LAVATHERM 7041 TK ELECTRONIC Séchoir à condensation Mode d'emploi
Chère cliente, cher client Veuillez lire attentivement la notice d’utilisation dans son intégralité et la conserver pour pouvoir la consulter ultérieurement. Veuillez la transmettre à l’éventuel futur propriétaire de l’appareil. 1 3 2 2 Les symboles suivants sont utilisés dans ce document : Consignes de sécurité Avertissement ! Conseils pour votre sécurité personnelle. Avertissement ! Consignes permettant d’éviter d’endommager l’appareil.
Sommaire Mode d'emploi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Elimination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Conseils relatifs à l’environnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Description de l’appareil. . . . . . . . . . . . . . . . . .
Caractéristiques techniques. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Données de consommation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Instructions de montage et de raccordement . . . . . . . . . . . 25 Consignes de sécurité pour l’installation . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Enlever les protections de transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Raccordement électrique . . . . . .
Mode d'emploi 1 Consignes de sécurité Avant le tout premier séchage • Veuillez observer les ”instructions de montage et de raccordement” • Avant d’utiliser l’appareil, vérifiez qu’il n’a pas été endommagé au cours du transport. Ne branchez en aucun cas un appareil endommagé. En cas de dommages, adressez-vous à votre livreur. Utilisation réglementaire • Le séchoir ne peut être utilisé que pour sécher le linge domestique habituel.
• Nettoyez régulièrement le condenseur thermique. • Pour les colonnes de lavage/séchage : ne posez aucun objet sur le séchoir. Ils pourraient tomber au cours du séchage. • Le cache de l’ampoule incandescente de l’éclairage du tambour doit être soigneusement vissé. Sécurité des enfants • Ne laissez pas les enfants s’approcher des éléments constituant l’emballage. Risque d’asphyxie ! • Le plus souvent, les enfants ne sont pas conscients des dangers qu’ils encourent en présence d’appareils électriques.
Elimination 2 Emballages 2 1 Les emballages sont respectueux de l’environnement et réutilisables. Les pièces en plastique sont caractérisées par des symboles, par exemple, >PE<>PS< etc. Trier les emballages selon leur nature et les jeter dans les conteneurs prévus à cet effet dans les centres de collecte locaux. Appareils usagés Eliminer les vieux appareils conformément aux directives locales en vigueur. Avertissement ! Débranchez le connecteur des anciens appareils hors d’usage de la prise.
Description de l’appareil Bandeau de commande Bac-tiroir avec bac à eau condensée Filtre fin (filtre à peluches) Ampoule de l’éclairage intérieur Filtre grossier (filtre à peluches) Filtre microfin (filtre à peluches) Plaque signalétique Porte (butée amovible) Clapet du socle recouvrant le condenseur thermique Fente d’aération Pieds de réglage (réglables en hauteur) Bandeau de commande Touche HUMIDITE RESIDUELLE Affichage du degré d’humidité Sélecteur de programmes Multiafficheur Touche Affichage
Avant le tout premier lavage Pour éliminer d’éventuels résidus de fabrication, passez un chiffon humide sur le tambour du séchoir ou procédez à un bref séchage (30 MIN) de torchons humides. Trier et préparer le linge Trier le linge • Trier le linge par type de textile : – Coton/lin pour les programmes de type COTON – Textiles mélangés et synthétiques pour les programmes de type TEXTILES MELANGES. • Trier le linge par type d’étiquettes d’entretine.
Tableau récapitulatif des programmes COTON HUMIDITE RESIDUELLE SENSIBLE 1) ALARME Utilisation/propriétés mn TRES SEC 6kg • • • • SEC 6kg • • • • Séchage complet de textiles épais, par ex. du linge en tissu éponge ou des serviettes éponge. mn mn A RANGER 6kg • • • • Séchage intégral de textiles d’épaisseur homogène, par ex. du linge en tissu éponge, des serviettes éponge ou des lainages. HUMIDE 6kg • • • • Pour textiles fins à repasser, par ex.
30 MIN JEANS FACILE A REPASSER LAINE RAFRAICHIR 1kg 6kg 1kg 1kg 1kg • • • • • • • • • • - • - - - HUMIDITE RESIDUELLE SENSIBLE 1) ALARME DELICAT 1) Programmes Charge max. (poids sec) Fonctions complémentaires Utilisation/propriétés Etiquettes d’entretien - Pour sécher des pièces de linge séparées ou de petites quantités de linge n’excédant pas 1kg. m l2) n mn • Programme spécial pour vêtements de sport comme les jeans, les sweats, etc.
