diese Werte verändern: Die Wäscheart und -menge, die Wasser- und Raumtemperatur.
www.aeg.com Programme Beladung (kg) Standardprogramm Baumwolle 40 °C EnergieWasserUngeRestverbrauch verbrauch fähre Pro- feuchte (kWh) (Liter) grammda- (%)1) uer (in Minuten) 5 0.59 48 190 44 1) Am Ende der Schleuderphase. Aus-Zustand (W) Ein-Zustand (W) 0.30 0.30 Die in der Tabelle oben enthaltenen Informationen erfüllen die Verordnung (EU) 1015/2010 der Kommission zur Durchführung der Richtlinie EG/2009/125. 15.
DEUTSCH 41 16. ZUBEHÖR 16.1 Verfügbar bei www.aeg.com/shop oder einem autorisierten Händler Waschmaschine auf www.registeraeg.com, um Informationen darüber zu erhalten, wann die Vernetzungsfunktion aktiviert werden kann. Nur mit geeignetem, von AEG zugelassenem Zubehör können die Sicherheitsstandards des Geräts gewährleistet werden. Werden nicht zugelassene Teile verwendet, erlischt jeglicher Gewährleistungsanspruch. 16.
www.aeg.
DEUTSCH 43
132935800-B-172016 www.aeg.