Séchage Mettre l’appareil/l’éclairage sous tension Positionnez le sélecteur de programmes sur n’importe quel programme ou sur ECLAIRAGE. L’appareil est sous tension. Lorsque le hublot est ouvert, le tambour s’éclaire. Ouvrir le hublot/Insérer le linge 1. Ouvrez le hublot : – Vous pouvez soit appuyer fortement sur le hublot (point de pression ) – ou si l’appareil est branché : Appuyer sur la touche PORTE 2. Insérez le linge sans le tasser.
Sélectionner des fonctions complémentaires HUMIDITÉ RÉSIDUELLLE Pour un réglage précis de l’humidité résiduelle du linge. En sélectionnant de + à +++ , on augmente le degré de séchage du linge. 1. Appuyez sur la touche HUMIDITE RESIDUELLE jusqu’à ce que la petite ampoule indiquant la valeur correspondante s’allume. Vous pouvez également appuyer sur les touches DELICAT, ALARME ou SENSIBLE si vous le désirez.
Réglage du départ différé 3 3 La touche DEPART DIFFERE permet de retarder le démarrage d’un programme de 30 minutes (30'jusqu’à max. 23 heures (23 h). 1. Sélectionnez un programme 2. Appuyez sur la touche DEPART DIFFERE jusqu’à ce que la valeur correspondant au délai du démarrage souhaité apparaisse sur le multiafficheur. Ex. 12 h, si le programme doit démarrer dans 12 heures. Le voyant DEPART DIFFERE s’allume.
Ajouter du linge ou en enlever prématurément 1. Ouvrez le hublot 1 Attention ! Le linge et le tambour peuvent être brûlants. Danger de brûlures ! 2. Ajouter du linge ou en enlever. 3. Fermez le hublot en appuyant fortement. Le verrouillage doit être audible. 4. Appuyez sur la touche MARCHE/PAUSE pour poursuivre le programme. Fin du séchage/enlever le linge 3 Lorsque le séchage est terminé, les voyants FIN et ANTIFROISSAGE s’allument.
Nettoyage et entretien Nettoyage des filtres à peluches 1 Pour assurer un fonctionnement impeccable du séchoir, il est nécessaire de nettoyer les filtres à peluches (filtres microfins et filtres fins) après chaque séchage. Attention ! N’utilisez jamais le séchoir sans avoir installé les filtres à peluches ou avec des filtres à peluches endommagés ou bouchés. 1. Ouvrez le hublot 2. Nettoyez le filtre microfin qui se trouve au bas du hublot avec une main humide. 3.
3 Nettoyez l’ensemble de la zone du filtre Il n’est pas nécessaire de nettoyer l’ensemble de la zone du filtre après chaque séchage, mais elle doit être régulièrement contrôlée et, le cas échéant, les peluches enlevées. 6. A cet effet, saisissez le filtre grossier par le haut et tirez-le vers l’avant jusqu’à ce qu’il se détache des deux supports. 7. Enlevez les peluches de l’ensemble de la zone du filtre, de préférence à l’aide d’un aspirateur. 8.
Vider le bac à eau condensée 1 Videz le bac à eau condensée après chaque cycle de séchage. Si le bac à eau condensée est plein, le programme de séchage en cours s’interrompt automatiquement et le voyant BAC s’allume. Il est nécessaire de vider le bac à eau condensée avant de pouvoir poursuivre le programme. Avertissement ! N’utilisez pas l’eau condensée comme eau de boisson ou pour préparer des aliments. 1. Sortez le bac-tiroir contenant le bac à eau condensée intégralement (1).
1. Ouvrez le hublot 2. Ouvrez le clapet du socle : Pour ce faire, appuyez sur le touche de déverrouillage sur la partie inférieure de l’ouverture de remplissage et rabattez le clapet du socle vers la gauche. 3. Enlevez les peluches se trouvant à l’intérieur du hublot et dans l’espace situé devant le condenseur thermique. Nettoyez le joint de la porte à l’aide d’un chiffon humide. 4.
Nettoyage du tambour 1 3 Attention ! Ne nettoyez pas le tambour avec des produits abrasifs ou avec une paille de fer. Le calcaire contenu dans l’eau ou les produits de lavage peuvent laisser un dépôt à peine visible à l’intérieur du tambour. Le degré de séchage détecté risque dans ce cas de ne pas être fiable. Lorsque vous enlevez le linge, il risque d’être plus humide que prévu. Nettoyez l’intérieur et les nervures du tambour avec un nettoyant domestique habituel (par ex.
Symptôme Le séchage n’est pas satisfaisant. Cause possible Solution Vous n’avez pas sélectionné le programme adéquat. Lors du prochain séchage, sélectionnez le programme adéquat (voir chapitre “Tableau récapitulatif des programmes”). les filtres à peluches sont obstrués. Nettoyez les filtres à peluches. Le condenseur thermique est rempli de condensation Nettoyez le condenseur thermique. La charge est inadéquate. Respectez les charges indiquées.
Symptôme Le voyant TEMPS RESTANT saute en permanence ou bien il ne bouge pas pendant un certain temps. Cause possible Solution La durée est constamment C’est un processus automaticorrigée en fonction du type que, l’appareil n’est pas pour de linge, de la charge et du autant défectueux. degré d’humidité. Le programme s’immoLe bac à eau condensée est bilise, le voyant BAC plein. s’allume. Videz le bac à eau condensée puis démarrez le programme en appuyant sur la touche MARCHE/PAUSE.
1. Dévissez le cache de l’ampoule (situé en haut immédiatement derrière le hublot, voir chapitre “Description de l’appareil“) 2. Remplacez l’ampoule défectueuse 3. Revissez soigneusement le cache. 1 Avertissement ! Pour des raisons de sécurité, assurez-vous que le cache est bien vissé. Dans le cas contraire, il est impossible de mettre le séchoir en service. Possibilités de programmations Utilisation Réalisation 1. Positionnez le sélecteur de programmes sur n’importe quel programme. 2.
Caractéristiques techniques 5 Cet appareil est conforme aux directives UE suivantes : – directive 73/23/CEE du 19.02.1973 relative à la basse tension – directive 89/336/CEE du 03.05.1989 relative à la compatibilité électromagnétique (CEM) ainsi qu’à la directive de révision 92/31/CEE – directive 93/68/CEE du 22.07.1993 relative à la certification CE Hauteur x largeur x profondeur 85 x 60 x 60 cm Profondeur hublot ouvert 109 cm Possibilité de réglage de la hauteur 1,5 cm Poids à vide env.
Instructions de montage et de raccordement 1 Consignes de sécurité pour l’installation • Avant de mettre l’appareil en fonctionnement, retirez toutes les protections de transport. Autrement, l’appareil pourrait être endommagé. • Avant de mettre l’appareil en service, assurez-vous que la tension nominale et le type de courant indiqués sur la plaque signalétique correspondent à la tension nominale et au type de courant du lieu de l’installation.
3. Enlevez la gaine plastique avec le rembourrage en polystyrol de l’appareil. Raccordement électrique Les indications relatives au type de courant et au fusible requis se trouvent sur la plaque signalétique. La plaque signalétique se trouve au niveau du hublot (voir chapitre “Description de l’appareil”). Changer la butée du hublot 1 Avertissement ! Le changement de la butée du hublot relève exclusivement de la compétence d’un spécialiste.
5. Dévissez la charnière A de sur le hublot, faites-la tourner de 180 °, replacez-la sur le côté opposé et revissez-la soigneusement. 6. Tournez les caches A et B de 180 ° et replacez-les respectivement sur le côté opposé. 7. Dévissez le cache E de la paroi avant de l’appareil, faites-le tourner de 180 ° et revissez-le sur le côté opposé. 8. Dévissez le verrouillage du hublot, poussez légèrement vers le bas et enlevez-le de la paroi avant de l’appareil. 9. Enlevez le connecteur du verrouillage F du hublot.
Accessoires spéciaux Vous trouverez chez votre distributeur les accessoires spéciaux suivants : Lots de pièces détachées intermédiaires colonne lave-linge/colonne séchoir Ces lots de pièces détachées intermédiaires permettent d’installer le séchoir avec un lave-linge AEG (60cm de large, chargement sur le devant) de manière à constituer une colonne lave-linge/séchoir. Le lave-linge est placé dessous, le séchoir au-dessus.
Centres de service après vente Servicestellen 5506 Mägenwil/Zürich Industriestr. 10 9000 St.
Service après-vente En cas de problèmes techniques, vérifiez d’abord s’il ne vous est pas possible de réparer vous-même le dysfonctionnement à l’aide de la notice d’utilisation (chapitre „Que faire, si...“). Si vous ne parvenez pas à réparer le dysfonctionnement, veuillez contacter notre Consumer Services. Pour pouvoir vous dépanner dans les plus brefs délais, nous nécessitons les informations suivantes : – Désignation du modèle – Numéro du produit (PNC) – Numéro de série (S-No.
From the Electrolux Group. The world´s No.1 choice. Le Groupe Electrolux est le premier fabricant mondial d'appareils de cuisine, d'entretien et d'extérieur. Plus de 55 millions de produits du Groupe Electrolux (tels que réfrigérateurs, cuisinières, lave-linge, aspirateurs, tronçonneuses, tondeuses à gazon) sont vendus chaque année pour un montant d'environ 14 milliards de dollars US dans plus de 150 pays à travers le monde. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.